Merge with /home/wd/git/u-boot/custodian/u-boot-mpc85xx

8 files changed, 1137 insertions, 21 deletions

diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h
index b226825ee2..48fd982950 100644
--- a/include/asm-ppc/mmu.h
+++ b/include/asm-ppc/mmu.h
@@ -396,8 +396,8 @@ extern int write_bat(ppc_bat_t bat, unsigned long upper, unsigned long lower);
 #define BOOKE_PAGESZ_16M        7
 #define BOOKE_PAGESZ_64M        8
 #define BOOKE_PAGESZ_256M       9
-#define BOOKE_PAGESZ_1GB        10
-#define BOOKE_PAGESZ_4GB        11
+#define BOOKE_PAGESZ_1G		10
+#define BOOKE_PAGESZ_4G		11
 
 #if defined(CONFIG_MPC86xx)
 #define LAWBAR_BASE_ADDR	0x00FFFFFF
@@ -413,6 +413,7 @@ extern int write_bat(ppc_bat_t bat, unsigned long upper, unsigned long lower);
 #define LAWAR_TRGT_IF_PCI1	0x00000000
 #define LAWAR_TRGT_IF_PCIX	0x00000000
 #define LAWAR_TRGT_IF_PCI2	0x00100000
+#define LAWAR_TRGT_IF_PEX	0x00200000
 #define LAWAR_TRGT_IF_LBC	0x00400000
 #define LAWAR_TRGT_IF_CCSR	0x00800000
 #define LAWAR_TRGT_IF_DDR_INTERLEAVED 0x00B00000
diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h
index 058596275f..e9361c5174 100644
--- a/include/asm-ppc/processor.h
+++ b/include/asm-ppc/processor.h
@@ -232,6 +232,9 @@
 #define   HID0_BHTE	(1<<2)		/* Branch History Table Enable */
 #define   HID0_BTCD	(1<<1)		/* Branch target cache disable */
 #define SPRN_HID1	0x3F1	/* Hardware Implementation Register 1 */
+#define	  HID1_RFXE	(1<<17)		/* Read Fault Exception Enable */
+#define	  HID1_ASTME	(1<<13)		/* Address bus streaming mode */
+#define	  HID1_ABE	(1<<12)		/* Address broadcast enable */
 #define SPRN_IABR	0x3F2	/* Instruction Address Breakpoint Register */
 #ifndef CONFIG_BOOKE
 #define SPRN_IAC1	0x3F4	/* Instruction Address Compare 1 */
@@ -415,10 +418,12 @@
 #define SPRN_IVOR15	0x19f	/* Interrupt Vector Offset Register 15 */
 
 /* e500 definitions */
-#define SPRN_L1CSR0     0x3f2   /* L1 Cache Control and Status Register 0 */
+#define SPRN_L1CSR0     0x3f2   /* L1 Data Cache Control and Status Register 0 */
+#define   L1CSR0_CPE            0x00010000	/* Data Cache Parity Enable */
 #define   L1CSR0_DCFI           0x00000002      /* Data Cache Flash Invalidate */
 #define   L1CSR0_DCE            0x00000001      /* Data Cache Enable */
-#define SPRN_L1CSR1     0x3f3   /* L1 Cache Control and Status Register 1 */
+#define SPRN_L1CSR1     0x3f3   /* L1 Instruction Cache Control and Status Register 1 */
+#define   L1CSR1_CPE            0x00010000	/* Instruction Cache Parity Enable */
 #define   L1CSR1_ICFI           0x00000002      /* Instruction Cache Flash Invalidate */
 #define   L1CSR1_ICE            0x00000001      /* Instruction Cache Enable */
 
@@ -840,9 +845,12 @@
 #define SVR_8560	0x8070
 #define SVR_8555	0x8079
 #define SVR_8541	0x807A
+#define SVR_8544	0x8034
+#define SVR_8544_E	0x803C
 #define SVR_8548	0x8031
 #define SVR_8548_E	0x8039
 #define SVR_8641	0x8090
+#define SVR_8568_E	0x807D
 
 
 /* I am just adding a single entry for 8260 boards.  I think we may be
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 74a84f4e86..5aeea58680 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -330,13 +330,12 @@
 
 /*
  * General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
 #define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
-
-#define CFG_PCI1_IO_BASE	0x0
+#define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xe2000000
 #define CFG_PCI1_IO_SIZE	0x100000	/* 1M */
 
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index db389cfe67..fb360d282c 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -334,7 +334,7 @@ extern unsigned long get_clock_freq(void);
 
 /*
  * General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
new file mode 100644
index 0000000000..4c3430897d
--- /dev/null
+++ b/include/configs/MPC8544DS.h
@@ -0,0 +1,591 @@
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8544ds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8544		1
+#define CONFIG_MPC8544DS	1
+
+#undef CONFIG_PCI			/* Enable PCI/PCIE */
+#undef CONFIG_PCI1			/* PCI controller 1 */
+#undef CONFIG_PCIE1			/* PCIE controler 1 (slot 1) */
+#undef CONFIG_PCIE2			/* PCIE controler 2 (slot 2) */
+#undef CONFIG_PCIE3			/* PCIE controler 3 (ULI bridge) */
+#undef CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_DLL
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
+#define CONFIG_DDR_ECC_CMD
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache 	*/
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+#define CONFIG_CLEAR_LAW0		/* Clear LAW0 in cpu_init_r */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST			/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00200000	/* memtest works on */
+#define CFG_MEMTEST_END		0x00400000
+#define CFG_ALT_MEMTEST
+#define CONFIG_PANIC_HANG 	/* do not reset board on panic */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+#define CFG_PCI1_ADDR		(CFG_CCSRBAR+0x8000)
+#define CFG_PCIE1_ADDR		(CFG_CCSRBAR+0xa000)
+#define CFG_PCIE2_ADDR		(CFG_CCSRBAR+0x9000)
+#define CFG_PCIE3_ADDR		(CFG_CCSRBAR+0xb000)
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+ *
+ * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
+ *
+ * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
+ *
+ * 0xe000_0000	0xe00f_ffff	CCSR			1M non-cacheable
+ * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
+ *
+ * Localbus cacheable
+ *
+ * 0xf000_0000	0xf3ff_ffff	SDRAM			64M Cacheable
+ * 0xf401_0000	0xf401_3fff	L1 for stack		4K Cacheable TLB0
+ *
+ * Localbus non-cacheable
+ *
+ * 0xf800_0000	0xf80f_ffff	NVRAM/CADMUS (*)	1M non-cacheable
+ * 0xff00_0000	0xff7f_ffff	FLASH (2nd bank)	8M non-cacheable
+ * 0xff80_0000	0xffff_ffff	FLASH (boot bank)	8M non-cacheable
+ *
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CFG_BOOT_BLOCK		0xfc000000	/* boot TLB */
+
+#define CFG_LBC_CACHE_BASE	0xf0000000	/* Localbus cacheable */
+
+#define CFG_FLASH_BASE		0xff800000	/* start of FLASH 8M */
+
+#define CFG_BR0_PRELIM		0xff801001
+#define CFG_BR1_PRELIM		0xfe801001
+
+#define CFG_OR0_PRELIM		0xff806e65
+#define CFG_OR1_PRELIM		0xff806e65
+
+#define CFG_FLASH_BANKS_LIST	{0xfe800000,CFG_FLASH_BASE}
+
+#define CFG_MAX_FLASH_BANKS	2		/* number of banks */
+#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#define CFG_LBC_NONCACHE_BASE	0xf8000000
+
+#define CFG_BR2_PRELIM		0xf8201001	/* port size 16bit */
+#define CFG_OR2_PRELIM		0xfff06ff7	/* 1MB Compact Flash area*/
+
+#define CFG_BR3_PRELIM		0xf8100801	/* port size 8bit */
+#define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
+
+#define PIXIS_BASE	0xf8100000	/* PIXIS registers */
+#define PIXIS_ID		0x0	/* Board ID at offset 0 */
+#define PIXIS_VER		0x1	/* Board version at offset 1 */
+#define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
+#define PIXIS_RST		0x4	/* PIXIS Reset Control register */
+#define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch
+					 * register */
+#define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
+#define PIXIS_VCTL		0x10	/* VELA Control Register */
+#define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
+#define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
+#define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
+#define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
+#define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
+#define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM	1
+#define CFG_INIT_L1_LOCK	1
+#define CFG_INIT_L1_ADDR	0xf4010000	/* Initial L1 address */
+#define CFG_INIT_L1_END		0x00004000	/* End of used area in RAM */
+
+/* define to use L2SRAM as initial stack */
+#undef CONFIG_L2_INIT_RAM
+#define CFG_INIT_L2_ADDR	0xf8fc0000
+#define CFG_INIT_L2_END		0x00040000	/* End of used area in RAM */
+
+#ifdef CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_ADDR	CFG_INIT_L1_ADDR
+#define CFG_INIT_RAM_END	CFG_INIT_L1_END
+#else
+#define CFG_INIT_RAM_ADDR	CFG_INIT_L2_ADDR
+#define CFG_INIT_RAM_END	CFG_INIT_L2_END
+#endif
+
+#define CFG_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE	8192
+
+#define OF_CPU			"PowerPC,8544@0"
+#define OF_SOC			"soc8544@e0000000"
+#define OF_TBCLK		(bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH		"/soc8544@e0000000/serial@4500"
+
+/* I2C */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET		0x3100
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CFG_PCIE_PHYS		0x80000000	/* 1G PCIE TLB */
+#define CFG_PCI_PHYS		0xc0000000	/* 512M PCI TLB */
+
+#define CFG_PCI1_MEM_BASE	0xc0000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_IO_BASE	0x00000000
+#define CFG_PCI1_IO_PHYS	0xe1000000
+#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS	0x00000000
+#define CFG_PCI_MEMORY_PHYS	0x00000000
+#define CFG_PCI_MEMORY_SIZE	0x80000000
+
+/* controller 2, Slot 1, tgtid 1, Base address 9000 */
+#define CFG_PCIE2_MEM_BASE	0x80000000
+#define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
+#define CFG_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCIE2_IO_BASE	0x00000000
+#define CFG_PCIE2_IO_PHYS	0xe2000000
+#define CFG_PCIE2_IO_SIZE	0x00100000	/* 1M */
+
+/* controller 1, Slot 2,tgtid 2, Base address a000 */
+#define CFG_PCIE1_MEM_BASE	0xa0000000
+#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE	0x08000000	/* 128M */
+#define CFG_PCIE1_MEM_BASE2	0xa8000000
+#define CFG_PCIE1_MEM_PHYS2	CFG_PCIE1_MEM_BASE2
+#define CFG_PCIE1_MEM_SIZE2	0x04000000	/* 64M */
+#define CFG_PCIE1_IO_BASE	0x00000000	/* reuse mem LAW */
+#define CFG_PCIE1_IO_PHYS	0xaf000000
+#define CFG_PCIE1_IO_SIZE	0x00100000	/* 1M */
+
+/* controller 3, direct to uli, tgtid 3, Base address b000 */
+#define CFG_PCIE3_MEM_BASE	0xb0000000
+#define CFG_PCIE3_MEM_PHYS	CFG_PCIE3_MEM_BASE
+#define CFG_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCIE3_IO_BASE	0x00000000
+#define CFG_PCIE3_IO_PHYS	0xe3000000
+#define CFG_PCIE3_IO_SIZE	0x00100000	/* 1M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#define CONFIG_RTL8139
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x)		(x)
+#define _IO_BASE	0x00000000
+#endif
+
+#ifndef CONFIG_PCI_PNP
+	#define PCI_ENET0_IOADDR	CFG_PCI1_IO_BASE
+	#define PCI_ENET0_MEMADDR	CFG_PCI1_IO_BASE
+	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID	4
+#define CFG_SCSI_MAX_LUN	1
+#define CFG_SCSI_MAX_DEVICE 	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
+#endif /* SCSCI */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"eTSEC1"
+#define CONFIG_MPC85XX_TSEC3	1
+#define CONFIG_MPC85XX_TSEC3_NAME	"eTSEC3"
+#undef CONFIG_MPC85XX_FEC
+
+#define TSEC1_PHY_ADDR		0
+#define TSEC3_PHY_ADDR		1
+
+#define TSEC1_PHYIDX		0
+#define TSEC3_PHYIDX		0
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#if CFG_MONITOR_BASE > 0xfff80000
+#define CFG_ENV_ADDR		0xfff80000
+#else
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#endif
+#define CFG_ENV_SIZE		0x2000
+#define CFG_ENV_SECT_SIZE	0x10000 /* 64K (one sector) */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#if defined(CONFIG_PCI)
+#define	CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PCI \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII \
+				| CFG_CMD_BEDBUG \
+				| CFG_CMD_NET)
+#else
+#define	CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#endif
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE	32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR	00:E0:0C:02:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR	00:E0:0C:02:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR	00:E0:0C:02:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR	00:E0:0C:02:03:FD
+#endif
+
+#define CONFIG_IPADDR	192.168.1.251
+
+#define CONFIG_HOSTNAME	8544ds_unknown
+#define CONFIG_ROOTPATH	/nfs/mpc85xx
+#define CONFIG_BOOTFILE	8544ds_tmt/uImage.uboot
+
+#define CONFIG_SERVERIP	192.168.0.1
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_NETMASK	255.255.0.0
+
+#define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef	CONFIG_BOOTARGS	/* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE	115200
+
+#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
+#define PCIE_ENV \
+ "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
+	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
+ "pcie1regs=setenv a e000a; run pciereg\0"	\
+ "pcie2regs=setenv a e0009; run pciereg\0"	\
+ "pcie3regs=setenv a e000b; run pciereg\0"	\
+ "pcieerr=md ${a}020 1; md ${a}e00;"		\
+	"pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"	\
+	"pci d.w $b.0 56 1;"			\
+	"pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \
+ "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;"	\
+	"pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \
+	"pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \
+	"pci w $b.0 130 ffffffff\0" \
+ "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"	\
+ "pcie1err=setenv a e000a; run pcieerr\0"	\
+ "pcie2err=setenv a e0009; run pcieerr\0"	\
+ "pcie3err=setenv a e000b; run pcieerr\0"	\
+ "pcie1errc=setenv a e000a; run pcieerrc\0"	\
+ "pcie2errc=setenv a e0009; run pcieerrc\0"	\
+ "pcie3errc=setenv a e000b; run pcieerrc\0"
+#else
+#define	PCIE_ENV ""
+#endif
+
+#if defined(CONFIG_PCI1)
+#define PCI_ENV \
+ "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
+	"echo e;md ${a}e00 9\0" 		\
+ "pci1regs=setenv a e0008; run pcireg\0"	\
+ "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
+	"pci d.w $b.0 56 1\0"			\
+ "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
+	"pci w.w $b.0 56 ffff\0"		\
+ "pci1err=setenv a e0008; run pcierr\0"		\
+ "pci1errc=setenv a e0008; run pcierrc\0"
+#else
+#define	PCI_ENV ""
+#endif
+
+#if defined(CONFIG_TSEC_ENET)
+#define ENET_ENV \
+ "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
+	"md ${a}098 2\0" \
+ "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \
+ "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \
+ "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
+	"echo mib;md ${a}680 31\0" \
+ "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
+ "enet1regs=setenv a e0024; run enetreg\0" \
+ "enet3regs=setenv a e0026; run enetreg\0"
+#else
+#define ENET_ENV ""
+#endif
+
+#define	CONFIG_EXTRA_ENV_SETTINGS		\
+ "netdev=eth0\0"				\
+ "consoledev=ttyS0\0"				\
+ "ramdiskaddr=2000000\0"			\
+ "ramdiskfile=8544ds_tmt/ramdisk.uboot\0"	\
+ "fdtaddr=400000\0"				\
+ "fdtfile=8544ds_tmt/mpc8544ds.dtb\0"		\
+ "eoi=mw e00400b0 0\0" 				\
+ "iack=md e00400a0 1\0" 			\
+ "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
+	"md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
+ "ddrregs=setenv a e0002; run ddrreg\0" 	\
+ "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
+	"md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0" 	\
+ "guregs=setenv a e00e0; run gureg\0" 		\
+ "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
+ "ecmregs=setenv a e0001; run ecmreg\0" 	\
+ PCIE_ENV 	\
+ PCI_ENV 	\
+ ENET_ENV
+
+
+#define CONFIG_NFSBOOTCOMMAND		\
+ "setenv bootargs root=/dev/nfs rw "	\
+ "nfsroot=$serverip:$rootpath "		\
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND 		\
+ "setenv bootargs root=/dev/ram rw "	\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $ramdiskaddr $ramdiskfile;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND 		\
+ "setenv bootargs root=/dev/sda3 rw "	\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "tftp $loadaddr $bootfile;"		\
+ "tftp $fdtaddr $fdtfile;"		\
+ "bootm $loadaddr - $fdtaddr"
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 7c4849fadf..680009d600 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -36,12 +36,12 @@
 #define CONFIG_MPC8548		1	/* MPC8548 specific */
 #define CONFIG_MPC8548CDS	1	/* MPC8548CDS board specific */
 
-#undef CONFIG_PCI
+#define CONFIG_PCI
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+#undef CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
 #define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
@@ -340,22 +340,34 @@ extern unsigned long get_clock_freq(void);
 
 /*
  * General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
 #define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xe2000000
-#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCI1_IO_SIZE	0x00800000	/* 8M */
 
-#define CFG_PCI2_MEM_BASE	0xa0000000
+#define CFG_PCI2_MEM_BASE	0x90000000
 #define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI2_MEM_SIZE	0x10000000	/* 256M */
 #define CFG_PCI2_IO_BASE	0x00000000
-#define CFG_PCI2_IO_PHYS	0xe2100000
-#define CFG_PCI2_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCI2_IO_PHYS	0xe2800000
+#define CFG_PCI2_IO_SIZE	0x00800000	/* 8M */
 
+#define CFG_PEX_MEM_BASE	0xa0000000
+#define CFG_PEX_MEM_PHYS	CFG_PEX_MEM_BASE
+#define CFG_PEX_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PEX_IO_BASE		0x00000000
+#define CFG_PEX_IO_PHYS		0xe3000000
+#define CFG_PEX_IO_SIZE		0x01000000	/* 16M */
+
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE	0xC0000000
+#define CFG_RIO_MEM_SIZE	0x20000000	/* 512M */
 
 #if defined(CONFIG_PCI)
 
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 835bf5cb64..21e6637680 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -320,14 +320,14 @@
 
 /*
  * General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
 #define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CFG_PCI1_IO_BASE	0xe2000000
-#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */
+#define CFG_PCI1_IO_BASE	0x00000000
+#define CFG_PCI1_IO_PHYS	0xe2000000
+#define CFG_PCI1_IO_SIZE	0x100000	/* 1M */
 
 #if defined(CONFIG_PCI)
 
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
new file mode 100644
index 0000000000..66293c5221
--- /dev/null
+++ b/include/configs/MPC8568MDS.h
@@ -0,0 +1,505 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8568mds board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500			1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48/68 */
+#define CONFIG_MPC8568		1	/* MPC8568 specific */
+#define CONFIG_MPC8568MDS	1	/* MPC8568MDS board specific */
+
+#undef CONFIG_PCI
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_DLL			/* possible DLL fix needed */
+/*#define CONFIG_DDR_2T_TIMING		 Sets the 2T timing bit */
+
+/*#define CONFIG_DDR_ECC*/			/* only for ECC DDR module */
+/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/	/* 	 DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the MDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_clock_freq(void);
+#endif						  /*Replace a call to get_clock_freq (after it is implemented)*/
+#define CONFIG_SYS_CLK_FREQ	66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+/*#define CONFIG_L2_CACHE*/		    	    /* toggle L2 cache 	*/
+#define CONFIG_BTB						/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST			/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00200000	/* memtest works on */
+#define CFG_MEMTEST_END		0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, 8M each, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff00_0000
+ * Alternate BR1/OR1 bank at 0xff80_0000
+ *
+ * BR0, BR1:
+ *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
+ *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
+ *    Port Size = 16 bits = BRx[19:20] = 10
+ *    Use GPCM = BRx[24:26] = 000
+ *    Valid = BRx[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
+ *
+ * OR0, OR1:
+ *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
+ *    Reserved ORx[17:18] = 11, confusion here?
+ *    CSNT = ORx[20] = 1
+ *    ACS = half cycle delay = ORx[21:22] = 11
+ *    SCY = 6 = ORx[24:27] = 0110
+ *    TRLX = use relaxed timing = ORx[29] = 1
+ *    EAD = use external address latch delay = OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
+ */
+#define CFG_BCSR_BASE		0xf8000000
+
+#define CFG_FLASH_BASE		0xfe000000	/* start of FLASH 32M */
+
+/*Chip select 0 - Flash*/
+#define CFG_BR0_PRELIM		0xfe001001
+#define	CFG_OR0_PRELIM		0xfe006ff7
+
+/*Chip slelect 1 - BCSR*/
+#define CFG_BR1_PRELIM		0xf8000801
+#define	CFG_OR1_PRELIM		0xffffe9f7
+
+//#define CFG_FLASH_BANKS_LIST	{0xff800000, CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS		1		/* number of banks */
+#define CFG_MAX_FLASH_SECT		512		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+
+/*
+ * SDRAM on the LocalBus
+ */
+#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM	 */
+#define CFG_LBC_SDRAM_SIZE	64			/* LBC SDRAM is 64MB */
+
+
+/*Chip select 2 - SDRAM*/
+#define CFG_BR2_PRELIM      0xf0001861
+#define CFG_OR2_PRELIM		0xfc006901
+
+#define CFG_LBC_LCRR		0x00030004    	/* LB clock ratio reg */
+#define CFG_LBC_LBCR		0x00000000    	/* LB config reg */
+#define CFG_LBC_LSRT		0x20000000  	/* LB sdram refresh timer */
+#define CFG_LBC_MRTPR		0x00000000  	/* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
+#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
+#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+/*
+ * Common settings for all Local Bus SDRAM commands.
+ * At run time, either BSMA1516 (for CPU 1.1)
+ *                  or BSMA1617 (for CPU 1.0) (old)
+ * is OR'ed in too.
+ */
+#define CFG_LBC_LSDMR_COMMON	( CFG_LBC_LSDMR_RFCR16		\
+				| CFG_LBC_LSDMR_PRETOACT7	\
+				| CFG_LBC_LSDMR_ACTTORW7	\
+				| CFG_LBC_LSDMR_BL8		\
+				| CFG_LBC_LSDMR_WRC4		\
+				| CFG_LBC_LSDMR_CL3		\
+				| CFG_LBC_LSDMR_RFEN		\
+				)
+
+/*
+ * The bcsr registers are connected to CS3 on MDS.
+ * The new memory map places bcsr at 0xf8000000.
+ *
+ * For BR3, need:
+ *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
+ *    port-size = 8-bits  = BR[19:20] = 01
+ *    no parity checking  = BR[21:22] = 00
+ *    GPMC for MSEL       = BR[24:26] = 000
+ *    Valid               = BR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
+ *
+ * For OR3, need:
+ *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
+ *    disable buffer ctrl OR[19]    = 0
+ *    CSNT                OR[20]    = 1
+ *    ACS                 OR[21:22] = 11
+ *    XACS                OR[23]    = 1
+ *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
+ *    SETA                OR[28]    = 0
+ *    TRLX                OR[29]    = 1
+ *    EHTR                OR[30]    = 1
+ *    EAD extra time      OR[31]    = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
+ */
+#define CFG_BCSR (0xf8000000)
+
+/*Chip slelect 4 - PIB*/
+#define CFG_BR4_PRELIM   0xf8008801
+#define CFG_OR4_PRELIM   0xffffe9f7
+
+/*Chip select 5 - PIB*/
+#define CFG_BR5_PRELIM	 0xf8010801
+#define CFG_OR5_PRELIM	 0xffff69f7
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
+#define CFG_INIT_RAM_END    	0x4000	    /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE  	128	    /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024)	/* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX		1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser*/
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE	8192
+
+#define OF_CPU			"PowerPC,8568@0"
+#define OF_SOC			"soc8568@e0000000"
+#define OF_TBCLK		(bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH		"/soc8568@e0000000/serial@4600"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET		0x3000
+
+/*
+ * General PCI
+ * Memory Addresses are mapped 1-1. I/O is mapped from 0
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_IO_BASE	0x00000000
+#define CFG_PCI1_IO_PHYS	0xe2000000
+#define CFG_PCI1_IO_SIZE	0x00800000	/* 8M */
+
+#define CFG_PEX_MEM_BASE	0xa0000000
+#define CFG_PEX_MEM_PHYS	CFG_PEX_MEM_BASE
+#define CFG_PEX_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PEX_IO_BASE		0x00000000
+#define CFG_PEX_IO_PHYS		0xe2800000
+#define CFG_PEX_IO_SIZE		0x00800000	/* 8M */
+
+#define CFG_SRIO_MEM_BASE	0xc0000000
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1	1
+#define CONFIG_MPC85XX_TSEC1_NAME	"eTSEC0"
+#define CONFIG_MPC85XX_TSEC2	1
+#define CONFIG_MPC85XX_TSEC2_NAME	"eTSEC1"
+#undef  CONFIG_MPC85XX_TSEC3
+#undef  CONFIG_MPC85XX_TSEC4
+#undef  CONFIG_MPC85XX_FEC
+
+#define TSEC1_PHY_ADDR		2
+#define TSEC2_PHY_ADDR		3
+
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+
+/* Options are: eTSEC[0-3] */
+#define CONFIG_ETHPRIME		"eTSEC0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+#define CFG_ENV_SIZE		0x2000
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#if defined(CONFIG_PCI)
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PCI \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#else
+#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
+				| CFG_CMD_PING \
+				| CFG_CMD_I2C \
+				| CFG_CMD_MII)
+#endif
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE	256			/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE	32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#endif
+
+#define CONFIG_IPADDR    192.168.1.253
+
+#define CONFIG_HOSTNAME  unknown
+#define CONFIG_ROOTPATH  /nfsroot
+#define CONFIG_BOOTFILE  your.uImage
+
+#define CONFIG_SERVERIP  192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK   255.255.255.0
+
+#define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10       /* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				        \
+   "netdev=eth0\0"                                                      \
+   "consoledev=ttyS0\0"                                                 \
+   "ramdiskaddr=600000\0"                                               \
+   "ramdiskfile=your.ramdisk.u-boot\0"					\
+   "fdtaddr=400000\0"							\
+   "fdtfile=your.fdt.dtb\0"						\
+   "nfsargs=setenv bootargs root=/dev/nfs rw "				\
+      "nfsroot=$serverip:$rootpath "					\
+      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+      "console=$consoledev,$baudrate $othbootargs\0"			\
+   "ramargs=setenv bootargs root=/dev/ram rw "				\
+      "console=$consoledev,$baudrate $othbootargs\0"			\
+
+
+#define CONFIG_NFSBOOTCOMMAND	                                        \
+   "run nfsargs;"							\
+   "tftp $loadaddr $bootfile;"                                          \
+   "tftp $fdtaddr $fdtfile;"						\
+   "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND \
+   "run ramargs;"							\
+   "tftp $ramdiskaddr $ramdiskfile;"                                    \
+   "tftp $loadaddr $bootfile;"                                          \
+   "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
+
+#endif	/* __CONFIG_H */