diff options
Diffstat (limited to 'arch/arm/mach-omap2/opp2xxx.h')
| -rw-r--r-- | arch/arm/mach-omap2/opp2xxx.h | 424 |
1 files changed, 424 insertions, 0 deletions
diff --git a/arch/arm/mach-omap2/opp2xxx.h b/arch/arm/mach-omap2/opp2xxx.h new file mode 100644 index 000000000000..ed6df04e2f29 --- /dev/null +++ b/arch/arm/mach-omap2/opp2xxx.h @@ -0,0 +1,424 @@ +/* + * opp2xxx.h - macros for old-style OMAP2xxx "OPP" definitions + * + * Copyright (C) 2005-2009 Texas Instruments, Inc. + * Copyright (C) 2004-2009 Nokia Corporation + * + * Richard Woodruff <r-woodruff2@ti.com> + * + * The OMAP2 processor can be run at several discrete 'PRCM configurations'. + * These configurations are characterized by voltage and speed for clocks. + * The device is only validated for certain combinations. One way to express + * these combinations is via the 'ratio's' which the clocks operate with + * respect to each other. These ratio sets are for a given voltage/DPLL + * setting. All configurations can be described by a DPLL setting and a ratio + * There are 3 ratio sets for the 2430 and X ratio sets for 2420. + * + * 2430 differs from 2420 in that there are no more phase synchronizers used. + * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs + * 2430 (iva2.1, NOdsp, mdm) + * + * XXX Missing voltage data. + * + * THe format described in this file is deprecated. Once a reasonable + * OPP API exists, the data in this file should be converted to use it. + * + * This is technically part of the OMAP2xxx clock code. + */ + +#ifndef __ARCH_ARM_MACH_OMAP2_OPP2XXX_H +#define __ARCH_ARM_MACH_OMAP2_OPP2XXX_H + +/** + * struct prcm_config - define clock rates on a per-OPP basis (24xx) + * + * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated. + * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,CM_CLKSEL_DSP + * CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL CM_CLKSEL2_PLL, CM_CLKSEL_MDM + * + * This is deprecated. As soon as we have a decent OPP API, we should + * move all this stuff to it. + */ +struct prcm_config { + unsigned long xtal_speed; /* crystal rate */ + unsigned long dpll_speed; /* dpll: out*xtal*M/(N-1)table_recalc */ + unsigned long mpu_speed; /* speed of MPU */ + unsigned long cm_clksel_mpu; /* mpu divider */ + unsigned long cm_clksel_dsp; /* dsp+iva1 div(2420), iva2.1(2430) */ + unsigned long cm_clksel_gfx; /* gfx dividers */ + unsigned long cm_clksel1_core; /* major subsystem dividers */ + unsigned long cm_clksel1_pll; /* m,n */ + unsigned long cm_clksel2_pll; /* dpllx1 or x2 out */ + unsigned long cm_clksel_mdm; /* modem dividers 2430 only */ + unsigned long base_sdrc_rfr; /* base refresh timing for a set */ + unsigned char flags; +}; + + +/* Core fields for cm_clksel, not ratio governed */ +#define RX_CLKSEL_DSS1 (0x10 << 8) +#define RX_CLKSEL_DSS2 (0x0 << 13) +#define RX_CLKSEL_SSI (0x5 << 20) + +/*------------------------------------------------------------------------- + * Voltage/DPLL ratios + *-------------------------------------------------------------------------*/ + +/* 2430 Ratio's, 2430-Ratio Config 1 */ +#define R1_CLKSEL_L3 (4 << 0) +#define R1_CLKSEL_L4 (2 << 5) +#define R1_CLKSEL_USB (4 << 25) +#define R1_CM_CLKSEL1_CORE_VAL (R1_CLKSEL_USB | RX_CLKSEL_SSI | \ + RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ + R1_CLKSEL_L4 | R1_CLKSEL_L3) +#define R1_CLKSEL_MPU (2 << 0) +#define R1_CM_CLKSEL_MPU_VAL R1_CLKSEL_MPU +#define R1_CLKSEL_DSP (2 << 0) +#define R1_CLKSEL_DSP_IF (2 << 5) +#define R1_CM_CLKSEL_DSP_VAL (R1_CLKSEL_DSP | R1_CLKSEL_DSP_IF) +#define R1_CLKSEL_GFX (2 << 0) +#define R1_CM_CLKSEL_GFX_VAL R1_CLKSEL_GFX +#define R1_CLKSEL_MDM (4 << 0) +#define R1_CM_CLKSEL_MDM_VAL R1_CLKSEL_MDM + +/* 2430-Ratio Config 2 */ +#define R2_CLKSEL_L3 (6 << 0) +#define R2_CLKSEL_L4 (2 << 5) +#define R2_CLKSEL_USB (2 << 25) +#define R2_CM_CLKSEL1_CORE_VAL (R2_CLKSEL_USB | RX_CLKSEL_SSI | \ + RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ + R2_CLKSEL_L4 | R2_CLKSEL_L3) +#define R2_CLKSEL_MPU (2 << 0) +#define R2_CM_CLKSEL_MPU_VAL R2_CLKSEL_MPU +#define R2_CLKSEL_DSP (2 << 0) +#define R2_CLKSEL_DSP_IF (3 << 5) +#define R2_CM_CLKSEL_DSP_VAL (R2_CLKSEL_DSP | R2_CLKSEL_DSP_IF) +#define R2_CLKSEL_GFX (2 << 0) +#define R2_CM_CLKSEL_GFX_VAL R2_CLKSEL_GFX +#define R2_CLKSEL_MDM (6 << 0) +#define R2_CM_CLKSEL_MDM_VAL R2_CLKSEL_MDM + +/* 2430-Ratio Bootm (BYPASS) */ +#define RB_CLKSEL_L3 (1 << 0) +#define RB_CLKSEL_L4 (1 << 5) +#define RB_CLKSEL_USB (1 << 25) +#define RB_CM_CLKSEL1_CORE_VAL (RB_CLKSEL_USB | RX_CLKSEL_SSI | \ + RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ + RB_CLKSEL_L4 | RB_CLKSEL_L3) +#define RB_CLKSEL_MPU (1 << 0) +#define RB_CM_CLKSEL_MPU_VAL RB_CLKSEL_MPU +#define RB_CLKSEL_DSP (1 << 0) +#define RB_CLKSEL_DSP_IF (1 << 5) +#define RB_CM_CLKSEL_DSP_VAL (RB_CLKSEL_DSP | RB_CLKSEL_DSP_IF) +#define RB_CLKSEL_GFX (1 << 0) +#define RB_CM_CLKSEL_GFX_VAL RB_CLKSEL_GFX +#define RB_CLKSEL_MDM (1 << 0) +#define RB_CM_CLKSEL_MDM_VAL RB_CLKSEL_MDM + +/* 2420 Ratio Equivalents */ +#define RXX_CLKSEL_VLYNQ (0x12 << 15) +#define RXX_CLKSEL_SSI (0x8 << 20) + +/* 2420-PRCM III 532MHz core */ +#define RIII_CLKSEL_L3 (4 << 0) /* 133MHz */ +#define RIII_CLKSEL_L4 (2 << 5) /* 66.5MHz */ +#define RIII_CLKSEL_USB (4 << 25) /* 33.25MHz */ +#define RIII_CM_CLKSEL1_CORE_VAL (RIII_CLKSEL_USB | RXX_CLKSEL_SSI | \ + RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \ + RX_CLKSEL_DSS1 | RIII_CLKSEL_L4 | \ + RIII_CLKSEL_L3) +#define RIII_CLKSEL_MPU (2 << 0) /* 266MHz */ +#define RIII_CM_CLKSEL_MPU_VAL RIII_CLKSEL_MPU +#define RIII_CLKSEL_DSP (3 << 0) /* c5x - 177.3MHz */ +#define RIII_CLKSEL_DSP_IF (2 << 5) /* c5x - 88.67MHz */ +#define RIII_SYNC_DSP (1 << 7) /* Enable sync */ +#define RIII_CLKSEL_IVA (6 << 8) /* iva1 - 88.67MHz */ +#define RIII_SYNC_IVA (1 << 13) /* Enable sync */ +#define RIII_CM_CLKSEL_DSP_VAL (RIII_SYNC_IVA | RIII_CLKSEL_IVA | \ + RIII_SYNC_DSP | RIII_CLKSEL_DSP_IF | \ + RIII_CLKSEL_DSP) +#define RIII_CLKSEL_GFX (2 << 0) /* 66.5MHz */ +#define RIII_CM_CLKSEL_GFX_VAL RIII_CLKSEL_GFX + +/* 2420-PRCM II 600MHz core */ +#define RII_CLKSEL_L3 (6 << 0) /* 100MHz */ +#define RII_CLKSEL_L4 (2 << 5) /* 50MHz */ +#define RII_CLKSEL_USB (2 << 25) /* 50MHz */ +#define RII_CM_CLKSEL1_CORE_VAL (RII_CLKSEL_USB | RXX_CLKSEL_SSI | \ + RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \ + RX_CLKSEL_DSS1 | RII_CLKSEL_L4 | \ + RII_CLKSEL_L3) +#define RII_CLKSEL_MPU (2 << 0) /* 300MHz */ +#define RII_CM_CLKSEL_MPU_VAL RII_CLKSEL_MPU +#define RII_CLKSEL_DSP (3 << 0) /* c5x - 200MHz */ +#define RII_CLKSEL_DSP_IF (2 << 5) /* c5x - 100MHz */ +#define RII_SYNC_DSP (0 << 7) /* Bypass sync */ +#define RII_CLKSEL_IVA (3 << 8) /* iva1 - 200MHz */ +#define RII_SYNC_IVA (0 << 13) /* Bypass sync */ +#define RII_CM_CLKSEL_DSP_VAL (RII_SYNC_IVA | RII_CLKSEL_IVA | \ + RII_SYNC_DSP | RII_CLKSEL_DSP_IF | \ + RII_CLKSEL_DSP) +#define RII_CLKSEL_GFX (2 << 0) /* 50MHz */ +#define RII_CM_CLKSEL_GFX_VAL RII_CLKSEL_GFX + +/* 2420-PRCM I 660MHz core */ +#define RI_CLKSEL_L3 (4 << 0) /* 165MHz */ +#define RI_CLKSEL_L4 (2 << 5) /* 82.5MHz */ +#define RI_CLKSEL_USB (4 << 25) /* 41.25MHz */ +#define RI_CM_CLKSEL1_CORE_VAL (RI_CLKSEL_USB | \ + RXX_CLKSEL_SSI | RXX_CLKSEL_VLYNQ | \ + RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ + RI_CLKSEL_L4 | RI_CLKSEL_L3) +#define RI_CLKSEL_MPU (2 << 0) /* 330MHz */ +#define RI_CM_CLKSEL_MPU_VAL RI_CLKSEL_MPU +#define RI_CLKSEL_DSP (3 << 0) /* c5x - 220MHz */ +#define RI_CLKSEL_DSP_IF (2 << 5) /* c5x - 110MHz */ +#define RI_SYNC_DSP (1 << 7) /* Activate sync */ +#define RI_CLKSEL_IVA (4 << 8) /* iva1 - 165MHz */ +#define RI_SYNC_IVA (0 << 13) /* Bypass sync */ +#define RI_CM_CLKSEL_DSP_VAL (RI_SYNC_IVA | RI_CLKSEL_IVA | \ + RI_SYNC_DSP | RI_CLKSEL_DSP_IF | \ + RI_CLKSEL_DSP) +#define RI_CLKSEL_GFX (1 << 0) /* 165MHz */ +#define RI_CM_CLKSEL_GFX_VAL RI_CLKSEL_GFX + +/* 2420-PRCM VII (boot) */ +#define RVII_CLKSEL_L3 (1 << 0) +#define RVII_CLKSEL_L4 (1 << 5) +#define RVII_CLKSEL_DSS1 (1 << 8) +#define RVII_CLKSEL_DSS2 (0 << 13) +#define RVII_CLKSEL_VLYNQ (1 << 15) +#define RVII_CLKSEL_SSI (1 << 20) +#define RVII_CLKSEL_USB (1 << 25) + +#define RVII_CM_CLKSEL1_CORE_VAL (RVII_CLKSEL_USB | RVII_CLKSEL_SSI | \ + RVII_CLKSEL_VLYNQ | \ + RVII_CLKSEL_DSS2 | RVII_CLKSEL_DSS1 | \ + RVII_CLKSEL_L4 | RVII_CLKSEL_L3) + +#define RVII_CLKSEL_MPU (1 << 0) /* all divide by 1 */ +#define RVII_CM_CLKSEL_MPU_VAL RVII_CLKSEL_MPU + +#define RVII_CLKSEL_DSP (1 << 0) +#define RVII_CLKSEL_DSP_IF (1 << 5) +#define RVII_SYNC_DSP (0 << 7) +#define RVII_CLKSEL_IVA (1 << 8) +#define RVII_SYNC_IVA (0 << 13) +#define RVII_CM_CLKSEL_DSP_VAL (RVII_SYNC_IVA | RVII_CLKSEL_IVA | \ + RVII_SYNC_DSP | RVII_CLKSEL_DSP_IF | \ + RVII_CLKSEL_DSP) + +#define RVII_CLKSEL_GFX (1 << 0) +#define RVII_CM_CLKSEL_GFX_VAL RVII_CLKSEL_GFX + +/*------------------------------------------------------------------------- + * 2430 Target modes: Along with each configuration the CPU has several + * modes which goes along with them. Modes mainly are the addition of + * describe DPLL combinations to go along with a ratio. + *-------------------------------------------------------------------------*/ + +/* Hardware governed */ +#define MX_48M_SRC (0 << 3) +#define MX_54M_SRC (0 << 5) +#define MX_APLLS_CLIKIN_12 (3 << 23) +#define MX_APLLS_CLIKIN_13 (2 << 23) +#define MX_APLLS_CLIKIN_19_2 (0 << 23) + +/* + * 2430 - standalone, 2*ref*M/(n+1), M/N is for exactness not relock speed + * #5a (ratio1) baseport-target, target DPLL = 266*2 = 532MHz + */ +#define M5A_DPLL_MULT_12 (133 << 12) +#define M5A_DPLL_DIV_12 (5 << 8) +#define M5A_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + M5A_DPLL_DIV_12 | M5A_DPLL_MULT_12 | \ + MX_APLLS_CLIKIN_12) +#define M5A_DPLL_MULT_13 (61 << 12) +#define M5A_DPLL_DIV_13 (2 << 8) +#define M5A_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + M5A_DPLL_DIV_13 | M5A_DPLL_MULT_13 | \ + MX_APLLS_CLIKIN_13) +#define M5A_DPLL_MULT_19 (55 << 12) +#define M5A_DPLL_DIV_19 (3 << 8) +#define M5A_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ + M5A_DPLL_DIV_19 | M5A_DPLL_MULT_19 | \ + MX_APLLS_CLIKIN_19_2) +/* #5b (ratio1) target DPLL = 200*2 = 400MHz */ +#define M5B_DPLL_MULT_12 (50 << 12) +#define M5B_DPLL_DIV_12 (2 << 8) +#define M5B_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + M5B_DPLL_DIV_12 | M5B_DPLL_MULT_12 | \ + MX_APLLS_CLIKIN_12) +#define M5B_DPLL_MULT_13 (200 << 12) +#define M5B_DPLL_DIV_13 (12 << 8) + +#define M5B_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + M5B_DPLL_DIV_13 | M5B_DPLL_MULT_13 | \ + MX_APLLS_CLIKIN_13) +#define M5B_DPLL_MULT_19 (125 << 12) +#define M5B_DPLL_DIV_19 (31 << 8) +#define M5B_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ + M5B_DPLL_DIV_19 | M5B_DPLL_MULT_19 | \ + MX_APLLS_CLIKIN_19_2) +/* + * #4 (ratio2), DPLL = 399*2 = 798MHz, L3=133MHz + */ +#define M4_DPLL_MULT_12 (133 << 12) +#define M4_DPLL_DIV_12 (3 << 8) +#define M4_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + M4_DPLL_DIV_12 | M4_DPLL_MULT_12 | \ + MX_APLLS_CLIKIN_12) + +#define M4_DPLL_MULT_13 (399 << 12) +#define M4_DPLL_DIV_13 (12 << 8) +#define M4_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + M4_DPLL_DIV_13 | M4_DPLL_MULT_13 | \ + MX_APLLS_CLIKIN_13) + +#define M4_DPLL_MULT_19 (145 << 12) +#define M4_DPLL_DIV_19 (6 << 8) +#define M4_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ + M4_DPLL_DIV_19 | M4_DPLL_MULT_19 | \ + MX_APLLS_CLIKIN_19_2) + +/* + * #3 (ratio2) baseport-target, target DPLL = 330*2 = 660MHz + */ +#define M3_DPLL_MULT_12 (55 << 12) +#define M3_DPLL_DIV_12 (1 << 8) +#define M3_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + M3_DPLL_DIV_12 | M3_DPLL_MULT_12 | \ + MX_APLLS_CLIKIN_12) +#define M3_DPLL_MULT_13 (76 << 12) +#define M3_DPLL_DIV_13 (2 << 8) +#define M3_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + M3_DPLL_DIV_13 | M3_DPLL_MULT_13 | \ + MX_APLLS_CLIKIN_13) +#define M3_DPLL_MULT_19 (17 << 12) +#define M3_DPLL_DIV_19 (0 << 8) +#define M3_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ + M3_DPLL_DIV_19 | M3_DPLL_MULT_19 | \ + MX_APLLS_CLIKIN_19_2) + +/* + * #2 (ratio1) DPLL = 330*2 = 660MHz, L3=165MHz + */ +#define M2_DPLL_MULT_12 (55 << 12) +#define M2_DPLL_DIV_12 (1 << 8) +#define M2_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + M2_DPLL_DIV_12 | M2_DPLL_MULT_12 | \ + MX_APLLS_CLIKIN_12) + +/* Speed changes - Used 658.7MHz instead of 660MHz for LP-Refresh M=76 N=2, + * relock time issue */ +/* Core frequency changed from 330/165 to 329/164 MHz*/ +#define M2_DPLL_MULT_13 (76 << 12) +#define M2_DPLL_DIV_13 (2 << 8) +#define M2_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + M2_DPLL_DIV_13 | M2_DPLL_MULT_13 | \ + MX_APLLS_CLIKIN_13) + +#define M2_DPLL_MULT_19 (17 << 12) +#define M2_DPLL_DIV_19 (0 << 8) +#define M2_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ + M2_DPLL_DIV_19 | M2_DPLL_MULT_19 | \ + MX_APLLS_CLIKIN_19_2) + +/* boot (boot) */ +#define MB_DPLL_MULT (1 << 12) +#define MB_DPLL_DIV (0 << 8) +#define MB_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + MB_DPLL_DIV | MB_DPLL_MULT | \ + MX_APLLS_CLIKIN_12) + +#define MB_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + MB_DPLL_DIV | MB_DPLL_MULT | \ + MX_APLLS_CLIKIN_13) + +#define MB_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ + MB_DPLL_DIV | MB_DPLL_MULT | \ + MX_APLLS_CLIKIN_19) + +/* + * 2430 - chassis (sedna) + * 165 (ratio1) same as above #2 + * 150 (ratio1) + * 133 (ratio2) same as above #4 + * 110 (ratio2) same as above #3 + * 104 (ratio2) + * boot (boot) + */ + +/* PRCM I target DPLL = 2*330MHz = 660MHz */ +#define MI_DPLL_MULT_12 (55 << 12) +#define MI_DPLL_DIV_12 (1 << 8) +#define MI_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + MI_DPLL_DIV_12 | MI_DPLL_MULT_12 | \ + MX_APLLS_CLIKIN_12) + +/* + * 2420 Equivalent - mode registers + * PRCM II , target DPLL = 2*300MHz = 600MHz + */ +#define MII_DPLL_MULT_12 (50 << 12) +#define MII_DPLL_DIV_12 (1 << 8) +#define MII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + MII_DPLL_DIV_12 | MII_DPLL_MULT_12 | \ + MX_APLLS_CLIKIN_12) +#define MII_DPLL_MULT_13 (300 << 12) +#define MII_DPLL_DIV_13 (12 << 8) +#define MII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + MII_DPLL_DIV_13 | MII_DPLL_MULT_13 | \ + MX_APLLS_CLIKIN_13) + +/* PRCM III target DPLL = 2*266 = 532MHz*/ +#define MIII_DPLL_MULT_12 (133 << 12) +#define MIII_DPLL_DIV_12 (5 << 8) +#define MIII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ + MIII_DPLL_DIV_12 | \ + MIII_DPLL_MULT_12 | MX_APLLS_CLIKIN_12) +#define MIII_DPLL_MULT_13 (266 << 12) +#define MIII_DPLL_DIV_13 (12 << 8) +#define MIII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ + MIII_DPLL_DIV_13 | \ + MIII_DPLL_MULT_13 | MX_APLLS_CLIKIN_13) + +/* PRCM VII (boot bypass) */ +#define MVII_CM_CLKSEL1_PLL_12_VAL MB_CM_CLKSEL1_PLL_12_VAL +#define MVII_CM_CLKSEL1_PLL_13_VAL MB_CM_CLKSEL1_PLL_13_VAL + +/* High and low operation value */ +#define MX_CLKSEL2_PLL_2x_VAL (2 << 0) +#define MX_CLKSEL2_PLL_1x_VAL (1 << 0) + +/* MPU speed defines */ +#define S12M 12000000 +#define S13M 13000000 +#define S19M 19200000 +#define S26M 26000000 +#define S100M 100000000 +#define S133M 133000000 +#define S150M 150000000 +#define S164M 164000000 +#define S165M 165000000 +#define S199M 199000000 +#define S200M 200000000 +#define S266M 266000000 +#define S300M 300000000 +#define S329M 329000000 +#define S330M 330000000 +#define S399M 399000000 +#define S400M 400000000 +#define S532M 532000000 +#define S600M 600000000 +#define S658M 658000000 +#define S660M 660000000 +#define S798M 798000000 + + +extern const struct prcm_config omap2420_rate_table[]; +extern const struct prcm_config omap2430_rate_table[]; +extern const struct prcm_config *rate_table; +extern const struct prcm_config *curr_prcm_set; + +#endif |
