diff options
| -rw-r--r-- | board/korat/korat.c | 42 | ||||
| -rw-r--r-- | include/configs/korat.h | 10 |
2 files changed, 47 insertions, 5 deletions
diff --git a/board/korat/korat.c b/board/korat/korat.c index a7b4b27c6d..dc977242ba 100644 --- a/board/korat/korat.c +++ b/board/korat/korat.c @@ -26,12 +26,15 @@ */ #include <common.h> +#include <fdt_support.h> #include <i2c.h> +#include <libfdt.h> #include <ppc440.h> +#include <asm/bitops.h> #include <asm/gpio.h> -#include <asm/processor.h> #include <asm/io.h> -#include <asm/bitops.h> +#include <asm/ppc4xx-intvec.h> +#include <asm/processor.h> DECLARE_GLOBAL_DATA_PTR; @@ -604,6 +607,16 @@ int testdram(void) } #endif /* defined(CFG_DRAM_TEST) */ +#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP) +/* + * Assign interrupts to PCI devices. + */ +void korat_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev) +{ + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIR2); +} +#endif + /* * pci_pre_init * @@ -654,6 +667,10 @@ int pci_pre_init(struct pci_controller *hose) addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep; mtdcr(plb1_acr, addr); +#if defined(CONFIG_PCI_PNP) + hose->fixup_irq = korat_pci_fixup_irq; +#endif + return 1; } #endif /* defined(CONFIG_PCI) */ @@ -779,3 +796,24 @@ int post_hotkeys_pressed(void) return 0; /* No hotkeys supported */ } #endif /* CONFIG_POST */ + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + u32 val[4]; + int rc; + + ft_cpu_setup(blob, bd); + + /* Fixup NOR mapping */ + val[0] = 1; /* chip select number */ + val[1] = 0; /* always 0 */ + val[2] = gd->bd->bi_flashstart; + val[3] = gd->bd->bi_flashsize - CFG_FLASH0_SIZE; + rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges", + val, sizeof(val), 1); + if (rc) + printf("Unable to update property NOR mapping, err=%s\n", + fdt_strerror(rc)); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/include/configs/korat.h b/include/configs/korat.h index 765566697f..e2610be933 100644 --- a/include/configs/korat.h +++ b/include/configs/korat.h @@ -129,7 +129,7 @@ #define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_FLASH1_TOP - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) @@ -185,7 +185,7 @@ #define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" /* Note: kernel_addr and ramdisk_addr assume that FLASH1 is 64 MiB. */ -#define CONFIG_EXTRA_ENV_SETTINGS \ +#define CONFIG_EXTRA_ENV_SETTINGS \ CFG_BOOTFILE \ CFG_ROOTPATH \ "netdev=eth0\0" \ @@ -216,7 +216,7 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_IBM_EMAC4_V4 1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 2 /* PHY address, See schematics */ #define CONFIG_PHY_DYNAMIC_ANEG 1 @@ -548,4 +548,8 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + #endif /* __CONFIG_H */ |
