diff options
Diffstat (limited to 'Documentation/gpio/board.txt')
| -rw-r--r-- | Documentation/gpio/board.txt | 115 |
1 files changed, 115 insertions, 0 deletions
diff --git a/Documentation/gpio/board.txt b/Documentation/gpio/board.txt new file mode 100644 index 000000000000..0d03506f2cc5 --- /dev/null +++ b/Documentation/gpio/board.txt @@ -0,0 +1,115 @@ +GPIO Mappings +============= + +This document explains how GPIOs can be assigned to given devices and functions. +Note that it only applies to the new descriptor-based interface. For a +description of the deprecated integer-based GPIO interface please refer to +gpio-legacy.txt (actually, there is no real mapping possible with the old +interface; you just fetch an integer from somewhere and request the +corresponding GPIO. + +Platforms that make use of GPIOs must select ARCH_REQUIRE_GPIOLIB (if GPIO usage +is mandatory) or ARCH_WANT_OPTIONAL_GPIOLIB (if GPIO support can be omitted) in +their Kconfig. Then, how GPIOs are mapped depends on what the platform uses to +describe its hardware layout. Currently, mappings can be defined through device +tree, ACPI, and platform data. + +Device Tree +----------- +GPIOs can easily be mapped to devices and functions in the device tree. The +exact way to do it depends on the GPIO controller providing the GPIOs, see the +device tree bindings for your controller. + +GPIOs mappings are defined in the consumer device's node, in a property named +<function>-gpios, where <function> is the function the driver will request +through gpiod_get(). For example: + + foo_device { + compatible = "acme,foo"; + ... + led-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>, /* red */ + <&gpio 16 GPIO_ACTIVE_HIGH>, /* green */ + <&gpio 17 GPIO_ACTIVE_HIGH>; /* blue */ + + power-gpio = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + +This property will make GPIOs 15, 16 and 17 available to the driver under the +"led" function, and GPIO 1 as the "power" GPIO: + + struct gpio_desc *red, *green, *blue, *power; + + red = gpiod_get_index(dev, "led", 0); + green = gpiod_get_index(dev, "led", 1); + blue = gpiod_get_index(dev, "led", 2); + + power = gpiod_get(dev, "power"); + +The led GPIOs will be active-high, while the power GPIO will be active-low (i.e. +gpiod_is_active_low(power) will be true). + +ACPI +---- +ACPI does not support function names for GPIOs. Therefore, only the "idx" +argument of gpiod_get_index() is useful to discriminate between GPIOs assigned +to a device. The "con_id" argument can still be set for debugging purposes (it +will appear under error messages as well as debug and sysfs nodes). + +Platform Data +------------- +Finally, GPIOs can be bound to devices and functions using platform data. Board +files that desire to do so need to include the following header: + + #include <linux/gpio/driver.h> + +GPIOs are mapped by the means of tables of lookups, containing instances of the +gpiod_lookup structure. Two macros are defined to help declaring such mappings: + + GPIO_LOOKUP(chip_label, chip_hwnum, dev_id, con_id, flags) + GPIO_LOOKUP_IDX(chip_label, chip_hwnum, dev_id, con_id, idx, flags) + +where + + - chip_label is the label of the gpiod_chip instance providing the GPIO + - chip_hwnum is the hardware number of the GPIO within the chip + - dev_id is the identifier of the device that will make use of this GPIO. If + NULL, the GPIO will be available to all devices. + - con_id is the name of the GPIO function from the device point of view. It + can be NULL. + - idx is the index of the GPIO within the function. + - flags is defined to specify the following properties: + * GPIOF_ACTIVE_LOW - to configure the GPIO as active-low + * GPIOF_OPEN_DRAIN - GPIO pin is open drain type. + * GPIOF_OPEN_SOURCE - GPIO pin is open source type. + +In the future, these flags might be extended to support more properties. + +Note that GPIO_LOOKUP() is just a shortcut to GPIO_LOOKUP_IDX() where idx = 0. + +A lookup table can then be defined as follows: + + struct gpiod_lookup gpios_table[] = { + GPIO_LOOKUP_IDX("gpio.0", 15, "foo.0", "led", 0, GPIO_ACTIVE_HIGH), + GPIO_LOOKUP_IDX("gpio.0", 16, "foo.0", "led", 1, GPIO_ACTIVE_HIGH), + GPIO_LOOKUP_IDX("gpio.0", 17, "foo.0", "led", 2, GPIO_ACTIVE_HIGH), + GPIO_LOOKUP("gpio.0", 1, "foo.0", "power", GPIO_ACTIVE_LOW), + }; + +And the table can be added by the board code as follows: + + gpiod_add_table(gpios_table, ARRAY_SIZE(gpios_table)); + +The driver controlling "foo.0" will then be able to obtain its GPIOs as follows: + + struct gpio_desc *red, *green, *blue, *power; + + red = gpiod_get_index(dev, "led", 0); + green = gpiod_get_index(dev, "led", 1); + blue = gpiod_get_index(dev, "led", 2); + + power = gpiod_get(dev, "power"); + gpiod_direction_output(power, 1); + +Since the "power" GPIO is mapped as active-low, its actual signal will be 0 +after this code. Contrary to the legacy integer GPIO interface, the active-low +property is handled during mapping and is thus transparent to GPIO consumers. |
