diff options
| -rw-r--r-- | MAINTAINERS | 1 | ||||
| -rwxr-xr-x | MAKEALL | 1 | ||||
| -rw-r--r-- | Makefile | 5 | ||||
| -rw-r--r-- | board/bf548-ezkit/.gitignore | 1 | ||||
| -rw-r--r-- | board/bf548-ezkit/Makefile | 58 | ||||
| -rw-r--r-- | board/bf548-ezkit/bf548-ezkit.c | 79 | ||||
| -rw-r--r-- | board/bf548-ezkit/config.mk | 37 | ||||
| -rw-r--r-- | board/bf548-ezkit/u-boot.lds.S | 124 | ||||
| -rw-r--r-- | board/bf548-ezkit/video.c | 327 | ||||
| -rw-r--r-- | include/configs/bf548-ezkit.h | 211 |
10 files changed, 842 insertions, 2 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 25b28d6a23..47b604962e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -857,6 +857,7 @@ Blackfin Team <u-boot-devel@blackfin.uclinux.org> BF533-EZKIT BF533 BF533-STAMP BF533 BF537-STAMP BF537 + BF548-EZKIT BF548 BF561-EZKIT BF561 ######################################################################### @@ -791,6 +791,7 @@ LIST_blackfin=" \ bf533-ezkit \ bf533-stamp \ bf537-stamp \ + bf548-ezkit \ bf561-ezkit \ " @@ -3336,7 +3336,7 @@ suzaku_config: unconfig #======================================================================== # Analog Devices boards -BFIN_BOARDS = bf533-ezkit bf533-stamp bf537-stamp bf561-ezkit +BFIN_BOARDS = bf533-ezkit bf533-stamp bf537-stamp bf548-ezkit bf561-ezkit $(BFIN_BOARDS:%=%_config) : unconfig @$(MKCONFIG) $(@:_config=) blackfin blackfin $(@:_config=) @@ -3510,7 +3510,8 @@ clean: $(obj)board/netstar/{eeprom,crcek,crcit,*.srec,*.bin} \ $(obj)board/trab/trab_fkt $(obj)board/voiceblue/eeprom \ $(obj)board/armltd/{integratorap,integratorcp}/u-boot.lds \ - $(obj)board/{bf533-ezkit,bf533-stamp,bf537-stamp,bf561-ezkit}/u-boot.lds \ + $(obj)board/bf5{33,48,61}-ezkit/u-boot.lds \ + $(obj)board/bf5{33,37}-stamp/u-boot.lds \ $(obj)cpu/blackfin/bootrom-asm-offsets.[chs] @rm -f $(obj)include/bmp_logo.h @rm -f $(obj)nand_spl/{u-boot-spl,u-boot-spl.map,System.map} diff --git a/board/bf548-ezkit/.gitignore b/board/bf548-ezkit/.gitignore new file mode 100644 index 0000000000..945f324549 --- /dev/null +++ b/board/bf548-ezkit/.gitignore @@ -0,0 +1 @@ +/u-boot.lds diff --git a/board/bf548-ezkit/Makefile b/board/bf548-ezkit/Makefile new file mode 100644 index 0000000000..c2b98ec74a --- /dev/null +++ b/board/bf548-ezkit/Makefile @@ -0,0 +1,58 @@ +# +# U-boot - Makefile +# +# Copyright (c) 2005-2008 Analog Device Inc. +# +# (C) Copyright 2000-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y := $(BOARD).o +COBJS-$(CONFIG_VIDEO) += video.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) $(obj)u-boot.lds + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +$(obj)u-boot.lds: u-boot.lds.S + $(CPP) $(CPPFLAGS) -D__ASSEMBLY__ -P $^ > $@ + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/bf548-ezkit/bf548-ezkit.c b/board/bf548-ezkit/bf548-ezkit.c new file mode 100644 index 0000000000..74f93ba27d --- /dev/null +++ b/board/bf548-ezkit/bf548-ezkit.c @@ -0,0 +1,79 @@ +/* + * U-boot - main board file + * + * Copyright (c) 2005-2008 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <common.h> +#include <config.h> +#include <command.h> +#include <asm/blackfin.h> + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + printf("Board: ADI BF548 EZ-Kit board\n"); + printf(" Support: http://blackfin.uclinux.org/\n"); + return 0; +} + +phys_size_t initdram(int board_type) +{ + gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE; + gd->bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE; + return gd->bd->bi_memsize; +} + +int board_early_init_f(void) +{ + /* Port H: PH8 - PH13 == A4 - A9 + * address lines of the parallel asynchronous memory interface + */ + + /************************************************ + * configure GPIO * + * set port H function enable register * + * configure PH8-PH13 as peripheral (not GPIO) * + *************************************************/ + bfin_write_PORTH_FER(0x3F03); + + /************************************************ + * set port H MUX to configure PH8-PH13 * + * 1st Function (MUX = 00) (bits 16-27 == 0) * + * Set to address signals A4-A9 * + *************************************************/ + bfin_write_PORTH_MUX(0); + + /************************************************ + * set port H direction register * + * enable PH8-PH13 as outputs * + *************************************************/ + bfin_write_PORTH_DIR_SET(0x3F00); + + /* Port I: PI0 - PH14 == A10 - A24 + * address lines of the parallel asynchronous memory interface + */ + + /************************************************ + * set port I function enable register * + * configure PI0-PI14 as peripheral (not GPIO) * + *************************************************/ + bfin_write_PORTI_FER(0x7fff); + + /************************************************** + * set PORT I MUX to configure PI14-PI0 as * + * 1st Function (MUX=00) - address signals A10-A24 * + ***************************************************/ + bfin_write_PORTI_MUX(0); + + /**************************************** + * set PORT I direction register * + * enable PI0 - PI14 as outputs * + *****************************************/ + bfin_write_PORTI_DIR_SET(0x7fff); + + return 0; +} diff --git a/board/bf548-ezkit/config.mk b/board/bf548-ezkit/config.mk new file mode 100644 index 0000000000..8b471f60de --- /dev/null +++ b/board/bf548-ezkit/config.mk @@ -0,0 +1,37 @@ +# +# Copyright (c) 2005-2008 Analog Device Inc. +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# This is not actually used for Blackfin boards so do not change it +#TEXT_BASE = do-not-use-me + +LDSCRIPT = $(obj)board/$(BOARDDIR)/u-boot.lds + +# Set some default LDR flags based on boot mode. +LDR_FLAGS-BFIN_BOOT_PARA := --dma 6 +LDR_FLAGS-BFIN_BOOT_FIFO := --dma 1 +LDR_FLAGS-BFIN_BOOT_SPI_MASTER := --dma 1 +LDR_FLAGS-BFIN_BOOT_UART := --dma 1 +LDR_FLAGS-BFIN_BOOT_NAND := --dma 6 +LDR_FLAGS += $(LDR_FLAGS-$(CONFIG_BFIN_BOOT_MODE)) diff --git a/board/bf548-ezkit/u-boot.lds.S b/board/bf548-ezkit/u-boot.lds.S new file mode 100644 index 0000000000..3e8be358da --- /dev/null +++ b/board/bf548-ezkit/u-boot.lds.S @@ -0,0 +1,124 @@ +/* + * U-boot - u-boot.lds.S + * + * Copyright (c) 2005-2008 Analog Device Inc. + * + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <asm/blackfin.h> +#undef ALIGN +#undef ENTRY +#undef bfin + +/* If we don't actually load anything into L1 data, this will avoid + * a syntax error. If we do actually load something into L1 data, + * we'll get a linker memory load error (which is what we'd want). + * This is here in the first place so we can quickly test building + * for different CPU's which may lack non-cache L1 data. + */ +#ifndef L1_DATA_B_SRAM +# define L1_DATA_B_SRAM CONFIG_SYS_MONITOR_BASE +# define L1_DATA_B_SRAM_SIZE 0 +#endif + +OUTPUT_ARCH(bfin) + +MEMORY +{ + ram : ORIGIN = CONFIG_SYS_MONITOR_BASE, LENGTH = CONFIG_SYS_MONITOR_LEN + l1_code : ORIGIN = L1_INST_SRAM, LENGTH = L1_INST_SRAM_SIZE + l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE +} + +ENTRY(_start) +SECTIONS +{ + .text : + { + cpu/blackfin/start.o (.text .text.*) + __initcode_start = .; + cpu/blackfin/initcode.o (.text .text.*) + __initcode_end = .; + *(.text .text.*) + } >ram + + .rodata : + { + . = ALIGN(4); + *(.rodata .rodata.*) + *(.rodata1) + *(.eh_frame) + . = ALIGN(4); + } >ram + + .data : + { + . = ALIGN(256); + *(.data .data.*) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } >ram + + .u_boot_cmd : + { + ___u_boot_cmd_start = .; + *(.u_boot_cmd) + ___u_boot_cmd_end = .; + } >ram + + .text_l1 : + { + . = ALIGN(4); + __stext_l1 = .; + *(.l1.text) + . = ALIGN(4); + __etext_l1 = .; + } >l1_code AT>ram + __stext_l1_lma = LOADADDR(.text_l1); + + .data_l1 : + { + . = ALIGN(4); + __sdata_l1 = .; + *(.l1.data) + *(.l1.bss) + . = ALIGN(4); + __edata_l1 = .; + } >l1_data AT>ram + __sdata_l1_lma = LOADADDR(.data_l1); + + .bss : + { + . = ALIGN(4); + __bss_start = .; + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss .bss.*) + *(COMMON) + __bss_end = .; + } >ram +} diff --git a/board/bf548-ezkit/video.c b/board/bf548-ezkit/video.c new file mode 100644 index 0000000000..a6f52bdfef --- /dev/null +++ b/board/bf548-ezkit/video.c @@ -0,0 +1,327 @@ +/* + * video.c - run splash screen on lcd + * + * Copyright (c) 2007-2008 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <stdarg.h> +#include <common.h> +#include <config.h> +#include <malloc.h> +#include <asm/blackfin.h> +#include <asm/mach-common/bits/dma.h> +#include <i2c.h> +#include <linux/types.h> +#include <devices.h> + +int gunzip(void *, int, unsigned char *, unsigned long *); + +#define DMA_SIZE16 2 + +#include <asm/mach-common/bits/eppi.h> + +#include <asm/bfin_logo_230x230.h> + +#define LCD_X_RES 480 /*Horizontal Resolution */ +#define LCD_Y_RES 272 /* Vertical Resolution */ + +#define LCD_BPP 24 /* Bit Per Pixel */ +#define LCD_PIXEL_SIZE (LCD_BPP / 8) +#define DMA_BUS_SIZE 32 +#define ACTIVE_VIDEO_MEM_OFFSET 0 + +/* -- Horizontal synchronizing -- + * + * Timing characteristics taken from the SHARP LQ043T1DG01 datasheet + * (LCY-W-06602A Page 9 of 22) + * + * Clock Frequency 1/Tc Min 7.83 Typ 9.00 Max 9.26 MHz + * + * Period TH - 525 - Clock + * Pulse width THp - 41 - Clock + * Horizontal period THd - 480 - Clock + * Back porch THb - 2 - Clock + * Front porch THf - 2 - Clock + * + * -- Vertical synchronizing -- + * Period TV - 286 - Line + * Pulse width TVp - 10 - Line + * Vertical period TVd - 272 - Line + * Back porch TVb - 2 - Line + * Front porch TVf - 2 - Line + */ + +#define LCD_CLK (8*1000*1000) /* 8MHz */ + +/* # active data to transfer after Horizontal Delay clock */ +#define EPPI_HCOUNT LCD_X_RES + +/* # active lines to transfer after Vertical Delay clock */ +#define EPPI_VCOUNT LCD_Y_RES + +/* Samples per Line = 480 (active data) + 45 (padding) */ +#define EPPI_LINE 525 + +/* Lines per Frame = 272 (active data) + 14 (padding) */ +#define EPPI_FRAME 286 + +/* FS1 (Hsync) Width (Typical)*/ +#define EPPI_FS1W_HBL 41 + +/* FS1 (Hsync) Period (Typical) */ +#define EPPI_FS1P_AVPL EPPI_LINE + +/* Horizontal Delay clock after assertion of Hsync (Typical) */ +#define EPPI_HDELAY 43 + +/* FS2 (Vsync) Width = FS1 (Hsync) Period * 10 */ +#define EPPI_FS2W_LVB (EPPI_LINE * 10) + + /* FS2 (Vsync) Period = FS1 (Hsync) Period * Lines per Frame */ +#define EPPI_FS2P_LAVF (EPPI_LINE * EPPI_FRAME) + +/* Vertical Delay after assertion of Vsync (2 Lines) */ +#define EPPI_VDELAY 12 + +#define EPPI_CLIP 0xFF00FF00 + +/* EPPI Control register configuration value for RGB out + * - EPPI as Output + * GP 2 frame sync mode, + * Internal Clock generation disabled, Internal FS generation enabled, + * Receives samples on EPPI_CLK raising edge, Transmits samples on EPPI_CLK falling edge, + * FS1 & FS2 are active high, + * DLEN = 6 (24 bits for RGB888 out) or 5 (18 bits for RGB666 out) + * DMA Unpacking disabled when RGB Formating is enabled, otherwise DMA unpacking enabled + * Swapping Enabled, + * One (DMA) Channel Mode, + * RGB Formatting Enabled for RGB666 output, disabled for RGB888 output + * Regular watermark - when FIFO is 100% full, + * Urgent watermark - when FIFO is 75% full + */ + +#define EPPI_CONTROL (0x20136E2E) + +static inline u16 get_eppi_clkdiv(u32 target_ppi_clk) +{ + u32 sclk = get_sclk(); + + /* EPPI_CLK = (SCLK) / (2 * (EPPI_CLKDIV[15:0] + 1)) */ + + return (((sclk / target_ppi_clk) / 2) - 1); +} + +void Init_PPI(void) +{ + u16 eppi_clkdiv = get_eppi_clkdiv(LCD_CLK); + + bfin_write_EPPI0_FS1W_HBL(EPPI_FS1W_HBL); + bfin_write_EPPI0_FS1P_AVPL(EPPI_FS1P_AVPL); + bfin_write_EPPI0_FS2W_LVB(EPPI_FS2W_LVB); + bfin_write_EPPI0_FS2P_LAVF(EPPI_FS2P_LAVF); + bfin_write_EPPI0_CLIP(EPPI_CLIP); + + bfin_write_EPPI0_FRAME(EPPI_FRAME); + bfin_write_EPPI0_LINE(EPPI_LINE); + + bfin_write_EPPI0_HCOUNT(EPPI_HCOUNT); + bfin_write_EPPI0_HDELAY(EPPI_HDELAY); + bfin_write_EPPI0_VCOUNT(EPPI_VCOUNT); + bfin_write_EPPI0_VDELAY(EPPI_VDELAY); + + bfin_write_EPPI0_CLKDIV(eppi_clkdiv); + +/* + * DLEN = 6 (24 bits for RGB888 out) or 5 (18 bits for RGB666 out) + * RGB Formatting Enabled for RGB666 output, disabled for RGB888 output + */ +#if defined(CONFIG_VIDEO_RGB666) + bfin_write_EPPI0_CONTROL((EPPI_CONTROL & ~DLENGTH) | DLEN_18 | + RGB_FMT_EN); +#else + bfin_write_EPPI0_CONTROL(((EPPI_CONTROL & ~DLENGTH) | DLEN_24) & + ~RGB_FMT_EN); +#endif + +} + +#define DEB2_URGENT 0x2000 /* DEB2 Urgent */ + +void Init_DMA(void *dst) +{ + +#if defined(CONFIG_DEB_DMA_URGENT) + *pEBIU_DDRQUE |= DEB2_URGENT; +#endif + + *pDMA12_START_ADDR = dst; + + /* X count */ + *pDMA12_X_COUNT = (LCD_X_RES * LCD_BPP) / DMA_BUS_SIZE; + *pDMA12_X_MODIFY = DMA_BUS_SIZE / 8; + + /* Y count */ + *pDMA12_Y_COUNT = LCD_Y_RES; + *pDMA12_Y_MODIFY = DMA_BUS_SIZE / 8; + + /* DMA Config */ + *pDMA12_CONFIG = + WDSIZE_32 | /* 32 bit DMA */ + DMA2D | /* 2D DMA */ + FLOW_AUTO; /* autobuffer mode */ +} + +void Init_Ports(void) +{ + *pPORTF_MUX = 0x00000000; + *pPORTF_FER |= 0xFFFF; /* PPI0..15 */ + + *pPORTG_MUX &= ~(PORT_x_MUX_0_MASK | PORT_x_MUX_1_MASK | PORT_x_MUX_2_MASK | PORT_x_MUX_3_MASK | PORT_x_MUX_4_MASK); + *pPORTG_FER |= PG0 | PG1 | PG2 | PG3 | PG4; /* CLK, FS1, FS2, PPI16..17 */ + +#if !defined(CONFIG_VIDEO_RGB666) + *pPORTD_MUX &= ~(PORT_x_MUX_0_MASK | PORT_x_MUX_1_MASK | PORT_x_MUX_2_MASK | PORT_x_MUX_3_MASK | PORT_x_MUX_4_MASK | PORT_x_MUX_5_MASK); + *pPORTD_MUX |= (PORT_x_MUX_0_FUNC_4 | PORT_x_MUX_1_FUNC_4 | PORT_x_MUX_2_FUNC_4 | PORT_x_MUX_3_FUNC_4 | PORT_x_MUX_4_FUNC_4 | PORT_x_MUX_5_FUNC_4); + *pPORTD_FER |= PD0 | PD1 | PD2 | PD3 | PD4 | PD5; /* PPI18..23 */ +#endif + + *pPORTE_FER &= ~PE3; /* DISP */ + *pPORTE_DIR_SET = PE3; + *pPORTE_SET = PE3; + +} + +void EnableDMA(void) +{ + *pDMA12_CONFIG |= DMAEN; +} + +void DisableDMA(void) +{ + *pDMA12_CONFIG &= ~DMAEN; +} + +/* enable and disable PPI functions */ +void EnablePPI(void) +{ + bfin_write_EPPI0_CONTROL(bfin_read_EPPI0_CONTROL() | EPPI_EN); +} + +void DisablePPI(void) +{ + bfin_write_EPPI0_CONTROL(bfin_read_EPPI0_CONTROL() & ~EPPI_EN); +} + +int video_init(void *dst) +{ + Init_Ports(); + Init_DMA(dst); + EnableDMA(); + Init_PPI(); + EnablePPI(); + + return 0; +} + +static void dma_bitblit(void *dst, fastimage_t *logo, int x, int y) +{ + if (dcache_status()) + blackfin_dcache_flush_range(logo->data, logo->data + logo->size); + + bfin_write_MDMA_D0_IRQ_STATUS(DMA_DONE | DMA_ERR); + + /* Setup destination start address */ + bfin_write_MDMA_D0_START_ADDR(dst + ((x & -2) * LCD_PIXEL_SIZE) + + (y * LCD_X_RES * LCD_PIXEL_SIZE)); + /* Setup destination xcount */ + bfin_write_MDMA_D0_X_COUNT(logo->width * LCD_PIXEL_SIZE / DMA_SIZE16); + /* Setup destination xmodify */ + bfin_write_MDMA_D0_X_MODIFY(DMA_SIZE16); + + /* Setup destination ycount */ + bfin_write_MDMA_D0_Y_COUNT(logo->height); + /* Setup destination ymodify */ + bfin_write_MDMA_D0_Y_MODIFY((LCD_X_RES - logo->width) * LCD_PIXEL_SIZE + DMA_SIZE16); + + + /* Setup Source start address */ + bfin_write_MDMA_S0_START_ADDR(logo->data); + /* Setup Source xcount */ + bfin_write_MDMA_S0_X_COUNT(logo->width * LCD_PIXEL_SIZE / DMA_SIZE16); + /* Setup Source xmodify */ + bfin_write_MDMA_S0_X_MODIFY(DMA_SIZE16); + + /* Setup Source ycount */ + bfin_write_MDMA_S0_Y_COUNT(logo->height); + /* Setup Source ymodify */ + bfin_write_MDMA_S0_Y_MODIFY(DMA_SIZE16); + + + /* Enable source DMA */ + bfin_write_MDMA_S0_CONFIG(DMAEN | WDSIZE_16 | DMA2D); + SSYNC(); + bfin_write_MDMA_D0_CONFIG(WNR | DMAEN | WDSIZE_16 | DMA2D); + + while (bfin_read_MDMA_D0_IRQ_STATUS() & DMA_RUN); + + bfin_write_MDMA_S0_IRQ_STATUS(bfin_read_MDMA_S0_IRQ_STATUS() | DMA_DONE | DMA_ERR); + bfin_write_MDMA_D0_IRQ_STATUS(bfin_read_MDMA_D0_IRQ_STATUS() | DMA_DONE | DMA_ERR); + +} + +void video_putc(const char c) +{ +} + +void video_puts(const char *s) +{ +} + +int drv_video_init(void) +{ + int error, devices = 1; + device_t videodev; + + u8 *dst; + u32 fbmem_size = LCD_X_RES * LCD_Y_RES * LCD_PIXEL_SIZE + ACTIVE_VIDEO_MEM_OFFSET; + + dst = malloc(fbmem_size); + + if (dst == NULL) { + printf("Failed to alloc FB memory\n"); + return -1; + } + +#ifdef EASYLOGO_ENABLE_GZIP + unsigned char *data = EASYLOGO_DECOMP_BUFFER; + unsigned long src_len = EASYLOGO_ENABLE_GZIP; + if (gunzip(data, bfin_logo.size, bfin_logo.data, &src_len)) { + puts("Failed to decompress logo\n"); + free(dst); + return -1; + } + bfin_logo.data = data; +#endif + + memset(dst + ACTIVE_VIDEO_MEM_OFFSET, bfin_logo.data[0], fbmem_size - ACTIVE_VIDEO_MEM_OFFSET); + + dma_bitblit(dst + ACTIVE_VIDEO_MEM_OFFSET, &bfin_logo, + (LCD_X_RES - bfin_logo.width) / 2, + (LCD_Y_RES - bfin_logo.height) / 2); + + video_init(dst); /* Video initialization */ + + memset(&videodev, 0, sizeof(videodev)); + + strcpy(videodev.name, "video"); + videodev.ext = DEV_EXT_VIDEO; /* Video extensions */ + videodev.flags = DEV_FLAGS_SYSTEM; /* No Output */ + videodev.putc = video_putc; /* 'putc' function */ + videodev.puts = video_puts; /* 'puts' function */ + + error = device_register(&videodev); + + return (error == 0) ? devices : error; +} diff --git a/include/configs/bf548-ezkit.h b/include/configs/bf548-ezkit.h new file mode 100644 index 0000000000..ae9fb36745 --- /dev/null +++ b/include/configs/bf548-ezkit.h @@ -0,0 +1,211 @@ +/* + * U-boot - Configuration file for BF548 STAMP board + */ + +#ifndef __CONFIG_BF548_EZKIT_H__ +#define __CONFIG_BF548_EZKIT_H__ + +#include <asm/blackfin-config-pre.h> + + +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf548-0.0 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA + + +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 25000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 21 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 4 + + +/* + * Memory Settings + */ +#define CONFIG_MEM_ADD_WDTH 10 +#define CONFIG_MEM_SIZE 64 + +#define CONFIG_EBIU_DDRCTL0_VAL 0x218A83FE +#define CONFIG_EBIU_DDRCTL1_VAL 0x20022222 +#define CONFIG_EBIU_DDRCTL2_VAL 0x00000021 + +/* Default EZ-Kit bank mapping: + * Async Bank 0 - 32MB Burst Flash + * Async Bank 1 - Ethernet + * Async Bank 2 - Nothing + * Async Bank 3 - Nothing + */ +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 +#define CONFIG_EBIU_FCTL_VAL (BCLK_4) +#define CONFIG_EBIU_MODE_VAL (B0MODE_FLASH) + +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#define CONFIG_SYS_MALLOC_LEN (768 * 1024) + + +/* + * Network Settings + */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC911X 1 +#define CONFIG_DRIVER_SMC911X_BASE 0x24000000 +#define CONFIG_DRIVER_SMC911X_16_BIT +#define CONFIG_HOSTNAME bf548-ezkit +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ + + +/* + * Flash Settings + */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 259 + + +/* + * SPI Settings + */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_HZ 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO + + +/* + * Env Storage Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define ENV_IS_EMBEDDED_CUSTOM +#elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SIZE 0x20000 +#else +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR 0x20002000 +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE (128 * 1024) +#define ENV_IS_EMBEDDED_CUSTOM +#endif + + +/* + * NAND Settings + */ +#define CONFIG_BFIN_NFC_CTL_VAL 0x0033 +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) +# define CONFIG_BFIN_NFC_BOOTROM_ECC +#endif +#define CONFIG_DRIVER_NAND_BFIN +#define CONFIG_SYS_NAND_BASE 0 /* not actually used */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_CMD_NAND + + +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C 1 +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0 + + +/* + * SATA + */ +#if !defined(__ADSPBF544__) +#define CONFIG_LIBATA +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_LBA48 +#define CONFIG_PATA_BFIN +#define CONFIG_BFIN_ATAPI_BASE_ADDR 0xFFC03800 +#define CONFIG_BFIN_ATA_MODE XFER_PIO_4 +#endif + + +/* + * SDH Settings + */ +#if !defined(__ADSPBF544__) +#define CONFIG_MMC +#define CONFIG_BFIN_SDH +#endif + + +/* + * USB Settings + */ +#if !defined(__ADSPBF544__) +#define CONFIG_USB +#define CONFIG_MUSB_HCD +#define CONFIG_USB_BLACKFIN +#define CONFIG_USB_STORAGE +#define CONFIG_MUSB_TIMEOUT 100000 +#endif + + +/* + * Misc Settings + */ +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 1 + +#ifndef __ADSPBF542__ +/* Don't waste time transferring a logo over the UART */ +# if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART) +# define CONFIG_VIDEO +# endif +# define CONFIG_DEB_DMA_URGENT +#endif + +/* Define if want to do post memory test */ +#undef CONFIG_POST +#ifdef CONFIG_POST +#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ +#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ +#endif + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> + +#include <asm/blackfin-config-post.h> + +#endif |
