diff options
Diffstat (limited to 'arch/arm/cpu/armv7/mx6/soc.c')
| -rw-r--r-- | arch/arm/cpu/armv7/mx6/soc.c | 103 |
1 files changed, 100 insertions, 3 deletions
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index 0208cba9cc..172527987d 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -8,6 +8,8 @@ */ #include <common.h> +#include <asm/armv7.h> +#include <asm/pl310.h> #include <asm/errno.h> #include <asm/io.h> #include <asm/arch/imx-regs.h> @@ -41,14 +43,19 @@ u32 get_cpu_rev(void) if (type != MXC_CPU_MX6SL) { reg = readl(&anatop->digprog); + struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; + u32 cfg = readl(&scu->config) & 3; type = ((reg >> 16) & 0xff); if (type == MXC_CPU_MX6DL) { - struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; - u32 cfg = readl(&scu->config) & 3; - if (!cfg) type = MXC_CPU_MX6SOLO; } + + if (type == MXC_CPU_MX6Q) { + if (cfg == 1) + type = MXC_CPU_MX6D; + } + } reg &= 0xff; /* mx6 silicon revision */ return (type << 12) | (reg + 0x10); @@ -62,6 +69,9 @@ u32 __weak get_board_rev(void) if (type == MXC_CPU_MX6SOLO) cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF); + if (type == MXC_CPU_MX6D) + cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF); + return cpurev; } #endif @@ -177,10 +187,41 @@ static void imx_set_wdog_powerdown(bool enable) writew(enable, &wdog2->wmcr); } +static void set_ahb_rate(u32 val) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + u32 reg, div; + + div = get_periph_clk() / val - 1; + reg = readl(&mxc_ccm->cbcdr); + + writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) | + (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr); +} + +static void clear_mmdc_ch_mask(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* Clear MMDC channel mask */ + writel(0, &mxc_ccm->ccdr); +} + int arch_cpu_init(void) { init_aips(); + /* Need to clear MMDC_CHx_MASK to make warm reset work. */ + clear_mmdc_ch_mask(); + + /* + * When low freq boot is enabled, ROM will not set AHB + * freq, so we need to ensure AHB freq is 132MHz in such + * scenario. + */ + if (mxc_get_clock(MXC_ARM_CLK) == 396000000) + set_ahb_rate(132000000); + imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */ #ifdef CONFIG_APBH_DMA @@ -336,3 +377,59 @@ void imx_setup_hdmi(void) writel(reg, &mxc_ccm->chsccdr); } #endif + +#ifndef CONFIG_SYS_L2CACHE_OFF +#define IOMUXC_GPR11_L2CACHE_AS_OCRAM 0x00000002 +void v7_outer_cache_enable(void) +{ + struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE; + unsigned int val; + +#if defined CONFIG_MX6SL + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + val = readl(&iomux->gpr[11]); + if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) { + /* L2 cache configured as OCRAM, reset it */ + val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM; + writel(val, &iomux->gpr[11]); + } +#endif + + writel(0x132, &pl310->pl310_tag_latency_ctrl); + writel(0x132, &pl310->pl310_data_latency_ctrl); + + val = readl(&pl310->pl310_prefetch_ctrl); + + /* Turn on the L2 I/D prefetch */ + val |= 0x30000000; + + /* + * The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0 + * The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2 + * But according to ARM PL310 errata: 752271 + * ID: 752271: Double linefill feature can cause data corruption + * Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2 + * Workaround: The only workaround to this erratum is to disable the + * double linefill feature. This is the default behavior. + */ + +#ifndef CONFIG_MX6Q + val |= 0x40800000; +#endif + writel(val, &pl310->pl310_prefetch_ctrl); + + val = readl(&pl310->pl310_power_ctrl); + val |= L2X0_DYNAMIC_CLK_GATING_EN; + val |= L2X0_STNDBY_MODE_EN; + writel(val, &pl310->pl310_power_ctrl); + + setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN); +} + +void v7_outer_cache_disable(void) +{ + struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE; + + clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN); +} +#endif /* !CONFIG_SYS_L2CACHE_OFF */ |
