diff options
Diffstat (limited to 'arch/arm/mach-bcmring/include/mach/reg_umi.h')
| -rw-r--r-- | arch/arm/mach-bcmring/include/mach/reg_umi.h | 237 |
1 files changed, 0 insertions, 237 deletions
diff --git a/arch/arm/mach-bcmring/include/mach/reg_umi.h b/arch/arm/mach-bcmring/include/mach/reg_umi.h deleted file mode 100644 index 0992842caa77..000000000000 --- a/arch/arm/mach-bcmring/include/mach/reg_umi.h +++ /dev/null @@ -1,237 +0,0 @@ -/***************************************************************************** -* Copyright 2005 - 2008 Broadcom Corporation. All rights reserved. -* -* Unless you and Broadcom execute a separate written software license -* agreement governing use of this software, this software is licensed to you -* under the terms of the GNU General Public License version 2, available at -* http://www.broadcom.com/licenses/GPLv2.php (the "GPL"). -* -* Notwithstanding the above, under no circumstances may you combine this -* software in any way with any other Broadcom software provided under a -* license other than the GPL, without Broadcom's express prior written -* consent. -*****************************************************************************/ - -/* -* -***************************************************************************** -* -* REG_UMI.h -* -* PURPOSE: -* -* This file contains definitions for the nand registers: -* -* NOTES: -* -*****************************************************************************/ - -#if !defined(__ASM_ARCH_REG_UMI_H) -#define __ASM_ARCH_REG_UMI_H - -/* ---- Include Files ---------------------------------------------------- */ -#include <csp/reg.h> -#include <mach/csp/mm_io.h> - -/* ---- Constants and Types ---------------------------------------------- */ - -/* Unified Memory Interface Ctrl Register */ -#define HW_UMI_BASE MM_IO_BASE_UMI - -/* Flash bank 0 timing and control register */ -#define REG_UMI_FLASH0_TCR __REG32(HW_UMI_BASE + 0x00) -/* Flash bank 1 timing and control register */ -#define REG_UMI_FLASH1_TCR __REG32(HW_UMI_BASE + 0x04) -/* Flash bank 2 timing and control register */ -#define REG_UMI_FLASH2_TCR __REG32(HW_UMI_BASE + 0x08) -/* MMD interface and control register */ -#define REG_UMI_MMD_ICR __REG32(HW_UMI_BASE + 0x0c) -/* NAND timing and control register */ -#define REG_UMI_NAND_TCR __REG32(HW_UMI_BASE + 0x18) -/* NAND ready/chip select register */ -#define REG_UMI_NAND_RCSR __REG32(HW_UMI_BASE + 0x1c) -/* NAND ECC control & status register */ -#define REG_UMI_NAND_ECC_CSR __REG32(HW_UMI_BASE + 0x20) -/* NAND ECC data register XXB2B1B0 */ -#define REG_UMI_NAND_ECC_DATA __REG32(HW_UMI_BASE + 0x24) -/* BCH ECC Parameter N */ -#define REG_UMI_BCH_N __REG32(HW_UMI_BASE + 0x40) -/* BCH ECC Parameter T */ -#define REG_UMI_BCH_K __REG32(HW_UMI_BASE + 0x44) -/* BCH ECC Parameter K */ -#define REG_UMI_BCH_T __REG32(HW_UMI_BASE + 0x48) -/* BCH ECC Contro Status */ -#define REG_UMI_BCH_CTRL_STATUS __REG32(HW_UMI_BASE + 0x4C) -/* BCH WR ECC 31:0 */ -#define REG_UMI_BCH_WR_ECC_0 __REG32(HW_UMI_BASE + 0x50) -/* BCH WR ECC 63:32 */ -#define REG_UMI_BCH_WR_ECC_1 __REG32(HW_UMI_BASE + 0x54) -/* BCH WR ECC 95:64 */ -#define REG_UMI_BCH_WR_ECC_2 __REG32(HW_UMI_BASE + 0x58) -/* BCH WR ECC 127:96 */ -#define REG_UMI_BCH_WR_ECC_3 __REG32(HW_UMI_BASE + 0x5c) -/* BCH WR ECC 155:128 */ -#define REG_UMI_BCH_WR_ECC_4 __REG32(HW_UMI_BASE + 0x60) -/* BCH Read Error Location 1,0 */ -#define REG_UMI_BCH_RD_ERR_LOC_1_0 __REG32(HW_UMI_BASE + 0x64) -/* BCH Read Error Location 3,2 */ -#define REG_UMI_BCH_RD_ERR_LOC_3_2 __REG32(HW_UMI_BASE + 0x68) -/* BCH Read Error Location 5,4 */ -#define REG_UMI_BCH_RD_ERR_LOC_5_4 __REG32(HW_UMI_BASE + 0x6c) -/* BCH Read Error Location 7,6 */ -#define REG_UMI_BCH_RD_ERR_LOC_7_6 __REG32(HW_UMI_BASE + 0x70) -/* BCH Read Error Location 9,8 */ -#define REG_UMI_BCH_RD_ERR_LOC_9_8 __REG32(HW_UMI_BASE + 0x74) -/* BCH Read Error Location 11,10 */ -#define REG_UMI_BCH_RD_ERR_LOC_B_A __REG32(HW_UMI_BASE + 0x78) - -/* REG_UMI_FLASH0/1/2_TCR, REG_UMI_SRAM0/1_TCR bits */ -/* Enable wait pin during burst write or read */ -#define REG_UMI_TCR_WAITEN 0x80000000 -/* Enable mem ctrlr to work with ext mem of lower freq than AHB clk */ -#define REG_UMI_TCR_LOWFREQ 0x40000000 -/* 1=synch write, 0=async write */ -#define REG_UMI_TCR_MEMTYPE_SYNCWRITE 0x20000000 -/* 1=synch read, 0=async read */ -#define REG_UMI_TCR_MEMTYPE_SYNCREAD 0x10000000 -/* 1=page mode read, 0=normal mode read */ -#define REG_UMI_TCR_MEMTYPE_PAGEREAD 0x08000000 -/* page size/burst size (wrap only) */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_MASK 0x07000000 -/* 4 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_4 0x00000000 -/* 8 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_8 0x01000000 -/* 16 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_16 0x02000000 -/* 32 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_32 0x03000000 -/* 64 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_64 0x04000000 -/* 128 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_128 0x05000000 -/* 256 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_256 0x06000000 -/* 512 word */ -#define REG_UMI_TCR_MEMTYPE_PGSZ_512 0x07000000 -/* Page read access cycle / Burst write latency (n+2 / n+1) */ -#define REG_UMI_TCR_TPRC_TWLC_MASK 0x00f80000 -/* Bus turnaround cycle (n) */ -#define REG_UMI_TCR_TBTA_MASK 0x00070000 -/* Write pulse width cycle (n+1) */ -#define REG_UMI_TCR_TWP_MASK 0x0000f800 -/* Write recovery cycle (n+1) */ -#define REG_UMI_TCR_TWR_MASK 0x00000600 -/* Write address setup cycle (n+1) */ -#define REG_UMI_TCR_TAS_MASK 0x00000180 -/* Output enable delay cycle (n) */ -#define REG_UMI_TCR_TOE_MASK 0x00000060 -/* Read access cycle / Burst read latency (n+2 / n+1) */ -#define REG_UMI_TCR_TRC_TLC_MASK 0x0000001f - -/* REG_UMI_MMD_ICR bits */ -/* Flash write protection pin control */ -#define REG_UMI_MMD_ICR_FLASH_WP 0x8000 -/* Extend hold time for sram0, sram1 csn (39 MHz operation) */ -#define REG_UMI_MMD_ICR_XHCS 0x4000 -/* Enable SDRAM 2 interface control */ -#define REG_UMI_MMD_ICR_SDRAM2EN 0x2000 -/* Enable merge of flash banks 0/1 to 512 MBit bank */ -#define REG_UMI_MMD_ICR_INST512 0x1000 -/* Enable merge of flash banks 1/2 to 512 MBit bank */ -#define REG_UMI_MMD_ICR_DATA512 0x0800 -/* Enable SDRAM interface control */ -#define REG_UMI_MMD_ICR_SDRAMEN 0x0400 -/* Polarity of busy state of Burst Wait Signal */ -#define REG_UMI_MMD_ICR_WAITPOL 0x0200 -/* Enable burst clock stopped when not accessing external burst flash/sram */ -#define REG_UMI_MMD_ICR_BCLKSTOP 0x0100 -/* Enable the peri1_csn to replace flash1_csn in 512 Mb flash mode */ -#define REG_UMI_MMD_ICR_PERI1EN 0x0080 -/* Enable the peri2_csn to replace sdram_csn */ -#define REG_UMI_MMD_ICR_PERI2EN 0x0040 -/* Enable the peri3_csn to replace sdram2_csn */ -#define REG_UMI_MMD_ICR_PERI3EN 0x0020 -/* Enable sram bank1 for H/W controlled MRS */ -#define REG_UMI_MMD_ICR_MRSB1 0x0010 -/* Enable sram bank0 for H/W controlled MRS */ -#define REG_UMI_MMD_ICR_MRSB0 0x0008 -/* Polarity for assert3ed state of H/W controlled MRS */ -#define REG_UMI_MMD_ICR_MRSPOL 0x0004 -/* 0: S/W controllable ZZ/MRS/CRE/P-Mode pin */ -/* 1: H/W controlled ZZ/MRS/CRE/P-Mode, same timing as CS */ -#define REG_UMI_MMD_ICR_MRSMODE 0x0002 -/* MRS state for S/W controlled mode */ -#define REG_UMI_MMD_ICR_MRSSTATE 0x0001 - -/* REG_UMI_NAND_TCR bits */ -/* Enable software to control CS */ -#define REG_UMI_NAND_TCR_CS_SWCTRL 0x80000000 -/* 16-bit nand wordsize if set */ -#define REG_UMI_NAND_TCR_WORD16 0x40000000 -/* Bus turnaround cycle (n) */ -#define REG_UMI_NAND_TCR_TBTA_MASK 0x00070000 -/* Write pulse width cycle (n+1) */ -#define REG_UMI_NAND_TCR_TWP_MASK 0x0000f800 -/* Write recovery cycle (n+1) */ -#define REG_UMI_NAND_TCR_TWR_MASK 0x00000600 -/* Write address setup cycle (n+1) */ -#define REG_UMI_NAND_TCR_TAS_MASK 0x00000180 -/* Output enable delay cycle (n) */ -#define REG_UMI_NAND_TCR_TOE_MASK 0x00000060 -/* Read access cycle (n+2) */ -#define REG_UMI_NAND_TCR_TRC_TLC_MASK 0x0000001f - -/* REG_UMI_NAND_RCSR bits */ -/* Status: Ready=1, Busy=0 */ -#define REG_UMI_NAND_RCSR_RDY 0x02 -/* Keep CS asserted during operation */ -#define REG_UMI_NAND_RCSR_CS_ASSERTED 0x01 - -/* REG_UMI_NAND_ECC_CSR bits */ -/* Interrupt status - read-only */ -#define REG_UMI_NAND_ECC_CSR_NANDINT 0x80000000 -/* Read: Status of ECC done, Write: clear ECC interrupt */ -#define REG_UMI_NAND_ECC_CSR_ECCINT_RAW 0x00800000 -/* Read: Status of R/B, Write: clear R/B interrupt */ -#define REG_UMI_NAND_ECC_CSR_RBINT_RAW 0x00400000 -/* 1 = Enable ECC Interrupt */ -#define REG_UMI_NAND_ECC_CSR_ECCINT_ENABLE 0x00008000 -/* 1 = Assert interrupt at rising edge of R/B_ */ -#define REG_UMI_NAND_ECC_CSR_RBINT_ENABLE 0x00004000 -/* Calculate ECC by 0=512 bytes, 1=256 bytes */ -#define REG_UMI_NAND_ECC_CSR_256BYTE 0x00000080 -/* Enable ECC in hardware */ -#define REG_UMI_NAND_ECC_CSR_ECC_ENABLE 0x00000001 - -/* REG_UMI_BCH_CTRL_STATUS bits */ -/* Shift to Indicate Number of correctable errors detected */ -#define REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR_SHIFT 20 -/* Indicate Number of correctable errors detected */ -#define REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR 0x00F00000 -/* Indicate Errors detected during read but uncorrectable */ -#define REG_UMI_BCH_CTRL_STATUS_UNCORR_ERR 0x00080000 -/* Indicate Errors detected during read and are correctable */ -#define REG_UMI_BCH_CTRL_STATUS_CORR_ERR 0x00040000 -/* Flag indicates BCH's ECC status of read process are valid */ -#define REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID 0x00020000 -/* Flag indicates BCH's ECC status of write process are valid */ -#define REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID 0x00010000 -/* Pause ECC calculation */ -#define REG_UMI_BCH_CTRL_STATUS_PAUSE_ECC_DEC 0x00000010 -/* Enable Interrupt */ -#define REG_UMI_BCH_CTRL_STATUS_INT_EN 0x00000004 -/* Enable ECC during read */ -#define REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN 0x00000002 -/* Enable ECC during write */ -#define REG_UMI_BCH_CTRL_STATUS_ECC_WR_EN 0x00000001 -/* Mask for location */ -#define REG_UMI_BCH_ERR_LOC_MASK 0x00001FFF -/* location within a byte */ -#define REG_UMI_BCH_ERR_LOC_BYTE 0x00000007 -/* location within a word */ -#define REG_UMI_BCH_ERR_LOC_WORD 0x00000018 -/* location within a page (512 byte) */ -#define REG_UMI_BCH_ERR_LOC_PAGE 0x00001FE0 -#define REG_UMI_BCH_ERR_LOC_ADDR(index) (__REG32(HW_UMI_BASE + 0x64 + (index / 2)*4) >> ((index % 2) * 16)) -#endif |
