1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
|
menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)"
config GSC
bool "VSC/GSC/HSC bus support"
default y
help
The VSC, GSC and HSC busses were used from the earliest 700-series
workstations up to and including the C360/J2240 workstations. They
were also used in servers from the E-class to the K-class. They
are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards.
If in doubt, say "Y".
config HPPB
bool "HP-PB bus support"
depends on GSC
help
The HP-PB bus was used in the Nova class and K-class servers.
If in doubt, say "Y"
config IOMMU_CCIO
bool "U2/Uturn I/O MMU"
depends on GSC
help
Say Y here to enable DMA management routines for the first
generation of PA-RISC cache-coherent machines. Programs the
U2/Uturn chip in "Virtual Mode" and use the I/O MMU.
config GSC_LASI
bool "Lasi I/O support"
depends on GSC
help
Say Y here to support the Lasi multifunction chip found in
many PA-RISC workstations & servers. It includes interfaces
for a parallel port, serial port, NCR 53c710 SCSI, Apricot
Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony
and floppy. Note that you must still enable all the individual
drivers for these chips.
config GSC_WAX
bool "Wax I/O support"
depends on GSC
help
Say Y here to support the Wax multifunction chip found in some
older systems, including B/C/D/R class and 715/64, 715/80 and
715/100. Wax includes an EISA adapter, a serial port (not always
used), a HIL interface chip and is also known to be used as the
GSC bridge for an X.25 GSC card.
config EISA
bool "EISA support"
depends on GSC
help
Say Y here if you have an EISA bus in your machine. This code
supports both the Mongoose & Wax EISA adapters. It is sadly
incomplete and lacks support for card-to-host DMA.
source "drivers/eisa/Kconfig"
config ISA
bool "ISA support"
depends on EISA
help
If you want to plug an ISA card into your EISA bus, say Y here.
Most people should say N.
config PCI
bool "PCI support"
help
All recent HP machines have PCI slots, and you should say Y here
if you have a recent machine. If you are convinced you do not have
PCI slots in your machine (eg a 712), then you may say "N" here.
Beware that some GSC cards have a Dino onboard and PCI inside them,
so it may be safest to say "Y" anyway.
source "drivers/pci/Kconfig"
config GSC_DINO
bool "GSCtoPCI/Dino PCI support"
depends on PCI && GSC
help
Say Y here to support the Dino & Cujo GSC to PCI bridges found in
machines from the B132 to the C360, the J2240 and the A180. Some
GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on
the card, and you also need to say Y here if you have such a card.
Note that Dino also supplies one of the serial ports on certain
machines. If in doubt, say Y.
config PCI_LBA
bool "LBA/Elroy PCI support"
depends on PCI
help
Say Y here to support the Elroy PCI Lower Bus Adapter. This is
present on B, C, J, L and N-class machines with 4-digit model
numbers and the A400/A500.
config IOSAPIC
bool
depends on PCI_LBA
default PCI_LBA
config IOMMU_SBA
bool
depends on PCI_LBA
default PCI_LBA
config IOMMU_HELPER
bool
depends on IOMMU_SBA || IOMMU_CCIO
default y
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
endmenu
menu "PA-RISC specific drivers"
config SUPERIO
bool "SuperIO (SuckyIO) support"
depends on PCI_LBA
default y
help
Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and
J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and
Serial port on those machines.
config CHASSIS_LCD_LED
bool "Chassis LCD and LED support"
default y
help
Say Y here if you want to enable support for the Heartbeat,
Disk/Network activities LEDs on some PA-RISC machines,
or support for the LCD that can be found on recent material.
This has nothing to do with LED State support for A and E class.
If unsure, say Y.
config PDC_CHASSIS
bool "PDC chassis state codes support"
default y
help
Say Y here if you want to enable support for Chassis codes.
That includes support for LED State front panel as found on E
class, and support for the GSP Virtual Front Panel (LED State and
message logging) as found on high end servers such as A, L and
N-class.
This driver will also display progress messages on LCD display,
such as "INI", "RUN" and "FLT", and might thus clobber messages
shown by the LED/LCD driver.
This driver updates the state panel (LED and/or LCD) upon system
state change (eg: boot, shutdown or panic).
If unsure, say Y.
config PDC_CHASSIS_WARN
bool "PDC chassis warnings support"
depends on PROC_FS
default y
help
Say Y here if you want to enable support for Chassis warnings.
This will add a proc entry '/proc/chassis' giving some information
about the overall health state of the system.
This includes NVRAM battery level, overtemp or failures such as
fans or power units.
If unsure, say Y.
config PDC_STABLE
tristate "PDC Stable Storage support"
depends on SYSFS
default y
help
Say Y here if you want to enable support for accessing Stable Storage
variables (PDC non volatile variables such as Primary Boot Path,
Console Path, Autoboot, Autosearch, etc) through SysFS.
If unsure, say Y.
To compile this driver as a module, choose M here.
The module will be called pdc_stable.
endmenu
|
