diff options
Diffstat (limited to 'drivers/lguest/lguest.c')
| -rw-r--r-- | drivers/lguest/lguest.c | 32 |
1 files changed, 11 insertions, 21 deletions
diff --git a/drivers/lguest/lguest.c b/drivers/lguest/lguest.c index ca9b844f37c2..c302629e0895 100644 --- a/drivers/lguest/lguest.c +++ b/drivers/lguest/lguest.c @@ -97,29 +97,17 @@ static cycle_t clock_base; * them as a batch when lazy_mode is eventually turned off. Because hypercalls * are reasonably expensive, batching them up makes sense. For example, a * large mmap might update dozens of page table entries: that code calls - * lguest_lazy_mode(PARAVIRT_LAZY_MMU), does the dozen updates, then calls - * lguest_lazy_mode(PARAVIRT_LAZY_NONE). + * paravirt_enter_lazy_mmu(), does the dozen updates, then calls + * lguest_leave_lazy_mode(). * * So, when we're in lazy mode, we call async_hypercall() to store the call for * future processing. When lazy mode is turned off we issue a hypercall to * flush the stored calls. - * - * There's also a hack where "mode" is set to "PARAVIRT_LAZY_FLUSH" which - * indicates we're to flush any outstanding calls immediately. This is used - * when an interrupt handler does a kmap_atomic(): the page table changes must - * happen immediately even if we're in the middle of a batch. Usually we're - * not, though, so there's nothing to do. */ -static enum paravirt_lazy_mode lazy_mode; /* Note: not SMP-safe! */ -static void lguest_lazy_mode(enum paravirt_lazy_mode mode) + */ +static void lguest_leave_lazy_mode(void) { - if (mode == PARAVIRT_LAZY_FLUSH) { - if (unlikely(lazy_mode != PARAVIRT_LAZY_NONE)) - hcall(LHCALL_FLUSH_ASYNC, 0, 0, 0); - } else { - lazy_mode = mode; - if (mode == PARAVIRT_LAZY_NONE) - hcall(LHCALL_FLUSH_ASYNC, 0, 0, 0); - } + paravirt_leave_lazy(paravirt_get_lazy_mode()); + hcall(LHCALL_FLUSH_ASYNC, 0, 0, 0); } static void lazy_hcall(unsigned long call, @@ -127,7 +115,7 @@ static void lazy_hcall(unsigned long call, unsigned long arg2, unsigned long arg3) { - if (lazy_mode == PARAVIRT_LAZY_NONE) + if (paravirt_get_lazy_mode() == PARAVIRT_LAZY_NONE) hcall(call, arg1, arg2, arg3); else async_hcall(call, arg1, arg2, arg3); @@ -1011,6 +999,8 @@ __init void lguest_init(void *boot) pv_cpu_ops.write_gdt_entry = lguest_write_gdt_entry; pv_cpu_ops.write_idt_entry = lguest_write_idt_entry; pv_cpu_ops.wbinvd = lguest_wbinvd; + pv_cpu_ops.lazy_mode.enter = paravirt_enter_lazy_cpu; + pv_cpu_ops.lazy_mode.leave = lguest_leave_lazy_mode; /* pagetable management */ pv_mmu_ops.write_cr3 = lguest_write_cr3; @@ -1022,6 +1012,8 @@ __init void lguest_init(void *boot) pv_mmu_ops.set_pmd = lguest_set_pmd; pv_mmu_ops.read_cr2 = lguest_read_cr2; pv_mmu_ops.read_cr3 = lguest_read_cr3; + pv_mmu_ops.lazy_mode.enter = paravirt_enter_lazy_mmu; + pv_mmu_ops.lazy_mode.leave = lguest_leave_lazy_mode; #ifdef CONFIG_X86_LOCAL_APIC /* apic read/write intercepts */ @@ -1034,8 +1026,6 @@ __init void lguest_init(void *boot) pv_time_ops.get_wallclock = lguest_get_wallclock; pv_time_ops.time_init = lguest_time_init; - pv_misc_ops.set_lazy_mode = lguest_lazy_mode; - /* Now is a good time to look at the implementations of these functions * before returning to the rest of lguest_init(). */ |
