m68k: Remove M5271EVB and idmr board support

CONFIG_SYS_HZ must be always 1000, but M5271EVB.h defines it
as 1000000 and idmr.h defines it as (50000000 / 64).

When compiling these two boards, a warning message is displayed:

  time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000
  and should not be defined by platforms" [-Wcpp]

There are no board maintainers for them so this commit just
deletes them.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>

4 files changed, 0 insertions, 217 deletions

diff --git a/board/freescale/m5271evb/Makefile b/board/freescale/m5271evb/Makefile
deleted file mode 100644
index 77138c6073..0000000000
--- a/board/freescale/m5271evb/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= m5271evb.o
diff --git a/board/freescale/m5271evb/config.mk b/board/freescale/m5271evb/config.mk
deleted file mode 100644
index 957f584887..0000000000
--- a/board/freescale/m5271evb/config.mk
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-# Coldfire contribution by Bernhard Kuhn <bkuhn@metrowerks.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-CONFIG_SYS_TEXT_BASE = 0xffe00000
diff --git a/board/freescale/m5271evb/m5271evb.c b/board/freescale/m5271evb/m5271evb.c
deleted file mode 100644
index 5981a2711a..0000000000
--- a/board/freescale/m5271evb/m5271evb.c
+++ /dev/null
@@ -1,115 +0,0 @@
-/*
- * (C) Copyright 2000-2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/immap.h>
-
-int checkboard (void) {
-	puts ("Board: Freescale M5271EVB\n");
-	return 0;
-};
-
-phys_size_t initdram (int board_type) {
-
-	int i;
-
-	/* Enable Address lines 23-21 and lower 16bits of data path */
-	mbar_writeByte(MCF_GPIO_PAR_AD, MCF_GPIO_AD_ADDR23 |
-			MCF_GPIO_AD_ADDR22 | MCF_GPIO_AD_ADDR21 |
-			MCF_GPIO_AD_DATAL);
-
-	/* Set CS2 pin to be SD_CS0 */
-	mbar_writeByte(MCF_GPIO_PAR_CS, mbar_readByte(MCF_GPIO_PAR_CS)
-			| MCF_GPIO_PAR_CS_PAR_CS2);
-
-	/* Configure SDRAM Control Pin Assignemnt Register */
-	mbar_writeByte(MCF_GPIO_PAR_SDRAM, MCF_GPIO_SDRAM_CSSDCS_00 |
-			MCF_GPIO_SDRAM_SDWE | MCF_GPIO_SDRAM_SCAS |
-			MCF_GPIO_SDRAM_SRAS | MCF_GPIO_SDRAM_SCKE |
-			MCF_GPIO_SDRAM_SDCS_11);
-	asm(" nop");
-
-	/*
-	 * Check to see if the SDRAM has already been initialized
-	 * by a run control tool
-	 */
-	if (!(mbar_readLong(MCF_SDRAMC_DACR0) & MCF_SDRAMC_DACRn_RE)) {
-		/* Initialize DRAM Control Register: DCR */
-		mbar_writeShort(MCF_SDRAMC_DCR,
-				MCF_SDRAMC_DCR_RTIM(2)
-				| MCF_SDRAMC_DCR_RC(0x2E));
-		asm(" nop");
-
-		/*
-		 * Initialize DACR0
-		 *
-		 * CASL: 01
-		 * CBM: cmd at A20, bank select bits 21 and up
-		 * PS: 32bit port size
-		 */
-		mbar_writeLong(MCF_SDRAMC_DACR0,
-				MCF_SDRAMC_DACRn_BA(CONFIG_SYS_SDRAM_BASE>>18)
-				| MCF_SDRAMC_DACRn_CASL(1)
-				| MCF_SDRAMC_DACRn_CBM(3)
-				| MCF_SDRAMC_DACRn_PS(0));
-		asm(" nop");
-
-		/* Initialize DMR0 */
-		mbar_writeLong(MCF_SDRAMC_DMR0,
-				MCF_SDRAMC_DMRn_BAM_16M
-				| MCF_SDRAMC_DMRn_V);
-		asm(" nop");
-
-		/* Set IP bit in DACR */
-		mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
-				| MCF_SDRAMC_DACRn_IP);
-		asm(" nop");
-
-		/* Wait at least 20ns to allow banks to precharge */
-		for (i = 0; i < 5; i++)
-			asm(" nop");
-
-		/* Write to this block to initiate precharge */
-		*(u32 *)(CONFIG_SYS_SDRAM_BASE) = 0xa5a5a5a5;
-		asm(" nop");
-
-		/* Set RE bit in DACR */
-		mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
-				| MCF_SDRAMC_DACRn_RE);
-
-		/* Wait for at least 8 auto refresh cycles to occur */
-		for (i = 0; i < 2000; i++)
-			asm(" nop");
-
-		/* Finish the configuration by issuing the MRS */
-		mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
-				| MCF_SDRAMC_DACRn_MRS);
-		asm(" nop");
-
-		/*
-		 * Write to the SDRAM Mode Register A0-A11 = 0x400
-		 *
-		 * Write Burst Mode = Programmed Burst Length
-		 * Op Mode = Standard Op
-		 * CAS Latency = 2
-		 * Burst Type = Sequential
-		 * Burst Length = 1
-		 */
-		*(u32 *)(CONFIG_SYS_SDRAM_BASE + 0x400) = 0xa5a5a5a5;
-		asm(" nop");
-	}
-
-	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-};
-
-int testdram (void) {
-
-	/* TODO: XXX XXX XXX */
-	printf ("DRAM test not implemented!\n");
-
-	return (0);
-}
diff --git a/board/freescale/m5271evb/u-boot.lds b/board/freescale/m5271evb/u-boot.lds
deleted file mode 100644
index 3defcd25c1..0000000000
--- a/board/freescale/m5271evb/u-boot.lds
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(m68k)
-
-SECTIONS
-{
-  .text      :
-  {
-    arch/m68k/cpu/mcf52x2/start.o		(.text*)
-
-    . = DEFINED(env_offset) ? env_offset : .;
-    common/env_embedded.o	(.ppcenv)
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-
-  .reloc   :
-  {
-    __got_start = .;
-    KEEP(*(.got))
-    __got_end = .;
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  . = ALIGN(4);
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)      :
-  {
-   _sbss = .;
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-   _ebss = .;
-  }
-  __bss_end = . ;
-  PROVIDE (end = .);
-}