Blackfin: unify common ADI board settings

Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that.  This
will also make merging the ~10 boards I have to forward port a lot easier.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

1 files changed, 156 insertions, 285 deletions

diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
index f6399a9f52..7c35a022f9 100644
--- a/include/configs/bf537-stamp.h
+++ b/include/configs/bf537-stamp.h
@@ -2,272 +2,144 @@
  * U-boot - Configuration file for BF537 STAMP board
  */
 
-#ifndef __CONFIG_BF537_H__
-#define __CONFIG_BF537_H__
+#ifndef __CONFIG_BF537_STAMP_H__
+#define __CONFIG_BF537_STAMP_H__
 
 #include <asm/blackfin-config-pre.h>
 
-#define CONFIG_SYS_LONGHELP		1
-#define CONFIG_CMDLINE_EDITING	1
-#define CONFIG_BAUDRATE		57600
-/* Set default serial console for bf537 */
-#define CONFIG_UART_CONSOLE	0
-#define CONFIG_BOOTDELAY	5
-/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/
-/*#define CONFIG_BF537_STAMP_LEDCMD	1*/
-
-#define CONFIG_PANIC_HANG 1
 
-#define CONFIG_BFIN_CPU	bf537-0.2
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-#define CONFIG_BFIN_MAC
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU             bf537-0.2
+#define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_BYPASS
 
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
 
-/* Define if want to do post memory test */
-#undef CONFIG_POST_TEST
-
-#define CONFIG_RTC_BFIN		1
-#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
-
-/* CONFIG_CLKIN_HZ is any value in Hz				*/
-#define CONFIG_CLKIN_HZ		25000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
-/*						    1=CLKIN/2	*/
-#define CONFIG_CLKIN_HALF	0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/*						    1=bypass PLL*/
-#define CONFIG_PLL_BYPASS	0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	*/
-/* Values can range from 1-64					*/
+/*
+ * Clock Settings
+ *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ *	SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz					*/
+#define CONFIG_CLKIN_HZ			25000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN		*/
+/*                                                1 = CLKIN / 2		*/
+#define CONFIG_CLKIN_HALF		0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass	*/
+/*                                                1 = bypass PLL	*/
+#define CONFIG_PLL_BYPASS		0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL		*/
+/* Values can range from 0-63 (where 0 means 64)			*/
 #define CONFIG_VCO_MULT			20
-/* CONFIG_CCLK_DIV controls what the core clock divider is	*/
-/* Values can be 1, 2, 4, or 8 ONLY				*/
+/* CCLK_DIV controls the core clock divider				*/
+/* Values can be 1, 2, 4, or 8 ONLY					*/
 #define CONFIG_CCLK_DIV			1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
-/* Values can range from 1-15					*/
+/* SCLK_DIV controls the system clock divider				*/
+/* Values can range from 1-15						*/
 #define CONFIG_SCLK_DIV			5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
-/* Values can range from 2-65535				*/
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
-#define CONFIG_SPI_BAUD			2
-#define CONFIG_SPI_BAUD_INITBLOCK	4
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#define CONFIG_MEM_SIZE			64	/* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH		10	/* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC32M8A2_75	1
 
-#define CONFIG_LOADS_ECHO		1
 
 /*
- * rarpb, bootp or dhcp commands will perform only a
- * configuration lookup from the BOOTP/DHCP server
- * but not try to load any image using TFTP
+ * Memory Settings
  */
-#define CONFIG_SYS_AUTOLOAD			"no"
+#define CONFIG_MEM_ADD_WDTH	10
+#define CONFIG_MEM_SIZE		64
+
+#define CONFIG_EBIU_SDRRC_VAL	0x306
+#define CONFIG_EBIU_SDGCTL_VAL	0x91114d
+
+#define CONFIG_EBIU_AMGCTL_VAL	0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL	0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL	0xFFC27BB0
+
+#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(384 * 1024)
+
 
 /*
  * Network Settings
  */
-/* network support */
-#ifdef CONFIG_BFIN_MAC
-#define CONFIG_IPADDR		192.168.0.15
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_GATEWAYIP	192.168.0.1
-#define CONFIG_SERVERIP		192.168.0.2
-#define CONFIG_HOSTNAME		BF537
+#ifndef __ADSPBF534__
+#define ADI_CMDS_NETWORK	1
+#define CONFIG_BFIN_MAC
+#define CONFIG_NETCONSOLE	1
+#define CONFIG_NET_MULTI	1
 #endif
-
-#define CONFIG_ROOTPATH		/romfs
+#define CONFIG_HOSTNAME		bf537-stamp
 /* Uncomment next line to use fixed MAC address */
 /* #define CONFIG_ETHADDR	02:80:ad:20:31:e8 */
-/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */
-
-#define CONFIG_SYS_LONGHELP		1
-#define CONFIG_BOOTDELAY	5
-#define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND	"run ramboot"
-
-#if defined(CONFIG_POST_TEST)
-/* POST support */
-#define CONFIG_POST		( CONFIG_SYS_POST_MEMORY | \
-				  CONFIG_SYS_POST_UART	  | \
-				  CONFIG_SYS_POST_FLASH  | \
-				  CONFIG_SYS_POST_ETHER  | \
-				  CONFIG_SYS_POST_LED	  | \
-				  CONFIG_SYS_POST_BUTTON)
-#else
-#undef CONFIG_POST
-#endif
 
-#ifdef CONFIG_POST
-#define FLASH_START_POST_BLOCK	11	/* Should > = 11 */
-#define FLASH_END_POST_BLOCK	71	/* Should < = 71 */
-#endif
-
-/* CF-CARD IDE-HDD Support */
-
-/* #define CONFIG_BFIN_TRUE_IDE */	/* Add CF flash card support */
-/* #define CONFIG_BFIN_CF_IDE */	/* Add CF flash card support */
-/* #define CONFIG_BFIN_HDD_IDE */	/* Add IDE Disk Drive (HDD) support */
-
-#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE)
-# define CONFIG_BFIN_IDE	1
-#endif
-
-/*#define CONFIG_BF537_NAND */		/* Add nand flash support */
-
-#define CONFIG_NETCONSOLE	1
-#define CONFIG_NET_MULTI	1
 
 /*
- * BOOTP options
+ * Flash Settings
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE		0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
+#define CONFIG_SYS_MAX_FLASH_SECT	71
 
 
 /*
- * Command line configuration.
+ * SPI Settings
  */
-#include <config_cmd_default.h>
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ	30000000
+#define CONFIG_SF_DEFAULT_HZ	30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_WINBOND
 
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
 
-#ifndef CONFIG_BFIN_MAC
-#undef CONFIG_CMD_NET
+/*
+ * Env Storage Settings
+ */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET	0x4000
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x2000
 #else
-#define CONFIG_CMD_PING
-#endif
-
-#if defined(CONFIG_BFIN_CF_IDE) \
-	|| defined(CONFIG_BFIN_HDD_IDE) \
-	|| defined(CONFIG_BFIN_TRUE_IDE)
-#define CONFIG_CMD_IDE
-#endif
-
-#define CONFIG_CMD_DHCP
-
-#if defined(CONFIG_POST)
-#define CONFIG_CMD_DIAG
-#endif
-
-#ifdef CONFIG_BF537_NAND
-#define CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET	0x4000
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x2000
 #endif
-
-
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
-#define CONFIG_LOADADDR	0x1000000
-
-#define CONFIG_EXTRA_ENV_SETTINGS				\
-	"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0"	\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "		\
-	"nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
-	"addip=setenv bootargs $(bootargs) "			\
-	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
-	":$(hostname):eth0:off\0"				\
-	"ramboot=tftpboot $(loadaddr) linux;"			\
-	"run ramargs;run addip;bootelf\0"			\
-	"nfsboot=tftpboot $(loadaddr) linux;"			\
-	"run nfsargs;run addip;bootelf\0"			\
-	"flashboot=bootm 0x20100000\0"				\
-	"update=tftpboot $(loadaddr) u-boot.bin;"		\
-	"protect off 0x20000000 0x2007FFFF;"			\
-	"erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0"	\
-	""
-
-#define	CONFIG_SYS_PROMPT		"bfin> "	/* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
 #else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define ENV_IS_EMBEDDED_CUSTOM
 #endif
-#define CONFIG_SYS_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024*1024)
-#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_SYS_MEMTEST_START	0x0	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		( (CONFIG_MEM_SIZE - 1) * 1024*1024)	/* 1 ... 63 MB in DRAM */
-#define	CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR	/* default load address */
-#define	CONFIG_SYS_HZ			1000	/* decrementer freq: 10 ms ticks */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-
-#define CONFIG_SYS_FLASH_BASE		0x20000000
-#define CONFIG_SYS_FLASH_CFI		/* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER	/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_SYS_MAX_FLASH_BANKS	1
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
 
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_SIZE	0x4000
-#define CONFIG_SYS_GBL_DATA_ADDR	(CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE	(CONFIG_SYS_GBL_DATA_ADDR  - 4)
 
-#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
-#define CONFIG_ENV_IS_IN_EEPROM	1
-#define CONFIG_ENV_OFFSET		0x4000
-#define CONFIG_ENV_HEADER		(CONFIG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */
-#else
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		0x20004000
-#define CONFIG_ENV_OFFSET		(CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
-#endif
-#define CONFIG_ENV_SIZE		0x2000
-#define	CONFIG_ENV_SECT_SIZE	0x2000	/* Total Size of Environment Sector */
-#define ENV_IS_EMBEDDED
-
-/* JFFS Partition offset set  */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	0
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR	15
+/*
+ * I2C Settings
+ */
+#define CONFIG_BFIN_TWI_I2C	1
+#define CONFIG_HARD_I2C		1
+#define CONFIG_SYS_I2C_SPEED	50000
+#define CONFIG_SYS_I2C_SLAVE	0
 
-#define CONFIG_SPI
 
 /*
- * Stack sizes
+ * SPI_MMC Settings
  */
-#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+#define CONFIG_MMC
+#define CONFIG_BFIN_SPI_MMC
 
-#define POLL_MODE		1
-#define FLASH_TOT_SECT		71
-#define FLASH_SIZE		0x400000
-#define CONFIG_SYS_FLASH_SIZE		0x400000
 
 /*
- * Board NAND Infomation
+ * NAND Settings
  */
+/* #define CONFIG_BF537_NAND */
+#ifdef CONFIG_BF537_NAND
+# define CONFIG_CMD_NAND
+#endif
 
 #define CONFIG_SYS_NAND_ADDR		0x20212000
 #define CONFIG_SYS_NAND_BASE		CONFIG_SYS_NAND_ADDR
@@ -280,56 +152,35 @@
 #define NAND_MAX_FLOORS		1
 #define BFIN_NAND_READY		PF3
 
-#define NAND_WAIT_READY(nand)			\
-	do {					\
-		int timeout = 0;		\
-		while(!(*pPORTFIO & PF3))	\
-			if (timeout++ > 100000)	\
-				break;		\
+#define NAND_WAIT_READY(nand) \
+	do { \
+		int timeout = 0; \
+		while (!(*pPORTFIO & PF3)) \
+			if (timeout++ > 100000) \
+				break; \
 	} while (0)
 
-#define BFIN_NAND_CLE		(1<<2)	/* A2 -> Command Enable */
-#define BFIN_NAND_ALE		(1<<1)	/* A1 -> Address Enable */
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-/*
- * Initialize PSD4256 registers for using I2C
- */
-#define CONFIG_MISC_INIT_R
+#define BFIN_NAND_CLE		(1 << 2)	/* A2 -> Command Enable */
+#define BFIN_NAND_ALE		(1 << 1)	/* A1 -> Address Enable */
+#define WRITE_NAND_COMMAND(d, adr) bfin_write8(adr | BFIN_NAND_CLE, d)
+#define WRITE_NAND_ADDRESS(d, adr) bfin_write8(adr | BFIN_NAND_ALE, d)
+#define WRITE_NAND(d, adr)         bfin_write8(adr, d)
+#define READ_NAND(adr)             bfin_read8(adr)
 
-#define CONFIG_SYS_BOOTM_LEN		0x4000000	/* Large Image Length, set to 64 Meg */
 
 /*
- * I2C settings
+ * CF-CARD IDE-HDD Support
  */
-#define CONFIG_HARD_I2C		1
-#define CONFIG_BFIN_TWI_I2C	1
-#define CONFIG_SYS_I2C_SPEED	50000
-#define CONFIG_SYS_I2C_SLAVE	0
-
-#define CONFIG_EBIU_SDRRC_VAL  0x306
-#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
-#define CONFIG_EBIU_SDBCTL_VAL 0x25
-
-#define CONFIG_EBIU_AMGCTL_VAL		0xFF
-#define CONFIG_EBIU_AMBCTL0_VAL		0x7BB07BB0
-#define CONFIG_EBIU_AMBCTL1_VAL		0xFFC27BB0
-
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL		(B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
-				~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL		(B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
-				B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
+/* #define CONFIG_BFIN_TRUE_IDE */	/* Add CF flash card support */
+/* #define CONFIG_BFIN_CF_IDE */	/* Add CF flash card support */
+/* #define CONFIG_BFIN_HDD_IDE */	/* Add IDE Disk Drive (HDD) support */
 
-#define AMGCTLVAL		0xFF
-#define AMBCTL0VAL		0x7BB07BB0
-#define AMBCTL1VAL		0xFFC27BB0
+#if defined(CONFIG_BFIN_CF_IDE) || \
+    defined(CONFIG_BFIN_HDD_IDE) || \
+    defined(CONFIG_BFIN_TRUE_IDE)
+# define CONFIG_BFIN_IDE	1
+# define CONFIG_CMD_IDE
+#endif
 
 #if defined(CONFIG_BFIN_IDE)
 
@@ -341,11 +192,11 @@
 #undef  CONFIG_IDE_LED		/* no led for ide supported */
 #undef  CONFIG_IDE_RESET	/* no reset for ide supported */
 
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*1)	/* max. 1 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS * 1)
 
-#undef  AMBCTL1VAL
-#define AMBCTL1VAL		0xFFC3FFC3
+#undef  CONFIG_EBIU_AMBCTL1_VAL
+#define CONFIG_EBIU_AMBCTL1_VAL		0xFFC3FFC3
 
 #define CONFIG_CF_ATASEL_DIS	0x20311800
 #define CONFIG_CF_ATASEL_ENA	0x20311802
@@ -357,34 +208,54 @@
  */
 #define CONFIG_SYS_ATA_BASE_ADDR	0x2031C000
 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0020	/* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET	0x0020	/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x001C	/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET	0x0020	/* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET	0x0020	/* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x001C	/* alternate registers */
 #define CONFIG_SYS_ATA_STRIDE		2	/* CF.A0 --> Blackfin.Ax */
-#endif				/* CONFIG_BFIN_TRUE_IDE */
 
-#if defined(CONFIG_BFIN_CF_IDE)	/* USE CompactFlash Storage Card in the common memory space */
+#elif defined(CONFIG_BFIN_CF_IDE)
 #define CONFIG_SYS_ATA_BASE_ADDR	0x20211800
 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x000E	/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000	/* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET	0x0000	/* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x000E	/* alternate registers */
 #define CONFIG_SYS_ATA_STRIDE		1	/* CF.A0 --> Blackfin.Ax */
-#endif				/* CONFIG_BFIN_CF_IDE */
 
-#if defined(CONFIG_BFIN_HDD_IDE)	/* USE TRUE IDE */
+#elif defined(CONFIG_BFIN_HDD_IDE)
 #define CONFIG_SYS_ATA_BASE_ADDR	0x20314000
 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0020	/* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET	0x0020	/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x001C	/* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET	0x0020	/* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET	0x0020	/* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x001C	/* alternate registers */
 #define CONFIG_SYS_ATA_STRIDE		2	/* CF.A0 --> Blackfin.A1 */
-
 #undef  CONFIG_SCLK_DIV
 #define CONFIG_SCLK_DIV		8
-#endif				/* CONFIG_BFIN_HDD_IDE */
+#endif
+
+#endif
 
-#endif				/*CONFIG_BFIN_IDE */
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE	0
+
+/* #define CONFIG_BF537_STAMP_LEDCMD	1 */
+
+/* Define if want to do post memory test */
+#undef CONFIG_POST
+#ifdef CONFIG_POST
+#define FLASH_START_POST_BLOCK	11	/* Should > = 11 */
+#define FLASH_END_POST_BLOCK	71	/* Should < = 71 */
+#endif
+
+
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
 
 #include <asm/blackfin-config-post.h>