[PCS440EP] upgrade the PCS440EP board:

                - Show on the Status LEDs, some States of the board.
                - Get the MAC addresses from the EEProm
                - use PREBOOT
                - use the CF on the board.
                - check the U-Boot image in the Flash with a SHA1
                  checksum.
                - use dynamic TLB entries generation for the SDRAM

Signed-off-by: Heiko Schocher <hs@denx.de>

1 files changed, 39 insertions, 32 deletions

diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c
index 48b9ee2f7e..d748daee01 100644
--- a/cpu/ppc4xx/44x_spd_ddr2.c
+++ b/cpu/ppc4xx/44x_spd_ddr2.c
@@ -129,6 +129,13 @@
 #define MY_TLB_WORD2_I_ENABLE	TLB_WORD2_I_ENABLE	/* disable caching on SDRAM */
 #endif
 
+#if defined(CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG)
+extern void spd_ddr_init_hang (void);
+#define HANG()	spd_ddr_init_hang()
+#else
+#define HANG()	hang()
+#endif
+
 /* Private Structure Definitions */
 
 /* enum only to ease code for cas latency setting */
@@ -582,7 +589,7 @@ static void get_spd_info(unsigned long *dimm_populated,
 
 	if (dimm_found == FALSE) {
 		printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n");
-		hang();
+		HANG();
 	}
 }
 
@@ -629,42 +636,42 @@ static void check_mem_type(unsigned long *dimm_populated,
 				       "slot %d.\n", (unsigned int)dimm_num);
 				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			case 2:
 				printf("ERROR: EDO DIMM detected in slot %d.\n",
 				       (unsigned int)dimm_num);
 				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			case 3:
 				printf("ERROR: Pipelined Nibble DIMM detected in slot %d.\n",
 				       (unsigned int)dimm_num);
 				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			case 4:
 				printf("ERROR: SDRAM DIMM detected in slot %d.\n",
 				       (unsigned int)dimm_num);
 				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			case 5:
 				printf("ERROR: Multiplexed ROM DIMM detected in slot %d.\n",
 				       (unsigned int)dimm_num);
 				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			case 6:
 				printf("ERROR: SGRAM DIMM detected in slot %d.\n",
 				       (unsigned int)dimm_num);
 				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			case 7:
 				debug("DIMM slot %d: DDR1 SDRAM detected\n", dimm_num);
@@ -679,7 +686,7 @@ static void check_mem_type(unsigned long *dimm_populated,
 				       (unsigned int)dimm_num);
 				printf("Only DDR1 and DDR2 SDRAM DIMMs are supported.\n");
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			}
 		}
@@ -689,7 +696,7 @@ static void check_mem_type(unsigned long *dimm_populated,
 		    && (dimm_populated[dimm_num]   != SDRAM_NONE)
 		    && (dimm_populated[dimm_num-1] != dimm_populated[dimm_num])) {
 			printf("ERROR: DIMM's DDR1 and DDR2 type can not be mixed.\n");
-			hang();
+			HANG();
 		}
 	}
 }
@@ -764,7 +771,7 @@ static void check_frequency(unsigned long *dimm_populated,
 				       (unsigned int)(calc_cycle_time*10));
 				printf("Replace the DIMM, or change DDR frequency via "
 				       "strapping bits.\n\n");
-				hang();
+				HANG();
 			}
 		}
 	}
@@ -796,7 +803,7 @@ static void check_rank_number(unsigned long *dimm_populated,
 				       "slot %d is not supported.\n", dimm_rank, dimm_num);
 				printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 			} else
 				total_rank += dimm_rank;
 		}
@@ -805,7 +812,7 @@ static void check_rank_number(unsigned long *dimm_populated,
 			       "for all slots.\n", (unsigned int)total_rank);
 			printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
 			printf("Remove one of the DIMM modules.\n\n");
-			hang();
+			HANG();
 		}
 	}
 }
@@ -830,28 +837,28 @@ static void check_voltage_type(unsigned long *dimm_populated,
 				printf("This DIMM is 5.0 Volt/TTL.\n");
 				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
 				       (unsigned int)dimm_num);
-				hang();
+				HANG();
 				break;
 			case 0x01:
 				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
 				printf("This DIMM is LVTTL.\n");
 				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
 				       (unsigned int)dimm_num);
-				hang();
+				HANG();
 				break;
 			case 0x02:
 				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
 				printf("This DIMM is 1.5 Volt.\n");
 				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
 				       (unsigned int)dimm_num);
-				hang();
+				HANG();
 				break;
 			case 0x03:
 				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
 				printf("This DIMM is 3.3 Volt/TTL.\n");
 				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
 				       (unsigned int)dimm_num);
-				hang();
+				HANG();
 				break;
 			case 0x04:
 				/* 2.5 Voltage only for DDR1 */
@@ -863,7 +870,7 @@ static void check_voltage_type(unsigned long *dimm_populated,
 				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
 				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
 				       (unsigned int)dimm_num);
-				hang();
+				HANG();
 				break;
 			}
 		}
@@ -1006,13 +1013,13 @@ static void program_copt1(unsigned long *dimm_populated,
 	if ((dimm_populated[0] != SDRAM_NONE) && (dimm_populated[1] != SDRAM_NONE)) {
 		if (buf0 != buf1) {
 			printf("ERROR: DIMM's buffered/unbuffered, registered, clocking don't match.\n");
-			hang();
+			HANG();
 		}
 	}
 
 	if ((dimm_64bit == TRUE) && (dimm_32bit == TRUE)) {
 		printf("ERROR: Cannot mix 32 bit and 64 bit DDR-SDRAM DIMMs together.\n");
-		hang();
+		HANG();
 	}
 	else if ((dimm_64bit == TRUE) && (dimm_32bit == FALSE)) {
 		mcopt1 |= SDRAM_MCOPT1_DMWD_64;
@@ -1020,7 +1027,7 @@ static void program_copt1(unsigned long *dimm_populated,
 		mcopt1 |= SDRAM_MCOPT1_DMWD_32;
 	} else {
 		printf("ERROR: Please install only 32 or 64 bit DDR-SDRAM DIMMs.\n\n");
-		hang();
+		HANG();
 	}
 
 	if (ecc_enabled == TRUE)
@@ -1209,7 +1216,7 @@ static void program_initplr(unsigned long *dimm_populated,
 			break;
 		default:
 			printf("ERROR: ucode error on selected_cas value %d", selected_cas);
-			hang();
+			HANG();
 			break;
 		}
 
@@ -1241,7 +1248,7 @@ static void program_initplr(unsigned long *dimm_populated,
 			break;
 		default:
 			printf("ERROR: write recovery not support (%d)", write_recovery);
-			hang();
+			HANG();
 			break;
 		}
 #else
@@ -1259,7 +1266,7 @@ static void program_initplr(unsigned long *dimm_populated,
 			ods = ODS_REDUCED;
 		} else {
 			printf("ERROR: Unsupported number of DIMM's (%d)", total_dimm);
-			hang();
+			HANG();
 		}
 
 		mr = CMD_EMR | SELECT_MR | BURST_LEN_4 | wr | cas;
@@ -1284,7 +1291,7 @@ static void program_initplr(unsigned long *dimm_populated,
 		mtsdram(SDRAM_INITPLR13, 0x80800000 | emr);		/* EMR OCD Exit */
 	} else {
 		printf("ERROR: ucode error as unknown DDR type in program_initplr");
-		hang();
+		HANG();
 	}
 }
 
@@ -1389,7 +1396,7 @@ static void program_mode(unsigned long *dimm_populated,
 					} else {
 						printf("ERROR: SPD reported Tcyc is incorrect for DIMM "
 						       "in slot %d\n", (unsigned int)dimm_num);
-						hang();
+						HANG();
 					}
 				} else {
 					/* Convert from hex to decimal */
@@ -1526,7 +1533,7 @@ static void program_mode(unsigned long *dimm_populated,
 			printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n");
 			printf("Only DIMMs DDR1 with CAS latencies of 2.0, 2.5, and 3.0 are supported.\n");
 			printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n");
-			hang();
+			HANG();
 		}
 	} else { /* DDR2 */
 		debug("cas_3_0_available=%d\n", cas_3_0_available);
@@ -1549,7 +1556,7 @@ static void program_mode(unsigned long *dimm_populated,
 			       cas_3_0_available, cas_4_0_available, cas_5_0_available);
 			printf("sdram_freq=%d cycle3=%d cycle4=%d cycle5=%d\n\n",
 			       sdram_freq, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk);
-			hang();
+			HANG();
 		}
 	}
 
@@ -1658,7 +1665,7 @@ static void program_rtr(unsigned long *dimm_populated,
 				printf("ERROR: DIMM %d unsupported refresh rate/type.\n",
 				       (unsigned int)dimm_num);
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 				break;
 			}
 
@@ -2066,7 +2073,7 @@ static void program_bxcf(unsigned long *dimm_populated,
 					printf("ERROR: Unsupported value for number of "
 					       "column addresses: %d.\n", (unsigned int)num_col_addr);
 					printf("Replace the DIMM module with a supported DIMM.\n\n");
-					hang();
+					HANG();
 				}
 			}
 
@@ -2148,7 +2155,7 @@ static void program_memory_queue(unsigned long *dimm_populated,
 				printf("ERROR: Unsupported value for the banksize: %d.\n",
 				       (unsigned int)rank_size_id);
 				printf("Replace the DIMM module with a supported DIMM.\n\n");
-				hang();
+				HANG();
 			}
 
 			if ((dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_num == 1))
@@ -2693,7 +2700,7 @@ calibration_loop:
 		printf("\nERROR: Cannot determine a common read delay for the "
 		       "DIMM(s) installed.\n");
 		debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__);
-		hang();
+		HANG();
 	}
 
 	blank_string(strlen(str));
@@ -2849,7 +2856,7 @@ static void test(void)
 	if (window_found == FALSE) {
 		printf("ERROR: Cannot determine a common read delay for the "
 		       "DIMM(s) installed.\n");
-		hang();
+		HANG();
 	}
 
 	/*------------------------------------------------------------------