Patches by Jon Loeliger, 24 Aug 2004:

- Add support for the MPC8541 and MPC8555 CDS boards
- Cleanup eth?addr handling: make dependent on CONFIG_ETH?ADDR

2 files changed, 190 insertions, 3 deletions

diff --git a/doc/README.mpc85xxads b/doc/README.mpc85xxads
index 146cff5521..939de20e8f 100644
--- a/doc/README.mpc85xxads
+++ b/doc/README.mpc85xxads
@@ -7,7 +7,7 @@ Updated 13-July-2004 Jon Loeliger
 0. Toolchain
 
     The Binutils in current ELDK toolchain will not support MPC85xx
-    chip.  You need use the newest binutils-2.14.tar.bz2 from
+    chip.  You need to use binutils-2.14.tar.bz2 (or newer) from
     http://ftp.gnu.org/gnu/binutils.
 
     The 8540/8560 ADS code base is known to compile using:
@@ -191,10 +191,10 @@ straightforward.
 
 4.4 Reflash U-boot Image using U-boot
 
-    => tftp 0 u-boot.bin
+    => tftp 10000 u-boot.bin
     => protect off fff80000 ffffffff
     => erase fff80000 ffffffff
-    => cp.b 0 fff80000 80000
+    => cp.b 10000 fff80000 80000
 
 
 4.5 Reflash U-Boot with a BDI-2000
diff --git a/doc/README.mpc85xxcds b/doc/README.mpc85xxcds
new file mode 100644
index 0000000000..06b1e9862e
--- /dev/null
+++ b/doc/README.mpc85xxcds
@@ -0,0 +1,187 @@
+Motorola MPC85xxCDS boards
+--------------------------
+
+The CDS family of boards consists of a PCI backplane called the
+"Arcadia", a PCI-form-factor carrier card that plugs into a PCI slot,
+and a CPU daughter card that bolts onto the daughter card.
+
+Much of the content of the README.mpc85xxads for the 85xx ADS boards
+applies to the 85xx CDS boards as well.  In particular the toolchain,
+the switch nomenclature, and the basis for the memory map.  There are
+some differences, though.
+
+
+Building U-Boot
+---------------
+
+The Binutils in current ELDK toolchain will not support MPC85xx
+chip.  You need to use binutils-2.14.tar.bz2 (or newer) from
+    http://ftp.gnu.org/gnu/binutils.
+
+The 85xx CDS code base is known to compile using:
+    gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)
+
+
+Memory Map
+----------
+
+The memory map for u-boot and linux has been extended w.r.t. the ADS
+platform to allow for utilization of all 85xx CDS devices.  The memory
+map is setup for linux to operate properly.  The linux source when
+configured for MPC85xx CDS has been updated to reflect the new memory
+map.
+
+The mapping is:
+
+   0x0000_0000     0x7fff_ffff     DDR                     2G
+   0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
+   0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+   0xe000_0000     0xe00f_ffff     CCSR                    1M
+   0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
+   0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
+   0xf000_0000     0xf7ff_ffff     SDRAM                   128M
+   0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
+   0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
+   0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
+
+   (*) The system control registers (CADMUS) start at offset 0xfdb0_4000
+   within the NVRAM/CADMUS region of memory.
+
+
+Using Flash
+-----------
+
+The CDS board  has two flash banks, each 8MB in size (2^23 = 0x00800000).
+There is a switch which allows the boot-bank to be selected.  The switch
+settings for updating flash are given below.
+
+The u-boot commands for copying the boot-bank into the secondary bank are
+as follows:
+
+     erase ff780000 ff7fffff
+     cp.b fff80000 ff780000 80000
+
+
+U-boot/kermit commands for downloading an image, then copying
+it into the secondary bank:
+
+     loadb
+     [Drop to kermit:
+        ^\c
+        send <u-boot-bin-image>
+        c
+     ]
+
+     erase ff780000 ff7fffff
+     cp.b $loadaddr ff780000 80000
+
+
+U-boot commands for downloading an image via tftp and flashing
+it into the second bank:
+
+     tftp 10000 <u-boot.bin.image>
+     erase ff780000 ff7fffff
+     cp.b 10000 ff780000 80000
+
+
+After copying the image into the second bank of flash, be sure to toggle
+SW2[2] on the carrier card before resetting the board in order to set the
+secondary bank as the boot-bank.
+
+
+Carrier Board Switches
+----------------------
+
+As a reminder, you should read the README.mpc85xxads too.
+
+Most switches on the carrier board should not be changed.  The only
+user-settable switches on the carrier board are used to configure
+the flash banks and determining the PCI slot.
+
+The first two bits of SW2 control how flash is used on the board:
+
+      12345678
+      --------
+  SW2=00XXXXXX     FLASH:  Boot bank 1, bank 2 available.
+      01XXXXXX     FLASH:  Boot bank 2, bank 1 available (swapped).
+      10XXXXXX     FLASH:  Boot promjet, bank 1 available
+      11XXXXXX     FLASH:  Boot promjet, bank 2 available
+
+The boot bank is always mapped to FF80_0000 and listed first by
+the "flinfo" command.  The secondary bank is always FF00_0000.
+
+When using PCI, linux needs to know to which slot the CDS carrier is
+connected..  By convention, the user-specific bits of SW2 are used to
+convey this information:
+
+      12345678
+      --------
+  SW2=xxxxxx00     PCI SLOT INFORM: The CDS carrier is in slot0 of the Arcadia
+      xxxxxx01     PCI SLOT INFORM: The CDS carrier is in slot1 of the Arcadia
+      xxxxxx10     PCI SLOT INFORM: The CDS carrier is in slot2 of the Arcadia
+      xxxxxx11     PCI SLOT INFORM: The CDS carrier is in slot3 of the Arcadia
+
+These are cleverly, er, clearly silkscreened as Slot 1 through 4,
+respectively, on the Arcadia near the support posts.
+
+
+The default setting of all switches on the carrier board is:
+
+      12345678
+      --------
+  SW1=01101100
+  SW2=0x1111yy     x=Flash bank, yy=PCI slot
+  SW3=11101111
+  SW4=10001000
+
+
+CPU Card Switches
+-----------------
+
+Most switches on the CPU Card should not be changed.  However, the
+frequency can be changed by setting SW3:
+
+      12345678
+      --------
+  SW3=XX00XXXX == CORE:CCB 2:1
+      XX01XXXX == CORE:CCB 5:2
+      XX10XXXX == CORE:CCB 3:1
+      XX11XXXX == CORE:CCB 7:2
+      XXXX1000 == CCB:SYSCLK 8:1
+      XXXX1010 == CCB:SYSCLK 10:1
+
+A safe default setting for all switches on the CPU board is:
+
+      12345678
+      --------
+  SW1=10001111
+  SW2=01000111
+  SW3=00001000
+  SW4=11111110
+
+
+eDINK Info
+----------
+
+One bank of flash may contain an eDINK image.
+
+Memory Map:
+
+   CCSRBAR @ 0xe0000000
+   Flash Bank 1 @ 0xfe000000
+   Flash Bank 2 @ 0xff000000
+   Ram @ 0
+
+Commands for downloading a u-boot image to memory from edink:
+
+   env -c
+   time -s 4/8/2004 4:30p
+   dl -k -b -o 100000
+   [Drop to kermit:
+        ^\c
+        transmit /binary <u-boot-bin-image>
+        c
+   ]
+
+   fu -l 100000 fe780000 80000
+