diff options
35 files changed, 1047 insertions, 261 deletions
@@ -3026,6 +3026,24 @@ to save the current settings. environment area within the total memory of your DataFlash placed at the specified address. +- CONFIG_ENV_IS_IN_REMOTE: + + Define this if you have a remote memory space which you + want to use for the local device's environment. + + - CONFIG_ENV_ADDR: + - CONFIG_ENV_SIZE: + + These two #defines specify the address and size of the + environment area within the remote memory space. The + local device can get the environment from remote memory + space by SRIO or other links. + +BE CAREFUL! For some special cases, the local device can not use +"saveenv" command. For example, the local device will get the +environment stored in a remote NOR flash by SRIO link, but it can +not erase, write this NOR flash by SRIO interface. + - CONFIG_ENV_IS_IN_NAND: Define this if you have a NAND device which you want to use @@ -3462,6 +3480,12 @@ within that device. Specifies that QE/FMAN firmware is located on the primary SPI device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device. +- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE + Specifies that QE/FMAN firmware is located in the remote (master) + memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which + can be mapped from slave TLB->slave LAW->slave SRIO outbound window + ->master inbound window->master LAW->the ucode address in master's + NOR flash. Building the Software: ====================== diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index 2e4a06c35a..2cd5db7c59 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -37,6 +37,7 @@ #include <asm/mmu.h> #include <asm/fsl_law.h> #include <asm/fsl_serdes.h> +#include <asm/fsl_srio.h> #include <linux/compiler.h> #include "mp.h" #ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND @@ -48,8 +49,6 @@ DECLARE_GLOBAL_DATA_PTR; -extern void srio_init(void); - #ifdef CONFIG_QE extern qe_iop_conf_t qe_iop_conf_tab[]; extern void qe_config_iopin(u8 port, u8 pin, int dir, @@ -443,6 +442,12 @@ skip_l2: #ifdef CONFIG_SYS_SRIO srio_init(); +#ifdef CONFIG_SRIOBOOT_MASTER + srio_boot_master(); +#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF + srio_boot_master_release_slave(); +#endif +#endif #endif #if defined(CONFIG_MP) diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S index 4d37d6e863..8e99ef6c68 100644 --- a/arch/powerpc/cpu/mpc85xx/start.S +++ b/arch/powerpc/cpu/mpc85xx/start.S @@ -1,5 +1,5 @@ /* - * Copyright 2004, 2007-2011 Freescale Semiconductor, Inc. + * Copyright 2004, 2007-2012 Freescale Semiconductor, Inc. * Copyright (C) 2003 Motorola,Inc. * * See file CREDITS for list of people who contributed to this @@ -179,41 +179,50 @@ l2_disabled: andi. r1,r3,L1CSR0_DCE@l beq 2b +/* + * Ne need to setup interrupt vector for NAND SPL + * because NAND SPL never compiles it. + */ +#if !defined(CONFIG_NAND_SPL) /* Setup interrupt vectors */ lis r1,CONFIG_SYS_MONITOR_BASE@h mtspr IVPR,r1 - li r1,0x0100 - mtspr IVOR0,r1 /* 0: Critical input */ - li r1,0x0200 - mtspr IVOR1,r1 /* 1: Machine check */ - li r1,0x0300 - mtspr IVOR2,r1 /* 2: Data storage */ - li r1,0x0400 - mtspr IVOR3,r1 /* 3: Instruction storage */ - li r1,0x0500 - mtspr IVOR4,r1 /* 4: External interrupt */ - li r1,0x0600 - mtspr IVOR5,r1 /* 5: Alignment */ - li r1,0x0700 - mtspr IVOR6,r1 /* 6: Program check */ - li r1,0x0800 - mtspr IVOR7,r1 /* 7: floating point unavailable */ - li r1,0x0900 - mtspr IVOR8,r1 /* 8: System call */ + lis r3,(CONFIG_SYS_MONITOR_BASE & 0xffff)@h + ori r3,r3,(CONFIG_SYS_MONITOR_BASE & 0xffff)@l + + addi r4,r3,CriticalInput - _start + _START_OFFSET + mtspr IVOR0,r4 /* 0: Critical input */ + addi r4,r3,MachineCheck - _start + _START_OFFSET + mtspr IVOR1,r4 /* 1: Machine check */ + addi r4,r3,DataStorage - _start + _START_OFFSET + mtspr IVOR2,r4 /* 2: Data storage */ + addi r4,r3,InstStorage - _start + _START_OFFSET + mtspr IVOR3,r4 /* 3: Instruction storage */ + addi r4,r3,ExtInterrupt - _start + _START_OFFSET + mtspr IVOR4,r4 /* 4: External interrupt */ + addi r4,r3,Alignment - _start + _START_OFFSET + mtspr IVOR5,r4 /* 5: Alignment */ + addi r4,r3,ProgramCheck - _start + _START_OFFSET + mtspr IVOR6,r4 /* 6: Program check */ + addi r4,r3,FPUnavailable - _start + _START_OFFSET + mtspr IVOR7,r4 /* 7: floating point unavailable */ + addi r4,r3,SystemCall - _start + _START_OFFSET + mtspr IVOR8,r4 /* 8: System call */ /* 9: Auxiliary processor unavailable(unsupported) */ - li r1,0x0a00 - mtspr IVOR10,r1 /* 10: Decrementer */ - li r1,0x0b00 - mtspr IVOR11,r1 /* 11: Interval timer */ - li r1,0x0c00 - mtspr IVOR12,r1 /* 12: Watchdog timer */ - li r1,0x0d00 - mtspr IVOR13,r1 /* 13: Data TLB error */ - li r1,0x0e00 - mtspr IVOR14,r1 /* 14: Instruction TLB error */ - li r1,0x0f00 - mtspr IVOR15,r1 /* 15: Debug */ + addi r4,r3,Decrementer - _start + _START_OFFSET + mtspr IVOR10,r4 /* 10: Decrementer */ + addi r4,r3,IntervalTimer - _start + _START_OFFSET + mtspr IVOR11,r4 /* 11: Interval timer */ + addi r4,r3,WatchdogTimer - _start + _START_OFFSET + mtspr IVOR12,r4 /* 12: Watchdog timer */ + addi r4,r3,DataTLBError - _start + _START_OFFSET + mtspr IVOR13,r4 /* 13: Data TLB error */ + addi r4,r3,InstructionTLBError - _start + _START_OFFSET + mtspr IVOR14,r4 /* 14: Instruction TLB error */ + addi r4,r3,DebugBreakpoint - _start + _START_OFFSET + mtspr IVOR15,r4 /* 15: Debug */ +#endif /* Clear and set up some registers. */ li r0,0x0000 @@ -434,13 +443,15 @@ create_ccsr_new_tlb: ori r2, r2, FSL_BOOKE_MAS2(CONFIG_SYS_CCSRBAR, (MAS2_I|MAS2_G))@l lis r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@h ori r3, r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@l +#ifdef CONFIG_ENABLE_36BIT_PHYS lis r7, CONFIG_SYS_CCSRBAR_PHYS_HIGH@h ori r7, r7, CONFIG_SYS_CCSRBAR_PHYS_HIGH@l + mtspr MAS7, r7 +#endif mtspr MAS0, r0 mtspr MAS1, r1 mtspr MAS2, r2 mtspr MAS3, r3 - mtspr MAS7, r7 isync msync tlbwe @@ -456,12 +467,14 @@ create_ccsr_old_tlb: ori r2, r2, FSL_BOOKE_MAS2(CONFIG_SYS_CCSRBAR + 0x1000, (MAS2_I|MAS2_G))@l lis r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_DEFAULT, 0, (MAS3_SW|MAS3_SR))@h ori r3, r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_DEFAULT, 0, (MAS3_SW|MAS3_SR))@l +#ifdef CONFIG_ENABLE_36BIT_PHYS li r7, 0 /* The default CCSR address is always a 32-bit number */ + mtspr MAS7, r7 +#endif mtspr MAS0, r0 /* MAS1 is the same as above */ mtspr MAS2, r2 mtspr MAS3, r3 - mtspr MAS7, r7 isync msync tlbwe @@ -1490,6 +1503,39 @@ trap_init: cmplw 0,r7,r8 blt 2b + /* Update IVORs as per relocated vector table address */ + li r7,0x0100 + mtspr IVOR0,r7 /* 0: Critical input */ + li r7,0x0200 + mtspr IVOR1,r7 /* 1: Machine check */ + li r7,0x0300 + mtspr IVOR2,r7 /* 2: Data storage */ + li r7,0x0400 + mtspr IVOR3,r7 /* 3: Instruction storage */ + li r7,0x0500 + mtspr IVOR4,r7 /* 4: External interrupt */ + li r7,0x0600 + mtspr IVOR5,r7 /* 5: Alignment */ + li r7,0x0700 + mtspr IVOR6,r7 /* 6: Program check */ + li r7,0x0800 + mtspr IVOR7,r7 /* 7: floating point unavailable */ + li r7,0x0900 + mtspr IVOR8,r7 /* 8: System call */ + /* 9: Auxiliary processor unavailable(unsupported) */ + li r7,0x0a00 + mtspr IVOR10,r7 /* 10: Decrementer */ + li r7,0x0b00 + mtspr IVOR11,r7 /* 11: Interval timer */ + li r7,0x0c00 + mtspr IVOR12,r7 /* 12: Watchdog timer */ + li r7,0x0d00 + mtspr IVOR13,r7 /* 13: Data TLB error */ + li r7,0x0e00 + mtspr IVOR14,r7 /* 14: Instruction TLB error */ + li r7,0x0f00 + mtspr IVOR15,r7 /* 15: Debug */ + lis r7,0x0 mtspr IVPR,r7 diff --git a/arch/powerpc/cpu/mpc85xx/u-boot-nand.lds b/arch/powerpc/cpu/mpc85xx/u-boot-nand.lds index 04bc73170a..b1a1dac16f 100644 --- a/arch/powerpc/cpu/mpc85xx/u-boot-nand.lds +++ b/arch/powerpc/cpu/mpc85xx/u-boot-nand.lds @@ -1,5 +1,5 @@ /* - * Copyright 2009 Freescale Semiconductor, Inc. + * Copyright 2009-2012 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -87,7 +87,7 @@ SECTIONS .bootpg ADDR(.text) - 0x1000 : { - arch/powerpc/cpu/mpc85xx/start.o KEEP(*(.bootpg)) + KEEP(arch/powerpc/cpu/mpc85xx/start.o (.bootpg)) } :text = 0xffff . = ADDR(.text) + 0x80000; diff --git a/arch/powerpc/cpu/mpc8xxx/srio.c b/arch/powerpc/cpu/mpc8xxx/srio.c index e46d328067..c7f394972b 100644 --- a/arch/powerpc/cpu/mpc8xxx/srio.c +++ b/arch/powerpc/cpu/mpc8xxx/srio.c @@ -21,6 +21,16 @@ #include <config.h> #include <asm/fsl_law.h> #include <asm/fsl_serdes.h> +#include <asm/fsl_srio.h> + +#define SRIO_PORT_ACCEPT_ALL 0x10000001 +#define SRIO_IB_ATMU_AR 0x80f55000 +#define SRIO_OB_ATMU_AR_MAINT 0x80077000 +#define SRIO_OB_ATMU_AR_RW 0x80045000 +#define SRIO_LCSBA1CSR_OFFSET 0x5c +#define SRIO_MAINT_WIN_SIZE 0x1000000 /* 16M */ +#define SRIO_RW_WIN_SIZE 0x100000 /* 1M */ +#define SRIO_LCSBA1CSR 0x60000000 #if defined(CONFIG_FSL_CORENET) #define _DEVDISR_SRIO1 FSL_CORENET_DEVDISR_SRIO1 @@ -84,3 +94,203 @@ void srio_init(void) setbits_be32(&gur->devdisr, _DEVDISR_RMU); } } + +#ifdef CONFIG_SRIOBOOT_MASTER +void srio_boot_master(void) +{ + struct ccsr_rio *srio = (void *)CONFIG_SYS_FSL_SRIO_ADDR; + + /* set port accept-all */ + out_be32((void *)&srio->impl.port[CONFIG_SRIOBOOT_MASTER_PORT].ptaacr, + SRIO_PORT_ACCEPT_ALL); + + debug("SRIOBOOT - MASTER: Master port [ %d ] for srio boot.\n", + CONFIG_SRIOBOOT_MASTER_PORT); + /* configure inbound window for slave's u-boot image */ + debug("SRIOBOOT - MASTER: Inbound window for slave's image; " + "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n", + (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1, + (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1, + CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwtar, + CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1 >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwbar, + CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1 >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[0].riwar, + SRIO_IB_ATMU_AR + | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE)); + + /* configure inbound window for slave's u-boot image */ + debug("SRIOBOOT - MASTER: Inbound window for slave's image; " + "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n", + (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2, + (u64)CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2, + CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwtar, + CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2 >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwbar, + CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2 >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[1].riwar, + SRIO_IB_ATMU_AR + | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE)); + + /* configure inbound window for slave's ucode */ + debug("SRIOBOOT - MASTER: Inbound window for slave's ucode; " + "Local = 0x%llx, Srio = 0x%llx, Size = 0x%x\n", + (u64)CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS, + (u64)CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS, + CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwtar, + CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwbar, + CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[2].riwar, + SRIO_IB_ATMU_AR + | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE)); + + /* configure inbound window for slave's ENV */ + debug("SRIOBOOT - MASTER: Inbound window for slave's ENV; " + "Local = 0x%llx, Siro = 0x%llx, Size = 0x%x\n", + CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS, + CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS, + CONFIG_SRIOBOOT_SLAVE_ENV_SIZE); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwtar, + CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwbar, + CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT].inbw[3].riwar, + SRIO_IB_ATMU_AR + | atmu_size_mask(CONFIG_SRIOBOOT_SLAVE_ENV_SIZE)); +} + +#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF +void srio_boot_master_release_slave(void) +{ + struct ccsr_rio *srio = (void *)CONFIG_SYS_FSL_SRIO_ADDR; + u32 escsr; + debug("SRIOBOOT - MASTER: " + "Check the port status and release slave core ...\n"); + + escsr = in_be32((void *)&srio->lp_serial + .port[CONFIG_SRIOBOOT_MASTER_PORT].pescsr); + if (escsr & 0x2) { + if (escsr & 0x10100) { + debug("SRIOBOOT - MASTER: Port [ %d ] is error.\n", + CONFIG_SRIOBOOT_MASTER_PORT); + } else { + debug("SRIOBOOT - MASTER: " + "Port [ %d ] is ready, now release slave's core ...\n", + CONFIG_SRIOBOOT_MASTER_PORT); + /* + * configure outbound window + * with maintenance attribute to set slave's LCSBA1CSR + */ + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[1].rowtar, 0); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[1].rowtear, 0); + if (CONFIG_SRIOBOOT_MASTER_PORT) + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[1].rowbar, + CONFIG_SYS_SRIO2_MEM_PHYS >> 12); + else + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[1].rowbar, + CONFIG_SYS_SRIO1_MEM_PHYS >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[1].rowar, + SRIO_OB_ATMU_AR_MAINT + | atmu_size_mask(SRIO_MAINT_WIN_SIZE)); + + /* + * configure outbound window + * with R/W attribute to set slave's BRR + */ + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[2].rowtar, + SRIO_LCSBA1CSR >> 9); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[2].rowtear, 0); + if (CONFIG_SRIOBOOT_MASTER_PORT) + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[2].rowbar, + (CONFIG_SYS_SRIO2_MEM_PHYS + + SRIO_MAINT_WIN_SIZE) >> 12); + else + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[2].rowbar, + (CONFIG_SYS_SRIO1_MEM_PHYS + + SRIO_MAINT_WIN_SIZE) >> 12); + out_be32((void *)&srio->atmu + .port[CONFIG_SRIOBOOT_MASTER_PORT] + .outbw[2].rowar, + SRIO_OB_ATMU_AR_RW + | atmu_size_mask(SRIO_RW_WIN_SIZE)); + + /* + * Set the LCSBA1CSR register in slave + * by the maint-outbound window + */ + if (CONFIG_SRIOBOOT_MASTER_PORT) { + out_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT + + SRIO_LCSBA1CSR_OFFSET, + SRIO_LCSBA1CSR); + while (in_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT + + SRIO_LCSBA1CSR_OFFSET) + != SRIO_LCSBA1CSR) + ; + /* + * And then set the BRR register + * to release slave core + */ + out_be32((void *)CONFIG_SYS_SRIO2_MEM_VIRT + + SRIO_MAINT_WIN_SIZE + + CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET, + CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK); + } else { + out_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT + + SRIO_LCSBA1CSR_OFFSET, + SRIO_LCSBA1CSR); + while (in_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT + + SRIO_LCSBA1CSR_OFFSET) + != SRIO_LCSBA1CSR) + ; + /* + * And then set the BRR register + * to release slave core + */ + out_be32((void *)CONFIG_SYS_SRIO1_MEM_VIRT + + SRIO_MAINT_WIN_SIZE + + CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET, + CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK); + } + debug("SRIOBOOT - MASTER: " + "Release slave successfully! Now the slave should start up!\n"); + } + } else + debug("SRIOBOOT - MASTER: Port [ %d ] is not ready.\n", + CONFIG_SRIOBOOT_MASTER_PORT); +} +#endif +#endif diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 8654625fac..191629b628 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -65,6 +65,11 @@ #define CONFIG_SYS_FSL_ERRATUM_NMG_DDR120 #define CONFIG_SYS_FSL_ERRATUM_NMG_LBC103 #define CONFIG_SYS_FSL_ERRATUM_NMG_ETSEC129 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_RMU +#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 #elif defined(CONFIG_MPC8555) #define CONFIG_MAX_CPUS 1 @@ -85,6 +90,11 @@ #define MAX_QE_RISC 2 #define QE_NUM_OF_SNUM 28 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_RMU +#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 #elif defined(CONFIG_MPC8569) #define CONFIG_MAX_CPUS 1 @@ -94,6 +104,11 @@ #define MAX_QE_RISC 4 #define QE_NUM_OF_SNUM 46 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_RMU +#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 #elif defined(CONFIG_MPC8572) #define CONFIG_MAX_CPUS 2 @@ -298,6 +313,11 @@ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_RMU +#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 #elif defined(CONFIG_PPC_P2040) #define CONFIG_MAX_CPUS 4 @@ -317,6 +337,9 @@ #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #elif defined(CONFIG_PPC_P2041) #define CONFIG_MAX_CPUS 4 @@ -338,6 +361,9 @@ #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #elif defined(CONFIG_PPC_P3041) #define CONFIG_MAX_CPUS 4 @@ -359,6 +385,9 @@ #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #elif defined(CONFIG_PPC_P3060) #define CONFIG_MAX_CPUS 8 @@ -375,6 +404,9 @@ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #elif defined(CONFIG_PPC_P4040) #define CONFIG_MAX_CPUS 4 @@ -387,6 +419,9 @@ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #elif defined(CONFIG_PPC_P4080) #define CONFIG_MAX_CPUS 8 @@ -417,6 +452,11 @@ #define CONFIG_SYS_P4080_ERRATUM_SERDES_A005 #define CONFIG_SYS_FSL_ERRATUM_CPU_A003999 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 +#define CONFIG_SYS_FSL_RMU +#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2 /* P5010 is single core version of P5020 */ #elif defined(CONFIG_PPC_P5010) @@ -438,6 +478,9 @@ #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #elif defined(CONFIG_PPC_P5020) #define CONFIG_MAX_CPUS 2 @@ -458,6 +501,9 @@ #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003474 +#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2 +#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9 +#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5 #else #error Processor type not defined for this platform diff --git a/arch/powerpc/include/asm/fsl_srio.h b/arch/powerpc/include/asm/fsl_srio.h new file mode 100644 index 0000000000..a905a266c4 --- /dev/null +++ b/arch/powerpc/include/asm/fsl_srio.h @@ -0,0 +1,64 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _FSL_SRIO_H_ +#define _FSL_SRIO_H_ + +enum atmu_size { + ATMU_SIZE_4K = 0xb, + ATMU_SIZE_8K, + ATMU_SIZE_16K, + ATMU_SIZE_32K, + ATMU_SIZE_64K, + ATMU_SIZE_128K, + ATMU_SIZE_256K, + ATMU_SIZE_512K, + ATMU_SIZE_1M, + ATMU_SIZE_2M, + ATMU_SIZE_4M, + ATMU_SIZE_8M, + ATMU_SIZE_16M, + ATMU_SIZE_32M, + ATMU_SIZE_64M, + ATMU_SIZE_128M, + ATMU_SIZE_256M, + ATMU_SIZE_512M, + ATMU_SIZE_1G, + ATMU_SIZE_2G, + ATMU_SIZE_4G, + ATMU_SIZE_8G, + ATMU_SIZE_16G, + ATMU_SIZE_32G, + ATMU_SIZE_64G, +}; + +#define atmu_size_mask(sz) (__ilog2_u64(sz) - 1) +#define atmu_size_bytes(x) (1ULL << ((x & 0x3f) + 1)) + +extern void srio_init(void); +#ifdef CONFIG_SRIOBOOT_MASTER +extern void srio_boot_master(void); +#ifdef CONFIG_SRIOBOOT_SLAVE_HOLDOFF +extern void srio_boot_master_release_slave(void); +#endif +#endif +#endif diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 9b08cb8c1a..632e3c1669 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -1353,171 +1353,235 @@ typedef struct ccsr_cpm { } ccsr_cpm_t; #endif -/* RapidIO Registers */ -typedef struct ccsr_rio { - u32 didcar; /* Device Identity Capability */ - u32 dicar; /* Device Information Capability */ - u32 aidcar; /* Assembly Identity Capability */ - u32 aicar; /* Assembly Information Capability */ - u32 pefcar; /* Processing Element Features Capability */ - u32 spicar; /* Switch Port Information Capability */ - u32 socar; /* Source Operations Capability */ - u32 docar; /* Destination Operations Capability */ +#ifdef CONFIG_SYS_SRIO +/* Architectural regsiters */ +struct rio_arch { + u32 didcar; /* Device Identity CAR */ + u32 dicar; /* Device Information CAR */ + u32 aidcar; /* Assembly Identity CAR */ + u32 aicar; /* Assembly Information CAR */ + u32 pefcar; /* Processing Element Features CAR */ + u8 res0[4]; + u32 socar; /* Source Operations CAR */ + u32 docar; /* Destination Operations CAR */ u8 res1[32]; - u32 msr; /* Mailbox Cmd And Status */ - u32 pwdcsr; /* Port-Write & Doorbell Cmd And Status */ + u32 mcsr; /* Mailbox CSR */ + u32 pwdcsr; /* Port-Write and Doorbell CSR */ u8 res2[4]; u32 pellccsr; /* Processing Element Logic Layer CCSR */ u8 res3[12]; - u32 lcsbacsr; /* Local Cfg Space Base Addr Cmd & Status */ - u32 bdidcsr; /* Base Device ID Cmd & Status */ + u32 lcsbacsr; /* Local Configuration Space BACSR */ + u32 bdidcsr; /* Base Device ID CSR */ u8 res4[4]; - u32 hbdidlcsr; /* Host Base Device ID Lock Cmd & Status */ - u32 ctcsr; /* Component Tag Cmd & Status */ - u8 res5[144]; - u32 pmbh0csr; /* Port Maint. Block Hdr 0 Cmd & Status */ - u8 res6[28]; - u32 pltoccsr; /* Port Link Time-out Ctrl Cmd & Status */ - u32 prtoccsr; /* Port Response Time-out Ctrl Cmd & Status */ - u8 res7[20]; - u32 pgccsr; /* Port General Cmd & Status */ - u32 plmreqcsr; /* Port Link Maint. Request Cmd & Status */ - u32 plmrespcsr; /* Port Link Maint. Response Cmd & Status */ - u32 plascsr; /* Port Local Ackid Status Cmd & Status */ - u8 res8[12]; - u32 pescsr; /* Port Error & Status Cmd & Status */ - u32 pccsr; /* Port Control Cmd & Status */ - u8 res9[65184]; - u32 cr; /* Port Control Cmd & Status */ - u8 res10[12]; - u32 pcr; /* Port Configuration */ - u32 peir; /* Port Error Injection */ - u8 res11[3048]; - u32 rowtar0; /* RIO Outbound Window Translation Addr 0 */ - u8 res12[12]; - u32 rowar0; /* RIO Outbound Attrs 0 */ - u8 res13[12]; - u32 rowtar1; /* RIO Outbound Window Translation Addr 1 */ - u8 res14[4]; - u32 rowbar1; /* RIO Outbound Window Base Addr 1 */ - u8 res15[4]; - u32 rowar1; /* RIO Outbound Attrs 1 */ - u8 res16[12]; - u32 rowtar2; /* RIO Outbound Window Translation Addr 2 */ - u8 res17[4]; - u32 rowbar2; /* RIO Outbound Window Base Addr 2 */ - u8 res18[4]; - u32 rowar2; /* RIO Outbound Attrs 2 */ - u8 res19[12]; - u32 rowtar3; /* RIO Outbound Window Translation Addr 3 */ - u8 res20[4]; - u32 rowbar3; /* RIO Outbound Window Base Addr 3 */ - u8 res21[4]; - u32 rowar3; /* RIO Outbound Attrs 3 */ - u8 res22[12]; - u32 rowtar4; /* RIO Outbound Window Translation Addr 4 */ - u8 res23[4]; - u32 rowbar4; /* RIO Outbound Window Base Addr 4 */ - u8 res24[4]; - u32 rowar4; /* RIO Outbound Attrs 4 */ - u8 res25[12]; - u32 rowtar5; /* RIO Outbound Window Translation Addr 5 */ - u8 res26[4]; - u32 rowbar5; /* RIO Outbound Window Base Addr 5 */ - u8 res27[4]; - u32 rowar5; /* RIO Outbound Attrs 5 */ - u8 res28[12]; - u32 rowtar6; /* RIO Outbound Window Translation Addr 6 */ - u8 res29[4]; - u32 rowbar6; /* RIO Outbound Window Base Addr 6 */ - u8 res30[4]; - u32 rowar6; /* RIO Outbound Attrs 6 */ - u8 res31[12]; - u32 rowtar7; /* RIO Outbound Window Translation Addr 7 */ - u8 res32[4]; - u32 rowbar7; /* RIO Outbound Window Base Addr 7 */ - u8 res33[4]; - u32 rowar7; /* RIO Outbound Attrs 7 */ - u8 res34[12]; - u32 rowtar8; /* RIO Outbound Window Translation Addr 8 */ - u8 res35[4]; - u32 rowbar8; /* RIO Outbound Window Base Addr 8 */ - u8 res36[4]; - u32 rowar8; /* RIO Outbound Attrs 8 */ - u8 res37[76]; - u32 riwtar4; /* RIO Inbound Window Translation Addr 4 */ - u8 res38[4]; - u32 riwbar4; /* RIO Inbound Window Base Addr 4 */ - u8 res39[4]; - u32 riwar4; /* RIO Inbound Attrs 4 */ - u8 res40[12]; - u32 riwtar3; /* RIO Inbound Window Translation Addr 3 */ - u8 res41[4]; - u32 riwbar3; /* RIO Inbound Window Base Addr 3 */ - u8 res42[4]; - u32 riwar3; /* RIO Inbound Attrs 3 */ - u8 res43[12]; - u32 riwtar2; /* RIO Inbound Window Translation Addr 2 */ - u8 res44[4]; - u32 riwbar2; /* RIO Inbound Window Base Addr 2 */ - u8 res45[4]; - u32 riwar2; /* RIO Inbound Attrs 2 */ - u8 res46[12]; - u32 riwtar1; /* RIO Inbound Window Translation Addr 1 */ - u8 res47[4]; - u32 riwbar1; /* RIO Inbound Window Base Addr 1 */ - u8 res48[4]; - u32 riwar1; /* RIO Inbound Attrs 1 */ - u8 res49[12]; - u32 riwtar0; /* RIO Inbound Window Translation Addr 0 */ - u8 res50[12]; - u32 riwar0; /* RIO Inbound Attrs 0 */ - u8 res51[12]; - u32 pnfedr; /* Port Notification/Fatal Error Detect */ - u32 pnfedir; /* Port Notification/Fatal Error Detect */ - u32 pnfeier; /* Port Notification/Fatal Error IRQ Enable */ - u32 pecr; /* Port Error Control */ - u32 pepcsr0; /* Port Error Packet/Control Symbol 0 */ - u32 pepr1; /* Port Error Packet 1 */ - u32 pepr2; /* Port Error Packet 2 */ - u8 res52[4]; - u32 predr; /* Port Recoverable Error Detect */ - u8 res53[4]; - u32 pertr; /* Port Error Recovery Threshold */ - u32 prtr; /* Port Retry Threshold */ - u8 res54[464]; - u32 omr; /* Outbound Mode */ - u32 osr; /* Outbound Status */ - u32 eodqtpar; /* Extended Outbound Desc Queue Tail Ptr Addr */ - u32 odqtpar; /* Outbound Desc Queue Tail Ptr Addr */ - u32 eosar; /* Extended Outbound Unit Source Addr */ - u32 osar; /* Outbound Unit Source Addr */ - u32 odpr; /* Outbound Destination Port */ - u32 odatr; /* Outbound Destination Attrs */ - u32 odcr; /* Outbound Doubleword Count */ - u32 eodqhpar; /* Extended Outbound Desc Queue Head Ptr Addr */ - u32 odqhpar; /* Outbound Desc Queue Head Ptr Addr */ - u8 res55[52]; - u32 imr; /* Outbound Mode */ - u32 isr; /* Inbound Status */ - u32 eidqtpar; /* Extended Inbound Desc Queue Tail Ptr Addr */ - u32 idqtpar; /* Inbound Desc Queue Tail Ptr Addr */ - u32 eifqhpar; /* Extended Inbound Frame Queue Head Ptr Addr */ - u32 ifqhpar; /* Inbound Frame Queue Head Ptr Addr */ - u8 res56[1000]; - u32 dmr; /* Doorbell Mode */ - u32 dsr; /* Doorbell Status */ - u32 edqtpar; /* Extended Doorbell Queue Tail Ptr Addr */ - u32 dqtpar; /* Doorbell Queue Tail Ptr Addr */ - u32 edqhpar; /* Extended Doorbell Queue Head Ptr Addr */ - u32 dqhpar; /* Doorbell Queue Head Ptr Addr */ - u8 res57[104]; - u32 pwmr; /* Port-Write Mode */ - u32 pwsr; /* Port-Write Status */ - u32 epwqbar; /* Extended Port-Write Queue Base Addr */ - u32 pwqbar; /* Port-Write Queue Base Addr */ - u8 res58[60176]; -} ccsr_rio_t; + u32 hbdidlcsr; /* Host Base Device ID Lock CSR */ + u32 ctcsr; /* Component Tag CSR */ +}; + +/* Extended Features Space: 1x/4x LP-Serial Port registers */ +struct rio_lp_serial_port { + u32 plmreqcsr; /* Port Link Maintenance Request CSR */ + u32 plmrespcsr; /* Port Link Maintenance Response CS */ + u32 plascsr; /* Port Local Ackid Status CSR */ + u8 res0[12]; + u32 pescsr; /* Port Error and Status CSR */ + u32 pccsr; /* Port Control CSR */ +}; + +/* Extended Features Space: 1x/4x LP-Serial registers */ +struct rio_lp_serial { + u32 pmbh0csr; /* Port Maintenance Block Header 0 CSR */ + u8 res0[28]; + u32 pltoccsr; /* Port Link Time-out CCSR */ + u32 prtoccsr; /* Port Response Time-out CCSR */ + u8 res1[20]; + u32 pgccsr; /* Port General CSR */ + struct rio_lp_serial_port port[CONFIG_SYS_FSL_SRIO_MAX_PORTS]; +}; + +/* Logical error reporting registers */ +struct rio_logical_err { + u32 erbh; /* Error Reporting Block Header Register */ + u8 res0[4]; + u32 ltledcsr; /* Logical/Transport layer error DCSR */ + u32 ltleecsr; /* Logical/Transport layer error ECSR */ + u8 res1[4]; + u32 ltlaccsr; /* Logical/Transport layer ACCSR */ + u32 ltldidccsr; /* Logical/Transport layer DID CCSR */ + u32 ltlcccsr; /* Logical/Transport layer control CCSR */ +}; + +/* Physical error reporting port registers */ +struct rio_phys_err_port { + u32 edcsr; /* Port error detect CSR */ + u32 erecsr; /* Port error rate enable CSR */ + u32 ecacsr; /* Port error capture attributes CSR */ + u32 pcseccsr0; /* Port packet/control symbol ECCSR 0 */ + u32 peccsr[3]; /* Port error capture CSR */ + u8 res0[12]; + u32 ercsr; /* Port error rate CSR */ + u32 ertcsr; /* Port error rate threshold CSR */ + u8 res1[16]; +}; + +/* Physical error reporting registers */ +struct rio_phys_err { + struct rio_phys_err_port port[CONFIG_SYS_FSL_SRIO_MAX_PORTS]; +}; + +/* Implementation Space: General Port-Common */ +struct rio_impl_common { + u8 res0[4]; + u32 llcr; /* Logical Layer Configuration Register */ + u8 res1[8]; + u32 epwisr; /* Error / Port-Write Interrupt SR */ + u8 res2[12]; + u32 lretcr; /* Logical Retry Error Threshold CR */ + u8 res3[92]; + u32 pretcr; /* Physical Retry Erorr Threshold CR */ + u8 res4[124]; +}; + +/* Implementation Space: Port Specific */ +struct rio_impl_port_spec { + u32 adidcsr; /* Port Alt. Device ID CSR */ + u8 res0[28]; + u32 ptaacr; /* Port Pass-Through/Accept-All CR */ + u32 lopttlcr; + u8 res1[8]; + u32 iecsr; /* Port Implementation Error CSR */ + u8 res2[12]; + u32 pcr; /* Port Phsyical Configuration Register */ + u8 res3[20]; + u32 slcsr; /* Port Serial Link CSR */ + u8 res4[4]; + u32 sleicr; /* Port Serial Link Error Injection */ + u32 a0txcr; /* Port Arbitration 0 Tx CR */ + u32 a1txcr; /* Port Arbitration 1 Tx CR */ + u32 a2txcr; /* Port Arbitration 2 Tx CR */ + u32 mreqtxbacr[3]; /* Port Request Tx Buffer ACR */ + u32 mrspfctxbacr; /* Port Response/Flow Control Tx Buffer ACR */ +}; + +/* Implementation Space: register */ +struct rio_implement { + struct rio_impl_common com; + struct rio_impl_port_spec port[CONFIG_SYS_FSL_SRIO_MAX_PORTS]; +}; + +/* Revision Control Register */ +struct rio_rev_ctrl { + u32 ipbrr[2]; /* IP Block Revision Register */ +}; + +struct rio_atmu_row { + u32 rowtar; /* RapidIO Outbound Window TAR */ + u32 rowtear; /* RapidIO Outbound Window TEAR */ + u32 rowbar; + u8 res0[4]; + u32 rowar; /* RapidIO Outbound Attributes Register */ + u32 rowsr[3]; /* Port RapidIO outbound window segment register */ +}; + +struct rio_atmu_riw { + u32 riwtar; /* RapidIO Inbound Window Translation AR */ + u8 res0[4]; + u32 riwbar; /* RapidIO Inbound Window Base AR */ + u8 res1[4]; + u32 riwar; /* RapidIO Inbound Attributes Register */ + u8 res2[12]; +}; + +/* ATMU window registers */ +struct rio_atmu_win { + struct rio_atmu_row outbw[CONFIG_SYS_FSL_SRIO_OB_WIN_NUM]; + u8 res0[64]; + struct rio_atmu_riw inbw[CONFIG_SYS_FSL_SRIO_IB_WIN_NUM]; +}; + +struct rio_atmu { + struct rio_atmu_win port[CONFIG_SYS_FSL_SRIO_MAX_PORTS]; +}; + +#ifdef CONFIG_SYS_FSL_RMU +struct rio_msg { + u32 omr; /* Outbound Mode Register */ + u32 osr; /* Outbound Status Register */ + u32 eodqdpar; /* Extended Outbound DQ DPAR */ + u32 odqdpar; /* Outbound Descriptor Queue DPAR */ + u32 eosar; /* Extended Outbound Unit Source AR */ + u32 osar; /* Outbound Unit Source AR */ + u32 odpr; /* Outbound Destination Port Register */ + u32 odatr; /* Outbound Destination Attributes Register */ + u32 odcr; /* Outbound Doubleword Count Register */ + u32 eodqepar; /* Extended Outbound DQ EPAR */ + u32 odqepar; /* Outbound Descriptor Queue EPAR */ + u32 oretr; /* Outbound Retry Error Threshold Register */ + u32 omgr; /* Outbound Multicast Group Register */ + u32 omlr; /* Outbound Multicast List Register */ + u8 res0[40]; + u32 imr; /* Outbound Mode Register */ + u32 isr; /* Inbound Status Register */ + u32 eidqdpar; /* Extended Inbound Descriptor Queue DPAR */ + u32 idqdpar; /* Inbound Descriptor Queue DPAR */ + u32 eifqepar; /* Extended Inbound Frame Queue EPAR */ + u32 ifqepar; /* Inbound Frame Queue EPAR */ + u32 imirir; /* Inbound Maximum Interrutp RIR */ + u8 res1[4]; + u32 eihqepar; /* Extended inbound message header queue EPAR */ + u32 ihqepar; /* Inbound message header queue EPAR */ + u8 res2[120]; +}; + +struct rio_dbell { + u32 odmr; /* Outbound Doorbell Mode Register */ + u32 odsr; /* Outbound Doorbell Status Register */ + u8 res0[16]; + u32 oddpr; /* Outbound Doorbell Destination Port */ + u32 oddatr; /* Outbound Doorbell Destination AR */ + u8 res1[12]; + u32 oddretr; /* Outbound Doorbell Retry Threshold CR */ + u8 res2[48]; + u32 idmr; /* Inbound Doorbell Mode Register */ + u32 idsr; /* Inbound Doorbell Status Register */ + u32 iedqdpar; /* Extended Inbound Doorbell Queue DPAR */ + u32 iqdpar; /* Inbound Doorbell Queue DPAR */ + u32 iedqepar; /* Extended Inbound Doorbell Queue EPAR */ + u32 idqepar; /* Inbound Doorbell Queue EPAR */ + u32 idmirir; /* Inbound Doorbell Max Interrupt RIR */ +}; + +struct rio_pw { + u32 pwmr; /* Port-Write Mode Register */ + u32 pwsr; /* Port-Write Status Register */ + u32 epwqbar; /* Extended Port-Write Queue BAR */ + u32 pwqbar; /* Port-Write Queue Base Address Register */ +}; +#endif + +/* RapidIO Registers */ +struct ccsr_rio { + struct rio_arch arch; + u8 res0[144]; + struct rio_lp_serial lp_serial; + u8 res1[1152]; + struct rio_logical_err logical_err; + u8 res2[32]; + struct rio_phys_err phys_err; + u8 res3[63808]; + struct rio_implement impl; + u8 res4[2552]; + struct rio_rev_ctrl rev; + struct rio_atmu atmu; +#ifdef CONFIG_SYS_FSL_RMU + u8 res5[8192]; + struct rio_msg msg[CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM]; + u8 res6[512]; + struct rio_dbell dbell; + u8 res7[100]; + struct rio_pw pw; +#endif +}; +#endif /* Quick Engine Block Pin Muxing Registers */ typedef struct par_io { @@ -2443,6 +2507,7 @@ struct ccsr_rman { #define CONFIG_SYS_MPC85xx_PIC_OFFSET 0x40000 #define CONFIG_SYS_MPC85xx_GUTS_OFFSET 0xE0000 +#define CONFIG_SYS_FSL_SRIO_OFFSET 0xC0000 #define CONFIG_SYS_FSL_CPC_ADDR \ (CONFIG_SYS_CCSRBAR + CONFIG_SYS_FSL_CPC_OFFSET) @@ -2516,6 +2581,8 @@ struct ccsr_rman { (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_FM1_DTSEC1_OFFSET) #define CONFIG_SYS_FSL_FM2_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_FM2_OFFSET) +#define CONFIG_SYS_FSL_SRIO_ADDR \ + (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_SRIO_OFFSET) #define CONFIG_SYS_PCI1_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PCI1_OFFSET) diff --git a/board/freescale/common/p_corenet/law.c b/board/freescale/common/p_corenet/law.c index 09ef5615d2..c4566ddd4f 100644 --- a/board/freescale/common/p_corenet/law.c +++ b/board/freescale/common/p_corenet/law.c @@ -48,6 +48,19 @@ struct law_entry law_table[] = { #ifdef CONFIG_SYS_NAND_BASE_PHYS SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), #endif +#ifdef CONFIG_SRIOBOOT_SLAVE +#if defined(CONFIG_SRIOBOOT_SLAVE_PORT0) + SET_LAW(CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS, + LAW_SIZE_1M, LAW_TRGT_IF_RIO_1), + SET_LAW(CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS, + LAW_SIZE_1M, LAW_TRGT_IF_RIO_1), +#elif defined(CONFIG_SRIOBOOT_SLAVE_PORT1) + SET_LAW(CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS, + LAW_SIZE_1M, LAW_TRGT_IF_RIO_2), + SET_LAW(CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS, + LAW_SIZE_1M, LAW_TRGT_IF_RIO_2), +#endif +#endif }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/common/p_corenet/tlb.c b/board/freescale/common/p_corenet/tlb.c index 6a0026a2cf..da2162728f 100644 --- a/board/freescale/common/p_corenet/tlb.c +++ b/board/freescale/common/p_corenet/tlb.c @@ -66,6 +66,15 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 0, BOOKE_PAGESZ_1M, 1), +#elif defined(CONFIG_SRIOBOOT_SLAVE) + /* + * SRIOBOOT-SLAVE. When slave boot, the address of the + * space is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIOBOOT_SLAVE_ADDR, + CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), #else SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -138,6 +147,16 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 16, BOOKE_PAGESZ_1M, 1), #endif +#ifdef CONFIG_SRIOBOOT_SLAVE + /* + * SRIOBOOT-SLAVE. 1M space from 0xffe00000 for fetching ucode + * and ENV from master + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR, + CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 17, BOOKE_PAGESZ_1M, 1), +#endif }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/corenet_ds/corenet_ds.c b/board/freescale/corenet_ds/corenet_ds.c index b1eecc495d..a33c936fa0 100644 --- a/board/freescale/corenet_ds/corenet_ds.c +++ b/board/freescale/corenet_ds/corenet_ds.c @@ -62,10 +62,6 @@ int checkboard (void) else printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH); -#ifdef CONFIG_PHYS_64BIT - puts("36-bit Addressing\n"); -#endif - /* Display the RCW, so that no one gets confused as to what RCW * we're actually using for this boot. */ diff --git a/board/freescale/mpc8536ds/mpc8536ds.c b/board/freescale/mpc8536ds/mpc8536ds.c index c9f85c857b..6d0bfde232 100644 --- a/board/freescale/mpc8536ds/mpc8536ds.c +++ b/board/freescale/mpc8536ds/mpc8536ds.c @@ -68,12 +68,7 @@ int checkboard (void) u8 vboot; u8 *pixis_base = (u8 *)PIXIS_BASE; - puts("Board: MPC8536DS "); -#ifdef CONFIG_PHYS_64BIT - puts("(36-bit addrmap) "); -#endif - - printf ("Sys ID: 0x%02x, " + printf("Board: MPC8536DS Sys ID: 0x%02x, " "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER), in_8(pixis_base + PIXIS_PVER)); diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c index b20299e36f..33a02ba8d3 100644 --- a/board/freescale/mpc8572ds/mpc8572ds.c +++ b/board/freescale/mpc8572ds/mpc8572ds.c @@ -45,11 +45,7 @@ int checkboard (void) u8 vboot; u8 *pixis_base = (u8 *)PIXIS_BASE; - puts ("Board: MPC8572DS "); -#ifdef CONFIG_PHYS_64BIT - puts ("(36-bit addrmap) "); -#endif - printf ("Sys ID: 0x%02x, " + printf("Board: MPC8572DS Sys ID: 0x%02x, " "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER), in_8(pixis_base + PIXIS_PVER)); diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index 455569e422..6a0a3a2b37 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -50,9 +50,6 @@ int checkboard(void) else puts ("Promjet\n"); -#ifdef CONFIG_PHYS_64BIT - printf (" 36-bit physical address map\n"); -#endif return 0; } diff --git a/board/freescale/p1010rdb/ddr.c b/board/freescale/p1010rdb/ddr.c index e5d8423df0..36c8545059 100644 --- a/board/freescale/p1010rdb/ddr.c +++ b/board/freescale/p1010rdb/ddr.c @@ -31,7 +31,7 @@ DECLARE_GLOBAL_DATA_PTR; -#ifndef CONFIG_DDR_RAW_TIMING +#ifndef CONFIG_SYS_DDR_RAW_TIMING #define CONFIG_SYS_DRAM_SIZE 1024 fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = { @@ -165,7 +165,7 @@ phys_size_t fixed_sdram(void) return ddr_size; } -#else /* CONFIG_DDR_RAW_TIMING */ +#else /* CONFIG_SYS_DDR_RAW_TIMING */ /* * Samsung K4B2G0846C-HCF8 * The following timing are for "downshift" @@ -247,4 +247,4 @@ void fsl_ddr_board_options(memctl_options_t *popts, } } -#endif /* CONFIG_DDR_RAW_TIMING */ +#endif /* CONFIG_SYS_DDR_RAW_TIMING */ diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c index b9e66f7fa7..79a6ead7dd 100644 --- a/board/freescale/p1010rdb/p1010rdb.c +++ b/board/freescale/p1010rdb/p1010rdb.c @@ -165,11 +165,7 @@ int checkboard(void) struct cpu_type *cpu; cpu = gd->cpu; - printf("Board: %sRDB ", cpu->name); -#ifdef CONFIG_PHYS_64BIT - puts("(36-bit addrmap)"); -#endif - puts("\n"); + printf("Board: %sRDB\n", cpu->name); return 0; } diff --git a/board/freescale/p1022ds/p1022ds.c b/board/freescale/p1022ds/p1022ds.c index 456d9b0e34..aca30f3680 100644 --- a/board/freescale/p1022ds/p1022ds.c +++ b/board/freescale/p1022ds/p1022ds.c @@ -56,12 +56,8 @@ int checkboard(void) { u8 sw; - puts("Board: P1022DS "); -#ifdef CONFIG_PHYS_64BIT - puts("(36-bit addrmap) "); -#endif - - printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", + printf("Board: P1022DS Sys ID: 0x%02x, " + "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver)); sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH)); diff --git a/board/freescale/p1023rds/p1023rds.c b/board/freescale/p1023rds/p1023rds.c index 546819cb59..082976a924 100644 --- a/board/freescale/p1023rds/p1023rds.c +++ b/board/freescale/p1023rds/p1023rds.c @@ -197,6 +197,12 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_memory(blob, (u64)base, (u64)size); + /* By default NOR is on, and NAND is disabled */ +#ifdef CONFIG_NAND_U_BOOT + do_fixup_by_path_string(blob, "nor_flash", "status", "disabled"); + do_fixup_by_path_string(blob, "nand_flash", "status", "okay"); +#endif + fdt_fixup_fman_ethernet(blob); } #endif diff --git a/board/freescale/p1_p2_rdb/p1_p2_rdb.c b/board/freescale/p1_p2_rdb/p1_p2_rdb.c index cfbae69119..437eaf0fdd 100644 --- a/board/freescale/p1_p2_rdb/p1_p2_rdb.c +++ b/board/freescale/p1_p2_rdb/p1_p2_rdb.c @@ -110,9 +110,7 @@ int checkboard (void) cpu = gd->cpu; printf ("Board: %sRDB Rev%c\n", cpu->name, board_rev); -#ifdef CONFIG_PHYS_64BIT - puts ("(36-bit addrmap) \n"); -#endif + setbits_be32(&pgpio->gpdir, GPIO_DIR); /* diff --git a/board/freescale/p1_p2_rdb_pc/ddr.c b/board/freescale/p1_p2_rdb_pc/ddr.c index f0cbde72ab..88ba56f457 100644 --- a/board/freescale/p1_p2_rdb_pc/ddr.c +++ b/board/freescale/p1_p2_rdb_pc/ddr.c @@ -15,7 +15,7 @@ #include <asm/io.h> #include <asm/fsl_law.h> -#ifdef CONFIG_DDR_RAW_TIMING +#ifdef CONFIG_SYS_DDR_RAW_TIMING #if defined(CONFIG_P1020RDB_PROTO) || \ defined(CONFIG_P1021RDB) || \ defined(CONFIG_P1020UTM) @@ -204,7 +204,7 @@ int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, return 0; } -#endif /* CONFIG_DDR_RAW_TIMING */ +#endif /* CONFIG_SYS_DDR_RAW_TIMING */ /* Fixed sdram init -- doesn't use serial presence detect. */ phys_size_t fixed_sdram(void) diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c index a60c5a20a9..aa39260ca7 100644 --- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c +++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c @@ -225,13 +225,7 @@ int checkboard(void) ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); u8 in, out, io_config, val; - printf("Board: %s ", CONFIG_BOARDNAME); - -#ifdef CONFIG_PHYS_64BIT - puts("(36-bit addrmap) "); -#endif - - printf("CPLD: V%d.%d PCBA: V%d.0\n", + printf("Board: %s CPLD: V%d.%d PCBA: V%d.0\n", CONFIG_BOARDNAME, in_8(&cpld_data->cpld_rev_major) & 0x0F, in_8(&cpld_data->cpld_rev_minor) & 0x0F, in_8(&cpld_data->pcba_rev) & 0x0F); diff --git a/board/freescale/p2020ds/p2020ds.c b/board/freescale/p2020ds/p2020ds.c index d3af6cf185..e8d31a4acf 100644 --- a/board/freescale/p2020ds/p2020ds.c +++ b/board/freescale/p2020ds/p2020ds.c @@ -61,12 +61,8 @@ int checkboard(void) { u8 sw; - puts("Board: P2020DS "); -#ifdef CONFIG_PHYS_64BIT - puts("(36-bit addrmap) "); -#endif - - printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", + printf("Board: P2020DS Sys ID: 0x%02x, " + "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver)); sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH)); diff --git a/board/freescale/p2041rdb/p2041rdb.c b/board/freescale/p2041rdb/p2041rdb.c index 1f6a34b3d9..976c8d290b 100644 --- a/board/freescale/p2041rdb/p2041rdb.c +++ b/board/freescale/p2041rdb/p2041rdb.c @@ -54,10 +54,6 @@ int checkboard(void) sw = CPLD_READ(fbank_sel); printf("vBank: %d\n", sw & 0x1); -#ifdef CONFIG_PHYS_64BIT - puts("36-bit Addressing\n"); -#endif - /* * Display the RCW, so that no one gets confused as to what RCW * we're actually using for this boot. diff --git a/board/freescale/p3060qds/p3060qds.c b/board/freescale/p3060qds/p3060qds.c index c6c74f2004..c7cca2a0cc 100644 --- a/board/freescale/p3060qds/p3060qds.c +++ b/board/freescale/p3060qds/p3060qds.c @@ -68,9 +68,6 @@ int checkboard(void) else printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH); -#ifdef CONFIG_PHYS_64BIT - puts("36-bit Addressing\n"); -#endif puts("Reset Configuration Word (RCW):"); for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) { u32 rcw = in_be32(&gur->rcwsr[i]); diff --git a/boards.cfg b/boards.cfg index 3b8be8709e..15339f7a65 100644 --- a/boards.cfg +++ b/boards.cfg @@ -743,6 +743,7 @@ P2020RDB-PC_SPIFLASH powerpc mpc85xx p1_p2_rdb_pc freesca P2020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SDCARD P2020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SPIFLASH P2041RDB powerpc mpc85xx p2041rdb freescale +P2041RDB_NAND powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 P2041RDB_SDCARD powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P2041RDB_SECURE_BOOT powerpc mpc85xx p2041rdb freescale - P2041RDB:SECURE_BOOT P2041RDB_SPIFLASH powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 @@ -751,6 +752,8 @@ P3041DS_NAND powerpc mpc85xx corenet_ds freescale - P3041DS_SDCARD powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P3041DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P3041DS:SECURE_BOOT P3041DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +P3041DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P3041DS:SRIOBOOT_MASTER +P3041DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P3041DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 P3060QDS powerpc mpc85xx p3060qds freescale P3060QDS_NAND powerpc mpc85xx p3060qds freescale - P3060QDS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 P3060QDS_SECURE_BOOT powerpc mpc85xx p3060qds freescale - P3060QDS:SECURE_BOOT @@ -758,11 +761,15 @@ P4080DS powerpc mpc85xx corenet_ds freesca P4080DS_SDCARD powerpc mpc85xx corenet_ds freescale - P4080DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P4080DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P4080DS:SECURE_BOOT P4080DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P4080DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +P4080DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P4080DS:SRIOBOOT_MASTER +P4080DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P4080DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 P5020DS powerpc mpc85xx corenet_ds freescale P5020DS_NAND powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 P5020DS_SDCARD powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 P5020DS_SECURE_BOOT powerpc mpc85xx corenet_ds freescale - P5020DS:SECURE_BOOT P5020DS_SPIFLASH powerpc mpc85xx corenet_ds freescale - P5020DS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 +P5020DS_SRIOBOOT_MASTER powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_MASTER +P5020DS_SRIOBOOT_SLAVE powerpc mpc85xx corenet_ds freescale - P5020DS:SRIOBOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 stxgp3 powerpc mpc85xx stxgp3 stx stxssa powerpc mpc85xx stxssa stx - stxssa stxssa_4M powerpc mpc85xx stxssa stx - stxssa:STXSSA_4M diff --git a/common/Makefile b/common/Makefile index d9f10f3f6e..6e23baaf61 100644 --- a/common/Makefile +++ b/common/Makefile @@ -59,6 +59,7 @@ COBJS-$(CONFIG_ENV_IS_IN_NAND) += env_nand.o COBJS-$(CONFIG_ENV_IS_IN_NVRAM) += env_nvram.o COBJS-$(CONFIG_ENV_IS_IN_ONENAND) += env_onenand.o COBJS-$(CONFIG_ENV_IS_IN_SPI_FLASH) += env_sf.o +COBJS-$(CONFIG_ENV_IS_IN_REMOTE) += env_remote.o COBJS-$(CONFIG_ENV_IS_NOWHERE) += env_nowhere.o # command diff --git a/common/cmd_bdinfo.c b/common/cmd_bdinfo.c index 5359a47859..3ab285bc73 100644 --- a/common/cmd_bdinfo.c +++ b/common/cmd_bdinfo.c @@ -119,6 +119,14 @@ int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) print_mhz("pevfreq", bd->bi_pevfreq); #endif +#ifdef CONFIG_ENABLE_36BIT_PHYS +#ifdef CONFIG_PHYS_64BIT + puts("addressing = 36-bit\n"); +#else + puts("addressing = 32-bit\n"); +#endif +#endif + print_eth(0); #if defined(CONFIG_HAS_ETH1) print_eth(1); diff --git a/common/cmd_nvedit.c b/common/cmd_nvedit.c index b1494dcb0c..e1ccdd8f7e 100644 --- a/common/cmd_nvedit.c +++ b/common/cmd_nvedit.c @@ -66,9 +66,10 @@ DECLARE_GLOBAL_DATA_PTR; !defined(CONFIG_ENV_IS_IN_NVRAM) && \ !defined(CONFIG_ENV_IS_IN_ONENAND) && \ !defined(CONFIG_ENV_IS_IN_SPI_FLASH) && \ + !defined(CONFIG_ENV_IS_IN_REMOTE) && \ !defined(CONFIG_ENV_IS_NOWHERE) # error Define one of CONFIG_ENV_IS_IN_{EEPROM|FLASH|DATAFLASH|ONENAND|\ -SPI_FLASH|MG_DISK|NVRAM|MMC|FAT} or CONFIG_ENV_IS_NOWHERE +SPI_FLASH|MG_DISK|NVRAM|MMC|FAT|REMOTE} or CONFIG_ENV_IS_NOWHERE #endif #define XMK_STR(x) #x diff --git a/common/env_remote.c b/common/env_remote.c new file mode 100644 index 0000000000..3bf0f957b3 --- /dev/null +++ b/common/env_remote.c @@ -0,0 +1,79 @@ +/* + * (C) Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* #define DEBUG */ + +#include <common.h> +#include <command.h> +#include <environment.h> +#include <linux/stddef.h> + +char *env_name_spec = "Remote"; + +#ifdef ENV_IS_EMBEDDED +env_t *env_ptr = &environment; +#else /* ! ENV_IS_EMBEDDED */ +env_t *env_ptr = (env_t *)CONFIG_ENV_ADDR; +#endif /* ENV_IS_EMBEDDED */ + +DECLARE_GLOBAL_DATA_PTR; + +#if !defined(CONFIG_ENV_OFFSET) +#define CONFIG_ENV_OFFSET 0 +#endif + +uchar env_get_char_spec(int index) +{ + return *((uchar *)(gd->env_addr + index)); +} + +int env_init(void) +{ + if (crc32(0, env_ptr->data, ENV_SIZE) == env_ptr->crc) { + gd->env_addr = (ulong)&(env_ptr->data); + gd->env_valid = 1; + return 0; + } + + gd->env_addr = (ulong)default_environment; + gd->env_valid = 0; + return 0; +} + +#ifdef CONFIG_CMD_SAVEENV +int saveenv(void) +{ +#ifdef CONFIG_SRIOBOOT_SLAVE + printf("Can not support the 'saveenv' when boot from SRIO!\n"); + return 1; +#else + return 0; +#endif +} +#endif /* CONFIG_CMD_SAVEENV */ + +void env_relocate_spec(void) +{ +#ifndef ENV_IS_EMBEDDED + env_import((char *)env_ptr, 1); +#endif +} diff --git a/doc/README.srio-boot-corenet b/doc/README.srio-boot-corenet new file mode 100644 index 0000000000..56b094c9a2 --- /dev/null +++ b/doc/README.srio-boot-corenet @@ -0,0 +1,103 @@ +------------------------------ +SRIO Boot on Corenet Platforms +------------------------------ + +For some PowerPC processors with SRIO interface, boot location can be configured +to SRIO by RCW. The processor booting from SRIO can do without flash for u-boot +image, ucode and ENV. All the images can be fetched from another processor's +memory space by SRIO link connected between them. + +This document describes the processes based on an example implemented on P4080DS +platforms and a RCW example with boot from SRIO configuration. + +Environment of the SRIO boot: + a) Master and slave can be SOCs in one board or SOCs in separate boards. + b) They are connected with SRIO links, whether 1x or 4x, and directly or + through switch system. + c) Only Master has NorFlash for booting, and all the Master's and Slave's + U-Boot images, UCodes will be stored in this flash. + d) Slave has its own EEPROM for RCW and PBI. + e) Slave's RCW should configure the SerDes for SRIO boot port, set the boot + location to SRIO, and holdoff all the cores if needed. + + ---------- ----------- ----------- + | | | | | | + | | | | | | + | NorFlash|<----->| Master | SRIO | Slave |<---->[EEPROM] + | | | |<===========>| | + | | | | | | + ---------- ----------- ----------- + +The example based on P4080DS platform: + Two P4080DS platforms can be used to implement the boot from SRIO. Their SRIO + ports 0 will be connected directly and will be used for the boot from SRIO. + + 1. Slave's RCW example for boot from SRIO port 0 and core 0 not in holdoff. + 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000 + 00000010: 1818 1818 0000 8888 7440 4000 0000 2000 + 00000020: f400 0000 0100 0000 0000 0000 0000 0000 + 00000030: 0000 0000 0083 0000 0000 0000 0000 0000 + 00000040: 0000 0000 0000 0000 0813 8040 698b 93fe + + 2. Slave's RCW example for boot from SRIO port 0 and all cores in holdoff. + 00000000: aa55 aa55 010e 0100 0c58 0000 0000 0000 + 00000010: 1818 1818 0000 8888 7440 4000 0000 2000 + 00000020: f440 0000 0100 0000 0000 0000 0000 0000 + 00000030: 0000 0000 0083 0000 0000 0000 0000 0000 + 00000040: 0000 0000 0000 0000 0813 8040 063c 778f + + 3. Sequence in Step by Step. + a) Update RCW for slave with boot from SRIO port 0 configuration. + b) Program slave's U-Boot image, UCode, and ENV parameters into master's + NorFlash. + c) Start up master and it will boot up normally from its NorFlash. + Then, it will finish necessary configurations for slave's boot from + SRIO port 0. + d) Master will set inbound SRIO windows covered slave's U-Boot image stored + in master's NorFlash. + e) Master will set an inbound SRIO window covered slave's UCode stored in + master's NorFlash. + f) Master will set an inbound SRIO window covered slave's ENV stored in + master's NorFlash. + g) If need to release slave's core, master will set outbound SRIO windows + in order to configure slave's registers for the core's releasing. + h) If all cores of slave in holdoff, slave should be powered on before all + the above master's steps, and wait to be released by master. If not all + cores in holdoff, that means core 0 will start up normally, slave should + be powered on after all the above master's steps. In the startup phase + of the slave from SRIO, it will finish some necessary configurations. + i) Slave will set a specific TLB entry for the boot process. + j) Slave will set a LAW entry with the TargetID SRIO port 0 for the boot. + k) Slave will set a specific TLB entry in order to fetch UCode and ENV + from master. + l) Slave will set a LAW entry with the TargetID SRIO port 0 for UCode and ENV. + +How to use this feature: + To use this feature, you need to focus three points. + + 1. Slave's RCW with SRIO boot configurations, and all cores in holdoff + configurations if needed. + Please refer to the examples given above. + + 2. U-Boot image's compilation. + For master, U-Boot image should be generated specifically by + + make xxxx_SRIOBOOT_MASTER_config. + + For example, master U-Boot image used on P4080DS should be compiled with + + make P4080DS_SRIOBOOT_MASTER_config. + + For slave, U-Boot image should be generated specifically by + + make xxxx_SRIOBOOT_SLAVE_config. + + For example, slave U-Boot image used on P4080DS should be compiled with + + make P4080DS_SRIOBOOT_SLAVE_config. + + 3. Necessary modifications based on a specific environment. + For a specific environment, the SRIO port for boot, the addresses of the + slave's U-Boot image, UCode, ENV stored in master's NorFlash, and any other + configurations can be modified in the file: + include/configs/corenet_ds.h. diff --git a/drivers/net/fm/fm.c b/drivers/net/fm/fm.c index 0b8c33fb7a..49c74c278a 100644 --- a/drivers/net/fm/fm.c +++ b/drivers/net/fm/fm.c @@ -408,6 +408,8 @@ int fm_init_common(int index, struct ccsr_fman *reg) /* flush cache after read */ flush_cache((ulong)addr, cnt * 512); } +#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_REMOTE) + void *addr = (void *)CONFIG_SYS_QE_FMAN_FW_ADDR; #endif /* Upload the Fman microcode if it's present */ diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index f2d33668d8..08fc4e8427 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -181,7 +181,7 @@ /* DDR Setup */ #define CONFIG_FSL_DDR3 -#define CONFIG_DDR_RAW_TIMING +#define CONFIG_SYS_DDR_RAW_TIMING #define CONFIG_DDR_SPD #define CONFIG_SYS_SPD_BUS_NUM 1 #define SPD_EEPROM_ADDRESS 0x52 diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index da98f8f027..fe39d4e6e6 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -96,6 +96,11 @@ #define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_OFFSET (512 * 1097) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ @@ -186,10 +191,11 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE #endif -#define CONFIG_SYS_BR0_PRELIM \ +#define CONFIG_SYS_FLASH_BR_PRELIM \ (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR0_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ - | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) +#define CONFIG_SYS_FLASH_OR_PRELIM \ + ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ + | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) #define CONFIG_FSL_CPLD #define CPLD_BASE 0xffdf0000 /* CPLD registers */ @@ -221,6 +227,53 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_RAMBOOT #endif +#define CONFIG_NAND_FSL_ELBC +/* Nand Flash */ +#ifdef CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull +#else +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#endif + +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* NAND flash config */ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ + | OR_FCM_PGS /* Large Page*/ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) + +#ifdef CONFIG_NAND +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ +#else +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ +#endif +#else +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ +#endif /* CONFIG_NAND_FSL_ELBC */ + #define CONFIG_SYS_FLASH_EMPTY_INFO #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index 77dd0a2d1e..8ed37a58c2 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -33,6 +33,15 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #endif +#ifdef CONFIG_SRIOBOOT_SLAVE +/* Set 1M boot space */ +#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) +#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIOBOOT_SLAVE_ADDR) +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_NO_FLASH +#endif + /* High Level Configuration Options */ #define CONFIG_BOOKE #define CONFIG_E500 /* BOOKE e500 family */ @@ -68,7 +77,9 @@ #define CONFIG_ENV_OVERWRITE #ifdef CONFIG_SYS_NO_FLASH +#ifndef CONFIG_SRIOBOOT_SLAVE #define CONFIG_ENV_IS_NOWHERE +#endif #else #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI @@ -97,6 +108,12 @@ #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIOBOOT_SLAVE) +#define CONFIG_ENV_IS_IN_REMOTE +#define CONFIG_ENV_ADDR 0xffe20000 +#define CONFIG_ENV_SIZE 0x2000 +#elif defined(CONFIG_ENV_IS_NOWHERE) +#define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) @@ -373,6 +390,54 @@ #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ /* + * SRIOBOOT - MASTER + */ +#ifdef CONFIG_SRIOBOOT_MASTER +/* master port for srioboot*/ +#define CONFIG_SRIOBOOT_MASTER_PORT 0 +/* #define CONFIG_SRIOBOOT_MASTER_PORT 1 */ +/* + * for slave u-boot IMAGE instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS1 0xfef080000ull +#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS1 0xfff80000ull +#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SIZE 0x80000 /* 512K */ +#define CONFIG_SRIOBOOT_SLAVE_IMAGE_LAW_PHYS2 0xfef080000ull +#define CONFIG_SRIOBOOT_SLAVE_IMAGE_SRIO_PHYS2 0x3fff80000ull +/* + * for slave UCODE instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIOBOOT_SLAVE_UCODE_LAW_PHYS 0xfef020000ull +#define CONFIG_SRIOBOOT_SLAVE_UCODE_SRIO_PHYS 0x3ffe00000ull +#define CONFIG_SRIOBOOT_SLAVE_UCODE_SIZE 0x10000 /* 64K */ +/* + * for slave ENV instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIOBOOT_SLAVE_ENV_LAW_PHYS 0xfef060000ull +#define CONFIG_SRIOBOOT_SLAVE_ENV_SRIO_PHYS 0x3ffe20000ull +#define CONFIG_SRIOBOOT_SLAVE_ENV_SIZE 0x20000 /* 128K */ +/* slave core release by master*/ +#define CONFIG_SRIOBOOT_SLAVE_HOLDOFF +#define CONFIG_SRIOBOOT_SLAVE_BRR_OFFSET 0xe00e4 +#define CONFIG_SRIOBOOT_SLAVE_RELEASE_MASK 0x00000001 /* release core 0 */ +#endif + +/* + * SRIOBOOT - SLAVE + */ +#ifdef CONFIG_SRIOBOOT_SLAVE +/* slave port for srioboot */ +#define CONFIG_SRIOBOOT_SLAVE_PORT0 +/* #define CONFIG_SRIOBOOT_SLAVE_PORT1 */ +#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR 0xFFE00000 +#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR) +#endif + +/* * eSPI - Enhanced SPI */ #define CONFIG_FSL_ESPI @@ -492,6 +557,16 @@ #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIOBOOT_SLAVE) +/* + * Slave has no ucode locally, it can fetch this from remote. When implementing + * in two corenet boards, slave's ucode could be stored in master's memory + * space, the address can be mapped from slave TLB->slave LAW-> + * slave SRIO outbound window->master inbound window->master LAW-> + * the ucode address in master's NOR flash. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index 3098c5acfe..9f2951d687 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -184,7 +184,7 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_CMD_SATA -#define CONFIG_SATA_SIL3114 +#define CONFIG_SATA_SIL #define CONFIG_SYS_SATA_MAX_DEVICE 2 #define CONFIG_LIBATA #define CONFIG_LBA48 @@ -227,7 +227,7 @@ /* DDR Setup */ #define CONFIG_FSL_DDR3 -#define CONFIG_DDR_RAW_TIMING +#define CONFIG_SYS_DDR_RAW_TIMING #define CONFIG_DDR_SPD #define CONFIG_SYS_SPD_BUS_NUM 1 #define SPD_EEPROM_ADDRESS 0x52 |
