diff options
100 files changed, 645 insertions, 694 deletions
@@ -1968,6 +1968,18 @@ CBFS (Coreboot Filesystem) support CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4 for defining speed and slave address + - drivers/i2c/fsl_i2c.c: + - activate i2c driver with CONFIG_SYS_I2C_FSL + define CONFIG_SYS_FSL_I2C_OFFSET for setting the register + offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and + CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first + bus. + - If your board supports a second fsl i2c bus, define + CONFIG_SYS_FSL_I2C2_OFFSET for the register offset + CONFIG_SYS_FSL_I2C2_SPEED for the speed and + CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the + second bus. + additional defines: CONFIG_SYS_NUM_I2C_BUSES @@ -2213,11 +2225,6 @@ CBFS (Coreboot Filesystem) support If not defined, then U-Boot uses predefined value for specified DTT device. - CONFIG_FSL_I2C - - Define this option if you want to use Freescale's I2C driver in - drivers/i2c/fsl_i2c.c. - CONFIG_I2C_MUX Define this option if you have I2C devices reached over 1 .. n diff --git a/arch/m68k/cpu/mcf5227x/cpu_init.c b/arch/m68k/cpu/mcf5227x/cpu_init.c index 1928eb384e..e9ac21a31d 100644 --- a/arch/m68k/cpu/mcf5227x/cpu_init.c +++ b/arch/m68k/cpu/mcf5227x/cpu_init.c @@ -105,7 +105,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_8(&gpio->par_i2c, GPIO_PAR_I2C_SCL_SCL | GPIO_PAR_I2C_SDA_SDA); #endif diff --git a/arch/m68k/cpu/mcf5227x/speed.c b/arch/m68k/cpu/mcf5227x/speed.c index 98f554aa7f..30d32071ad 100644 --- a/arch/m68k/cpu/mcf5227x/speed.c +++ b/arch/m68k/cpu/mcf5227x/speed.c @@ -134,7 +134,7 @@ int get_clocks(void) gd->bus_clk = gd->arch.flb_clk; } -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf523x/cpu_init.c b/arch/m68k/cpu/mcf523x/cpu_init.c index d1c0b401c1..1ad5d02d29 100644 --- a/arch/m68k/cpu/mcf523x/cpu_init.c +++ b/arch/m68k/cpu/mcf523x/cpu_init.c @@ -115,7 +115,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr7, CONFIG_SYS_CS7_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL CONFIG_SYS_I2C_PINMUX_REG &= CONFIG_SYS_I2C_PINMUX_CLR; CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET; #endif diff --git a/arch/m68k/cpu/mcf523x/speed.c b/arch/m68k/cpu/mcf523x/speed.c index ae462579e2..7876ba8ab5 100644 --- a/arch/m68k/cpu/mcf523x/speed.c +++ b/arch/m68k/cpu/mcf523x/speed.c @@ -47,7 +47,7 @@ int get_clocks(void) gd->bus_clk = CONFIG_SYS_CLK; gd->cpu_clk = (gd->bus_clk * 2); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf52x2/cpu_init.c b/arch/m68k/cpu/mcf52x2/cpu_init.c index 5d0e9f06f3..5d01670ca8 100644 --- a/arch/m68k/cpu/mcf52x2/cpu_init.c +++ b/arch/m68k/cpu/mcf52x2/cpu_init.c @@ -228,7 +228,7 @@ void cpu_init_f(void) /* FlexBus Chipselect */ init_fbcs(); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL CONFIG_SYS_I2C_PINMUX_REG = CONFIG_SYS_I2C_PINMUX_REG & CONFIG_SYS_I2C_PINMUX_CLR; CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET; @@ -498,7 +498,7 @@ void cpu_init_f(void) init_fbcs(); #endif /* #ifndef CONFIG_MONITOR_IS_IN_RAM */ -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL CONFIG_SYS_I2C_PINMUX_REG &= CONFIG_SYS_I2C_PINMUX_CLR; CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET; #endif diff --git a/arch/m68k/cpu/mcf52x2/speed.c b/arch/m68k/cpu/mcf52x2/speed.c index ba7dbaa1cf..ad68692323 100644 --- a/arch/m68k/cpu/mcf52x2/speed.c +++ b/arch/m68k/cpu/mcf52x2/speed.c @@ -90,9 +90,9 @@ int get_clocks (void) gd->bus_clk = gd->cpu_clk; #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; -#ifdef CONFIG_SYS_I2C2_OFFSET +#ifdef CONFIG_SYS_I2C2_FSL_OFFSET gd->arch.i2c2_clk = gd->bus_clk; #endif #endif diff --git a/arch/m68k/cpu/mcf532x/cpu_init.c b/arch/m68k/cpu/mcf532x/cpu_init.c index f571fadc35..bd7672d6f4 100644 --- a/arch/m68k/cpu/mcf532x/cpu_init.c +++ b/arch/m68k/cpu/mcf532x/cpu_init.c @@ -98,7 +98,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_8(&gpio->par_feci2c, GPIO_PAR_FECI2C_SDA_SDA | GPIO_PAR_FECI2C_SCL_SCL); #endif @@ -292,7 +292,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_8(&gpio->par_feci2c, GPIO_PAR_FECI2C_SCL_SCL | GPIO_PAR_FECI2C_SDA_SDA); #endif diff --git a/arch/m68k/cpu/mcf532x/speed.c b/arch/m68k/cpu/mcf532x/speed.c index 8efb451dc1..6e1d6a58e5 100644 --- a/arch/m68k/cpu/mcf532x/speed.c +++ b/arch/m68k/cpu/mcf532x/speed.c @@ -270,7 +270,7 @@ int get_clocks(void) gd->bus_clk = clock_pll(CONFIG_SYS_CLK / 1000, 0) * 1000; gd->cpu_clk = (gd->bus_clk * 3); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf5445x/cpu_init.c b/arch/m68k/cpu/mcf5445x/cpu_init.c index 6e947d06f9..3c53a7fe1e 100644 --- a/arch/m68k/cpu/mcf5445x/cpu_init.c +++ b/arch/m68k/cpu/mcf5445x/cpu_init.c @@ -212,7 +212,7 @@ void cpu_init_f(void) GPIO_PAR_FBCTL_OE | GPIO_PAR_FBCTL_TA_TA | GPIO_PAR_FBCTL_RW_RW | GPIO_PAR_FBCTL_TS_TS); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_FSL_I2C out_be16(&gpio->par_feci2c, GPIO_PAR_FECI2C_SCL_SCL | GPIO_PAR_FECI2C_SDA_SDA); #endif diff --git a/arch/m68k/cpu/mcf5445x/speed.c b/arch/m68k/cpu/mcf5445x/speed.c index 0276d4d826..3b341b8964 100644 --- a/arch/m68k/cpu/mcf5445x/speed.c +++ b/arch/m68k/cpu/mcf5445x/speed.c @@ -273,7 +273,7 @@ void setup_5445x_clocks(void) #endif } -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif } @@ -289,7 +289,7 @@ int get_clocks(void) setup_5445x_clocks(); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_FSL_I2C gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf547x_8x/cpu_init.c b/arch/m68k/cpu/mcf547x_8x/cpu_init.c index 4eb8a7c182..4c529dcf91 100644 --- a/arch/m68k/cpu/mcf547x_8x/cpu_init.c +++ b/arch/m68k/cpu/mcf547x_8x/cpu_init.c @@ -95,7 +95,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_be16(&gpio->par_feci2cirq, GPIO_PAR_FECI2CIRQ_SCL | GPIO_PAR_FECI2CIRQ_SDA); #endif diff --git a/arch/m68k/cpu/mcf547x_8x/speed.c b/arch/m68k/cpu/mcf547x_8x/speed.c index 41aae9d9eb..80e006b9e0 100644 --- a/arch/m68k/cpu/mcf547x_8x/speed.c +++ b/arch/m68k/cpu/mcf547x_8x/speed.c @@ -40,7 +40,7 @@ int get_clocks(void) gd->bus_clk = CONFIG_SYS_CLK; gd->cpu_clk = (gd->bus_clk * 2); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/include/asm/global_data.h b/arch/m68k/include/asm/global_data.h index 3ec298ff4a..58a481d834 100644 --- a/arch/m68k/include/asm/global_data.h +++ b/arch/m68k/include/asm/global_data.h @@ -26,7 +26,7 @@ /* Architecture-specific global data */ struct arch_global_data { -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL unsigned long i2c1_clk; unsigned long i2c2_clk; #endif diff --git a/board/esd/vme8349/vme8349.c b/board/esd/vme8349/vme8349.c index 96698e7203..8c8b8ee7ab 100644 --- a/board/esd/vme8349/vme8349.c +++ b/board/esd/vme8349/vme8349.c @@ -186,11 +186,11 @@ static spd_eeprom_t default_spd_eeprom = { int vme8349_read_spd(uchar chip, uint addr, int alen, uchar *buffer, int len) { - int old_bus = I2C_GET_BUS(); + int old_bus = i2c_get_bus_num(); unsigned int l, sum; int valid = 0; - I2C_SET_BUS(0); + i2c_set_bus_num(0); if (i2c_read(chip, addr, alen, buffer, len) == 0) if (memcmp(&buffer[64], &default_spd_eeprom.mid[0], 8) == 0) { @@ -215,7 +215,7 @@ int vme8349_read_spd(uchar chip, uint addr, int alen, uchar *buffer, int len) buffer[63] = sum; } - I2C_SET_BUS(old_bus); + i2c_set_bus_num(old_bus); return 0; } diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README index d5e7b05650..3178d49d0a 100644 --- a/board/freescale/m52277evb/README +++ b/board/freescale/m52277evb/README @@ -82,7 +82,7 @@ CONFIG_CMD_DATE -- enable to use date feature in u-boot CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README index 855bbd14e5..84fc1ecfb1 100644 --- a/board/freescale/m53017evb/README +++ b/board/freescale/m53017evb/README @@ -90,7 +90,7 @@ MCFFEC_TOUT_LOOP -- set FEC timeout loop CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README index 61e6d97b6d..52eac7b2ff 100644 --- a/board/freescale/m5373evb/README +++ b/board/freescale/m5373evb/README @@ -89,7 +89,7 @@ MCFFEC_TOUT_LOOP -- set FEC timeout loop CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README index 2b25952398..c70c4c5c25 100644 --- a/board/freescale/m54455evb/README +++ b/board/freescale/m54455evb/README @@ -112,7 +112,7 @@ _IO_BASE -- define for IO base address CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README index 1a8cbce91d..ce497c0d2a 100644 --- a/board/freescale/m547xevb/README +++ b/board/freescale/m547xevb/README @@ -97,7 +97,7 @@ CONFIG_DOS_PARTITION -- enable DOS read/write CONFIG_SLTTMR -- define to use SLT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed diff --git a/board/freescale/mpc8349itx/mpc8349itx.c b/board/freescale/mpc8349itx/mpc8349itx.c index 9cc808ed7d..271768dc76 100644 --- a/board/freescale/mpc8349itx/mpc8349itx.c +++ b/board/freescale/mpc8349itx/mpc8349itx.c @@ -263,8 +263,7 @@ int misc_init_r(void) { int rc = 0; -#ifdef CONFIG_HARD_I2C - +#if defined(CONFIG_SYS_I2C) unsigned int orig_bus = i2c_get_bus_num(); u8 i2c_data; diff --git a/board/freescale/mpc8349itx/pci.c b/board/freescale/mpc8349itx/pci.c index 7d30d9b85f..1ab4e0c689 100644 --- a/board/freescale/mpc8349itx/pci.c +++ b/board/freescale/mpc8349itx/pci.c @@ -87,7 +87,7 @@ void pci_init_board(void) #endif u8 reg8; -#ifdef CONFIG_HARD_I2C +#if defined(CONFIG_SYS_I2C) i2c_set_bus_num(1); /* Read the PCI_M66EN jumper setting */ if ((i2c_read(CONFIG_SYS_I2C_8574_ADDR2, 0, 0, ®8, sizeof(reg8)) == 0) || diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c index 2e0e0c73aa..e4f577f44b 100644 --- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c +++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c @@ -248,7 +248,7 @@ int checkboard(void) in_8(&cpld_data->pcba_rev) & 0x0F); /* Initialize i2c early for rom_loc and flash bank information */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); if (i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 0, 1, &in, 1) < 0 || i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 1, 1, &out, 1) < 0 || diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c index 918a6ab639..a14496f5fb 100644 --- a/board/keymile/common/ivm.c +++ b/board/keymile/common/ivm.c @@ -314,29 +314,13 @@ int ivm_analyze_eeprom(unsigned char *buf, int len) int ivm_read_eeprom(void) { -#if defined(CONFIG_I2C_MUX) - I2C_MUX_DEVICE *dev = NULL; -#endif uchar i2c_buffer[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; char *buf; unsigned long dev_addr = CONFIG_SYS_IVM_EEPROM_ADR; int ret; -#if defined(CONFIG_SYS_I2C) buf = getenv("EEprom_ivm"); i2c_set_bus_num(buf ? (int)simple_strtol(buf, NULL, 10) : 0); -#else -#if defined(CONFIG_I2C_MUX) - /* First init the Bus, select the Bus */ - buf = (unsigned char *) getenv("EEprom_ivm"); - if (buf != NULL) - dev = i2c_mux_ident_muxstring(buf); - if (dev == NULL) { - printf("Error couldnt add Bus for IVM\n"); - return -1; - } - i2c_set_bus_num(dev->busid); -#endif /* add deblocking here */ i2c_make_abort(); diff --git a/board/keymile/km83xx/km83xx.c b/board/keymile/km83xx/km83xx.c index faaa39bc20..6d45809614 100644 --- a/board/keymile/km83xx/km83xx.c +++ b/board/keymile/km83xx/km83xx.c @@ -95,19 +95,6 @@ const qe_iop_conf_t qe_iop_conf_tab[] = { {0, 0, 0, 0, QE_IOP_TAB_END}, }; -static int board_init_i2c_busses(void) -{ - I2C_MUX_DEVICE *dev = NULL; - uchar *dtt_bus = (uchar *)"pca9547:70:a"; - - /* Set up the Bus for the DTTs */ - dev = i2c_mux_ident_muxstring(dtt_bus); - if (dev == NULL) - printf("Error couldn't add Bus for DTT\n"); - - return 0; -} - #if defined(CONFIG_SUVD3) const uint upma_table[] = { 0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */ @@ -206,8 +193,6 @@ int board_early_init_r(void) int misc_init_r(void) { - /* add board specific i2c busses */ - board_init_i2c_busses(); return 0; } diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index a885e26ce9..1202d2454e 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -28,7 +28,6 @@ LIB := $(obj)libi2c.o COBJS-$(CONFIG_BFIN_TWI_I2C) += bfin-twi_i2c.o COBJS-$(CONFIG_DRIVER_DAVINCI_I2C) += davinci_i2c.o COBJS-$(CONFIG_DW_I2C) += designware_i2c.o -COBJS-$(CONFIG_FSL_I2C) += fsl_i2c.o COBJS-$(CONFIG_I2C_MVTWSI) += mvtwsi.o COBJS-$(CONFIG_I2C_MV) += mv_i2c.o COBJS-$(CONFIG_I2C_MXC) += mxc_i2c.o @@ -46,6 +45,7 @@ COBJS-$(CONFIG_U8500_I2C) += u8500_i2c.o COBJS-$(CONFIG_SH_I2C) += sh_i2c.o COBJS-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o COBJS-$(CONFIG_SYS_I2C) += i2c_core.o +COBJS-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o COBJS-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o COBJS-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c index 5d7e010319..38455e1c66 100644 --- a/drivers/i2c/fsl_i2c.c +++ b/drivers/i2c/fsl_i2c.c @@ -1,6 +1,9 @@ /* * Copyright 2006,2009 Freescale Semiconductor, Inc. * + * 2012, Heiko Schocher, DENX Software Engineering, hs@denx.de. + * Changes for multibus/multiadapter I2C support. + * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * Version 2 as published by the Free Software Foundation. @@ -17,12 +20,8 @@ */ #include <common.h> - -#ifdef CONFIG_HARD_I2C - #include <command.h> #include <i2c.h> /* Functional interface */ - #include <asm/io.h> #include <asm/fsl_i2c.h> /* HW definitions */ @@ -47,25 +46,10 @@ DECLARE_GLOBAL_DATA_PTR; -/* Initialize the bus pointer to whatever one the SPD EEPROM is on. - * Default is bus 0. This is necessary because the DDR initialization - * runs from ROM, and we can't switch buses because we can't modify - * the global variables. - */ -#ifndef CONFIG_SYS_SPD_BUS_NUM -#define CONFIG_SYS_SPD_BUS_NUM 0 -#endif -static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = CONFIG_SYS_SPD_BUS_NUM; -#if defined(CONFIG_I2C_MUX) -static unsigned int i2c_bus_num_mux __attribute__ ((section ("data"))) = 0; -#endif - -static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SPEED}; - static const struct fsl_i2c *i2c_dev[2] = { - (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET), -#ifdef CONFIG_SYS_I2C2_OFFSET - (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET) + (struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C_OFFSET), +#ifdef CONFIG_SYS_FSL_I2C2_OFFSET + (struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C2_OFFSET) #endif }; @@ -222,12 +206,9 @@ static unsigned int get_i2c_clock(int bus) return gd->arch.i2c1_clk; /* I2C1 clock */ } -void -i2c_init(int speed, int slaveadd) +static void fsl_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { const struct fsl_i2c *dev; - unsigned int temp; - int bus_num, i; #ifdef CONFIG_SYS_I2C_INIT_BOARD /* Call board specific i2c bus reset routine before accessing the @@ -236,23 +217,14 @@ i2c_init(int speed, int slaveadd) */ i2c_init_board(); #endif -#ifdef CONFIG_SYS_I2C2_OFFSET - bus_num = 2; -#else - bus_num = 1; -#endif - for (i = 0; i < bus_num; i++) { - dev = i2c_dev[i]; - - writeb(0, &dev->cr); /* stop I2C controller */ - udelay(5); /* let it shutdown in peace */ - temp = set_i2c_bus_speed(dev, get_i2c_clock(i), speed); - if (gd->flags & GD_FLG_RELOC) - i2c_bus_speed[i] = temp; - writeb(slaveadd << 1, &dev->adr);/* write slave address */ - writeb(0x0, &dev->sr); /* clear status register */ - writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ - } + dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; + + writeb(0, &dev->cr); /* stop I2C controller */ + udelay(5); /* let it shutdown in peace */ + set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed); + writeb(slaveadd << 1, &dev->adr);/* write slave address */ + writeb(0x0, &dev->sr); /* clear status register */ + writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ #ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT /* Call board specific i2c bus reset routine AFTER the bus has been @@ -265,12 +237,13 @@ i2c_init(int speed, int slaveadd) } static int -i2c_wait4bus(void) +i2c_wait4bus(struct i2c_adapter *adap) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; unsigned long long timeval = get_ticks(); const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT); - while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) { + while (readb(&dev->sr) & I2C_SR_MBB) { if ((get_ticks() - timeval) > timeout) return -1; } @@ -279,20 +252,21 @@ i2c_wait4bus(void) } static __inline__ int -i2c_wait(int write) +i2c_wait(struct i2c_adapter *adap, int write) { u32 csr; unsigned long long timeval = get_ticks(); const unsigned long long timeout = usec2ticks(CONFIG_I2C_TIMEOUT); + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; do { - csr = readb(&i2c_dev[i2c_bus_num]->sr); + csr = readb(&dev->sr); if (!(csr & I2C_SR_MIF)) continue; /* Read again to allow register to stabilise */ - csr = readb(&i2c_dev[i2c_bus_num]->sr); + csr = readb(&dev->sr); - writeb(0x0, &i2c_dev[i2c_bus_num]->sr); + writeb(0x0, &dev->sr); if (csr & I2C_SR_MAL) { debug("i2c_wait: MAL\n"); @@ -317,29 +291,32 @@ i2c_wait(int write) } static __inline__ int -i2c_write_addr (u8 dev, u8 dir, int rsta) +i2c_write_addr(struct i2c_adapter *adap, u8 dev, u8 dir, int rsta) { + struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; + writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX | (rsta ? I2C_CR_RSTA : 0), - &i2c_dev[i2c_bus_num]->cr); + &device->cr); - writeb((dev << 1) | dir, &i2c_dev[i2c_bus_num]->dr); + writeb((dev << 1) | dir, &device->dr); - if (i2c_wait(I2C_WRITE_BIT) < 0) + if (i2c_wait(adap, I2C_WRITE_BIT) < 0) return 0; return 1; } static __inline__ int -__i2c_write(u8 *data, int length) +__i2c_write(struct i2c_adapter *adap, u8 *data, int length) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i; for (i = 0; i < length; i++) { - writeb(data[i], &i2c_dev[i2c_bus_num]->dr); + writeb(data[i], &dev->dr); - if (i2c_wait(I2C_WRITE_BIT) < 0) + if (i2c_wait(adap, I2C_WRITE_BIT) < 0) break; } @@ -347,57 +324,60 @@ __i2c_write(u8 *data, int length) } static __inline__ int -__i2c_read(u8 *data, int length) +__i2c_read(struct i2c_adapter *adap, u8 *data, int length) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i; writeb(I2C_CR_MEN | I2C_CR_MSTA | ((length == 1) ? I2C_CR_TXAK : 0), - &i2c_dev[i2c_bus_num]->cr); + &dev->cr); /* dummy read */ - readb(&i2c_dev[i2c_bus_num]->dr); + readb(&dev->dr); for (i = 0; i < length; i++) { - if (i2c_wait(I2C_READ_BIT) < 0) + if (i2c_wait(adap, I2C_READ_BIT) < 0) break; /* Generate ack on last next to last byte */ if (i == length - 2) writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK, - &i2c_dev[i2c_bus_num]->cr); + &dev->cr); /* Do not generate stop on last byte */ if (i == length - 1) writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX, - &i2c_dev[i2c_bus_num]->cr); + &dev->cr); - data[i] = readb(&i2c_dev[i2c_bus_num]->dr); + data[i] = readb(&dev->dr); } return i; } -int -i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) +static int +fsl_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, int alen, u8 *data, + int length) { + struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i = -1; /* signal error */ u8 *a = (u8*)&addr; - if (i2c_wait4bus() < 0) + if (i2c_wait4bus(adap) < 0) return -1; if ((!length || alen > 0) - && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 - && __i2c_write(&a[4 - alen], alen) == alen) + && i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0 + && __i2c_write(adap, &a[4 - alen], alen) == alen) i = 0; /* No error so far */ if (length && - i2c_write_addr(dev, I2C_READ_BIT, alen ? 1 : 0) != 0) - i = __i2c_read(data, length); + i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0) + i = __i2c_read(adap, data, length); - writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); + writeb(I2C_CR_MEN, &device->cr); - if (i2c_wait4bus()) /* Wait until STOP */ + if (i2c_wait4bus(adap)) /* Wait until STOP */ debug("i2c_read: wait4bus timed out\n"); if (i == length) @@ -406,20 +386,22 @@ i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) return -1; } -int -i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) +static int +fsl_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, int alen, + u8 *data, int length) { + struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i = -1; /* signal error */ u8 *a = (u8*)&addr; - if (i2c_wait4bus() >= 0 - && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 - && __i2c_write(&a[4 - alen], alen) == alen) { - i = __i2c_write(data, length); + if (i2c_wait4bus(adap) >= 0 && + i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0 && + __i2c_write(adap, &a[4 - alen], alen) == alen) { + i = __i2c_write(adap, data, length); } - writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); - if (i2c_wait4bus()) /* Wait until STOP */ + writeb(I2C_CR_MEN, &device->cr); + if (i2c_wait4bus(adap)) /* Wait until STOP */ debug("i2c_write: wait4bus timed out\n"); if (i == length) @@ -428,72 +410,42 @@ i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) return -1; } -int -i2c_probe(uchar chip) +static int +fsl_i2c_probe(struct i2c_adapter *adap, uchar chip) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; /* For unknow reason the controller will ACK when * probing for a slave with the same address, so skip * it. */ - if (chip == (readb(&i2c_dev[i2c_bus_num]->adr) >> 1)) - return -1; - - return i2c_read(chip, 0, 0, NULL, 0); -} - -int i2c_set_bus_num(unsigned int bus) -{ -#if defined(CONFIG_I2C_MUX) - if (bus < CONFIG_SYS_MAX_I2C_BUS) { - i2c_bus_num = bus; - } else { - int ret; - - ret = i2x_mux_select_mux(bus); - if (ret) - return ret; - i2c_bus_num = 0; - } - i2c_bus_num_mux = bus; -#else -#ifdef CONFIG_SYS_I2C2_OFFSET - if (bus > 1) { -#else - if (bus > 0) { -#endif + if (chip == (readb(&dev->adr) >> 1)) return -1; - } - i2c_bus_num = bus; -#endif - return 0; + return fsl_i2c_read(adap, chip, 0, 0, NULL, 0); } -int i2c_set_bus_speed(unsigned int speed) +static unsigned int fsl_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) { - unsigned int i2c_clk = (i2c_bus_num == 1) - ? gd->arch.i2c2_clk : gd->arch.i2c1_clk; + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; - writeb(0, &i2c_dev[i2c_bus_num]->cr); /* stop controller */ - i2c_bus_speed[i2c_bus_num] = - set_i2c_bus_speed(i2c_dev[i2c_bus_num], i2c_clk, speed); - writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); /* start controller */ + writeb(0, &dev->cr); /* stop controller */ + set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed); + writeb(I2C_CR_MEN, &dev->cr); /* start controller */ return 0; } -unsigned int i2c_get_bus_num(void) -{ -#if defined(CONFIG_I2C_MUX) - return i2c_bus_num_mux; -#else - return i2c_bus_num; +/* + * Register fsl i2c adapters + */ +U_BOOT_I2C_ADAP_COMPLETE(fsl_0, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read, + fsl_i2c_write, fsl_i2c_set_bus_speed, + CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE, + 0) +#ifdef CONFIG_SYS_FSL_I2C2_OFFSET +U_BOOT_I2C_ADAP_COMPLETE(fsl_1, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read, + fsl_i2c_write, fsl_i2c_set_bus_speed, + CONFIG_SYS_FSL_I2C2_SPEED, CONFIG_SYS_FSL_I2C2_SLAVE, + 1) #endif -} - -unsigned int i2c_get_bus_speed(void) -{ - return i2c_bus_speed[i2c_bus_num]; -} - -#endif /* CONFIG_HARD_I2C */ diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index a823f9f3a7..43d0e7da83 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -459,14 +459,14 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed in Hz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x119000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 /* * RTC configuration diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h index a3f64408de..15ab6d0a12 100644 --- a/include/configs/BSC9131RDB.h +++ b/include/configs/BSC9131RDB.h @@ -275,12 +275,11 @@ extern unsigned long get_sdram_size(void); #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 /* I2C EEPROM */ #define CONFIG_CMD_EEPROM diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h index 3aa44435a2..7d5a8e6d0f 100644 --- a/include/configs/BSC9132QDS.h +++ b/include/configs/BSC9132QDS.h @@ -451,15 +451,14 @@ combinations. this should be removed later #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400800 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400800 /* I2C speed and slave address*/ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400800 /* I2C speed and slave address*/ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/HWW1U1A.h b/include/configs/HWW1U1A.h index 2b72a33487..0284f45732 100644 --- a/include/configs/HWW1U1A.h +++ b/include/configs/HWW1U1A.h @@ -218,16 +218,16 @@ /* -------------------------------------------------------------------- */ /* Generic FreeScale hardware I2C support */ -#define CONFIG_HARD_I2C -#define CONFIG_FSL_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } #define CONFIG_CMD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 - -/* I2C bus configuration */ -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F /* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */ #define CONFIG_SYS_SPD_BUS_NUM 0 diff --git a/include/configs/M5208EVBE.h b/include/configs/M5208EVBE.h index 209c1223f4..8410d8b795 100644 --- a/include/configs/M5208EVBE.h +++ b/include/configs/M5208EVBE.h @@ -82,11 +82,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M52277EVB.h b/include/configs/M52277EVB.h index b1bdac2d7b..4275088208 100644 --- a/include/configs/M52277EVB.h +++ b/include/configs/M52277EVB.h @@ -145,11 +145,11 @@ #undef CONFIG_MCFPIT /* I2c */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* DSPI and Serial Flash */ diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h index dfc2ddf35d..3ba4d14a74 100644 --- a/include/configs/M5235EVB.h +++ b/include/configs/M5235EVB.h @@ -99,11 +99,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_i2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_SYS_I2C_PINMUX_REG (gpio->par_qspi) #define CONFIG_SYS_I2C_PINMUX_CLR ~(GPIO_PAR_FECI2C_SCL_MASK | GPIO_PAR_FECI2C_SDA_MASK) diff --git a/include/configs/M5253DEMO.h b/include/configs/M5253DEMO.h index fe1cca50e1..eb375f0385 100644 --- a/include/configs/M5253DEMO.h +++ b/include/configs/M5253DEMO.h @@ -114,11 +114,11 @@ #define CONFIG_HOSTNAME M5253DEMO /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000280 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C)) #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF) diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h index e8a8998fcc..9ca850eb47 100644 --- a/include/configs/M5271EVB.h +++ b/include/configs/M5271EVB.h @@ -109,11 +109,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */ diff --git a/include/configs/M5275EVB.h b/include/configs/M5275EVB.h index fbf0c9d9ac..9d2dfa0a06 100644 --- a/include/configs/M5275EVB.h +++ b/include/configs/M5275EVB.h @@ -109,11 +109,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_SYS_I2C_PINMUX_REG (gpio_reg->par_feci2c) #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFF0) diff --git a/include/configs/M53017EVB.h b/include/configs/M53017EVB.h index bedba2b290..4bb693a738 100644 --- a/include/configs/M53017EVB.h +++ b/include/configs/M53017EVB.h @@ -101,11 +101,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h index 06fa57cc02..23ee61e4da 100644 --- a/include/configs/M5329EVB.h +++ b/include/configs/M5329EVB.h @@ -95,11 +95,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M5373EVB.h b/include/configs/M5373EVB.h index faa4f86e43..bbfef903c9 100644 --- a/include/configs/M5373EVB.h +++ b/include/configs/M5373EVB.h @@ -95,11 +95,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h index 627c1ae005..817d79ee2f 100644 --- a/include/configs/M54418TWR.h +++ b/include/configs/M54418TWR.h @@ -213,7 +213,7 @@ #undef CONFIG_MCFPIT /* I2c */ -#undef CONFIG_FSL_I2C +#undef CONFIG_SYS_FSL_I2C #undef CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ /* I2C speed and slave address */ diff --git a/include/configs/M54451EVB.h b/include/configs/M54451EVB.h index 5dbe0b47c1..85cd46416a 100644 --- a/include/configs/M54451EVB.h +++ b/include/configs/M54451EVB.h @@ -156,11 +156,11 @@ #undef CONFIG_MCFPIT /* I2c */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* DSPI and Serial Flash */ diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index 8246e68e46..aa7e9f8327 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -189,11 +189,11 @@ #undef CONFIG_MCFPIT /* I2c */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSLI2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* DSPI and Serial Flash */ diff --git a/include/configs/M5475EVB.h b/include/configs/M5475EVB.h index 6e9cba00a7..5377a51251 100644 --- a/include/configs/M5475EVB.h +++ b/include/configs/M5475EVB.h @@ -120,11 +120,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00008F00 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* PCI */ diff --git a/include/configs/M5485EVB.h b/include/configs/M5485EVB.h index 24f28e0ff5..316e07c0ad 100644 --- a/include/configs/M5485EVB.h +++ b/include/configs/M5485EVB.h @@ -117,11 +117,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00008F00 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* PCI */ diff --git a/include/configs/MERGERBOX.h b/include/configs/MERGERBOX.h index 2496639512..0f17411b03 100644 --- a/include/configs/MERGERBOX.h +++ b/include/configs/MERGERBOX.h @@ -224,13 +224,14 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 120000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h index f10555ce01..44caa59894 100644 --- a/include/configs/MPC8308RDB.h +++ b/include/configs/MPC8308RDB.h @@ -350,14 +350,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * SPI on header J8 diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 1d753e76b9..e6c60b3c93 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -403,14 +403,15 @@ #define CONFIG_SYS_HUSH_PARSER /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * General PCI diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index ee806c4403..2f5addc3ce 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -347,13 +347,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave addr */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Board info - revision and where boot from diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index d32b14a105..d5db65df11 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -233,12 +233,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board EEPROM diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index a35c6b6d84..beee1904ef 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -326,12 +326,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board RTC diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 7c3f35c3af..754a9eb335 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -354,14 +354,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* SPI */ #define CONFIG_MPC8XXX_SPI diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index c67ffdba0f..0d5a026582 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -90,7 +90,7 @@ #define CONFIG_PCI #define CONFIG_RTC_DS1337 -#define CONFIG_HARD_I2C +#define CONFIG_SYS_I2C #define CONFIG_TSEC_ENET /* TSEC Ethernet support */ /* @@ -98,12 +98,15 @@ */ /* I2C */ -#ifdef CONFIG_HARD_I2C +#ifdef CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_SYS_SPD_BUS_NUM 1 /* The I2C bus for SPD */ #define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ @@ -115,9 +118,6 @@ #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/ #define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - /* Don't probe these addresses: */ #define CONFIG_SYS_I2C_NOPROBES { {1, CONFIG_SYS_I2C_8574_ADDR1}, \ {1, CONFIG_SYS_I2C_8574_ADDR2}, \ @@ -197,7 +197,7 @@ #define CONFIG_VERY_BIG_RAM #define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20) -#ifdef CONFIG_HARD_I2C +#ifdef CONFIG_SYS_I2C #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ #endif @@ -543,7 +543,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CONFIG_CMD_PCI #endif -#ifdef CONFIG_HARD_I2C +#ifdef CONFIG_SYS_I2C #define CONFIG_CMD_I2C #endif diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index 4d6486bb30..2b7af86690 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -423,13 +423,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x52} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* * Config on-board RTC diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h index 29e77195de..f189039e86 100644 --- a/include/configs/MPC8360ERDK.h +++ b/include/configs/MPC8360ERDK.h @@ -287,14 +287,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* * General PCI diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 91c8a34859..cb0863dd91 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -341,13 +341,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board RTC diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index 3279e3cf6f..d014e6814e 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -367,13 +367,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board RTC diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index f560b56d46..052fb54441 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -434,14 +434,15 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } /* * I2C2 EEPROM diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index a42dec4ed8..25638ac484 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -260,12 +260,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* RapidIO MMU */ #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 13011b5a87..a486347dbc 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -283,12 +283,12 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index b00468eb8b..48a3ea1702 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -232,13 +232,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 50e318c5d6..2a1de524dc 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -358,12 +358,12 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 388ba9ba1e..d4a395f608 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -281,12 +281,12 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index 04f6a656e6..7a6231192f 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -254,12 +254,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* RapidIO MMU */ #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 05a69af6ae..6cda16b64f 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -266,15 +266,16 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 23bd90880a..e36aadee8f 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -302,14 +302,15 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * I2C2 EEPROM diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index 45abcf61de..f794fdb0ae 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -431,15 +431,16 @@ #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 0a2e39b118..1553a746c8 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -252,12 +252,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * General PCI diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 3ac5b2beb1..6d6058f5ef 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -298,12 +298,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * RapidIO MMU diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h index afd4c0356d..8342a1a7e1 100644 --- a/include/configs/MVBLM7.h +++ b/include/configs/MVBLM7.h @@ -44,7 +44,6 @@ #define CONFIG_PCI #define CONFIG_PCI_INDIRECT_BRIDGE #define CONFIG_PCI_SKIP_HOST_BRIDGE -#define CONFIG_HARD_I2C #define CONFIG_TSEC_ENET #define CONFIG_MPC8XXX_SPI #define CONFIG_HARD_SPI @@ -52,13 +51,14 @@ #define CONFIG_MISC_INIT_R /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 - -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * DDR Setup diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index ed1a42916d..ba0a396cee 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -489,14 +489,15 @@ extern unsigned long get_sdram_size(void); #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C EEPROM */ #undef CONFIG_ID_EEPROM diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index 9c27182dc7..40076471ac 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -361,15 +361,15 @@ #define CONFIG_FIT_VERBOSE /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h index fee8040e2d..f21d9e860b 100644 --- a/include/configs/P1023RDB.h +++ b/include/configs/P1023RDB.h @@ -204,13 +204,14 @@ extern unsigned long get_clock_freq(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h index f6ee2515a3..7e2679bd2f 100644 --- a/include/configs/P1023RDS.h +++ b/include/configs/P1023RDS.h @@ -313,14 +313,15 @@ extern unsigned long get_clock_freq(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x51 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 699e9ebcda..b86637cd8b 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -367,15 +367,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } /* * I2C2 EEPROM diff --git a/include/configs/P2020COME.h b/include/configs/P2020COME.h index c8f5a85ded..3266e54134 100644 --- a/include/configs/P2020COME.h +++ b/include/configs/P2020COME.h @@ -225,15 +225,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FIT_VERBOSE 1 /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index 229117c18d..94b77d1dc7 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -387,15 +387,16 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } /* * I2C2 EEPROM diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index 4ea8717368..2c2b609b1a 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -367,14 +367,14 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * RapidIO diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h index 318c4c5d51..e127d6f13f 100644 --- a/include/configs/SIMPC8313.h +++ b/include/configs/SIMPC8313.h @@ -245,14 +245,15 @@ #define CONFIG_SYS_HUSH_PARSER /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * General PCI diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index f22eb35c2f..89b6db6cf9 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -187,11 +187,11 @@ /* * I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed: 400KHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 /* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h index 6dabe57e7c..f641959cc1 100644 --- a/include/configs/astro_mcf5373l.h +++ b/include/configs/astro_mcf5373l.h @@ -116,11 +116,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* diff --git a/include/configs/controlcenterd.h b/include/configs/controlcenterd.h index cdd79f0769..c6aad01dba 100644 --- a/include/configs/controlcenterd.h +++ b/include/configs/controlcenterd.h @@ -192,15 +192,14 @@ /* * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_CMD_I2C - -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* Probing DP501 I2C-Bridge will hang */ #define CONFIG_SYS_I2C_NOPROBES { {0, 0x30}, {0, 0x37}, {0, 0x3a}, \ {0, 0x3b}, {0, 0x50} } diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index 66c7b4f95f..41f33d964c 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -362,14 +362,14 @@ #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 /* * RapidIO diff --git a/include/configs/eb_cpu5282.h b/include/configs/eb_cpu5282.h index 459f56878c..6e734df569 100644 --- a/include/configs/eb_cpu5282.h +++ b/include/configs/eb_cpu5282.h @@ -262,14 +262,14 @@ * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_FSL_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0 +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0 #ifdef CONFIG_CMD_DATE #define CONFIG_RTC_DS1338 diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h index 5a430edbc3..a6f8ebd9de 100644 --- a/include/configs/km/km83xx-common.h +++ b/include/configs/km/km83xx-common.h @@ -204,14 +204,21 @@ #endif /* CFG_SYS_RAMBOOT */ /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_MAX_I2C_BUS 1 -#define CONFIG_I2C_MUX +#define CONFIG_SYS_I2C +#define CONFIG_SYS_NUM_I2C_BUSES 4 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 200000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 200000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ + {1, {I2C_NULL_HOP} } } /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 /* ON Semi's LM75 */ @@ -219,7 +226,7 @@ #define CONFIG_SYS_DTT_MAX_TEMP 70 #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) +#define CONFIG_SYS_DTT_BUS_NUM 1 #if defined(CONFIG_CMD_NAND) #define CONFIG_NAND_KMETER1 @@ -315,7 +322,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_KM_DEF_ENV \ CONFIG_KM_DEF_ARCH \ - "EEprom_ivm=pca9547:70:9\0" \ + "EEprom_ivm=2\0" \ "newenv=" \ "prot off 0xF00C0000 +0x40000 && " \ "era 0xF00C0000 +0x40000\0" \ diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h index 3c7a85e359..517d6f3dcb 100644 --- a/include/configs/mpc8308_p1m.h +++ b/include/configs/mpc8308_p1m.h @@ -327,13 +327,14 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/mpq101.h b/include/configs/mpq101.h index 339c736311..8ca3f76f03 100644 --- a/include/configs/mpq101.h +++ b/include/configs/mpq101.h @@ -221,13 +221,15 @@ /* * I2C buses and peripherals */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7f -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* I2C RTC - M41T81 */ #define CONFIG_RTC_M41T62 diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index d0a6b1757f..1d1ad3debf 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -534,16 +534,16 @@ #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C spd and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} /* Don't probe this addr */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ /* diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index 7a79e8c212..9925d30341 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -304,14 +304,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C1_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69}, {1, 0x69} } /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ /* TSEC */ diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 354691a364..e700436c53 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -444,12 +444,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 /* * General PCI diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 147e0ae83a..b83658de8e 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -289,12 +289,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * RapidIO MMU diff --git a/include/configs/socrates.h b/include/configs/socrates.h index 19869e613a..f1323eca2a 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -235,14 +235,14 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 102124 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 - -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 102124 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 102124 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C RTC */ #define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */ diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index b688b457d6..d7c079740e 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -178,17 +178,18 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 + #if 0 #define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */ #else /* I did the 'if 0' so we could keep the syntax above if ever needed. */ #undef CONFIG_SYS_I2C_NOPROBES #endif -#define CONFIG_SYS_I2C_OFFSET 0x3000 /* RapdIO Map configuration, mapped 1:1. */ diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 4c3c08622a..3e3ede42d7 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -198,12 +198,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 #undef CONFIG_SYS_I2C_NOPROBES -#define CONFIG_SYS_I2C_OFFSET 0x3000 /* I2C RTC */ #define CONFIG_RTC_DS1337 /* This is really a DS1339 RTC */ diff --git a/include/configs/t4qds.h b/include/configs/t4qds.h index 92b2179ca7..f7999fce0d 100644 --- a/include/configs/t4qds.h +++ b/include/configs/t4qds.h @@ -445,14 +445,15 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 + #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ #define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */ diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h index 54fbe8bdad..222f4ce2d4 100644 --- a/include/configs/vme8349.h +++ b/include/configs/vme8349.h @@ -237,16 +237,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS /* I2C */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C1_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C1_OFFSET +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ #define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */ diff --git a/include/configs/xpedite517x.h b/include/configs/xpedite517x.h index f28f443fe9..719a4904d4 100644 --- a/include/configs/xpedite517x.h +++ b/include/configs/xpedite517x.h @@ -258,13 +258,14 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 100000 /* M41T00 only supports 100 KHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* PEX8518 slave I2C interface */ #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h index 3034a3c9a9..e55635c9d6 100644 --- a/include/configs/xpedite520x.h +++ b/include/configs/xpedite520x.h @@ -220,13 +220,14 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h index 43359a2eef..bdfe0baa58 100644 --- a/include/configs/xpedite537x.h +++ b/include/configs/xpedite537x.h @@ -258,13 +258,15 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* PEX8518 slave I2C interface */ #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h index a171085354..a8be3f62ab 100644 --- a/include/configs/xpedite550x.h +++ b/include/configs/xpedite550x.h @@ -249,13 +249,14 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C DS7505 temperature sensor */ #define CONFIG_DTT_LM75 |
