summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* NFC: st-nci: Increase delay between 2 secure element activationsChristophe Ricard2015-10-271-1/+1
| | | | | | | | After internal discussion, it appears this timing should be increased to 20 ms for interoperability reason. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Add ese-present/uicc-present dts propertiesChristophe Ricard2015-10-2710-46/+122
| | | | | | | | | | | | | | | | | | | | In order to align with st21nfca, dts configuration properties ese_present and uicc_present are made available in st-nci driver. So far, in early development firmware, because nci_nfcee_mode_set(DISABLE) was not supported we had to try to enable it during the secure element discovery phase. After several trials on commercial and qualified firmware it appears that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are properly supported. Such feature also help us to eventually save some time (~5ms) when only one secure element is connected. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: netlink: Add missing NFC_ATTR commentsChristophe Ricard2015-10-271-0/+2
| | | | | | | NFC_CMD_ACTIVATE_TARGET and NFC_ATTR_SE_PARAMS comments are missing. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Add error messages when an unexpected HCI event occursChristophe Ricard2015-10-271-0/+6
| | | | | | | | | Potentially an unexpected HCI event may occur because of a firmware bug. It could be transparent for the user but we need to at least log it. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Add support for proprietary commandsChristophe Ricard2015-10-276-10/+619
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for proprietary commands useful mainly for factory testings. Here is a list: - FACTORY_MODE: Allow to set the driver into a mode where no secure element are activated. It does not consider any NFC_ATTR_VENDOR_DATA. - HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes command. It does not consider any NFC_ATTR_VENDOR_DATA. - HCI_DM_PUT_DATA: Allow to configure specific CLF registry like for example RF trimmings or low level drivers configurations (I2C, SPI, SWP). - HCI_DM_UPDATE_AID: Allow to configure an AID routing into the CLF routing table following RF technology, CLF mode or protocol. - HCI_DM_GET_INFO: Allow to retrieve CLF information. - HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as low level drivers configurations or RF trimmings. - HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF. A complete packet can be more than 8KB. - HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF configuration changes without CLF power off. - HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example the white list). - HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF technology. When using this command to anti-collision is done. - HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF connectivity. - HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied on the CLF antenna. A value between 0 and 0x0f is returned. 0 is maximum. - HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode. It is a specific CLF command as there is no GPIO for this. - HCI_DM_FWUPD_END: Allow to complete firmware update. - HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied on the CLF antenna to a reference value. - MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data received during a NCI_CORE_INIT_CMD. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Fix st21nfca_gates offsetChristophe Ricard2015-10-261-3/+4
| | | | | | | | | | | It is useless to start from index 0 when looking for a gate because only dynamic pipes are retrieved with ST21NFCA_DM_GETINFO(ST21NFCA_DM_GETINFO_PIPE_LIST). The first dynamic pipe is present at index 3. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Fix st_nci_gates offsetChristophe Ricard2015-10-261-1/+1
| | | | | | | | | | | It is useless to start from index 0 when looking for a gate because only dynamic pipes are retrieved with ST_NCI_DM_GETINFO(ST_NCI_DM_GETINFO_PIPE_LIST). The first dynamic pipe is present at index 3. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Add support for NCI_HCI_IDENTITY_MGMT_GATEChristophe Ricard2015-10-262-0/+4
| | | | | | | | NCI_HCI_IDENTITY_MGMT_GATE might be useful to get information about hardware or firmware version. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: initialize gate_count in st_nci_hci_network_initChristophe Ricard2015-10-261-0/+1
| | | | | | | | | When initializing ndev->hci_dev->init_data, only gates field was set. gate_count needs to be initialized as well. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Keep st21nfca_gates unchanged in load_sessionChristophe Ricard2015-10-261-6/+6
| | | | | | | | | | | | | We need to keep initial st_nci_gates values in order for nfc_hci_dev_connect_gates to create and open pipe when necessary. For example after a firmware update CLF pipes are cleared. Changing pipe values in st21nfca_gates was causing nfc_hci_dev_connect_gates not using accurate pipes value. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Keep st_nci_gates unchanged in load_sessionChristophe Ricard2015-10-261-4/+4
| | | | | | | | | | | | | We need to keep initial st_nci_gates values in order for nci_hci_dev_connect_gates to create and open pipe when necessary. For example after a firmware update CLF pipes are cleared. Changing pipe values in st_nci_gates was causing nci_hci_dev_connect_gates not using accurate pipes value. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Open NFC_HCI_LINK_MGMT_PIPEChristophe Ricard2015-10-261-14/+5
| | | | | | | | NFC_HCI_LINK_MGMT_PIPE was never opened in nfc_hci_load_session. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Open NCI_HCI_LINK_MGMT_PIPEChristophe Ricard2015-10-261-0/+8
| | | | | | | NCI_HCI_LINK_MGMT_PIPE was never opened in st_nci_hci_load_session. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Remove HCI gates initialization in load_sessionChristophe Ricard2015-10-261-1/+0
| | | | | | | | hdev->init_data.gates is already initialized in st21nfca_hci_probe. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Remove HCI init_data.gates initialization in load_sessionChristophe Ricard2015-10-261-3/+0
| | | | | | | | | ndev->hci_dev->init_data.gates is already initialized in st_nci_hci_network. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Create pipe on specific gate in nci_hci_connect_gateChristophe Ricard2015-10-261-1/+55
| | | | | | | | | | | | | Some gates might need to have their pipes explicitly created. Add a call to nci_hci_create_pipe in nci_hci_connect_gate for every gate that is different than NCI_HCI_LINK_MGMT_GATE or NCI_HCI_ADMIN_GATE. In case of an error when opening a pipe, like in hci layer, delete the pipe if it was created. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Call nci_hci_clear_all_pipes at HCI initial activation.Christophe Ricard2015-10-261-0/+4
| | | | | | | | When session_id is filled to 0xff, the pipe configuration is probably incorrect and needs to be cleared. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: add nci_hci_clear_all_pipes functionsChristophe Ricard2015-10-262-0/+16
| | | | | | | | nci_hci_clear_all_pipes might be use full in some cases for example after a firmware update. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: extract pipe value using NCI_HCP_MSG_GET_PIPEChristophe Ricard2015-10-261-2/+2
| | | | | | | | | When receiving data in nci_hci_msg_rx_work, extract pipe value using NCI_HCP_MSG_GET_PIPE macro. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Fix improper management of HCI return codeChristophe Ricard2015-10-261-17/+49
| | | | | | | | | | | | | | When sending HCI data over NCI, HCI return code is part of the NCI data. In order to get correctly the HCI return code, we assume the NCI communication is successful and extract the return code for the nci_hci functions return code. This is done because nci_to_errno does not match hci return code value. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Fix incorrect data chaining when sending dataChristophe Ricard2015-10-261-7/+13
| | | | | | | | | | | When sending HCI data over NCI, cmd information should be present only on the first packet. Each packet shall be specifically allocated and sent to the NCI layer. Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Fix incorrect spi buffer sizeChristophe Ricard2015-10-261-1/+3
| | | | | | | | | | When sending data over SPI, the maximum expected length is the maximum nci packet payload + data header size + the frame head room (1 for the ndlc header) + the frame trail room (0). Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Align st21nfca driver with other nfc driverChristophe Ricard2015-10-267-130/+80
| | | | | | | | | Align st21nfca driver with or nfc driver: - Remove st21nfca_ prefix - Merge st21nfca_se.h, st21nfca_dep.h in st21nfca.h Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: include st-nci.h instead of ndlc.hChristophe Ricard2015-10-263-3/+2
| | | | | | | st-nci.h already include ndlc.h. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Align st-nci driver with other nfc driverChristophe Ricard2015-10-264-64/+39
| | | | | | | | | Align st-nci driver with other NFC drivers: - Remove st-nci_ prefix - Merge se.h in st-nci.h Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: Add Intel Fields Peak NFC solution driverRobert Dolca2015-10-257-0/+1277
| | | | | | | | | | | | | | | | | | | | | | | | Fields Peak complies with the ISO/IEC 14443A/B, 15693, 18092, and JIS X 6319-4. It is an NCI based controller. RF Protocols supported: - NFC Forum Type 1 Tags (Jewel, Topaz) - NFC Forum Type 2 Tags (Mifare UL) - NFC Forum Type 3 Tags (FeliCa) - NFC Forum Type 4A (ISO/IEC 14443 A-4 106kbps to 848kbps) - NFC Forum Type 4B (ISO/IEC 14443 B-4 106kbps to 848kbps) - NFCIP in passive and active modes (ISO/IEC 18092 106kbps to 424kbps) - B’ (based on ISO/IEC 14443 B-2) - iCLASS (based on ISO/IEC 15693-2) - Vicinity cards (ISO/IEC 15693-3) - Kovio tags (NFC Forum Type 2) The device can be enumerated using ACPI using the id INT339A. The 1st GPIO is the IRQ and the 2nd is the RESET pin. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: add nci_get_conn_info_by_id functionRobert Dolca2015-10-252-0/+14
| | | | | | | | | This functin takes as a parameter a pointer to the nci_dev struct and the first byte from the values of the first domain specific parameter that was used for the connection creation. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: fix possible crash in nci_core_conn_createRobert Dolca2015-10-251-1/+8
| | | | | | | | | If the number of destination speific parameters supplied is 0 the call will fail. If the first destination specific parameter does not have a value, curr_id will be set to 0. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: rename nci_prop_ops to nci_driver_opsRobert Dolca2015-10-255-15/+15
| | | | | | | | | Initially it was used to create hooks in the driver for proprietary operations. Currently it is being used for hooks for both proprietary and generic operations. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Allow the driver to set handler for core nci opsRobert Dolca2015-10-254-23/+63
| | | | | | | | | | | | | | | | | The driver may be required to act when some responses or notifications arrive. For example the NCI core does not have a handler for NCI_OP_CORE_GET_CONFIG_RSP. The NFCC can send a config response that has to be read by the driver and the packet may contain vendor specific data. The Fields Peak driver needs to take certain actions when a reset notification arrives (packet also not handled by the nfc core). The driver handlers do not interfere with the core and they are called after the core processes the packet. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Introduce nci_core_cmdRobert Dolca2015-10-252-5/+20
| | | | | | | | This allows sending core commands from the driver. The driver should be able to send NCI core commands like CORE_GET_CONFIG_CMD. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Do not call post_setup when setup failsRobert Dolca2015-10-251-2/+1
| | | | | | | | | The driver should know that it can continue with post setup where setup left off. Being able to execute post_setup when setup fails may force the developer to keep this state in the driver. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Introduce new core opcodesRobert Dolca2015-10-251-0/+7
| | | | | | | | Add NCI_OP_CORE_GET_CONFIG_CMD, NCI_OP_CORE_GET_CONFIG_RSP and NCI_OP_CORE_RESET_NTF. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Add function to get max packet size for connRobert Dolca2015-10-252-0/+13
| | | | | | | | | FDP driver needs to send the firmware as regular packets (not fragmented). The driver should have a way to get the max packet size for a given connection. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Export nci data send APIRobert Dolca2015-10-251-0/+1
| | | | | | | For the firmware update the driver may use nci_send_data. Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st-nci: Rename st-nci_se.cSamuel Ortiz2015-10-255-4/+4
| | | | | | Rename it to se.c to keep the driver files namespace consistent. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: delete null dereferenceJulia Lawall2015-10-191-4/+2
| | | | | | | | | | | The exit label performs device_unlock(&dev->dev);, which will fail when dev is NULL, and nfc_put_device(dev);, which is not useful when dev is NULL, so just exit the function immediately. Problem found using scripts/coccinelle/null/deref_null.cocci Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nfcwilink: Drop a useless static qualifierChristophe JAILLET2015-10-191-1/+1
| | | | | | | | | There is no need to have the 'struct nfcwilink *drv' variable static in the probe function. It only wastes a few bytes of memory. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nxp-nci: constify nxp_nci_phy_ops structureJulia Lawall2015-10-193-4/+6
| | | | | | | | | | | The only instance of a nxp_nci_phy_ops structure is never modified. Thus the declaration of the structure and all references to the structure type can be made const. Done with the help of Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nfcmrvl: Auto-select core moduleJean Delvare2015-10-191-7/+5
| | | | | | | | | | | | | | | As I understand it, the core nfcmrvl module is useless without either the USB or the UART access module. So hide NFC_MRVL and select it automatically if either NFC_MRVL_USB or NFC_MRVL_UART is selected. This avoids presenting NFC_MRVL when neither NFC_MRVL_USB nor NFC_MRVL_UART can be selected. Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org> Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: microread: Auto-select core moduleJean Delvare2015-10-191-11/+7
| | | | | | | | | | | | | | | | As I understand it, the core nfc_microread module is useless without either the I2C or the MEI access module. So hide NFC_MICROREAD and select it automatically if either NFC_MICROREAD_I2C or NFC_MICROREAD_MEI is selected. This avoids presenting NFC_MICROREAD when neither NFC_MICROREAD_I2C nor NFC_MICROREAD_MEI can be selected. Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org> Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: pn544: Auto-select core moduleJean Delvare2015-10-191-11/+7
| | | | | | | | | | | | | | | | As I understand it, the core nfc_pn544 module is useless without either the I2C or the MEI access module. So hide NFC_PN544 and select it automatically if either NFC_PN544_I2C or NFC_PN544_MEI is selected. This avoids presenting NFC_PN544 when neither NFC_PN544_I2C nor NFC_PN544_MEI can be selected. Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org> Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add OF match tableJavier Martinez Canillas2015-10-191-0/+7
| | | | | | | | | | The Documentation/devicetree/bindings/net/nfc/trf7970a.txt DT binding doc lists "ti,trf7970a" as a compatible string but the corresponding driver does not have an OF match table. Add the table to the driver so the SPI core can do an OF style match. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* nfc: s3fwrn5: i2c: Use devm_request_threaded_irq to avoid irq leakAxel Lin2015-10-071-1/+1
| | | | | | Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* nfc: s3fwrn5: Make NFC_S3FWRN5 select CRYPTOAxel Lin2015-10-071-0/+1
| | | | | | | | | | | | | Make NFC_S3FWRN5 select CRYPTO to fix below build errors: ERROR: "crypto_destroy_tfm" [drivers/nfc/s3fwrn5/s3fwrn5.ko] undefined! ERROR: "crypto_alloc_base" [drivers/nfc/s3fwrn5/s3fwrn5.ko] undefined! scripts/Makefile.modpost:91: recipe for target '__modpost' failed make[1]: *** [__modpost] Error 1 Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: s3fwrn5: Remove superfluous cflagsValentin Rothberg2015-10-071-2/+0
| | | | | | | | | NFC_DEBUG is not defined in Kconfig and since DEBUG is not used anywhere in this directory, we can safely remove this line. Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com> Acked-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: nci: Use __nci_request for exported routinesSamuel Ortiz2015-10-031-5/+6
| | | | | | | | | | | | Since we do not know in which context drivers will call these routines, they should use the unlocked version of nci_request, i.e. __nci_request. It is up to drivers to know/decide if they need to take the req_lock mutex before calling those routines. When being called from the NCI setup routine there is no need to do so as ops->setup is called under req_lock. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-10-02240-1379/+2429
|\ | | | | | | | | | | | | | | | | Conflicts: net/dsa/slave.c net/dsa/slave.c simply had overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmcLinus Torvalds2015-10-024-62/+67
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull MMC fixes from Ulf Hansson: "Here are some mmc fixes intended for v4.3 rc4: MMC core: - Allow users of mmc_of_parse() to succeed when CONFIG_GPIOLIB is unset - Prevent infinite loop of re-tuning for CRC-errors for CMD19 and CMD21 MMC host: - pxamci: Fix issues with card detect - sunxi: Fix clk-delay settings" * tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc: mmc: core: fix dead loop of mmc_retune mmc: pxamci: fix card detect with slot-gpio API mmc: sunxi: Fix clk-delay settings mmc: core: Don't return an error for CD/WP GPIOs when GPIOLIB is unset
| | * mmc: core: fix dead loop of mmc_retuneChaotian Jing2015-09-301-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21 to do tune, assume there were 10 clock phase need to try, phase 0 to phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so the last CMD19/CMD21 will get CRC error, host->need_retune was set and cause mmc_retune was called, then dead loop of mmc_retune Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
OpenPOWER on IntegriCloud