ARM: davinci: move SoC sources to mach-davinci

Move
arch/arm/cpu/arm926ejs/davinci/* -> arch/arm/mach-davinci/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>

1 files changed, 81 insertions, 0 deletions

diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c
new file mode 100644
index 0000000000..c58e271e28
--- /dev/null
+++ b/arch/arm/mach-davinci/dm644x.c
@@ -0,0 +1,81 @@
+/*
+ * SoC-specific code for tms320dm644x chips
+ *
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ * Copyright (C) 2008 Lyrtech <www.lyrtech.com>
+ * Copyright (C) 2004 Texas Instruments.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+
+#define PINMUX0_EMACEN (1 << 31)
+#define PINMUX0_AECS5  (1 << 11)
+#define PINMUX0_AECS4  (1 << 10)
+
+#define PINMUX1_I2C    (1 <<  7)
+#define PINMUX1_UART1  (1 <<  1)
+#define PINMUX1_UART0  (1 <<  0)
+
+
+void davinci_enable_uart0(void)
+{
+	lpsc_on(DAVINCI_LPSC_UART0);
+
+	/* Bringup UART0 out of reset */
+	REG(UART0_PWREMU_MGMT) = 0x00006001;
+
+	/* Enable UART0 MUX lines */
+	REG(PINMUX1) |= PINMUX1_UART0;
+}
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+void davinci_enable_emac(void)
+{
+	lpsc_on(DAVINCI_LPSC_EMAC);
+	lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
+	lpsc_on(DAVINCI_LPSC_MDIO);
+
+	/* Enable GIO3.3V cells used for EMAC */
+	REG(VDD3P3V_PWDN) = 0;
+
+	/* Enable EMAC. */
+	REG(PINMUX0) |= PINMUX0_EMACEN;
+}
+#endif
+
+#ifdef CONFIG_SYS_I2C_DAVINCI
+void davinci_enable_i2c(void)
+{
+	lpsc_on(DAVINCI_LPSC_I2C);
+
+	/* Enable I2C pin Mux */
+	REG(PINMUX1) |= PINMUX1_I2C;
+}
+#endif
+
+void davinci_errata_workarounds(void)
+{
+	/*
+	 * Workaround for TMS320DM6446 errata 1.3.22:
+	 *   PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset
+	 *   Revision(s) Affected: 1.3 and earlier
+	 */
+	REG(PSC_SILVER_BULLET) = 0;
+
+	/*
+	 * Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR)
+	 * as suggested in TMS320DM6446 errata 2.1.2:
+	 *
+	 * On DM6446 Silicon Revision 2.1 and earlier, under certain conditions
+	 * low priority modules can occupy the bus and prevent high priority
+	 * modules like the VPSS from getting the required DDR2 throughput.
+	 * A hex value of 0x20 should provide a good ARM (cache enabled)
+	 * performance and still allow good utilization by the VPSS or other
+	 * modules.
+	 */
+	REG(VBPR) = 0x20;
+}