diff options
36 files changed, 855 insertions, 17 deletions
@@ -609,6 +609,8 @@ KBUILD_CFLAGS += $(KCFLAGS) UBOOTINCLUDE := \ -Iinclude \ $(if $(KBUILD_SRC), -I$(srctree)/include) \ + $(if $(CONFIG_SYS_THUMB_BUILD), $(if $(CONFIG_HAS_THUMB2),, \ + -I$(srctree)/arch/$(ARCH)/thumb1/include),) \ -I$(srctree)/arch/$(ARCH)/include \ -include $(srctree)/include/linux/kconfig.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 0d756cbc55..5ab0254f3b 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -10,6 +10,9 @@ config ARM64 config HAS_VBAR bool +config HAS_THUMB2 + bool + config CPU_ARM720T bool @@ -32,9 +35,11 @@ config CPU_ARM1176 config CPU_V7 bool select HAS_VBAR + select HAS_THUMB2 config CPU_V7M bool + select HAS_THUMB2 config CPU_PXA bool diff --git a/arch/arm/cpu/arm926ejs/Makefile b/arch/arm/cpu/arm926ejs/Makefile index 63fa159db6..fe78922170 100644 --- a/arch/arm/cpu/arm926ejs/Makefile +++ b/arch/arm/cpu/arm926ejs/Makefile @@ -20,3 +20,14 @@ obj-$(CONFIG_MX25) += mx25/ obj-$(CONFIG_MX27) += mx27/ obj-$(if $(filter mxs,$(SOC)),y) += mxs/ obj-$(if $(filter spear,$(SOC)),y) += spear/ + +# some files can only build in ARM or THUMB2, not THUMB1 + +ifdef CONFIG_SYS_THUMB_BUILD +ifndef CONFIG_HAS_THUMB2 + +CFLAGS_cpu.o := -marm +CFLAGS_cache.o := -marm + +endif +endif diff --git a/arch/arm/cpu/arm926ejs/cache.c b/arch/arm/cpu/arm926ejs/cache.c index e5c1a6ae6c..2839c863e8 100644 --- a/arch/arm/cpu/arm926ejs/cache.c +++ b/arch/arm/cpu/arm926ejs/cache.c @@ -82,4 +82,9 @@ void flush_dcache_all(void) /* * Stub implementations for l2 cache operations */ + __weak void l2_cache_disable(void) {} + +#if defined CONFIG_SYS_THUMB_BUILD +__weak void invalidate_l2_cache(void) {} +#endif diff --git a/arch/arm/cpu/armv7m/stm32f4/flash.c b/arch/arm/cpu/armv7m/stm32f4/flash.c index e5c6111330..dd058bd643 100644 --- a/arch/arm/cpu/armv7m/stm32f4/flash.c +++ b/arch/arm/cpu/armv7m/stm32f4/flash.c @@ -97,6 +97,9 @@ int flash_erase(flash_info_t *info, int first, int last) while (readl(&STM32_FLASH->sr) & STM32_FLASH_SR_BSY) ; + /* clear old sector number before writing a new one */ + clrbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_SNB_MASK); + if (bank == 0) { setbits_le32(&STM32_FLASH->cr, (i << STM32_FLASH_CR_SNB_OFFSET)); @@ -114,9 +117,9 @@ int flash_erase(flash_info_t *info, int first, int last) ; clrbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_SER); - stm32f4_flash_lock(1); } + stm32f4_flash_lock(1); return 0; } diff --git a/arch/arm/cpu/armv8/cache_v8.c b/arch/arm/cpu/armv8/cache_v8.c index b1ea8227cb..1ece6a2c12 100644 --- a/arch/arm/cpu/armv8/cache_v8.c +++ b/arch/arm/cpu/armv8/cache_v8.c @@ -32,7 +32,7 @@ inline void set_pgtable_table(u64 *page_table, u64 index, u64 *table_addr) } /* to activate the MMU we need to set up virtual memory */ -static void mmu_setup(void) +__weak void mmu_setup(void) { bd_t *bd = gd->bd; u64 *page_table = (u64 *)gd->arch.tlb_addr, i, j; diff --git a/arch/arm/include/asm/arch-stm32f4/stm32.h b/arch/arm/include/asm/arch-stm32f4/stm32.h index 3ed3801dfe..7ca6dc3de8 100644 --- a/arch/arm/include/asm/arch-stm32f4/stm32.h +++ b/arch/arm/include/asm/arch-stm32f4/stm32.h @@ -104,6 +104,7 @@ struct stm32_flash_regs { #define STM32_FLASH_CR_STRT (1 << 16) #define STM32_FLASH_CR_LOCK (1 << 31) #define STM32_FLASH_CR_SNB_OFFSET 3 +#define STM32_FLASH_CR_SNB_MASK (15 << STM32_FLASH_CR_SNB_OFFSET) enum clock { CLOCK_CORE, diff --git a/arch/arm/include/asm/cache.h b/arch/arm/include/asm/cache.h index a836e9f2ab..1f63127bdc 100644 --- a/arch/arm/include/asm/cache.h +++ b/arch/arm/include/asm/cache.h @@ -16,6 +16,9 @@ /* * Invalidate L2 Cache using co-proc instruction */ +#ifdef CONFIG_SYS_THUMB_BUILD +void invalidate_l2_cache(void); +#else static inline void invalidate_l2_cache(void) { unsigned int val=0; @@ -24,6 +27,7 @@ static inline void invalidate_l2_cache(void) : : "r" (val) : "cc"); isb(); } +#endif void l2_cache_enable(void); void l2_cache_disable(void); diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h index cfc7834ed9..71b31085b4 100644 --- a/arch/arm/include/asm/system.h +++ b/arch/arm/include/asm/system.h @@ -17,6 +17,7 @@ #define PGTABLE_SIZE (0x10000) /* 2MB granularity */ #define MMU_SECTION_SHIFT 21 +#define MMU_SECTION_SIZE (1 << MMU_SECTION_SHIFT) #ifndef __ASSEMBLY__ @@ -278,11 +279,6 @@ enum { */ void mmu_page_table_flush(unsigned long start, unsigned long stop); -#ifdef CONFIG_SYS_NONCACHED_MEMORY -void noncached_init(void); -phys_addr_t noncached_alloc(size_t size, size_t align); -#endif /* CONFIG_SYS_NONCACHED_MEMORY */ - #endif /* __ASSEMBLY__ */ #define arch_align_stack(x) (x) @@ -302,6 +298,11 @@ phys_addr_t noncached_alloc(size_t size, size_t align); void mmu_set_region_dcache_behaviour(phys_addr_t start, size_t size, enum dcache_option option); +#ifdef CONFIG_SYS_NONCACHED_MEMORY +void noncached_init(void); +phys_addr_t noncached_alloc(size_t size, size_t align); +#endif /* CONFIG_SYS_NONCACHED_MEMORY */ + #endif /* __ASSEMBLY__ */ #endif diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile index 2bdfaba5b7..f3db7b58cb 100644 --- a/arch/arm/lib/Makefile +++ b/arch/arm/lib/Makefile @@ -60,3 +60,27 @@ obj-$(CONFIG_DEBUG_LL) += debug.o ifneq (,$(findstring -mabi=aapcs-linux,$(PLATFORM_CPPFLAGS))) extra-y += eabi_compat.o endif + +# some files can only build in ARM or THUMB2, not THUMB1 + +ifdef CONFIG_SYS_THUMB_BUILD +ifndef CONFIG_HAS_THUMB2 + +# for C files, just apend -marm, which will override previous -mthumb* + +CFLAGS_cache.o := -marm +CFLAGS_cache-cp15.o := -marm + +# For .S, drop -mthumb* and other thumb-related options. +# CFLAGS_REMOVE_* would not have an effet, so AFLAGS_REMOVE_* +# was implemented and is used here. +# Also, define ${target}_NO_THUMB_BUILD for these two targets +# so that the code knows it should not use Thumb. + +AFLAGS_REMOVE_memset.o := -mthumb -mthumb-interwork +AFLAGS_REMOVE_memcpy.o := -mthumb -mthumb-interwork +AFLAGS_memset.o := -DMEMSET_NO_THUMB_BUILD +AFLAGS_memcpy.o := -DMEMCPY_NO_THUMB_BUILD + +endif +endif diff --git a/arch/arm/lib/cache.c b/arch/arm/lib/cache.c index cd13db3440..3bd87105c5 100644 --- a/arch/arm/lib/cache.c +++ b/arch/arm/lib/cache.c @@ -88,3 +88,14 @@ phys_addr_t noncached_alloc(size_t size, size_t align) return next; } #endif /* CONFIG_SYS_NONCACHED_MEMORY */ + +#if defined(CONFIG_SYS_THUMB_BUILD) +void invalidate_l2_cache(void) +{ + unsigned int val = 0; + + asm volatile("mcr p15, 1, %0, c15, c11, 0 @ invl l2 cache" + : : "r" (val) : "cc"); + isb(); +} +#endif diff --git a/arch/arm/lib/memcpy.S b/arch/arm/lib/memcpy.S index eeaf003529..7d9fc0f9be 100644 --- a/arch/arm/lib/memcpy.S +++ b/arch/arm/lib/memcpy.S @@ -13,7 +13,7 @@ #include <linux/linkage.h> #include <asm/assembler.h> -#ifdef CONFIG_SYS_THUMB_BUILD +#if defined(CONFIG_SYS_THUMB_BUILD) && !defined(MEMCPY_NO_THUMB_BUILD) #define W(instr) instr.w #else #define W(instr) instr @@ -62,7 +62,7 @@ /* Prototype: void *memcpy(void *dest, const void *src, size_t n); */ .syntax unified -#ifdef CONFIG_SYS_THUMB_BUILD +#if defined(CONFIG_SYS_THUMB_BUILD) && !defined(MEMCPY_NO_THUMB_BUILD) .thumb .thumb_func #endif diff --git a/arch/arm/lib/memset.S b/arch/arm/lib/memset.S index 7208f20dda..df053a31d5 100644 --- a/arch/arm/lib/memset.S +++ b/arch/arm/lib/memset.S @@ -16,7 +16,7 @@ .align 5 .syntax unified -#ifdef CONFIG_SYS_THUMB_BUILD +#if defined(CONFIG_SYS_THUMB_BUILD) && !defined(MEMSET_NO_THUMB_BUILD) .thumb .thumb_func #endif diff --git a/arch/arm/lib/semihosting.c b/arch/arm/lib/semihosting.c index c3e964eabc..e32ad90945 100644 --- a/arch/arm/lib/semihosting.c +++ b/arch/arm/lib/semihosting.c @@ -31,6 +31,8 @@ static noinline long smh_trap(unsigned int sysnum, void *addr) register long result asm("r0"); #if defined(CONFIG_ARM64) asm volatile ("hlt #0xf000" : "=r" (result) : "0"(sysnum), "r"(addr)); +#elif defined(CONFIG_CPU_V7M) + asm volatile ("bkpt #0xAB" : "=r" (result) : "0"(sysnum), "r"(addr)); #else /* Note - untested placeholder */ asm volatile ("svc #0x123456" : "=r" (result) : "0"(sysnum), "r"(addr)); @@ -90,7 +92,7 @@ static long smh_read(long fd, void *memp, size_t len) size_t len; } read; - debug("%s: fd %ld, memp %p, len %lu\n", __func__, fd, memp, len); + debug("%s: fd %ld, memp %p, len %zu\n", __func__, fd, memp, len); read.fd = fd; read.memp = memp; @@ -104,7 +106,7 @@ static long smh_read(long fd, void *memp, size_t len) * hard to maintain partial read loops and such, just fail * with an error message. */ - printf("%s: ERROR ret %ld, fd %ld, len %lu memp %p\n", + printf("%s: ERROR ret %ld, fd %ld, len %zu memp %p\n", __func__, ret, fd, len, memp); return -1; } diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index aab5d19b5f..f7737bfb22 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -4,6 +4,9 @@ choice prompt "Marvell Kirkwood board select" optional +config TARGET_OPENRD + bool "Marvell OpenRD Board" + config TARGET_DREAMPLUG bool "DreamPlug Board" @@ -51,6 +54,7 @@ endchoice config SYS_SOC default "kirkwood" +source "board/Marvell/openrd/Kconfig" source "board/Marvell/dreamplug/Kconfig" source "board/Marvell/guruplug/Kconfig" source "board/Marvell/sheevaplug/Kconfig" diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile index df4756e4bd..5abcf70b28 100644 --- a/arch/arm/mach-kirkwood/Makefile +++ b/arch/arm/mach-kirkwood/Makefile @@ -9,3 +9,9 @@ obj-y = cpu.o obj-y += cache.o obj-y += mpp.o + +# cpu.o and cache.o contain CP15 instructions which cannot be run in +# Thumb state, so build them for ARM state even with CONFIG_SYS_THUMB_BUILD + +CFLAGS_cpu.o := -marm +CFLAGS_cache.o := -marm diff --git a/arch/arm/mach-orion5x/Makefile b/arch/arm/mach-orion5x/Makefile index 546ebcb52e..33dcad40f2 100644 --- a/arch/arm/mach-orion5x/Makefile +++ b/arch/arm/mach-orion5x/Makefile @@ -16,3 +16,13 @@ obj-y += timer.o ifndef CONFIG_SKIP_LOWLEVEL_INIT obj-y += lowlevel_init.o endif + +# some files can only build in ARM or THUMB2, not THUMB1 + +ifdef CONFIG_SYS_THUMB_BUILD +ifndef CONFIG_HAS_THUMB2 + +CFLAGS_cpu.o := -marm + +endif +endif diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile index 75924ad848..98431a91f8 100644 --- a/arch/arm/mach-tegra/Makefile +++ b/arch/arm/mach-tegra/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_CMD_ENTERRCM) += cmd_enterrcm.o obj-$(CONFIG_PWM_TEGRA) += pwm.o endif +obj-$(CONFIG_ARM64) += arm64-mmu.o obj-y += ap.o obj-y += board.o board2.o obj-y += cache.o diff --git a/arch/arm/mach-tegra/arm64-mmu.c b/arch/arm/mach-tegra/arm64-mmu.c new file mode 100644 index 0000000000..c2276523cb --- /dev/null +++ b/arch/arm/mach-tegra/arm64-mmu.c @@ -0,0 +1,131 @@ +/* + * (C) Copyright 2014 - 2015 Xilinx, Inc. + * Michal Simek <michal.simek@xilinx.com> + * (This file derived from arch/arm/cpu/armv8/zynqmp/cpu.c) + * + * Copyright (c) 2015, NVIDIA CORPORATION. All rights reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/system.h> +#include <asm/armv8/mmu.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define SECTION_SHIFT_L1 30UL +#define SECTION_SHIFT_L2 21UL +#define BLOCK_SIZE_L0 0x8000000000UL +#define BLOCK_SIZE_L1 (1 << SECTION_SHIFT_L1) +#define BLOCK_SIZE_L2 (1 << SECTION_SHIFT_L2) + +#define TCR_TG1_4K (1 << 31) +#define TCR_EPD1_DISABLE (1 << 23) +#define TEGRA_VA_BITS 40 +#define TEGRA_TCR TCR_TG1_4K | \ + TCR_EPD1_DISABLE | \ + TCR_SHARED_OUTER | \ + TCR_SHARED_INNER | \ + TCR_IRGN_WBWA | \ + TCR_ORGN_WBWA | \ + TCR_T0SZ(TEGRA_VA_BITS) + +#define MEMORY_ATTR PMD_SECT_AF | PMD_SECT_INNER_SHARE | \ + PMD_ATTRINDX(MT_NORMAL) | \ + PMD_TYPE_SECT +#define DEVICE_ATTR PMD_SECT_AF | PMD_SECT_PXN | \ + PMD_SECT_UXN | PMD_ATTRINDX(MT_DEVICE_NGNRNE) | \ + PMD_TYPE_SECT + +/* 4K size is required to place 512 entries in each level */ +#define TLB_TABLE_SIZE 0x1000 + +/* + * This mmu table looks as below + * Level 0 table contains two entries to 512GB sizes. One is Level1 Table 0 + * and other Level1 Table1. + * Level1 Table0 contains entries for each 1GB from 0 to 511GB. + * Level1 Table1 contains entries for each 1GB from 512GB to 1TB. + * Level2 Table0, Level2 Table1, Level2 Table2 and Level2 Table3 contains + * entries for each 2MB starting from 0GB, 1GB, 2GB and 3GB respectively. + */ +void mmu_setup(void) +{ + int el; + u64 i, section_l1t0, section_l1t1; + u64 section_l2t0, section_l2t1, section_l2t2, section_l2t3; + u64 *level0_table = (u64 *)gd->arch.tlb_addr; + u64 *level1_table_0 = (u64 *)(gd->arch.tlb_addr + TLB_TABLE_SIZE); + u64 *level1_table_1 = (u64 *)(gd->arch.tlb_addr + (2 * TLB_TABLE_SIZE)); + u64 *level2_table_0 = (u64 *)(gd->arch.tlb_addr + (3 * TLB_TABLE_SIZE)); + u64 *level2_table_1 = (u64 *)(gd->arch.tlb_addr + (4 * TLB_TABLE_SIZE)); + u64 *level2_table_2 = (u64 *)(gd->arch.tlb_addr + (5 * TLB_TABLE_SIZE)); + u64 *level2_table_3 = (u64 *)(gd->arch.tlb_addr + (6 * TLB_TABLE_SIZE)); + + /* Invalidate all table entries */ + memset(level0_table, 0, PGTABLE_SIZE); + + level0_table[0] = + (u64)level1_table_0 | PMD_TYPE_TABLE; + level0_table[1] = + (u64)level1_table_1 | PMD_TYPE_TABLE; + + /* + * set level 1 table 0, covering 0 to 512GB + * set level 1 table 1, covering 512GB to 1TB + */ + section_l1t0 = 0; + section_l1t1 = BLOCK_SIZE_L0; + + for (i = 0; i < 512; i++) { + level1_table_0[i] = section_l1t0; + if (i >= 4) + level1_table_0[i] |= MEMORY_ATTR; + level1_table_1[i] = section_l1t1; + level1_table_1[i] |= MEMORY_ATTR; + section_l1t0 += BLOCK_SIZE_L1; + section_l1t1 += BLOCK_SIZE_L1; + } + + level1_table_0[0] = + (u64)level2_table_0 | PMD_TYPE_TABLE; + level1_table_0[1] = + (u64)level2_table_1 | PMD_TYPE_TABLE; + level1_table_0[2] = + (u64)level2_table_2 | PMD_TYPE_TABLE; + level1_table_0[3] = + (u64)level2_table_3 | PMD_TYPE_TABLE; + + section_l2t0 = 0; + section_l2t1 = section_l2t0 + BLOCK_SIZE_L1; /* 1GB */ + section_l2t2 = section_l2t1 + BLOCK_SIZE_L1; /* 2GB */ + section_l2t3 = section_l2t2 + BLOCK_SIZE_L1; /* 3GB */ + + for (i = 0; i < 512; i++) { + level2_table_0[i] = section_l2t0 | DEVICE_ATTR; + level2_table_1[i] = section_l2t1 | DEVICE_ATTR; + level2_table_2[i] = section_l2t2 | MEMORY_ATTR; + level2_table_3[i] = section_l2t3 | MEMORY_ATTR; + section_l2t0 += BLOCK_SIZE_L2; + section_l2t1 += BLOCK_SIZE_L2; + section_l2t2 += BLOCK_SIZE_L2; + section_l2t3 += BLOCK_SIZE_L2; + } + + /* flush new MMU table */ + flush_dcache_range(gd->arch.tlb_addr, + gd->arch.tlb_addr + gd->arch.tlb_size); + + /* point TTBR to the new table */ + el = current_el(); + set_ttbr_tcr_mair(el, gd->arch.tlb_addr, + TEGRA_TCR, MEMORY_ATTRIBUTES); + + set_sctlr(get_sctlr() | CR_M); +} + +u64 *arch_get_page_table(void) +{ + return (u64 *)(gd->arch.tlb_addr + (3 * TLB_TABLE_SIZE)); +} diff --git a/arch/arm/thumb1/include/asm/proc-armv/system.h b/arch/arm/thumb1/include/asm/proc-armv/system.h new file mode 100644 index 0000000000..7dfbf3d33d --- /dev/null +++ b/arch/arm/thumb1/include/asm/proc-armv/system.h @@ -0,0 +1,69 @@ +/* + * Thumb-1 drop-in for the linux/include/asm-arm/proc-armv/system.h + * + * (C) Copyright 2015 + * Albert ARIBAUD <albert.u.boot@aribaud.net> + * + * The original file does not build in Thumb mode. However, in U-Boot + * we don't use interrupt context, so we can redefine these as empty + * memory barriers, which makes Thumb-1 compiler happy. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Use the same macro name as linux/include/asm-arm/proc-armv/system.h + * here, so that if the original ever gets included after us, it won't + * try to re-redefine anything. + */ + +#ifndef __ASM_PROC_SYSTEM_H +#define __ASM_PROC_SYSTEM_H + +/* + * Redefine all original macros with static inline functions containing + * a simple memory barrier, so that they produce the same instruction + * ordering constraints as their original counterparts. + * We use static inline functions rather than macros so that we can tell + * the compiler to not complain about unused arguments. + */ + +static inline void local_irq_save( + unsigned long flags __attribute__((unused))) +{ + __asm__ __volatile__ ("" : : : "memory"); +} + +static inline void local_irq_enable(void) +{ + __asm__ __volatile__ ("" : : : "memory"); +} + +static inline void local_irq_disable(void) +{ + __asm__ __volatile__ ("" : : : "memory"); +} + +static inline void __stf(void) +{ + __asm__ __volatile__ ("" : : : "memory"); +} + +static inline void __clf(void) +{ + __asm__ __volatile__ ("" : : : "memory"); +} + +static inline void local_save_flags( + unsigned long flags __attribute__((unused))) +{ + __asm__ __volatile__ ("" : : : "memory"); +} + +static inline void local_irq_restore( + unsigned long flags __attribute__((unused))) +{ + __asm__ __volatile__ ("" : : : "memory"); +} + +#endif /* __ASM_PROC_SYSTEM_H */ diff --git a/board/Marvell/openrd/Kconfig b/board/Marvell/openrd/Kconfig new file mode 100644 index 0000000000..124b66da0f --- /dev/null +++ b/board/Marvell/openrd/Kconfig @@ -0,0 +1,12 @@ +if TARGET_OPENRD + +config SYS_BOARD + default "openrd" + +config SYS_VENDOR + default "Marvell" + +config SYS_CONFIG_NAME + default "openrd" + +endif diff --git a/board/Marvell/openrd/MAINTAINERS b/board/Marvell/openrd/MAINTAINERS new file mode 100644 index 0000000000..3789a04c89 --- /dev/null +++ b/board/Marvell/openrd/MAINTAINERS @@ -0,0 +1,12 @@ +OPENRD BOARD +M: Albert ARIBAUD <albert-u-boot@aribaud.net> +S: Maintained +F: board/Marvell/openrd/ +F: include/configs/openrd.h +F: configs/openrd_base_defconfig + +OPENRD_CLIENT BOARD +M: Albert ARIBAUD <albert-u-boot@aribaud.net> +S: Maintained +F: configs/openrd_client_defconfig +F: configs/openrd_ultimate_defconfig diff --git a/board/Marvell/openrd/Makefile b/board/Marvell/openrd/Makefile new file mode 100644 index 0000000000..8f95b7922e --- /dev/null +++ b/board/Marvell/openrd/Makefile @@ -0,0 +1,14 @@ +# +# (C) Copyright 2009 +# Net Insight <www.netinsight.net> +# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> +# +# Based on sheevaplug: +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := openrd.o diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg new file mode 100644 index 0000000000..8e5993715e --- /dev/null +++ b/board/Marvell/openrd/kwbimage.cfg @@ -0,0 +1,152 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x000000cc # DDR Address Control +# bit1-0: 00, Cs0width=x8 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs1width=x8 +# bit7-6: 11, Cs1size=1Gb +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000042 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 1, DDR drive strength reduced +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low) +# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1 +# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0 +# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1. +# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0. +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) + +DATA 0xFFD0149C 0x0000E40f # CPU ODT Control +# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3 +# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm +# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm +# bit14: 1, M_STARTBURST_IN ODT: Enabled +# bit15: 1, DDR IO ODT Unit: Use ODT block +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c new file mode 100644 index 0000000000..17a65600e4 --- /dev/null +++ b/board/Marvell/openrd/openrd.c @@ -0,0 +1,160 @@ +/* + * (C) Copyright 2009 + * Net Insight <www.netinsight.net> + * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> + * + * Based on sheevaplug.c: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <miiphy.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> +#include <asm/arch/mpp.h> +#include "openrd.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + mvebu_config_gpio(OPENRD_OE_VAL_LOW, + OPENRD_OE_VAL_HIGH, + OPENRD_OE_LOW, OPENRD_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + static const u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, /* Alt UART1_TXD */ + MPP14_SD_D0, /* Alt UART1_RXD */ + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_TSMP9, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GPIO, /* UART1 / SD sel */ + MPP35_TDM_CH0_TX_QL, + MPP36_TDM_SPI_CS1, + MPP37_TDM_CH2_TX_QL, + MPP38_TDM_CH2_RX_QL, + MPP39_AUDIO_I2SBCLK, + MPP40_AUDIO_I2SDO, + MPP41_AUDIO_I2SLRC, + MPP42_AUDIO_I2SMCLK, + MPP43_AUDIO_I2SDI, + MPP44_AUDIO_EXTCLK, + MPP45_TDM_PCLK, + MPP46_TDM_FS, + MPP47_TDM_DRX, + MPP48_TDM_DTX, + MPP49_TDM_CH0_RX_QL, + 0 + }; + + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ + /* + * arch number of board + */ +#if defined(CONFIG_BOARD_IS_OPENRD_BASE) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE; +#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT; +#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE; +#endif + + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +/* Configure and enable MV88E1116/88E1121 PHY */ +void mv_phy_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) { + printf("Err..%s could not read PHY dev address\n", __func__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); + + /* reset the phy */ + miiphy_reset(name, devadr); + + printf(PHY_NO" Initialized on %s\n", name); +} + +void reset_phy(void) +{ + mv_phy_init("egiga0"); + +#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT + /* Kirkwood ethernet driver is written with the assumption that in case + * of multiple PHYs, their addresses are consecutive. But unfortunately + * in case of OpenRD-Client, PHY addresses are not consecutive.*/ + miiphy_write("egiga1", 0xEE, 0xEE, 24); +#endif + +#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \ + defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) + /* configure and initialize both PHY's */ + mv_phy_init("egiga1"); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/openrd/openrd.h b/board/Marvell/openrd/openrd.h new file mode 100644 index 0000000000..56dfeea1a8 --- /dev/null +++ b/board/Marvell/openrd/openrd.h @@ -0,0 +1,30 @@ +/* + * (C) Copyright 2009 + * Net Insight <www.netinsight.net> + * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> + * + * Based on sheevaplug.h: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __OPENRD_BASE_H +#define __OPENRD_BASE_H + +#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */ +#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */ +#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */ +#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */ + +/* PHY related */ +#define MV88E1116_LED_FCTRL_REG 10 +#define MV88E1116_CPRSP_CR3_REG 21 +#define MV88E1116_MAC_CTRL_REG 21 +#define MV88E1116_PGADR_REG 22 +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) + +#endif /* __OPENRD_BASE_H */ diff --git a/board/freescale/ls1043ardb/MAINTAINERS b/board/freescale/ls1043ardb/MAINTAINERS index b8f6be249f..efca5bf245 100644 --- a/board/freescale/ls1043ardb/MAINTAINERS +++ b/board/freescale/ls1043ardb/MAINTAINERS @@ -5,3 +5,5 @@ F: board/freescale/ls1043ardb/ F: board/freescale/ls1043ardb/ls1043ardb.c F: include/configs/ls1043ardb.h F: configs/ls1043ardb_defconfig +F: configs/ls1043ardb_nand_defconfig +F: configs/ls1043ardb_sdcard_defconfig diff --git a/configs/openrd_base_defconfig b/configs/openrd_base_defconfig new file mode 100644 index 0000000000..16861397c3 --- /dev/null +++ b/configs/openrd_base_defconfig @@ -0,0 +1,7 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_TARGET_OPENRD=y +CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_BASE" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set diff --git a/configs/openrd_client_defconfig b/configs/openrd_client_defconfig new file mode 100644 index 0000000000..c34231560c --- /dev/null +++ b/configs/openrd_client_defconfig @@ -0,0 +1,7 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_TARGET_OPENRD=y +CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_CLIENT" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set diff --git a/configs/openrd_ultimate_defconfig b/configs/openrd_ultimate_defconfig new file mode 100644 index 0000000000..530ba4d10c --- /dev/null +++ b/configs/openrd_ultimate_defconfig @@ -0,0 +1,7 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_TARGET_OPENRD=y +CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_ULTIMATE" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 728acddb5a..b7cf62df9b 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -64,9 +64,6 @@ nhk8815 arm arm926ejs 0abdd9d0 2015-08-30 Nomadik Linu nhk8815_onenand arm arm926ejs 0abdd9d0 2015-08-30 Nomadik Linux Team <STN_WMM_nomadik_linux@list.st.com> omap3_mvblx arm armv7 8dc372f9 2015-08-30 Michael Jones <michael.jones@matrix-vision.de> omap3_sdp3430 arm armv7 93b25c08 2015-08-30 Nishanth Menon <nm@ti.com> -openrd_base arm arm926ejs 7a2c1b13 2015-08-30 Prafulla Wadaskar <prafulla@marvell.com> -openrd_client arm arm926ejs 7a2c1b13 2015-08-30 Prafulla Wadaskar <prafulla@marvell.com> -openrd_ultimate arm arm926ejs 7a2c1b13 2015-08-30 Prafulla Wadaskar <prafulla@marvell.com> otc570 arm arm926ejs 819216dd 2015-08-30 Daniel Gorsulowski <daniel.gorsulowski@esd.eu> otc570_dataflash arm arm926ejs 819216dd 2015-08-30 Daniel Gorsulowski <daniel.gorsulowski@esd.eu> palmld arm pxa 35782e9c 2015-08-30 Marek Vasut <marex@denx.de> diff --git a/examples/standalone/Makefile b/examples/standalone/Makefile index 0863a8cda2..5a6ae0013c 100644 --- a/examples/standalone/Makefile +++ b/examples/standalone/Makefile @@ -73,3 +73,13 @@ $(obj)/%.srec: $(obj)/% FORCE $(obj)/%.bin: OBJCOPYFLAGS := -O binary $(obj)/%.bin: $(obj)/% FORCE $(call if_changed,objcopy) + +# some files can only build in ARM or THUMB2, not THUMB1 + +ifdef CONFIG_SYS_THUMB_BUILD +ifndef CONFIG_HAS_THUMB2 + +CFLAGS_stubs.o := -marm + +endif +endif diff --git a/include/configs/openrd.h b/include/configs/openrd.h new file mode 100644 index 0000000000..62f15b7688 --- /dev/null +++ b/include/configs/openrd.h @@ -0,0 +1,138 @@ +/* + * (C) Copyright 2009 + * Net Insight <www.netinsight.net> + * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> + * + * Based on sheevaplug.h: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_OPENRD_H +#define _CONFIG_OPENRD_H + +/* + * Version number information + */ +#ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE +# define CONFIG_IDENT_STRING "\nOpenRD-Ultimate" +#else +# ifdef CONFIG_BOARD_IS_OPENRD_CLIENT +# define CONFIG_IDENT_STRING "\nOpenRD-Client" +# else +# ifdef CONFIG_BOARD_IS_OPENRD_BASE +# define CONFIG_IDENT_STRING "\nOpenRD-Base" +# else +# error Unknown OpenRD board specified +# endif +# endif +#endif + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ +#define CONFIG_KW88F6281 1 /* SOC Name */ +#define CONFIG_MACH_OPENRD_BASE /* Machine type */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ +#define CONFIG_SYS_THUMB_BUILD + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_SYS_MVFS +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_MII +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NAND +#define CONFIG_CMD_PING +#define CONFIG_CMD_USB +#define CONFIG_CMD_IDE + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* + * Environment variables configurations + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ +#else +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ +#endif +/* + * max 4k env size is enough, but in case of nand + * it has to be rounded to sector size + */ +#define CONFIG_ENV_SIZE 0x20000 /* 128k */ +#define CONFIG_ENV_ADDR 0x60000 +#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ +/* + * Environment is right behind U-Boot in flash. Make sure U-Boot + * doesn't grow into the environment area. + */ +#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET + +/* + * Default environment variables + */ +#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ + "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ + "${x_bootcmd_usb}; bootm 0x6400000;" + +#define MTDIDS_DEFAULT "nand0=nand_mtd" +#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\ + "0x400000@0x100000(uImage),"\ + "0x1fb00000@0x500000(rootfs)" + +#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \ + "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ + "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ + "x_bootcmd_usb=usb start\0" \ + "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \ + "mtdids="MTDIDS_DEFAULT"\0" \ + "mtdparts="MTDPARTS_DEFAULT"\0" + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +# ifdef CONFIG_BOARD_IS_OPENRD_BASE +# define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ +# else +# define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ +# endif +# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE +# define CONFIG_PHY_BASE_ADR 0x0 +# define PHY_NO "88E1121" +# else +# define CONFIG_PHY_BASE_ADR 0x8 +# define PHY_NO "88E1116" +# endif +#endif /* CONFIG_CMD_NET */ + +/* + * SATA Driver configuration + */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ + +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_MVEBU_MMC +#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE +#endif /* CONFIG_CMD_MMC */ + +#endif /* _CONFIG_OPENRD_BASE_H */ diff --git a/include/configs/stm32f429-discovery.h b/include/configs/stm32f429-discovery.h index 17969952d1..8191fb2b8a 100644 --- a/include/configs/stm32f429-discovery.h +++ b/include/configs/stm32f429-discovery.h @@ -9,6 +9,7 @@ #define __CONFIG_H #define CONFIG_STM32F4 +#define CONFIG_SYS_THUMB_BUILD #define CONFIG_STM32F4DISCOVERY #define CONFIG_OF_LIBFDT diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h index 651c4c4935..68da23e8b7 100644 --- a/include/configs/tegra-common-post.h +++ b/include/configs/tegra-common-post.h @@ -19,9 +19,7 @@ #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* 4MB */ #endif -#ifndef CONFIG_ARM64 #define CONFIG_SYS_NONCACHED_MEMORY (1 << 20) /* 1 MiB */ -#endif #ifndef CONFIG_SPL_BUILD #define BOOT_TARGET_DEVICES(func) \ diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h index 02b0e6351f..0ab69e665a 100644 --- a/include/configs/tricorder.h +++ b/include/configs/tricorder.h @@ -17,6 +17,7 @@ #define __CONFIG_H /* High Level Configuration Options */ +#define CONFIG_SYS_THUMB_BUILD #define CONFIG_OMAP /* in a TI OMAP core */ #define CONFIG_OMAP_COMMON /* Common ARM Erratas */ |
