diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
13 files changed, 186 insertions, 205 deletions
diff --git a/Documentation/devicetree/bindings/memory.txt b/Documentation/devicetree/bindings/memory.txt deleted file mode 100644 index eb2469365593..000000000000 --- a/Documentation/devicetree/bindings/memory.txt +++ /dev/null @@ -1,168 +0,0 @@ -*** Memory binding *** - -The /memory node provides basic information about the address and size -of the physical memory. This node is usually filled or updated by the -bootloader, depending on the actual memory configuration of the given -hardware. - -The memory layout is described by the following node: - -/ { - #address-cells = <(n)>; - #size-cells = <(m)>; - memory { - device_type = "memory"; - reg = <(baseaddr1) (size1) - (baseaddr2) (size2) - ... - (baseaddrN) (sizeN)>; - }; - ... -}; - -A memory node follows the typical device tree rules for "reg" property: -n: number of cells used to store base address value -m: number of cells used to store size value -baseaddrX: defines a base address of the defined memory bank -sizeX: the size of the defined memory bank - - -More than one memory bank can be defined. - - -*** Reserved memory regions *** - -In /memory/reserved-memory node one can create child nodes describing -particular reserved (excluded from normal use) memory regions. Such -memory regions are usually designed for the special usage by various -device drivers. A good example are contiguous memory allocations or -memory sharing with other operating system on the same hardware board. -Those special memory regions might depend on the board configuration and -devices used on the target system. - -Parameters for each memory region can be encoded into the device tree -with the following convention: - -[(label):] (name) { - compatible = "linux,contiguous-memory-region", "reserved-memory-region"; - reg = <(address) (size)>; - (linux,default-contiguous-region); -}; - -compatible: one or more of: - - "linux,contiguous-memory-region" - enables binding of this - region to Contiguous Memory Allocator (special region for - contiguous memory allocations, shared with movable system - memory, Linux kernel-specific). - - "reserved-memory-region" - compatibility is defined, given - region is assigned for exclusive usage for by the respective - devices. - -reg: standard property defining the base address and size of - the memory region - -linux,default-contiguous-region: property indicating that the region - is the default region for all contiguous memory - allocations, Linux specific (optional) - -It is optional to specify the base address, so if one wants to use -autoconfiguration of the base address, '0' can be specified as a base -address in the 'reg' property. - -The /memory/reserved-memory node must contain the same #address-cells -and #size-cells value as the root node. - - -*** Device node's properties *** - -Once regions in the /memory/reserved-memory node have been defined, they -may be referenced by other device nodes. Bindings that wish to reference -memory regions should explicitly document their use of the following -property: - -memory-region = <&phandle_to_defined_region>; - -This property indicates that the device driver should use the memory -region pointed by the given phandle. - - -*** Example *** - -This example defines a memory consisting of 4 memory banks. 3 contiguous -regions are defined for Linux kernel, one default of all device drivers -(named contig_mem, placed at 0x72000000, 64MiB), one dedicated to the -framebuffer device (labelled display_mem, placed at 0x78000000, 8MiB) -and one for multimedia processing (labelled multimedia_mem, placed at -0x77000000, 64MiB). 'display_mem' region is then assigned to fb@12300000 -device for DMA memory allocations (Linux kernel drivers will use CMA is -available or dma-exclusive usage otherwise). 'multimedia_mem' is -assigned to scaler@12500000 and codec@12600000 devices for contiguous -memory allocations when CMA driver is enabled. - -The reason for creating a separate region for framebuffer device is to -match the framebuffer base address to the one configured by bootloader, -so once Linux kernel drivers starts no glitches on the displayed boot -logo appears. Scaller and codec drivers should share the memory -allocations. - -/ { - #address-cells = <1>; - #size-cells = <1>; - - /* ... */ - - memory { - reg = <0x40000000 0x10000000 - 0x50000000 0x10000000 - 0x60000000 0x10000000 - 0x70000000 0x10000000>; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - - /* - * global autoconfigured region for contiguous allocations - * (used only with Contiguous Memory Allocator) - */ - contig_region@0 { - compatible = "linux,contiguous-memory-region"; - reg = <0x0 0x4000000>; - linux,default-contiguous-region; - }; - - /* - * special region for framebuffer - */ - display_region: region@78000000 { - compatible = "linux,contiguous-memory-region", "reserved-memory-region"; - reg = <0x78000000 0x800000>; - }; - - /* - * special region for multimedia processing devices - */ - multimedia_region: region@77000000 { - compatible = "linux,contiguous-memory-region"; - reg = <0x77000000 0x4000000>; - }; - }; - }; - - /* ... */ - - fb0: fb@12300000 { - status = "okay"; - memory-region = <&display_region>; - }; - - scaler: scaler@12500000 { - status = "okay"; - memory-region = <&multimedia_region>; - }; - - codec: codec@12600000 { - status = "okay"; - memory-region = <&multimedia_region>; - }; -}; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index 6d1c0988cfc7..c67b975c8906 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -1,11 +1,11 @@ -* Samsung Exynos specific extensions to the Synopsis Designware Mobile +* Samsung Exynos specific extensions to the Synopsys Designware Mobile Storage Host Controller -The Synopsis designware mobile storage host controller is used to interface +The Synopsys designware mobile storage host controller is used to interface a SoC with storage medium such as eMMC or SD/MMC cards. This file documents -differences between the core Synopsis dw mshc controller properties described -by synopsis-dw-mshc.txt and the properties used by the Samsung Exynos specific -extensions to the Synopsis Designware Mobile Storage Host Controller. +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Samsung Exynos specific +extensions to the Synopsys Designware Mobile Storage Host Controller. Required Properties: diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index 8a3d91d47b6a..c559f3f36309 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -1,11 +1,11 @@ -* Rockchip specific extensions to the Synopsis Designware Mobile +* Rockchip specific extensions to the Synopsys Designware Mobile Storage Host Controller -The Synopsis designware mobile storage host controller is used to interface +The Synopsys designware mobile storage host controller is used to interface a SoC with storage medium such as eMMC or SD/MMC cards. This file documents -differences between the core Synopsis dw mshc controller properties described -by synopsis-dw-mshc.txt and the properties used by the Rockchip specific -extensions to the Synopsis Designware Mobile Storage Host Controller. +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Rockchip specific +extensions to the Synopsys Designware Mobile Storage Host Controller. Required Properties: diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index cdcebea9c6f5..066a78b034ca 100644 --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -1,14 +1,14 @@ -* Synopsis Designware Mobile Storage Host Controller +* Synopsys Designware Mobile Storage Host Controller -The Synopsis designware mobile storage host controller is used to interface +The Synopsys designware mobile storage host controller is used to interface a SoC with storage medium such as eMMC or SD/MMC cards. This file documents differences between the core mmc properties described by mmc.txt and the -properties used by the Synopsis Designware Mobile Storage Host Controller. +properties used by the Synopsys Designware Mobile Storage Host Controller. Required Properties: * compatible: should be - - snps,dw-mshc: for controllers compliant with synopsis dw-mshc. + - snps,dw-mshc: for controllers compliant with synopsys dw-mshc. * #address-cells: should be 1. * #size-cells: should be 0. diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index df204e18e030..6a2a1160a70d 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -9,12 +9,15 @@ compulsory and any optional properties, common to all SD/MMC drivers, as described in mmc.txt, can be used. Additionally the following tmio_mmc-specific optional bindings can be used. +Required properties: +- compatible: "renesas,sdhi-shmobile" - a generic sh-mobile SDHI unit + "renesas,sdhi-sh7372" - SDHI IP on SH7372 SoC + "renesas,sdhi-sh73a0" - SDHI IP on SH73A0 SoC + "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC + "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC + "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC + "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC + "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC + Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable - -When used with Renesas SDHI hardware, the following compatibility strings -configure various model-specific properties: - -"renesas,sh7372-sdhi": (default) compatible with SH7372 -"renesas,r8a7740-sdhi": compatible with R8A7740: certain MMC/SD commands have to - wait for the interface to become idle. diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index 2c6be0377f55..d2ea4605d078 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -86,6 +86,7 @@ General Properties: Clock Properties: + - fsl,cksel Timer reference clock source. - fsl,tclk-period Timer reference clock period in nanoseconds. - fsl,tmr-prsc Prescaler, divides the output clock. - fsl,tmr-add Frequency compensation value. @@ -97,7 +98,7 @@ Clock Properties: clock. You must choose these carefully for the clock to work right. Here is how to figure good values: - TimerOsc = system clock MHz + TimerOsc = selected reference clock MHz tclk_period = desired clock period nanoseconds NominalFreq = 1000 / tclk_period MHz FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0) @@ -114,6 +115,20 @@ Clock Properties: Pulse Per Second (PPS) signal, since this will be offered to the PPS subsystem to synchronize the Linux clock. + Reference clock source is determined by the value, which is holded + in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the + value, which will be directly written in those bits, that is why, + according to reference manual, the next clock sources can be used: + + <0> - external high precision timer reference clock (TSEC_TMR_CLK + input is used for this purpose); + <1> - eTSEC system clock; + <2> - eTSEC1 transmit clock; + <3> - RTC clock input. + + When this attribute is not used, eTSEC system clock will serve as + IEEE 1588 timer reference clock. + Example: ptp_clock@24E00 { @@ -121,6 +136,7 @@ Example: reg = <0x24E00 0xB0>; interrupts = <12 0x8 13 0x8>; interrupt-parent = < &ipic >; + fsl,cksel = <1>; fsl,tclk-period = <10>; fsl,tmr-prsc = <100>; fsl,tmr-add = <0x999999A4>; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index eabcb4b5db6e..e216af356847 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -1,4 +1,4 @@ -* Synopsis Designware PCIe interface +* Synopsys Designware PCIe interface Required properties: - compatible: should contain "snps,dw-pcie" to identify the diff --git a/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt b/Documentation/devicetree/bindings/serial/qca,ar9330-uart.txt index c5e032c85bf9..c5e032c85bf9 100644 --- a/Documentation/devicetree/bindings/tty/serial/qca,ar9330-uart.txt +++ b/Documentation/devicetree/bindings/serial/qca,ar9330-uart.txt diff --git a/Documentation/devicetree/bindings/sound/cs42l73.txt b/Documentation/devicetree/bindings/sound/cs42l73.txt new file mode 100644 index 000000000000..80ae910dbf6c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l73.txt @@ -0,0 +1,22 @@ +CS42L73 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l73" + + - reg : the I2C address of the device for I2C + +Optional properties: + + - reset_gpio : a GPIO spec for the reset pin. + - chgfreq : Charge Pump Frequency values 0x00-0x0F + + +Example: + +codec: cs42l73@4a { + compatible = "cirrus,cs42l73"; + reg = <0x4a>; + reset_gpio = <&gpio 10 0>; + chgfreq = <0x05>; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt new file mode 100644 index 000000000000..865178d5cdf3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt @@ -0,0 +1,42 @@ +* Texas Instruments SoC audio setups with TLV320AIC3X Codec + +Required properties: +- compatible : "ti,da830-evm-audio" : forDM365/DA8xx/OMAPL1x/AM33xx +- ti,model : The user-visible name of this sound complex. +- ti,audio-codec : The phandle of the TLV320AIC3x audio codec +- ti,mcasp-controller : The phandle of the McASP controller +- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec +- ti,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the codec's pins, and the jacks on the board: + + Board connectors: + + * Headphone Jack + * Line Out + * Mic Jack + * Line In + + +Example: + +sound { + compatible = "ti,da830-evm-audio"; + ti,model = "DA830 EVM"; + ti,audio-codec = <&tlv320aic3x>; + ti,mcasp-controller = <&mcasp1>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "MIC3L", "Mic Bias 2V", + "MIC3R", "Mic Bias 2V", + "Mic Bias 2V", "Mic Jack", + "LINE1L", "Line In", + "LINE2L", "Line In", + "LINE1R", "Line In", + "LINE2R", "Line In"; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index 374e145c2ef1..ed785b3f67be 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -4,17 +4,25 @@ Required properties: - compatible : "ti,dm646x-mcasp-audio" : for DM646x platforms "ti,da830-mcasp-audio" : for both DA830 & DA850 platforms - "ti,omap2-mcasp-audio" : for OMAP2 platforms (TI81xx, AM33xx) - -- reg : Should contain McASP registers offset and length -- interrupts : Interrupt number for McASP -- op-mode : I2S/DIT ops mode. -- tdm-slots : Slots for TDM operation. -- num-serializer : Serializers used by McASP. -- serial-dir : A list of serializer pin mode. The list number should be equal - to "num-serializer" parameter. Each entry is a number indication - serializer pin direction. (0 - INACTIVE, 1 - TX, 2 - RX) + "ti,am33xx-mcasp-audio" : for AM33xx platforms (AM33xx, TI81xx) +- reg : Should contain reg specifiers for the entries in the reg-names property. +- reg-names : Should contain: + * "mpu" for the main registers (required). For compatibility with + existing software, it is recommended this is the first entry. + * "dat" for separate data port register access (optional). +- op-mode : I2S/DIT ops mode. 0 for I2S mode. 1 for DIT mode used for S/PDIF, + IEC60958-1, and AES-3 formats. +- tdm-slots : Slots for TDM operation. Indicates number of channels transmitted + or received over one serializer. +- serial-dir : A list of serializer configuration. Each entry is a number + indication for serializer pin direction. + (0 - INACTIVE, 1 - TX, 2 - RX) +- dmas: two element list of DMA controller phandles and DMA request line + ordered pairs. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. The dma + identifiers must be "rx" and "tx". Optional properties: @@ -23,18 +31,23 @@ Optional properties: - rx-num-evt : FIFO levels. - sram-size-playback : size of sram to be allocated during playback - sram-size-capture : size of sram to be allocated during capture +- interrupts : Interrupt numbers for McASP, currently not used by the driver +- interrupt-names : Known interrupt names are "tx" and "rx" +- pinctrl-0: Should specify pin control group used for this controller. +- pinctrl-names: Should contain only one value - "default", for more details + please refer to pinctrl-bindings.txt + Example: mcasp0: mcasp0@1d00000 { compatible = "ti,da830-mcasp-audio"; - #address-cells = <1>; - #size-cells = <0>; reg = <0x100000 0x3000>; - interrupts = <82 83>; + reg-names "mpu"; + interrupts = <82>, <83>; + interrupts-names = "tx", "rx"; op-mode = <0>; /* MCASP_IIS_MODE */ tdm-slots = <2>; - num-serializer = <16>; serial-dir = < 0 0 0 0 /* 0: INACTIVE, 1: TX, 2: RX */ 0 0 0 0 diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index 705a6b156c6c..5e6040c2c2e9 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -24,10 +24,36 @@ Optional properties: 3 - MICBIAS output is connected to AVDD, If this node is not mentioned or if the value is incorrect, then MicBias is powered down. +- AVDD-supply, IOVDD-supply, DRVDD-supply, DVDD-supply : power supplies for the + device as covered in Documentation/devicetree/bindings/regulator/regulator.txt + +CODEC output pins: + * LLOUT + * RLOUT + * MONO_LOUT + * HPLOUT + * HPROUT + * HPLCOM + * HPRCOM + +CODEC input pins: + * MIC3L + * MIC3R + * LINE1L + * LINE2L + * LINE1R + * LINE2R + +The pins can be used in referring sound node's audio-routing property. Example: tlv320aic3x: tlv320aic3x@1b { compatible = "ti,tlv320aic3x"; reg = <0x1b>; + + AVDD-supply = <®ulator>; + IOVDD-supply = <®ulator>; + DRVDD-supply = <®ulator>; + DVDD-supply = <®ulator>; }; diff --git a/Documentation/devicetree/bindings/sound/tpa6130a2.txt b/Documentation/devicetree/bindings/sound/tpa6130a2.txt new file mode 100644 index 000000000000..6dfa740e4b2d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tpa6130a2.txt @@ -0,0 +1,27 @@ +Texas Instruments - tpa6130a2 Codec module + +The tpa6130a2 serial control bus communicates through I2C protocols + +Required properties: + +- compatible - "string" - One of: + "ti,tpa6130a2" - TPA6130A2 + "ti,tpa6140a2" - TPA6140A2 + + +- reg - <int> - I2C slave address + +- Vdd-supply - <phandle> - power supply regulator + +Optional properties: + +- power-gpio - gpio pin to power the device + +Example: + +tpa6130a2: tpa6130a2@60 { + compatible = "ti,tpa6130a2"; + reg = <0x60>; + Vdd-supply = <&vmmc2>; + power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; +}; |
