powerpc/p2041rdb: Add p2041rdb board support

P2041RDB Specification:
-----------------------
Memory subsystem:
 * 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 256 Kbit M24256 I2C EEPROM
 * 16 Mbyte SPI memory
 * SD connector to interface with the SD memory card

Ethernet:
 * dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
 * dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
 * dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)

PCIe:
 * Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 * Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2

SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors

USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces

I2C:
 * I2C1: Real time clock, Temperature sensor, Memory module
 * I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

1 files changed, 115 insertions, 0 deletions

diff --git a/board/freescale/p2041rdb/ddr.c b/board/freescale/p2041rdb/ddr.c
new file mode 100644
index 0000000000..46de9109da
--- /dev/null
+++ b/board/freescale/p2041rdb/ddr.c
@@ -0,0 +1,115 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+typedef struct {
+	u32 datarate_mhz_low;
+	u32 datarate_mhz_high;
+	u32 n_ranks;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2T;
+} board_specific_parameters_t;
+
+/*
+ * ranges for parameters:
+ *  wr_data_delay = 0-6
+ *  clk adjust = 0-8
+ *  cpo 2-0x1E (30)
+ */
+const board_specific_parameters_t board_specific_parameters[] = {
+	/*
+	 * memory controller 0
+	 *  lo|  hi|  num|  clk| wrlvl | cpo  |wrdata|2T
+	 * mhz| mhz|ranks|adjst| start | delay|
+	 */
+	{  1017, 1116,    2,    4,     6,   0xff,    2,  0},
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const board_specific_parameters_t *pbsp =
+				&board_specific_parameters[0];
+	u32 num_params = ARRAY_SIZE(board_specific_parameters);
+	u32 i;
+	ulong ddr_freq;
+
+	/*
+	 * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	for (i = 0; i < num_params; i++) {
+		if (ddr_freq >= pbsp->datarate_mhz_low &&
+			ddr_freq <= pbsp->datarate_mhz_high &&
+			pdimm[0].n_ranks == pbsp->n_ranks) {
+			popts->cpo_override = pbsp->cpo;
+			popts->write_data_delay = pbsp->write_data_delay;
+			popts->clk_adjust = pbsp->clk_adjust;
+			popts->wrlvl_start = pbsp->wrlvl_start;
+			popts->twoT_en = pbsp->force_2T;
+			break;
+		}
+		pbsp++;
+	}
+
+	if (i == num_params) {
+		printf("Warning: board specific timing not found "
+			"for data rate %lu MT/s!\n", ddr_freq);
+	}
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/* Write leveling override */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/* Rtt and Rtt_WR override */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 60 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN;
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size = 0;
+
+	puts("Initializing....");
+
+	if (fsl_use_spd()) {
+		puts("using SPD\n");
+		dram_size = fsl_ddr_sdram();
+	} else {
+		puts("no SPD and fixed parameters\n");
+		return dram_size;
+	}
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
+
+	puts("    DDR: ");
+	return dram_size;
+}