1 files changed, 82 insertions, 0 deletions
diff --git a/arch/arm/include/asm/arch-armada-xp/config.h b/arch/arm/include/asm/arch-armada-xp/config.h
new file mode 100644
index 0000000000..00ee775a45
--- /dev/null
+++ b/arch/arm/include/asm/arch-armada-xp/config.h
@@ -0,0 +1,82 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Armada XP platforms
+ */
+
+#ifndef _ARMADA_XP_CONFIG_H
+#define _ARMADA_XP_CONFIG_H
+
+#include <asm/arch/soc.h>
+
+#define MV88F78X60 /* for the DDR training bin_hdr code */
+
+#define CONFIG_SYS_CACHELINE_SIZE	32
+
+/*
+ * By default kwbimage.cfg from board specific folder is used
+ * If for some board, different configuration file need to be used,
+ * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
+ */
+#ifndef CONFIG_SYS_KWD_CONFIG
+#define	CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
+#endif /* CONFIG_SYS_KWD_CONFIG */
+
+/* Add target to build it automatically upon "make" */
+#define CONFIG_BUILD_TARGET	"u-boot.kwb"
+
+/* end of 16M scrubbed by training in bootrom */
+#define CONFIG_SYS_INIT_SP_ADDR		0x00FF0000
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+#define MV_UART_CONSOLE_BASE		MVEBU_UART0_BASE
+
+/*
+ * SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_HARD_SPI			1
+#define CONFIG_KIRKWOOD_SPI		1
+#ifndef CONFIG_ENV_SPI_BUS
+# define CONFIG_ENV_SPI_BUS		0
+#endif
+#ifndef CONFIG_ENV_SPI_CS
+# define CONFIG_ENV_SPI_CS		0
+#endif
+#ifndef CONFIG_ENV_SPI_MAX_HZ
+# define CONFIG_ENV_SPI_MAX_HZ		50000000
+#endif
+#endif
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_MII		/* expose smi ove miiphy interface */
+#define CONFIG_MVNETA		/* Enable Marvell Gbe Controller Driver */
+#define CONFIG_PHYLIB
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_PHY_GIGE		/* GbE speed/duplex detect */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#ifndef CONFIG_SYS_I2C_SOFT
+#define CONFIG_I2C_MVTWSI
+#endif
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
+#endif /* _ARMADA_XP_CONFIG_H */