diff options
Diffstat (limited to 'arch/arm/cpu/armv7/omap-common/clocks-common.c')
| -rw-r--r-- | arch/arm/cpu/armv7/omap-common/clocks-common.c | 83 |
1 files changed, 77 insertions, 6 deletions
diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 8e7411d437..03674e609f 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -437,12 +437,15 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) { u32 offset_code; u32 offset = volt_mv; +#ifndef CONFIG_DRA7XX int ret = 0; +#endif if (!volt_mv) return; pmic->pmic_bus_init(); +#ifndef CONFIG_DRA7XX /* See if we can first get the GPIO if needed */ if (pmic->gpio_en) ret = gpio_request(pmic->gpio, "PMIC_GPIO"); @@ -456,7 +459,7 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) /* Pull the GPIO low to select SET0 register, while we program SET1 */ if (pmic->gpio_en) gpio_direction_output(pmic->gpio, 0); - +#endif /* convert to uV for better accuracy in the calculations */ offset *= 1000; @@ -467,9 +470,10 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic) if (pmic->pmic_write(pmic->i2c_slave_addr, vcore_reg, offset_code)) printf("Scaling voltage failed for 0x%x\n", vcore_reg); - +#ifndef CONFIG_DRA7XX if (pmic->gpio_en) gpio_direction_output(pmic->gpio, 1); +#endif } static u32 optimize_vcore_voltage(struct volts const *v) @@ -505,13 +509,79 @@ static u32 optimize_vcore_voltage(struct volts const *v) } /* - * Setup the voltages for vdd_mpu, vdd_core, and vdd_iva - * We set the maximum voltages allowed here because Smart-Reflex is not - * enabled in bootloader. Voltage initialization in the kernel will set - * these to the nominal values after enabling Smart-Reflex + * Setup the voltages for the main SoC core power domains. + * We start with the maximum voltages allowed here, as set in the corresponding + * vcores_data struct, and then scale (usually down) to the fused values that + * are retrieved from the SoC. The scaling happens only if the efuse.reg fields + * are initialised. + * Rail grouping is supported for the DRA7xx SoCs only, therefore the code is + * compiled conditionally. Note that the new code writes the scaled (or zeroed) + * values back to the vcores_data struct for eventual reuse. Zero values mean + * that the corresponding rails are not controlled separately, and are not sent + * to the PMIC. */ void scale_vcores(struct vcores_data const *vcores) { +#if defined(CONFIG_DRA7XX) + int i; + struct volts *pv = (struct volts *)vcores; + struct volts *px; + + for (i=0; i<(sizeof(struct vcores_data)/sizeof(struct volts)); i++) { + debug("%d -> ", pv->value); + if (pv->value) { + /* Handle non-empty members only */ + pv->value = optimize_vcore_voltage(pv); + px = (struct volts *)vcores; + while (px < pv) { + /* + * Scan already handled non-empty members to see + * if we have a group and find the max voltage, + * which is set to the first occurance of the + * particular SMPS; the other group voltages are + * zeroed. + */ + if (px->value) { + if ((pv->pmic->i2c_slave_addr == + px->pmic->i2c_slave_addr) && + (pv->addr == px->addr)) { + /* Same PMIC, same SMPS */ + if (pv->value > px->value) + px->value = pv->value; + + pv->value = 0; + } + } + px++; + } + } + debug("%d\n", pv->value); + pv++; + } + + debug("cor: %d\n", vcores->core.value); + do_scale_vcore(vcores->core.addr, vcores->core.value, vcores->core.pmic); + debug("mpu: %d\n", vcores->mpu.value); + do_scale_vcore(vcores->mpu.addr, vcores->mpu.value, vcores->mpu.pmic); + /* Configure MPU ABB LDO after scale */ + abb_setup((*ctrl)->control_std_fuse_opp_vdd_mpu_2, + (*ctrl)->control_wkup_ldovbb_mpu_voltage_ctrl, + (*prcm)->prm_abbldo_mpu_setup, + (*prcm)->prm_abbldo_mpu_ctrl, + (*prcm)->prm_irqstatus_mpu_2, + OMAP_ABB_MPU_TXDONE_MASK, + OMAP_ABB_FAST_OPP); + + /* The .mm member is not used for the DRA7xx */ + + debug("gpu: %d\n", vcores->gpu.value); + do_scale_vcore(vcores->gpu.addr, vcores->gpu.value, vcores->gpu.pmic); + debug("eve: %d\n", vcores->eve.value); + do_scale_vcore(vcores->eve.addr, vcores->eve.value, vcores->eve.pmic); + debug("iva: %d\n", vcores->iva.value); + do_scale_vcore(vcores->iva.addr, vcores->iva.value, vcores->iva.pmic); + /* Might need udelay(1000) here if debug is enabled to see all prints */ +#else u32 val; val = optimize_vcore_voltage(&vcores->core); @@ -540,6 +610,7 @@ void scale_vcores(struct vcores_data const *vcores) val = optimize_vcore_voltage(&vcores->iva); do_scale_vcore(vcores->iva.addr, val, vcores->iva.pmic); +#endif } static inline void enable_clock_domain(u32 const clkctrl_reg, u32 enable_mode) |
