diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/defines.h | 6 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/hw.h | 4 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/mac.c | 125 |
3 files changed, 132 insertions, 3 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h index 02a12b69555f..20735327a7a0 100644 --- a/drivers/net/ethernet/intel/e1000e/defines.h +++ b/drivers/net/ethernet/intel/e1000e/defines.h @@ -241,9 +241,9 @@ #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ -/* Bit definitions for the Management Data IO (MDIO) and Management Data - * Clock (MDC) pins in the Device Control Register. - */ +#define E1000_PCS_LCTL_FORCE_FCTRL 0x80 + +#define E1000_PCS_LSTS_AN_COMPLETE 0x10000 /* Device Status */ #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h index cf217777586c..06239fe47db1 100644 --- a/drivers/net/ethernet/intel/e1000e/hw.h +++ b/drivers/net/ethernet/intel/e1000e/hw.h @@ -191,6 +191,10 @@ enum e1e_registers { E1000_ICTXQMTC = 0x0411C, /* Irq Cause Tx Queue MinThreshold Count */ E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */ E1000_ICRXOC = 0x04124, /* Irq Cause Receiver Overrun Count */ + E1000_PCS_LCTL = 0x04208, /* PCS Link Control - RW */ + E1000_PCS_LSTAT = 0x0420C, /* PCS Link Status - RO */ + E1000_PCS_ANADV = 0x04218, /* AN advertisement - RW */ + E1000_PCS_LPAB = 0x0421C, /* Link Partner Ability - RW */ E1000_RXCSUM = 0x05000, /* Rx Checksum Control - RW */ E1000_RFCTL = 0x05008, /* Receive Filter Control */ E1000_MTA = 0x05200, /* Multicast Table Array - RW Array */ diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c index 54d9dafaf126..0fa4c0656e09 100644 --- a/drivers/net/ethernet/intel/e1000e/mac.c +++ b/drivers/net/ethernet/intel/e1000e/mac.c @@ -1021,6 +1021,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; s32 ret_val = 0; + u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg; u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; u16 speed, duplex; @@ -1185,6 +1186,130 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) } } + /* Check for the case where we have SerDes media and auto-neg is + * enabled. In this case, we need to check and see if Auto-Neg + * has completed, and if so, how the PHY and link partner has + * flow control configured. + */ + if ((hw->phy.media_type == e1000_media_type_internal_serdes) && + mac->autoneg) { + /* Read the PCS_LSTS and check to see if AutoNeg + * has completed. + */ + pcs_status_reg = er32(PCS_LSTAT); + + if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) { + e_dbg("PCS Auto Neg has not completed.\n"); + return ret_val; + } + + /* The AutoNeg process has completed, so we now need to + * read both the Auto Negotiation Advertisement + * Register (PCS_ANADV) and the Auto_Negotiation Base + * Page Ability Register (PCS_LPAB) to determine how + * flow control was negotiated. + */ + pcs_adv_reg = er32(PCS_ANADV); + pcs_lp_ability_reg = er32(PCS_LPAB); + + /* Two bits in the Auto Negotiation Advertisement Register + * (PCS_ANADV) and two bits in the Auto Negotiation Base + * Page Ability Register (PCS_LPAB) determine flow control + * for both the PHY and the link partner. The following + * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, + * 1999, describes these PAUSE resolution bits and how flow + * control is determined based upon these settings. + * NOTE: DC = Don't Care + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution + *-------|---------|-------|---------|-------------------- + * 0 | 0 | DC | DC | e1000_fc_none + * 0 | 1 | 0 | DC | e1000_fc_none + * 0 | 1 | 1 | 0 | e1000_fc_none + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + * 1 | 0 | 0 | DC | e1000_fc_none + * 1 | DC | 1 | DC | e1000_fc_full + * 1 | 1 | 0 | 0 | e1000_fc_none + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + * + * Are both PAUSE bits set to 1? If so, this implies + * Symmetric Flow Control is enabled at both ends. The + * ASM_DIR bits are irrelevant per the spec. + * + * For Symmetric Flow Control: + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | DC | 1 | DC | e1000_fc_full + * + */ + if ((pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) { + /* Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise Rx + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == e1000_fc_full) { + hw->fc.current_mode = e1000_fc_full; + e_dbg("Flow Control = FULL.\n"); + } else { + hw->fc.current_mode = e1000_fc_rx_pause; + e_dbg("Flow Control = Rx PAUSE frames only.\n"); + } + } + /* For receiving PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + */ + else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_adv_reg & E1000_TXCW_ASM_DIR) && + (pcs_lp_ability_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_tx_pause; + e_dbg("Flow Control = Tx PAUSE frames only.\n"); + } + /* For transmitting PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + */ + else if ((pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_adv_reg & E1000_TXCW_ASM_DIR) && + !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_rx_pause; + e_dbg("Flow Control = Rx PAUSE frames only.\n"); + } else { + /* Per the IEEE spec, at this point flow control + * should be disabled. + */ + hw->fc.current_mode = e1000_fc_none; + e_dbg("Flow Control = NONE.\n"); + } + + /* Now we call a subroutine to actually force the MAC + * controller to use the correct flow control settings. + */ + pcs_ctrl_reg = er32(PCS_LCTL); + pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL; + ew32(PCS_LCTL, pcs_ctrl_reg); + + ret_val = e1000e_force_mac_fc(hw); + if (ret_val) { + e_dbg("Error forcing flow control settings\n"); + return ret_val; + } + } + return 0; } |
