OMAP5-uevm: USB: Add xHCI host contoller support

Add the call back into the board file for to enable
the SMPS10 VBUS regulator.

Signed-off-by: Dan Murphy <dmurphy@ti.com>

1 files changed, 51 insertions, 23 deletions

diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c
index 47063309e5..5fc3473ecc 100644
--- a/board/ti/omap5_uevm/evm.c
+++ b/board/ti/omap5_uevm/evm.c
@@ -14,7 +14,7 @@
 
 #include "mux_data.h"
 
-#ifdef CONFIG_USB_EHCI
+#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP)
 #include <usb.h>
 #include <asm/gpio.h>
 #include <asm/arch/clock.h>
@@ -72,6 +72,35 @@ int board_eth_init(bd_t *bis)
 	return 0;
 }
 
+#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP)
+static void enable_host_clocks(void)
+{
+	int auxclk;
+	int hs_clk_ctrl_val = (OPTFCLKEN_HSIC60M_P3_CLK |
+				OPTFCLKEN_HSIC480M_P3_CLK |
+				OPTFCLKEN_HSIC60M_P2_CLK |
+				OPTFCLKEN_HSIC480M_P2_CLK |
+				OPTFCLKEN_UTMI_P3_CLK | OPTFCLKEN_UTMI_P2_CLK);
+
+	/* Enable port 2 and 3 clocks*/
+	setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, hs_clk_ctrl_val);
+
+	/* Enable port 2 and 3 usb host ports tll clocks*/
+	setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl,
+			(OPTFCLKEN_USB_CH1_CLK_ENABLE | OPTFCLKEN_USB_CH2_CLK_ENABLE));
+#ifdef CONFIG_USB_XHCI_OMAP
+	/* Enable the USB OTG Super speed clocks */
+	setbits_le32((*prcm)->cm_l3init_usb_otg_ss_clkctrl,
+			(OPTFCLKEN_REFCLK960M | OTG_SS_CLKCTRL_MODULEMODE_HW));
+#endif
+
+	auxclk = readl((*prcm)->scrm_auxclk1);
+	/* Request auxilary clock */
+	auxclk |= AUXCLK_ENABLE_MASK;
+	writel(auxclk, (*prcm)->scrm_auxclk1);
+}
+#endif
+
 /**
  * @brief misc_init_r - Configure EVM board specific configurations
  * such as power configurations, ethernet initialization as phase2 of
@@ -84,6 +113,7 @@ int misc_init_r(void)
 #ifdef CONFIG_PALMAS_POWER
 	palmas_init_settings();
 #endif
+
 	return 0;
 }
 
@@ -129,26 +159,9 @@ static struct omap_usbhs_board_data usbhs_bdata = {
 	.port_mode[2] = OMAP_EHCI_PORT_MODE_HSIC,
 };
 
-static void enable_host_clocks(void)
-{
-	int hs_clk_ctrl_val = (OPTFCLKEN_HSIC60M_P3_CLK |
-				OPTFCLKEN_HSIC480M_P3_CLK |
-				OPTFCLKEN_HSIC60M_P2_CLK |
-				OPTFCLKEN_HSIC480M_P2_CLK |
-				OPTFCLKEN_UTMI_P3_CLK | OPTFCLKEN_UTMI_P2_CLK);
-
-	/* Enable port 2 and 3 clocks*/
-	setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, hs_clk_ctrl_val);
-
-	/* Enable port 2 and 3 usb host ports tll clocks*/
-	setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl,
-			(OPTFCLKEN_USB_CH1_CLK_ENABLE | OPTFCLKEN_USB_CH2_CLK_ENABLE));
-}
-
 int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
 {
 	int ret;
-	int auxclk;
 	int reg;
 	uint8_t device_mac[6];
 
@@ -171,11 +184,6 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
 		eth_setenv_enetaddr("usbethaddr", device_mac);
 	}
 
-	auxclk = readl((*prcm)->scrm_auxclk1);
-	/* Request auxilary clock */
-	auxclk |= AUXCLK_ENABLE_MASK;
-	writel(auxclk, (*prcm)->scrm_auxclk1);
-
 	ret = omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
 	if (ret < 0) {
 		puts("Failed to initialize ehci\n");
@@ -203,3 +211,23 @@ void usb_hub_reset_devices(int port)
 	}
 }
 #endif
+
+#ifdef CONFIG_USB_XHCI_OMAP
+/**
+ * @brief board_usb_init - Configure EVM board specific configurations
+ * for the LDO's and clocks for the USB blocks.
+ *
+ * @return 0
+ */
+int board_usb_init(void)
+{
+	int ret;
+#ifdef CONFIG_PALMAS_USB_SS_PWR
+	ret = palmas_enable_ss_ldo();
+#endif
+
+	enable_host_clocks();
+
+	return 0;
+}
+#endif