Merge http://www.denx.de/git/u-boot

12 files changed, 401 insertions, 48 deletions

diff --git a/include/ACEX1K.h b/include/ACEX1K.h
index f75c463f33..f249d6402d 100644
--- a/include/ACEX1K.h
+++ b/include/ACEX1K.h
@@ -35,6 +35,11 @@ extern int ACEX1K_dump( Altera_desc *desc, void *buf, size_t bsize );
 extern int ACEX1K_info( Altera_desc *desc );
 extern int ACEX1K_reloc( Altera_desc *desc, ulong reloc_off );
 
+extern int CYC2_load( Altera_desc *desc, void *image, size_t size );
+extern int CYC2_dump( Altera_desc *desc, void *buf, size_t bsize );
+extern int CYC2_info( Altera_desc *desc );
+extern int CYC2_reloc( Altera_desc *desc, ulong reloc_off );
+
 /* Slave Serial Implementation function table */
 typedef struct {
 	Altera_pre_fn		pre;
@@ -48,6 +53,18 @@ typedef struct {
 	int			relocated;
 } Altera_ACEX1K_Passive_Serial_fns;
 
+/* Slave Serial Implementation function table */
+typedef struct {
+	Altera_pre_fn		pre;
+	Altera_config_fn	config;
+	Altera_status_fn	status;
+	Altera_done_fn		done;
+	Altera_write_fn		write;
+	Altera_abort_fn		abort;
+	Altera_post_fn		post;
+	int			relocated;
+} Altera_CYC2_Passive_Serial_fns;
+
 /* Device Image Sizes
  *********************************************************************/
 /* ACEX1K */
@@ -60,6 +77,8 @@ typedef struct {
 #endif
 #define Altera_EP1K100_SIZE  	(166965*8)
 
+#define Altera_EP2C35_SIZE	883905
+
 /* Descriptor Macros
  *********************************************************************/
 /* ACEX1K devices */
diff --git a/include/altera.h b/include/altera.h
index 74b6729f90..7b8cb4a55d 100644
--- a/include/altera.h
+++ b/include/altera.h
@@ -34,8 +34,10 @@
 /* Altera Model definitions
  *********************************************************************/
 #define CFG_ACEX1K		CFG_FPGA_DEV( 0x1 )
+#define CFG_CYCLON2		CFG_FPGA_DEV( 0x2 )
 
 #define CFG_ALTERA_ACEX1K	(CFG_FPGA_ALTERA | CFG_ACEX1K)
+#define CFG_ALTERA_CYCLON2	(CFG_FPGA_ALTERA | CFG_CYCLON2)
 /* Add new models here */
 
 /* Altera Interface definitions
@@ -56,6 +58,7 @@ typedef enum {				/* typedef Altera_iface */
 typedef enum {			/* typedef Altera_Family */
     min_altera_type,		/* insert all new types after this */
     Altera_ACEX1K,		/* ACEX1K Family */
+    Altera_CYC2,		/* CYCLONII Family */
 /* Add new models here */
     max_altera_type		/* insert all new types before this */
 } Altera_Family;		/* end, typedef Altera_Family */
@@ -84,6 +87,7 @@ typedef int (*Altera_status_fn)( int cookie );
 typedef int (*Altera_done_fn)( int cookie );
 typedef int (*Altera_clk_fn)( int assert_clk, int flush, int cookie );
 typedef int (*Altera_data_fn)( int assert_data, int flush, int cookie );
+typedef int (*Altera_write_fn)(void *buf, size_t len, int flush, int cookie);
 typedef int (*Altera_abort_fn)( int cookie );
 typedef int (*Altera_post_fn)( int cookie );
 
diff --git a/include/common.h b/include/common.h
index 0be8372cc5..982d6a8637 100644
--- a/include/common.h
+++ b/include/common.h
@@ -270,7 +270,7 @@ int	misc_init_r   (void);
 void	jumptable_init(void);
 
 /* common/memsize.c */
-int	get_ram_size  (volatile long *, long);
+long	get_ram_size  (volatile long *, long);
 
 /* $(BOARD)/$(BOARD).c */
 void	reset_phy     (void);
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 4bae103e09..08674ca49f 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -217,43 +217,19 @@
 
 #undef	CONFIG_BOOTARGS
 
-#ifdef CONFIG_STK52XX
-# if defined(CONFIG_TQM5200_B)
-#  if defined(CFG_LOWBOOT)
-#   define ENV_UPDT							\
-	"update=protect off FC000000 FC07FFFF;"				\
-		"erase FC000000 FC07FFFF;"				\
-		"cp.b 200000 FC000000 ${filesize};"			\
-		"protect on FC000000 FC07FFFF\0"
-#  else	/* highboot */
-#   define ENV_UPDT							\
-	"update=protect off FFF00000 FFF7FFFF;"				\
-		"erase FFF00000 FFF7FFFF;"				\
+#if defined(CONFIG_TQM5200_B) && !defined(CFG_LOWBOOT)
+# define ENV_UPDT							\
+	"update=protect off FFF00000 +${filesize};"			\
+		"erase FFF00000 +${filesize};"				\
 		"cp.b 200000 FFF00000 ${filesize};"			\
-		"protect on FFF00000 FFF7FFFF\0"
-#  endif /* CFG_LOWBOOT */
-# else	/* !CONFIG_TQM5200_B */
-#  define ENV_UPDT							\
-	"update=protect off FC000000 FC05FFFF;"				\
-		"erase FC000000 FC05FFFF;"				\
-		"cp.b 200000 FC000000 ${filesize};"			\
-		"protect on FC000000 FC05FFFF\0"
-# endif /* CONFIG_TQM5200_B */
-#elif defined (CONFIG_CAM5200)
-#   define ENV_UPDT							\
-	"update=protect off FC000000 FC03FFFF;"				\
-		"erase FC000000 FC03FFFF;"				\
-		"cp.b 200000 FC000000 ${filesize};"			\
-		"protect on FC000000 FC03FFFF\0"
-#elif defined (CONFIG_FO300)
+		"protect on FFF00000 +${filesize}\0"
+#else	/* default lowboot configuration */
 #   define ENV_UPDT							\
-	"update=protect off FC000000 FC05FFFF;"				\
-		"erase FC000000 FC05FFFF;"				\
+	"update=protect off FC000000 +${filesize};"			\
+		"erase FC000000 +${filesize};"				\
 		"cp.b 200000 FC000000 ${filesize};"			\
-		"protect on FC000000 FC05FFFF\0"
-#else
-# error "Unknown Carrier Board"
-#endif	/* CONFIG_STK52XX */
+		"protect on FC000000 +${filesize}\0"
+#endif
 
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
@@ -432,7 +408,7 @@
  */
 #define CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_SIZE		0x4000	/* 16 k - keep small for fast booting */
-#if defined(CONFIG_TQM5200_B)
+#if defined(CONFIG_TQM5200_B) || defined (CONFIG_CAM5200)
 #define CFG_ENV_SECT_SIZE	0x40000
 #else
 #define CFG_ENV_SECT_SIZE	0x20000
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
new file mode 100644
index 0000000000..bbe6b76bff
--- /dev/null
+++ b/include/configs/alpr.h
@@ -0,0 +1,346 @@
+/*
+ * (C) Copyright 2006
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_ALPR		1	    /* Board is ebony		*/
+#define CONFIG_440GX		1	    /* Specifc GX support	*/
+#define CONFIG_4xx		1	    /* ... PPC4xx family	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
+#define CONFIG_LAST_STAGE_INIT	1	    /* call last_stage_init()	*/
+#undef	CFG_DRAM_TEST			    /* Disable-takes long time! */
+#define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0			*/
+#define CFG_FLASH_BASE		0xffe00000	/* start of FLASH		*/
+#define CFG_MONITOR_BASE	0xfffc0000	/* start of monitor		*/
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory		*/
+#define	CFG_PCI_MEMSIZE		0x40000000	/* size of mapped pci memory	*/
+#define CFG_PERIPHERAL_BASE	0xe0000000	/* internal peripherals		*/
+#define CFG_ISRAM_BASE		0xc0000000	/* internal SRAM		*/
+#define CFG_PCI_BASE		0xd0000000	/* internal PCI regs		*/
+#define CFG_PCI_MEMBASE1	CFG_PCI_MEMBASE  + 0x10000000
+#define CFG_PCI_MEMBASE2	CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3	CFG_PCI_MEMBASE2 + 0x10000000
+
+
+#define CFG_FPGA_BASE	    (CFG_PERIPHERAL_BASE + 0x08300000)
+#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM  1
+#define CFG_OCM_DATA_ADDR   CFG_ISRAM_BASE
+#define CFG_INIT_RAM_ADDR   CFG_ISRAM_BASE  /* Initial RAM address	*/
+#define CFG_INIT_RAM_END    0x2000	    /* End of used area in RAM	*/
+#define CFG_GBL_DATA_SIZE   128		    /* num bytes initial data	*/
+
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+
+#define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
+#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef	CFG_EXT_SERIAL_CLOCK
+#define CONFIG_BAUDRATE		115200
+#define	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
+
+#define CFG_BAUDRATE_TABLE  \
+    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI		1	/* The flash is CFI compatible		*/
+#define CFG_FLASH_CFI_DRIVER	1	/* Use common CFI driver		*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
+
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+
+#define CFG_ENV_SECT_SIZE	0x10000 	/* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SPD_EEPROM		/* Don't use SPD EEPROM for setup	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard DDR SDRAM bank 0	*/
+#undef CONFIG_SDRAM_ECC			/* enable ECC support			*/
+#define CFG_SDRAM_TABLE	{ \
+		{(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \
+		{(64 << 20),  12, 0x00082001}} /* 64MB mode 2, 12x9(4)	*/
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		100000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs	*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (PCF8594C)
+ *----------------------------------------------------------------------*/
+#define CFG_I2C_EEPROM_ADDR	0x54	/* EEPROM PCF8594C		*/
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 3	/* The Philips PCF8594C has	*/
+					/* 8 byte page write mode using */
+					/* last 3 bits of the address	*/
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	40   /* and takes up to 40 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth3\0"							\
+	"hostname=alpr\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \
+		"mem=193M\0"						\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
+	        "bootm\0"						\
+	"rootpath=/opt/projects/alpr/nfs_root\0"			\
+	"bootfile=/alpr/uImage\0"					\
+	"kernel_addr=fff00000\0"					\
+	"ramdisk_addr=fff10000\0"					\
+	"load=tftp 100000 /alpr/u-boot/u-boot.bin\0"			\
+	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
+		"cp.b 100000 fffc0000 40000;"			        \
+		"setenv filesize;saveenv\0"				\
+	"upd=run load;run update\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define CONFIG_BOOTDELAY	2	/* autoboot after 5 seconds	*/
+
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_NET_MULTI	1
+#define CONFIG_PHY_ADDR		0x02	/* dummy setting, no EMAC0 used	*/
+#define CONFIG_PHY1_ADDR	0x03	/* dummy setting, no EMAC1 used	*/
+#define CONFIG_PHY2_ADDR	0x01	/* PHY address for EMAC2	*/
+#define CONFIG_PHY3_ADDR	0x02	/* PHY address for EMAC3	*/
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
+#define CONFIG_M88E1111_PHY	1	/* needed for PHY specific setup*/
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+
+#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
+				CFG_CMD_ASKENV	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_DIAG	| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_NET	| \
+				CFG_CMD_NFS	| \
+				CFG_CMD_PCI	| \
+				CFG_CMD_PING	| \
+				CFG_CMD_FPGA	| \
+				CFG_CMD_NAND	| \
+				CFG_CMD_REGINFO)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC     	1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE	1	/* include version env variable */
+
+#define CFG_4xx_RESET_TYPE	0x2	/* use chip reset on this board	*/
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
+#define CFG_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CFG_PCI_MEMBASE */
+#define CONFIG_PCI_BOOTDELAY	1       /* enable pci bootdelay variable*/
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT		/* enable board pci_pre_init()	*/
+#define CFG_PCI_TARGET_INIT		/* let board init pci target    */
+#define CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
+#define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ *-----------------------------------------------------------------------*/
+#define CONFIG_FPGA             CFG_ALTERA_CYCLON2
+#define CFG_FPGA_CHECK_CTRLC
+#define CFG_FPGA_PROG_FEEDBACK
+#define CONFIG_FPGA_COUNT       1		/* Ich habe 2 ... aber in
+					Reihe geschaltet -> sollte gehen,
+					aufpassen mit Datasize ist jetzt
+					halt doppelt so gross ... Seite 306
+					ist das mit den multiple Device in PS
+					Mode erklaert ...*/
+
+/* FPGA program pin configuration */
+#define CFG_GPIO_CLK		18	/* FPGA clk pin (cpu output)		*/
+#define CFG_GPIO_DATA		19	/* FPGA data pin (cpu output)		*/
+#define CFG_GPIO_STATUS		20	/* FPGA status pin (cpu input)		*/
+#define CFG_GPIO_CONFIG		21	/* FPGA CONFIG pin (cpu output)		*/
+#define CFG_GPIO_CON_DON	22	/* FPGA CONFIG_DONE pin (cpu input)	*/
+
+#define CFG_GPIO_SEL_DPR	14	/* cpu output */
+#define CFG_GPIO_SEL_AVR	15	/* cpu output */
+#define CFG_GPIO_PROG_EN	23	/* cpu output */
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup
+ *-----------------------------------------------------------------------*/
+#define CFG_GPIO_EREADY		(0x80000000 >> 26)
+#define CFG_GPIO_REV0		(0x80000000 >> 14)
+#define CFG_GPIO_REV1		(0x80000000 >> 15)
+
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE	4
+#define NAND_MAX_CHIPS		CFG_MAX_NAND_DEVICE
+#define CFG_NAND_BASE		0xF0000000	/* NAND FLASH Base Address	*/
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE + 0, CFG_NAND_BASE + 2,	\
+				  CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 }
+#define CFG_NAND_QUIET_TEST	1	/* don't warn upon unknown NAND flash	*/
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH		CFG_FLASH_BASE
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		(CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (NAND-FLASH) initialization					*/
+#define CFG_EBC_PB1AP		0x01840380	/* TWT=3			*/
+#define CFG_EBC_PB1CR		(CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		32768	/* For AMCC 440 CPUs			*/
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+#endif	/* __CONFIG_H */
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 3a76315b44..00b92220c1 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -53,7 +53,7 @@
 
 #define CFG_BOOT_BASE_ADDR	0xf0000000
 #define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
-#define CFG_FLASH_BASE		0xfe000000	/* start of FLASH	*/
+#define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
 #define CFG_MONITOR_BASE	TEXT_BASE
 #define CFG_NAND_ADDR		0xd0000000      /* NAND Flash		*/
 #define CFG_OCM_BASE		0xe0010000      /* ocm			*/
@@ -102,6 +102,7 @@
 #define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
 #else
 #define CFG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
+#define CFG_ENV_IS_EMBEDDED	1	/* use embedded environment */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -234,10 +235,10 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
+	"rootpath=/opt/eldk/ppc_4xxFP\0"					\
 	"bootfile=/tftpboot/sequoia/uImage\0"				\
-	"kernel_addr=FE000000\0"					\
-	"ramdisk_addr=FE180000\0"					\
+	"kernel_addr=FC000000\0"					\
+	"ramdisk_addr=FC180000\0"					\
 	"load=tftp 100000 /tftpboot/sequoia/u-boot.bin\0"		\
 	"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;"	\
 		"cp.b 100000 FFFA0000 60000\0"			        \
@@ -378,7 +379,7 @@
 #define CFG_NAND_CS		3		/* NAND chip connected to CSx	*/
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
 #define CFG_EBC_PB0AP		0x03017300
-#define CFG_EBC_PB0CR		(CFG_FLASH | 0xba000)
+#define CFG_EBC_PB0CR		(CFG_FLASH | 0xda000)
 
 /* Memory Bank 3 (NAND-FLASH) initialization					*/
 #define CFG_EBC_PB3AP		0x018003c0
@@ -387,7 +388,7 @@
 #define CFG_NAND_CS		0		/* NAND chip connected to CSx	*/
 /* Memory Bank 3 (NOR-FLASH) initialization					*/
 #define CFG_EBC_PB3AP		0x03017300
-#define CFG_EBC_PB3CR		(CFG_FLASH | 0xba000)
+#define CFG_EBC_PB3CR		(CFG_FLASH | 0xda000)
 
 /* Memory Bank 0 (NAND-FLASH) initialization					*/
 #define CFG_EBC_PB0AP		0x018003c0
diff --git a/include/configs/v38b.h b/include/configs/v38b.h
index cf2d031c9f..554a7a41b8 100644
--- a/include/configs/v38b.h
+++ b/include/configs/v38b.h
@@ -34,7 +34,7 @@
 #define CONFIG_RTC_PCF8563		1	/* has PCF8563 RTC */
 #define CONFIG_MPC5200_DDR		1	/* has DDR SDRAM */
 
-#define CONFIG_HW_WATCHDOG		1	/* has watchdog */
+#undef CONFIG_HW_WATCHDOG			/* don't use watchdog */
 
 #define CONFIG_NETCONSOLE		1
 
@@ -246,7 +246,7 @@
 /*
  * GPIO configuration
  */
-#define CFG_GPS_PORT_CONFIG	0x90000404
+#define CFG_GPS_PORT_CONFIG	0x90001404
 
 /*
  * Miscellaneous configurable options
diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h
index ba27f37f6e..58717f8a60 100644
--- a/include/configs/yellowstone.h
+++ b/include/configs/yellowstone.h
@@ -37,6 +37,7 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
+#define CONFIG_BOARD_RESET	1	/* call board_reset()		*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index 3d7b4a2f4b..6e942abcaa 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -37,6 +37,7 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
+#define CONFIG_BOARD_RESET	1	/* call board_reset()		*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
diff --git a/include/environment.h b/include/environment.h
index 26b07120da..af605ab7a9 100644
--- a/include/environment.h
+++ b/include/environment.h
@@ -79,8 +79,7 @@
 # ifdef CFG_ENV_OFFSET_REDUND
 #  define CFG_REDUNDAND_ENVIRONMENT
 # endif
-# if defined(CONFIG_NAND_U_BOOT)
-/* Use embedded environment in NAND boot versions */
+# ifdef CFG_ENV_IS_EMBEDDED
 #  define ENV_IS_EMBEDDED	1
 # endif
 #endif /* CFG_ENV_IS_IN_NAND */
diff --git a/include/flash.h b/include/flash.h
index d91589a6c0..9c57cbc427 100644
--- a/include/flash.h
+++ b/include/flash.h
@@ -43,9 +43,14 @@ typedef struct {
 	ulong	write_tout;		/* maximum write timeout		*/
 	ulong	buffer_write_tout;	/* maximum buffer write timeout		*/
 	ushort	vendor;			/* the primary vendor id		*/
-	ushort	cmd_reset;		/* Vendor specific reset command	*/
+	ushort	cmd_reset;		/* vendor specific reset command	*/
 	ushort	interface;		/* used for x8/x16 adjustments		*/
 	ushort	legacy_unlock;		/* support Intel legacy (un)locking	*/
+	uchar	manufacturer_id;	/* manufacturer id			*/
+	ushort	device_id;		/* device id				*/
+	ushort	device_id2;		/* extended device id			*/
+	ushort	ext_addr;		/* extended query table address		*/
+	ushort	cfi_version;		/* cfi version				*/
 #endif
 } flash_info_t;
 
@@ -439,6 +444,7 @@ extern void flash_read_factory_serial(flash_info_t * info, void * buffer, int of
 #define FLASH_MAN_MT	0x00400000
 #define FLASH_MAN_SHARP 0x00500000
 #define FLASH_MAN_ATM	0x00600000
+#define FLASH_MAN_CFI	0x01000000
 
 
 #define FLASH_TYPEMASK	0x0000FFFF	/* extract FLASH type	information	*/
diff --git a/include/ppc440.h b/include/ppc440.h
index e407320a9e..407daaebe8 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -3183,7 +3183,7 @@
 #define GPIO0			0
 #define GPIO1			1
 
-#if defined(CONFIG_440GP)
+#if defined(CONFIG_440GP) || defined(CONFIG_440GX)
 #define GPIO0_BASE             (CFG_PERIPHERAL_BASE+0x00000700)
 
 #define GPIO0_OR               (GPIO0_BASE+0x0)