Patch by Scott McNutt, 25 Apr 2004:

Add Nios GDB/JTAG Console support:
- Add stubs to support gdb via JTAG.
- Add support for console over JTAG.
- Minor cleanup.

1 files changed, 109 insertions, 9 deletions

diff --git a/doc/README.nios b/doc/README.nios
index d3a9277b2a..671e7277fa 100644
--- a/doc/README.nios
+++ b/doc/README.nios
@@ -55,6 +55,12 @@ sources (when altera silicon is not involved). This isn't really
 a problem as little, if any, of the Altera source contains
 features that are not already available in U-Boot.
 
+1.3 Debugging via OCI
+---------------------
+The Nios port supports debugging with gdb and/or nios-console
+via the JTAG port. Stubs for debugging with gdb via the serial
+port are not currently implemented.
+
 
 2. CONFIGURATION OPTIONS/SETTINGS
 ----------------------------------
@@ -79,7 +85,11 @@ description).
 
 CONFIG_NIOS -- defined for all Nios-32 boards.
 
-CFG_NIOS_CONSOLE -- the base address of the console UART.
+CFG_NIOS_CONSOLE -- the base address of the console UART or the JTAG
+	stdio port. To enable a console via JTAG, define
+	CONFIG_CONSOLE_JTAG and set CGF_NIOS_CONSOLE to the base address
+	of the JTAG stdio port (normally OCI base + 0x00fa). Then
+	run nios-console with the -w option.
 	(standard-32: nasys_uart_0 resp. na_uart1_base).
 
 CFG_NIOS_FIXEDBAUD -- defined if the console UART PTF fixed_baud
@@ -176,20 +186,109 @@ GERMS monitor (that is, avoid running code stored in flash memory):
     3. Release CFG_NIOS_CPU_BUTTON_PIO, button number 0.
 
 
-5. BRAIN DAMAGE
+5. DEBUGGING WITH GDB
+---------------------
+
+Debug sessions using gdb are currently supported only via JTAG. The
+stubs for debugging via a serial port are not implemented. To enable
+the gdb JTAG stubs, simply reference _brkpt_hw_int and _brkpt_sw_int
+at vector table offsets 3 and 4, respectively. For an example, see
+board/altera/dk1c20/vectors.S.
+
+5.1 Vector Table Initialization and ROM Stubs
+---------------------------------------------
+If CONFIG_ROM_STUBS is defined, the debug breakpoint and single step
+entries in the vector table are restored to their initial values
+immediately _after_ initializing the vector table. Defining this macro
+is useful when ROM-based stubs are implemented.
+
+NOTE: The default GERMS monitor does NOT implement gdb stubs, nor does
+it initialize the vector table. Therefore, when debugging U-Boot, you
+should NOT set a software breakpoint prior to vector table initialization.
+
+5.2 Starting a Debug Session
+----------------------------
+If you're not familiar with gdb, you follow these step-by-step instructions.
+These instructions are NOT the only way to start a debug session, but they
+cover most of the individual functions to get you started.
+
+	1.  Start the JTAG gdb server. Open a Nios shell window and start
+	the server. When the server is started you must provide the base
+	address of the OCI core. For example, when using the Cyclone
+	development kit (DK1C20):
+
+		$ nios-gdb-server --ocibase=0x00920800 --tcpport=2342
+
+	2.  Start gdb. Open a Nios shell window, change to the top-level
+	U-Boot directory and start gdb, specifying the u-boot elf file:
+
+		$ nios-elf-gdb u-boot
+
+	3.  Update target settings. From the file menu, select
+	"Target Settings ..." and select the following, then click 'Ok':
+
+		Target:	Remote/TCP
+		Port :	2342   (same as in step 1)
+		Display download dialog: checked
+		All other check boxes: unchecked
+
+	4.  Connect to the target. Select menu: 'Run->Connect to target'.
+	You should see a dialog box indicating the you successfully connected
+	to the target.
+
+	5.  Download U-Boot. Select menu: 'Run->Download'.
+
+	6.  Open a gdb console window and set the source directory paths.
+	Select menu: 'View->Console'. In the console window, enter the
+	following commands, then close the console window:
+
+		(gdb) directory common
+		(gdb) directory cpu/nios
+		(gdb) directory lib_nios
+		(gdb) directory board/altera/dk1c20
+
+	Note that the last command is for the DK1C20 board only. If you
+	are using another board, specify that board's directory.
+
+	7.  Open the file board.c (using the file menu in the lower
+	left hand corner). Scroll to the board_init() routine and set
+	a breakpoint.
+
+	8. Run U-Boot. Just click on the run icon, or select menu:
+	'Run->Run'. U-Boot should start running, then break at your
+	breakpoint.
+
+	9.  Have fun & start learning more about gdb.
+
+
+5.3 For advanced Users
+----------------------
+A few notes for those more familiar with gdb.
+
+	-Serial port stubs are not implemented. Sorry, but it's just not
+	worth _my_ effort. The JTAG stubs work great and are ridiculously
+	simple to implement.
+
+	-If you need to debug the early startup code (prior to the vector
+	table initialization), use the nios-console debugger.
+
+	- Connect, download & run -- there are some problems here. Connect
+	download and run seperately to avoid trouble.
+
+6. BRAIN DAMAGE
 ----------------
 
 This section describes some of the unfortunate and avoidable aspects
 of working with the Nios CPU ... and some things you can do to
 reduce your pain.
 
-5.1 GERMS doesn't work with Hyperterminal
+6.1 GERMS doesn't work with Hyperterminal
 ------------------------------------------
 GERMS doesn't do CR/LF mapping that is compatible with Hyperterminal
 (or minicom) -- geez. Regardless of you opion of Hyperterminal, this
 sad design decision is remedied by using U-Boot.
 
-5.2 cygwin Incompatibility
+6.2 cygwin Incompatibility
 ---------------------------
 The version of cygwin distributed with the nios GNUPro toolchain is
 out-of-date and incompatible with the latest cygwin distributions.
@@ -202,7 +301,7 @@ topic).
 The solution ... well, you can wait for Altera ... or build as
 set of tools for linux.
 
-5.3 No native gcc
+6.3 No native gcc
 ------------------
 I'm not sure how this one slipped through the cracks ... but it is
 a real pain. Basically, if you want to build anything for the native
@@ -215,7 +314,7 @@ distro. Anybody who wants to use an already precompiled NIOS cross
 toolchain can it found in the CDK4NIOS project hosted by Source
 Forge at http://cdk4nios.sourceforge.net.
 
-5.4 Can't build default U-Boot
+6.4 Can't build default U-Boot
 -------------------------------
 By default, when you build U-Boot you will be building some native
 tools along with the target elf, bin, and srec files. Without a
@@ -232,15 +331,16 @@ environment.o: environment.c ../tools/envcrc
 		-c -o $@ environment.c
 
 With:
-environment.o: environment.c ../tools/envcrc
+environment.o: environment.c
 	$(CC) $(AFLAGS) -Wa,--no-warn \
 		-DENV_CRC=0 \
 		-c -o $@ environment.c
 
-BTW, thats a 'zero' ... not the letter 'O'.
+BTW, thats a 'zero' ... not the letter 'O'. And not that the
+"../tools/envcrc" dependency is removed.
 
 
-6. HELP WANTED
+7. HELP WANTED
 ---------------
 
 There are plenty of areas where help is needed. Here's are some ideas