mpc8xx: remove fads board support

These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

5 files changed, 2 insertions, 109 deletions

diff --git a/arch/powerpc/cpu/mpc8xx/cpu.c b/arch/powerpc/cpu/mpc8xx/cpu.c
index 5c96b5fe16..eb4432f6d7 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu.c
@@ -97,14 +97,8 @@ static int check_CPU (long clock, uint pvr, uint immr)
 		pre = 'M'; m = 1;
 		if (id_str == NULL)
 			id_str =
-# if defined(CONFIG_MPC852T)
-		"PC852T";
-# elif defined(CONFIG_MPC859T)
+# if defined(CONFIG_MPC859T)
 		"PC859T";
-# elif defined(CONFIG_MPC859DSL)
-		"PC859DSL";
-# elif defined(CONFIG_MPC866T)
-		"PC866T";
 # else
 		"PC866x"; /* Unknown chip from MPC866 family */
 # endif
diff --git a/arch/powerpc/cpu/mpc8xx/fec.c b/arch/powerpc/cpu/mpc8xx/fec.c
index ccb460ef96..d12b3df4a1 100644
--- a/arch/powerpc/cpu/mpc8xx/fec.c
+++ b/arch/powerpc/cpu/mpc8xx/fec.c
@@ -542,32 +542,6 @@ static int fec_init (struct eth_device *dev, bd_t * bd)
 		(volatile fec_t *) (CONFIG_SYS_IMMR + efis->fecp_offset);
 	int i;
 
-	if (efis->ether_index == 0) {
-#if defined(CONFIG_FADS)	/* FADS family uses FPGA (BCSR) to control PHYs */
-#if defined(CONFIG_MPC885ADS)
-		*(vu_char *) BCSR5 &= ~(BCSR5_MII1_EN | BCSR5_MII1_RST);
-#else
-		/* configure FADS for fast (FEC) ethernet, half-duplex */
-		/* The LXT970 needs about 50ms to recover from reset, so
-		 * wait for it by discovering the PHY before leaving eth_init().
-		 */
-		{
-			volatile uint *bcsr4 = (volatile uint *) BCSR4;
-
-			*bcsr4 = (*bcsr4 & ~(BCSR4_FETH_EN | BCSR4_FETHCFG1))
-				| (BCSR4_FETHCFG0 | BCSR4_FETHFDE |
-				   BCSR4_FETHRST);
-
-			/* reset the LXT970 PHY */
-			*bcsr4 &= ~BCSR4_FETHRST;
-			udelay (10);
-			*bcsr4 |= BCSR4_FETHRST;
-			udelay (10);
-		}
-#endif /* CONFIG_MPC885ADS */
-#endif /* CONFIG_FADS */
-	}
-
 #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
 	/* the MII interface is connected to FEC1
 	 * so for the miiphy_xxx function to work we must
diff --git a/arch/powerpc/cpu/mpc8xx/scc.c b/arch/powerpc/cpu/mpc8xx/scc.c
index 7ed98b879f..01029ff68a 100644
--- a/arch/powerpc/cpu/mpc8xx/scc.c
+++ b/arch/powerpc/cpu/mpc8xx/scc.c
@@ -197,19 +197,6 @@ static int scc_init (struct eth_device *dev, bd_t * bis)
 	reset_phy();
 #endif
 
-#ifdef CONFIG_FADS
-#if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC860T)
-	/* The MPC86xADS/FADS860T don't use the MODEM_EN or DATA_VOICE signals. */
-	*((uint *) BCSR4) &= ~BCSR4_ETHLOOP;
-	*((uint *) BCSR4) |= BCSR4_TFPLDL | BCSR4_TPSQEL;
-	*((uint *) BCSR1) &= ~BCSR1_ETHEN;
-#else
-	*((uint *) BCSR4) &= ~(BCSR4_ETHLOOP | BCSR4_MODEM_EN);
-	*((uint *) BCSR4) |= BCSR4_TFPLDL | BCSR4_TPSQEL | BCSR4_DATA_VOICE;
-	*((uint *) BCSR1) &= ~BCSR1_ETHEN;
-#endif
-#endif
-
 	pram_ptr = (scc_enet_t *) & (immr->im_cpm.cp_dparam[PROFF_ENET]);
 
 	rxIdx = 0;
@@ -488,13 +475,6 @@ static int scc_init (struct eth_device *dev, bd_t * bis)
 	immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |=
 		(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
 
-	/*
-	 * Work around transmit problem with first eth packet
-	 */
-#if defined (CONFIG_FADS)
-	udelay (10000);		/* wait 10 ms */
-#endif
-
 	return 1;
 }
 
diff --git a/arch/powerpc/cpu/mpc8xx/serial.c b/arch/powerpc/cpu/mpc8xx/serial.c
index 802d4f1ca8..b1625fba16 100644
--- a/arch/powerpc/cpu/mpc8xx/serial.c
+++ b/arch/powerpc/cpu/mpc8xx/serial.c
@@ -173,15 +173,6 @@ static int smc_init (void)
 # endif
 #endif
 
-#if defined(CONFIG_FADS)
-	/* Enable RS232 */
-#if defined(CONFIG_8xx_CONS_SMC1)
-	*((uint *) BCSR1) &= ~BCSR1_RS232EN_1;
-#else
-	*((uint *) BCSR1) &= ~BCSR1_RS232EN_2;
-#endif
-#endif	/* CONFIG_FADS */
-
 	/* Set the physical address of the host memory buffers in
 	 * the buffer descriptors.
 	 */
diff --git a/arch/powerpc/cpu/mpc8xx/video.c b/arch/powerpc/cpu/mpc8xx/video.c
index fc351585be..2fd5b11fe4 100644
--- a/arch/powerpc/cpu/mpc8xx/video.c
+++ b/arch/powerpc/cpu/mpc8xx/video.c
@@ -798,22 +798,6 @@ static void video_encoder_init (void)
 	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 #endif
 
-#ifdef CONFIG_FADS
-	/* Reset ADV7176 chip */
-	debug ("[VIDEO ENCODER] Resetting encoder...\n");
-	(*(int *) BCSR4) &= ~(1 << 21);
-
-	/* Wait for 5 ms inside the reset */
-	debug ("[VIDEO ENCODER] Waiting for encoder reset...\n");
-	udelay (5000);
-
-	/* Take ADV7176 out of reset */
-	(*(int *) BCSR4) |= 1 << 21;
-
-	/* Wait for 5 ms after the reset */
-	udelay (5000);
-#endif	/* CONFIG_FADS */
-
 	/* Send configuration */
 #ifdef DEBUG
 	{
@@ -860,16 +844,6 @@ static void video_ctrl_init (void *memptr)
 	debug ("[VIDEO CTRL] Turning off video controller...\n");
 	SETBIT (immap->im_vid.vid_vccr, VIDEO_VCCR_VON, 0);
 
-#ifdef CONFIG_FADS
-	/* Turn on Video Port LED */
-	debug ("[VIDEO CTRL] Turning off video port led...\n");
-	SETBIT (*(int *) BCSR4, VIDEO_BCSR4_VIDLED_BIT, 1);
-
-	/* Disable internal clock */
-	debug ("[VIDEO CTRL] Disabling internal clock...\n");
-	SETBIT (*(int *) BCSR4, VIDEO_BCSR4_EXTCLK_BIT, 0);
-#endif
-
 	/* Generate and make active a new video mode */
 	debug ("[VIDEO CTRL] Generating video mode...\n");
 	video_mode_generate ();
@@ -892,15 +866,6 @@ static void video_ctrl_init (void *memptr)
 	immap->im_ioport.iop_pdpar = 0x1fff;
 	immap->im_ioport.iop_pddir = 0x0000;
 
-#ifdef CONFIG_FADS
-	/* Turn on Video Port Clock - ONLY AFTER SET VCCR TO ENABLE EXTERNAL CLOCK */
-	debug ("[VIDEO CTRL] Turning on video clock...\n");
-	SETBIT (*(int *) BCSR4, VIDEO_BCSR4_EXTCLK_BIT, 1);
-
-	/* Turn on Video Port LED */
-	debug ("[VIDEO CTRL] Turning on video port led...\n");
-	SETBIT (*(int *) BCSR4, VIDEO_BCSR4_VIDLED_BIT, 0);
-#endif
 #ifdef CONFIG_RRVISION
 	debug ("PC5->Output(1): enable PAL clock");
 	immap->im_ioport.iop_pcpar &= ~(0x0400);
@@ -1153,9 +1118,7 @@ static void *video_logo (void)
 {
 	u16 *screen = video_fb_address, width = VIDEO_COLS;
 #ifdef VIDEO_INFO
-# ifndef CONFIG_FADS
 	char temp[32];
-# endif
 	char info[80];
 #endif /* VIDEO_INFO */
 
@@ -1173,7 +1136,7 @@ static void *video_logo (void)
 	sprintf (info, "    Wolfgang DENK, wd@denx.de");
 	video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y + VIDEO_FONT_HEIGHT * 2,
 					info);
-#ifndef CONFIG_FADS		/* all normal boards */
+
 	/* leave one blank line */
 
 	sprintf(info, "MPC823 CPU at %s MHz, %ld MiB RAM, %ld MiB Flash",
@@ -1182,15 +1145,6 @@ static void *video_logo (void)
 		gd->bd->bi_flashsize >> 20 );
 	video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y + VIDEO_FONT_HEIGHT * 4,
 					info);
-#else				/* FADS :-( */
-	sprintf (info, "MPC823 CPU at 50 MHz on FADS823 board");
-	video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y + VIDEO_FONT_HEIGHT,
-					  info);
-
-	sprintf(info, "2MiB FLASH - 8MiB DRAM - 4MiB SRAM");
-	video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y + VIDEO_FONT_HEIGHT * 2,
-					  info);
-#endif
 #endif
 
 	return video_fb_address + VIDEO_LOGO_HEIGHT * VIDEO_LINE_LEN;