Add MMC Framework

Here's a new framework (based roughly off the linux one) for managing
MMC controllers.  It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.

This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)

Some of this code was contributed by Dave Liu <daveliu@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>

1 files changed, 181 insertions, 9 deletions

diff --git a/include/mmc.h b/include/mmc.h
index e41033f291..b9b27ba181 100644
--- a/include/mmc.h
+++ b/include/mmc.h
@@ -1,6 +1,8 @@
 /*
- * (C) Copyright 2000-2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Copyright 2008, Freescale Semiconductor, Inc
+ * Andy Fleming
+ *
+ * Based (loosely) on the Linux code
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -24,36 +26,149 @@
 #ifndef _MMC_H_
 #define _MMC_H_
 
-/* MMC command numbers */
+#include <linux/list.h>
+
+#define SD_VERSION_SD	0x20000
+#define SD_VERSION_2	(SD_VERSION_SD | 0x20)
+#define SD_VERSION_1_0	(SD_VERSION_SD | 0x10)
+#define SD_VERSION_1_10	(SD_VERSION_SD | 0x1a)
+#define MMC_VERSION_MMC		0x10000
+#define MMC_VERSION_UNKNOWN	(MMC_VERSION_MMC)
+#define MMC_VERSION_1_2		(MMC_VERSION_MMC | 0x12)
+#define MMC_VERSION_1_4		(MMC_VERSION_MMC | 0x14)
+#define MMC_VERSION_2_2		(MMC_VERSION_MMC | 0x22)
+#define MMC_VERSION_3		(MMC_VERSION_MMC | 0x30)
+#define MMC_VERSION_4		(MMC_VERSION_MMC | 0x40)
+
+#define MMC_MODE_HS		0x001
+#define MMC_MODE_HS_52MHz	0x010
+#define MMC_MODE_4BIT		0x100
+#define MMC_MODE_8BIT		0x200
+
+#define SD_DATA_4BIT	0x00040000
+
+#define IS_SD(x) (mmc->version & SD_VERSION_SD)
+
+#define MMC_DATA_READ		1
+#define MMC_DATA_WRITE		2
+
+#define NO_CARD_ERR		-16 /* No SD/MMC card inserted */
+#define UNUSABLE_ERR		-17 /* Unusable Card */
+#define COMM_ERR		-18 /* Communications Error */
+#define TIMEOUT			-19
+
 #define MMC_CMD_GO_IDLE_STATE		0
 #define MMC_CMD_SEND_OP_COND		1
 #define MMC_CMD_ALL_SEND_CID		2
 #define MMC_CMD_SET_RELATIVE_ADDR	3
 #define MMC_CMD_SET_DSR			4
+#define MMC_CMD_SWITCH			6
 #define MMC_CMD_SELECT_CARD		7
+#define MMC_CMD_SEND_EXT_CSD		8
 #define MMC_CMD_SEND_CSD		9
 #define MMC_CMD_SEND_CID		10
+#define MMC_CMD_STOP_TRANSMISSION	12
 #define MMC_CMD_SEND_STATUS		13
 #define MMC_CMD_SET_BLOCKLEN		16
 #define MMC_CMD_READ_SINGLE_BLOCK	17
 #define MMC_CMD_READ_MULTIPLE_BLOCK	18
-#define MMC_CMD_WRITE_BLOCK		24
+#define MMC_CMD_WRITE_SINGLE_BLOCK	24
+#define MMC_CMD_WRITE_MULTIPLE_BLOCK	25
 #define MMC_CMD_APP_CMD			55
 
-/* SD Card command numbers */
 #define SD_CMD_SEND_RELATIVE_ADDR	3
-#define SD_CMD_SWITCH			6
+#define SD_CMD_SWITCH_FUNC		6
 #define SD_CMD_SEND_IF_COND		8
 
 #define SD_CMD_APP_SET_BUS_WIDTH	6
 #define SD_CMD_APP_SEND_OP_COND		41
+#define SD_CMD_APP_SEND_SCR		51
+
+/* SCR definitions in different words */
+#define SD_HIGHSPEED_BUSY	0x00020000
+#define SD_HIGHSPEED_SUPPORTED	0x00020000
+
+#define MMC_HS_TIMING		0x00000100
+#define MMC_HS_52MHZ		0x2
+
+#define OCR_BUSY	0x80
+#define OCR_HCS		0x40000000
+
+#define MMC_VDD_165_195		0x00000080	/* VDD voltage 1.65 - 1.95 */
+#define MMC_VDD_20_21		0x00000100	/* VDD voltage 2.0 ~ 2.1 */
+#define MMC_VDD_21_22		0x00000200	/* VDD voltage 2.1 ~ 2.2 */
+#define MMC_VDD_22_23		0x00000400	/* VDD voltage 2.2 ~ 2.3 */
+#define MMC_VDD_23_24		0x00000800	/* VDD voltage 2.3 ~ 2.4 */
+#define MMC_VDD_24_25		0x00001000	/* VDD voltage 2.4 ~ 2.5 */
+#define MMC_VDD_25_26		0x00002000	/* VDD voltage 2.5 ~ 2.6 */
+#define MMC_VDD_26_27		0x00004000	/* VDD voltage 2.6 ~ 2.7 */
+#define MMC_VDD_27_28		0x00008000	/* VDD voltage 2.7 ~ 2.8 */
+#define MMC_VDD_28_29		0x00010000	/* VDD voltage 2.8 ~ 2.9 */
+#define MMC_VDD_29_30		0x00020000	/* VDD voltage 2.9 ~ 3.0 */
+#define MMC_VDD_30_31		0x00040000	/* VDD voltage 3.0 ~ 3.1 */
+#define MMC_VDD_31_32		0x00080000	/* VDD voltage 3.1 ~ 3.2 */
+#define MMC_VDD_32_33		0x00100000	/* VDD voltage 3.2 ~ 3.3 */
+#define MMC_VDD_33_34		0x00200000	/* VDD voltage 3.3 ~ 3.4 */
+#define MMC_VDD_34_35		0x00400000	/* VDD voltage 3.4 ~ 3.5 */
+#define MMC_VDD_35_36		0x00800000	/* VDD voltage 3.5 ~ 3.6 */
+
+#define MMC_SWITCH_MODE_CMD_SET		0x00 /* Change the command set */
+#define MMC_SWITCH_MODE_SET_BITS	0x01 /* Set bits in EXT_CSD byte
+						addressed by index which are
+						1 in value field */
+#define MMC_SWITCH_MODE_CLEAR_BITS	0x02 /* Clear bits in EXT_CSD byte
+						addressed by index, which are
+						1 in value field */
+#define MMC_SWITCH_MODE_WRITE_BYTE	0x03 /* Set target byte to value */
+
+#define SD_SWITCH_CHECK		0
+#define SD_SWITCH_SWITCH	1
+
+/*
+ * EXT_CSD fields
+ */
+
+#define EXT_CSD_BUS_WIDTH	183	/* R/W */
+#define EXT_CSD_HS_TIMING	185	/* R/W */
+#define EXT_CSD_CARD_TYPE	196	/* RO */
+#define EXT_CSD_REV		192	/* RO */
+#define EXT_CSD_SEC_CNT		212	/* RO, 4 bytes */
+
+/*
+ * EXT_CSD field definitions
+ */
+
+#define EXT_CSD_CMD_SET_NORMAL		(1<<0)
+#define EXT_CSD_CMD_SET_SECURE		(1<<1)
+#define EXT_CSD_CMD_SET_CPSECURE	(1<<2)
+
+#define EXT_CSD_CARD_TYPE_26	(1<<0)	/* Card can run at 26MHz */
+#define EXT_CSD_CARD_TYPE_52	(1<<1)	/* Card can run at 52MHz */
+
+#define EXT_CSD_BUS_WIDTH_1	0	/* Card is in 1 bit mode */
+#define EXT_CSD_BUS_WIDTH_4	1	/* Card is in 4 bit mode */
+#define EXT_CSD_BUS_WIDTH_8	2	/* Card is in 8 bit mode */
 
 #define R1_ILLEGAL_COMMAND		(1 << 22)
 #define R1_APP_CMD			(1 << 5)
 
-int mmc_legacy_init(int verbose);
-int mmc_read(ulong src, uchar *dst, int size);
-int mmc_write(uchar *src, ulong dst, int size);
+#define MMC_RSP_PRESENT (1 << 0)
+#define MMC_RSP_136     (1 << 1)                /* 136 bit response */
+#define MMC_RSP_CRC     (1 << 2)                /* expect valid crc */
+#define MMC_RSP_BUSY    (1 << 3)                /* card may send busy */
+#define MMC_RSP_OPCODE  (1 << 4)                /* response contains opcode */
+
+#define MMC_RSP_NONE    (0)
+#define MMC_RSP_R1      (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+#define MMC_RSP_R1b	(MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE| \
+			MMC_RSP_BUSY)
+#define MMC_RSP_R2      (MMC_RSP_PRESENT|MMC_RSP_136|MMC_RSP_CRC)
+#define MMC_RSP_R3      (MMC_RSP_PRESENT)
+#define MMC_RSP_R4      (MMC_RSP_PRESENT)
+#define MMC_RSP_R5      (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+#define MMC_RSP_R6      (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+#define MMC_RSP_R7      (MMC_RSP_PRESENT|MMC_RSP_CRC|MMC_RSP_OPCODE)
+
 
 struct mmc_cid {
 	unsigned long psn;
@@ -104,4 +219,61 @@ struct mmc_csd
 	u8	one:1;
 };
 
+struct mmc_cmd {
+	ushort cmdidx;
+	uint resp_type;
+	uint cmdarg;
+	char response[18];
+	uint flags;
+};
+
+struct mmc_data {
+	union {
+		char *dest;
+		const char *src; /* src buffers don't get written to */
+	};
+	uint flags;
+	uint blocks;
+	uint blocksize;
+};
+
+struct mmc {
+	struct list_head link;
+	char name[32];
+	void *priv;
+	uint voltages;
+	uint version;
+	uint f_min;
+	uint f_max;
+	int high_capacity;
+	uint bus_width;
+	uint clock;
+	uint card_caps;
+	uint host_caps;
+	uint ocr;
+	uint scr[2];
+	uint csd[4];
+	char cid[16];
+	ushort rca;
+	uint tran_speed;
+	uint read_bl_len;
+	uint write_bl_len;
+	u64 capacity;
+	block_dev_desc_t block_dev;
+	int (*send_cmd)(struct mmc *mmc,
+			struct mmc_cmd *cmd, struct mmc_data *data);
+	void (*set_ios)(struct mmc *mmc);
+	int (*init)(struct mmc *mmc);
+};
+
+int mmc_register(struct mmc *mmc);
+int mmc_initialize(bd_t *bis);
+int mmc_init(struct mmc *mmc);
+int mmc_read(struct mmc *mmc, u64 src, uchar *dst, int size);
+struct mmc *find_mmc_device(int dev_num);
+void print_mmc_devices(char separator);
+
+#ifndef CONFIG_GENERIC_MMC
+int mmc_legacy_init(int verbose);
+#endif
 #endif /* _MMC_H_ */