diff options
| -rw-r--r-- | Documentation/power/00-INDEX | 2 | ||||
| -rw-r--r-- | Documentation/power/opp.txt | 375 | ||||
| -rw-r--r-- | drivers/base/power/Makefile | 1 | ||||
| -rw-r--r-- | drivers/base/power/opp.c | 628 | ||||
| -rw-r--r-- | include/linux/opp.h | 105 | ||||
| -rw-r--r-- | kernel/power/Kconfig | 14 |
6 files changed, 1125 insertions, 0 deletions
diff --git a/Documentation/power/00-INDEX b/Documentation/power/00-INDEX index fb742c213c9e..45e9d4a91284 100644 --- a/Documentation/power/00-INDEX +++ b/Documentation/power/00-INDEX @@ -14,6 +14,8 @@ interface.txt - Power management user interface in /sys/power notifiers.txt - Registering suspend notifiers in device drivers +opp.txt + - Operating Performance Point library pci.txt - How the PCI Subsystem Does Power Management pm_qos_interface.txt diff --git a/Documentation/power/opp.txt b/Documentation/power/opp.txt new file mode 100644 index 000000000000..44d87ad3cea9 --- /dev/null +++ b/Documentation/power/opp.txt @@ -0,0 +1,375 @@ +*=============* +* OPP Library * +*=============* + +(C) 2009-2010 Nishanth Menon <nm@ti.com>, Texas Instruments Incorporated + +Contents +-------- +1. Introduction +2. Initial OPP List Registration +3. OPP Search Functions +4. OPP Availability Control Functions +5. OPP Data Retrieval Functions +6. Cpufreq Table Generation +7. Data Structures + +1. Introduction +=============== +Complex SoCs of today consists of a multiple sub-modules working in conjunction. +In an operational system executing varied use cases, not all modules in the SoC +need to function at their highest performing frequency all the time. To +facilitate this, sub-modules in a SoC are grouped into domains, allowing some +domains to run at lower voltage and frequency while other domains are loaded +more. The set of discrete tuples consisting of frequency and voltage pairs that +the device will support per domain are called Operating Performance Points or +OPPs. + +OPP library provides a set of helper functions to organize and query the OPP +information. The library is located in drivers/base/power/opp.c and the header +is located in include/linux/opp.h. OPP library can be enabled by enabling +CONFIG_PM_OPP from power management menuconfig menu. OPP library depends on +CONFIG_PM as certain SoCs such as Texas Instrument's OMAP framework allows to +optionally boot at a certain OPP without needing cpufreq. + +Typical usage of the OPP library is as follows: +(users) -> registers a set of default OPPs -> (library) +SoC framework -> modifies on required cases certain OPPs -> OPP layer + -> queries to search/retrieve information -> + +OPP layer expects each domain to be represented by a unique device pointer. SoC +framework registers a set of initial OPPs per device with the OPP layer. This +list is expected to be an optimally small number typically around 5 per device. +This initial list contains a set of OPPs that the framework expects to be safely +enabled by default in the system. + +Note on OPP Availability: +------------------------ +As the system proceeds to operate, SoC framework may choose to make certain +OPPs available or not available on each device based on various external +factors. Example usage: Thermal management or other exceptional situations where +SoC framework might choose to disable a higher frequency OPP to safely continue +operations until that OPP could be re-enabled if possible. + +OPP library facilitates this concept in it's implementation. The following +operational functions operate only on available opps: +opp_find_freq_{ceil, floor}, opp_get_voltage, opp_get_freq, opp_get_opp_count +and opp_init_cpufreq_table + +opp_find_freq_exact is meant to be used to find the opp pointer which can then +be used for opp_enable/disable functions to make an opp available as required. + +WARNING: Users of OPP library should refresh their availability count using +get_opp_count if opp_enable/disable functions are invoked for a device, the +exact mechanism to trigger these or the notification mechanism to other +dependent subsystems such as cpufreq are left to the discretion of the SoC +specific framework which uses the OPP library. Similar care needs to be taken +care to refresh the cpufreq table in cases of these operations. + +WARNING on OPP List locking mechanism: +------------------------------------------------- +OPP library uses RCU for exclusivity. RCU allows the query functions to operate +in multiple contexts and this synchronization mechanism is optimal for a read +intensive operations on data structure as the OPP library caters to. + +To ensure that the data retrieved are sane, the users such as SoC framework +should ensure that the section of code operating on OPP queries are locked +using RCU read locks. The opp_find_freq_{exact,ceil,floor}, +opp_get_{voltage, freq, opp_count} fall into this category. + +opp_{add,enable,disable} are updaters which use mutex and implement it's own +RCU locking mechanisms. opp_init_cpufreq_table acts as an updater and uses +mutex to implment RCU updater strategy. These functions should *NOT* be called +under RCU locks and other contexts that prevent blocking functions in RCU or +mutex operations from working. + +2. Initial OPP List Registration +================================ +The SoC implementation calls opp_add function iteratively to add OPPs per +device. It is expected that the SoC framework will register the OPP entries +optimally- typical numbers range to be less than 5. The list generated by +registering the OPPs is maintained by OPP library throughout the device +operation. The SoC framework can subsequently control the availability of the +OPPs dynamically using the opp_enable / disable functions. + +opp_add - Add a new OPP for a specific domain represented by the device pointer. + The OPP is defined using the frequency and voltage. Once added, the OPP + is assumed to be available and control of it's availability can be done + with the opp_enable/disable functions. OPP library internally stores + and manages this information in the opp struct. This function may be + used by SoC framework to define a optimal list as per the demands of + SoC usage environment. + + WARNING: Do not use this function in interrupt context. + + Example: + soc_pm_init() + { + /* Do things */ + r = opp_add(mpu_dev, 1000000, 900000); + if (!r) { + pr_err("%s: unable to register mpu opp(%d)\n", r); + goto no_cpufreq; + } + /* Do cpufreq things */ + no_cpufreq: + /* Do remaining things */ + } + +3. OPP Search Functions +======================= +High level framework such as cpufreq operates on frequencies. To map the +frequency back to the corresponding OPP, OPP library provides handy functions +to search the OPP list that OPP library internally manages. These search +functions return the matching pointer representing the opp if a match is +found, else returns error. These errors are expected to be handled by standard +error checks such as IS_ERR() and appropriate actions taken by the caller. + +opp_find_freq_exact - Search for an OPP based on an *exact* frequency and + availability. This function is especially useful to enable an OPP which + is not available by default. + Example: In a case when SoC framework detects a situation where a + higher frequency could be made available, it can use this function to + find the OPP prior to call the opp_enable to actually make it available. + rcu_read_lock(); + opp = opp_find_freq_exact(dev, 1000000000, false); + rcu_read_unlock(); + /* dont operate on the pointer.. just do a sanity check.. */ + if (IS_ERR(opp)) { + pr_err("frequency not disabled!\n"); + /* trigger appropriate actions.. */ + } else { + opp_enable(dev,1000000000); + } + + NOTE: This is the only search function that operates on OPPs which are + not available. + +opp_find_freq_floor - Search for an available OPP which is *at most* the + provided frequency. This function is useful while searching for a lesser + match OR operating on OPP information in the order of decreasing + frequency. + Example: To find the highest opp for a device: + freq = ULONG_MAX; + rcu_read_lock(); + opp_find_freq_floor(dev, &freq); + rcu_read_unlock(); + +opp_find_freq_ceil - Search for an available OPP which is *at least* the + provided frequency. This function is useful while searching for a + higher match OR operating on OPP information in the order of increasing + frequency. + Example 1: To find the lowest opp for a device: + freq = 0; + rcu_read_lock(); + opp_find_freq_ceil(dev, &freq); + rcu_read_unlock(); + Example 2: A simplified implementation of a SoC cpufreq_driver->target: + soc_cpufreq_target(..) + { + /* Do stuff like policy checks etc. */ + /* Find the best frequency match for the req */ + rcu_read_lock(); + opp = opp_find_freq_ceil(dev, &freq); + rcu_read_unlock(); + if (!IS_ERR(opp)) + soc_switch_to_freq_voltage(freq); + else + /* do something when we cant satisfy the req */ + /* do other stuff */ + } + +4. OPP Availability Control Functions +===================================== +A default OPP list registered with the OPP library may not cater to all possible +situation. The OPP library provides a set of functions to modify the +availability of a OPP within the OPP list. This allows SoC frameworks to have +fine grained dynamic control of which sets of OPPs are operationally available. +These functions are intended to *temporarily* remove an OPP in conditions such +as thermal considerations (e.g. don't use OPPx until the temperature drops). + +WARNING: Do not use these functions in interrupt context. + +opp_enable - Make a OPP available for operation. + Example: Lets say that 1GHz OPP is to be made available only if the + SoC temperature is lower than a certain threshold. The SoC framework + implementation might choose to do something as follows: + if (cur_temp < temp_low_thresh) { + /* Enable 1GHz if it was disabled */ + rcu_read_lock(); + opp = opp_find_freq_exact(dev, 1000000000, false); + rcu_read_unlock(); + /* just error check */ + if (!IS_ERR(opp)) + ret = opp_enable(dev, 1000000000); + else + goto try_something_else; + } + +opp_disable - Make an OPP to be not available for operation + Example: Lets say that 1GHz OPP is to be disabled if the temperature + exceeds a threshold value. The SoC framework implementation might + choose to do something as follows: + if (cur_temp > temp_high_thresh) { + /* Disable 1GHz if it was enabled */ + rcu_read_lock(); + opp = opp_find_freq_exact(dev, 1000000000, true); + rcu_read_unlock(); + /* just error check */ + if (!IS_ERR(opp)) + ret = opp_disable(dev, 1000000000); + else + goto try_something_else; + } + +5. OPP Data Retrieval Functions +=============================== +Since OPP library abstracts away the OPP information, a set of functions to pull +information from the OPP structure is necessary. Once an OPP pointer is +retrieved using the search functions, the following functions can be used by SoC +framework to retrieve the information represented inside the OPP layer. + +opp_get_voltage - Retrieve the voltage represented by the opp pointer. + Example: At a cpufreq transition to a different frequency, SoC + framework requires to set the voltage represented by the OPP using + the regulator framework to the Power Management chip providing the + voltage. + soc_switch_to_freq_voltage(freq) + { + /* do things */ + rcu_read_lock(); + opp = opp_find_freq_ceil(dev, &freq); + v = opp_get_voltage(opp); + rcu_read_unlock(); + if (v) + regulator_set_voltage(.., v); + /* do other things */ + } + +opp_get_freq - Retrieve the freq represented by the opp pointer. + Example: Lets say the SoC framework uses a couple of helper functions + we could pass opp pointers instead of doing additional parameters to + handle quiet a bit of data parameters. + soc_cpufreq_target(..) + { + /* do things.. */ + max_freq = ULONG_MAX; + rcu_read_lock(); + max_opp = opp_find_freq_floor(dev,&max_freq); + requested_opp = opp_find_freq_ceil(dev,&freq); + if (!IS_ERR(max_opp) && !IS_ERR(requested_opp)) + r = soc_test_validity(max_opp, requested_opp); + rcu_read_unlock(); + /* do other things */ + } + soc_test_validity(..) + { + if(opp_get_voltage(max_opp) < opp_get_voltage(requested_opp)) + return -EINVAL; + if(opp_get_freq(max_opp) < opp_get_freq(requested_opp)) + return -EINVAL; + /* do things.. */ + } + +opp_get_opp_count - Retrieve the number of available opps for a device + Example: Lets say a co-processor in the SoC needs to know the available + frequencies in a table, the main processor can notify as following: + soc_notify_coproc_available_frequencies() + { + /* Do things */ + rcu_read_lock(); + num_available = opp_get_opp_count(dev); + speeds = kzalloc(sizeof(u32) * num_available, GFP_KERNEL); + /* populate the table in increasing order */ + freq = 0; + while (!IS_ERR(opp = opp_find_freq_ceil(dev, &freq))) { + speeds[i] = freq; + freq++; + i++; + } + rcu_read_unlock(); + + soc_notify_coproc(AVAILABLE_FREQs, speeds, num_available); + /* Do other things */ + } + +6. Cpufreq Table Generation +=========================== +opp_init_cpufreq_table - cpufreq framework typically is initialized with + cpufreq_frequency_table_cpuinfo which is provided with the list of + frequencies that are available for operation. This function provides + a ready to use conversion routine to translate the OPP layer's internal + information about the available frequencies into a format readily + providable to cpufreq. + + WARNING: Do not use this function in interrupt context. + + Example: + soc_pm_init() + { + /* Do things */ + r = opp_init_cpufreq_table(dev, &freq_table); + if (!r) + cpufreq_frequency_table_cpuinfo(policy, freq_table); + /* Do other things */ + } + + NOTE: This function is available only if CONFIG_CPU_FREQ is enabled in + addition to CONFIG_PM as power management feature is required to + dynamically scale voltage and frequency in a system. + +7. Data Structures +================== +Typically an SoC contains multiple voltage domains which are variable. Each +domain is represented by a device pointer. The relationship to OPP can be +represented as follows: +SoC + |- device 1 + | |- opp 1 (availability, freq, voltage) + | |- opp 2 .. + ... ... + | `- opp n .. + |- device 2 + ... + `- device m + +OPP library maintains a internal list that the SoC framework populates and +accessed by various functions as described above. However, the structures +representing the actual OPPs and domains are internal to the OPP library itself +to allow for suitable abstraction reusable across systems. + +struct opp - The internal data structure of OPP library which is used to + represent an OPP. In addition to the freq, voltage, availability + information, it also contains internal book keeping information required + for the OPP library to operate on. Pointer to this structure is + provided back to the users such as SoC framework to be used as a + identifier for OPP in the interactions with OPP layer. + + WARNING: The struct opp pointer should not be parsed or modified by the + users. The defaults of for an instance is populated by opp_add, but the + availability of the OPP can be modified by opp_enable/disable functions. + +struct device - This is used to identify a domain to the OPP layer. The + nature of the device and it's implementation is left to the user of + OPP library such as the SoC framework. + +Overall, in a simplistic view, the data structure operations is represented as +following: + +Initialization / modification: + +-----+ /- opp_enable +opp_add --> | opp | <------- + | +-----+ \- opp_disable + \-------> domain_info(device) + +Search functions: + /-- opp_find_freq_ceil ---\ +-----+ +domain_info<---- opp_find_freq_exact -----> | opp | + \-- opp_find_freq_floor ---/ +-----+ + +Retrieval functions: ++-----+ /- opp_get_voltage +| opp | <--- ++-----+ \- opp_get_freq + +domain_info <- opp_get_opp_count diff --git a/drivers/base/power/Makefile b/drivers/base/power/Makefile index cbccf9a3cee4..abe46edfe5b4 100644 --- a/drivers/base/power/Makefile +++ b/drivers/base/power/Makefile @@ -3,6 +3,7 @@ obj-$(CONFIG_PM_SLEEP) += main.o wakeup.o obj-$(CONFIG_PM_RUNTIME) += runtime.o obj-$(CONFIG_PM_OPS) += generic_ops.o obj-$(CONFIG_PM_TRACE_RTC) += trace.o +obj-$(CONFIG_PM_OPP) += opp.o ccflags-$(CONFIG_DEBUG_DRIVER) := -DDEBUG ccflags-$(CONFIG_PM_VERBOSE) += -DDEBUG diff --git a/drivers/base/power/opp.c b/drivers/base/power/opp.c new file mode 100644 index 000000000000..2bb9b4cf59d7 --- /dev/null +++ b/drivers/base/power/opp.c @@ -0,0 +1,628 @@ +/* + * Generic OPP Interface + * + * Copyright (C) 2009-2010 Texas Instruments Incorporated. + * Nishanth Menon + * Romit Dasgupta + * Kevin Hilman + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/cpufreq.h> +#include <linux/list.h> +#include <linux/rculist.h> +#include <linux/rcupdate.h> +#include <linux/opp.h> + +/* + * Internal data structure organization with the OPP layer library is as + * follows: + * dev_opp_list (root) + * |- device 1 (represents voltage domain 1) + * | |- opp 1 (availability, freq, voltage) + * | |- opp 2 .. + * ... ... + * | `- opp n .. + * |- device 2 (represents the next voltage domain) + * ... + * `- device m (represents mth voltage domain) + * device 1, 2.. are represented by dev_opp structure while each opp + * is represented by the opp structure. + */ + +/** + * struct opp - Generic OPP description structure + * @node: opp list node. The nodes are maintained throughout the lifetime + * of boot. It is expected only an optimal set of OPPs are + * added to the library by the SoC framework. + * RCU usage: opp list is traversed with RCU locks. node + * modification is possible realtime, hence the modifications + * are protected by the dev_opp_list_lock for integrity. + * IMPORTANT: the opp nodes should be maintained in increasing + * order. + * @available: true/false - marks if this OPP as available or not + * @rate: Frequency in hertz + * @u_volt: Nominal voltage in microvolts corresponding to this OPP + * @dev_opp: points back to the device_opp struct this opp belongs to + * + * This structure stores the OPP information for a given device. + */ +struct opp { + struct list_head node; + + bool available; + unsigned long rate; + unsigned long u_volt; + + struct device_opp *dev_opp; +}; + +/** + * struct device_opp - Device opp structure + * @node: list node - contains the devices with OPPs that + * have been registered. Nodes once added are not modified in this + * list. + * RCU usage: nodes are not modified in the list of device_opp, + * however addition is possible and is secured by dev_opp_list_lock + * @dev: device pointer + * @opp_list: list of opps + * + * This is an internal data structure maintaining the link to opps attached to + * a device. This structure is not meant to be shared to users as it is + * meant for book keeping and private to OPP library + */ +struct device_opp { + struct list_head node; + + struct device *dev; + struct list_head opp_list; +}; + +/* + * The root of the list of all devices. All device_opp structures branch off + * from here, with each device_opp containing the list of opp it supports in + * various states of availability. + */ +static LIST_HEAD(dev_opp_list); +/* Lock to allow exclusive modification to the device and opp lists */ +static DEFINE_MUTEX(dev_opp_list_lock); + +/** + * find_device_opp() - find device_opp struct using device pointer + * @dev: device pointer used to lookup device OPPs + * + * Search list of device OPPs for one containing matching device. Does a RCU + * reader operation to grab the pointer needed. + * + * Returns pointer to 'struct device_opp' if found, otherwise -ENODEV or + * -EINVAL based on type of error. + * + * Locking: This function must be called under rcu_read_lock(). device_opp + * is a RCU protected pointer. This means that device_opp is valid as long + * as we are under RCU lock. + */ +static struct device_opp *find_device_opp(struct device *dev) +{ + struct device_opp *tmp_dev_opp, *dev_opp = ERR_PTR(-ENODEV); + + if (unlikely(IS_ERR_OR_NULL(dev))) { + pr_err("%s: Invalid parameters\n", __func__); + return ERR_PTR(-EINVAL); + } + + list_for_each_entry_rcu(tmp_dev_opp, &dev_opp_list, node) { + if (tmp_dev_opp->dev == dev) { + dev_opp = tmp_dev_opp; + break; + } + } + + return dev_opp; +} + +/** + * opp_get_voltage() - Gets the voltage corresponding to an available opp + * @opp: opp for which voltage has to be returned for + * + * Return voltage in micro volt corresponding to the opp, else + * return 0 + * + * Locking: This function must be called under rcu_read_lock(). opp is a rcu + * protected pointer. This means that opp which could have been fetched by + * opp_find_freq_{exact,ceil,floor} functions is valid as long as we are + * under RCU lock. The pointer returned by the opp_find_freq family must be + * used in the same section as the usage of this function with the pointer + * prior to unlocking with rcu_read_unlock() to maintain the integrity of the + * pointer. + */ +unsigned long opp_get_voltage(struct opp *opp) +{ + struct opp *tmp_opp; + unsigned long v = 0; + + tmp_opp = rcu_dereference(opp); + if (unlikely(IS_ERR_OR_NULL(tmp_opp)) || !tmp_opp->available) + pr_err("%s: Invalid parameters\n", __func__); + else + v = tmp_opp->u_volt; + + return v; +} + +/** + * opp_get_freq() - Gets the frequency corresponding to an available opp + * @opp: opp for which frequency has to be returned for + * + * Return frequency in hertz corresponding to the opp, else + * return 0 + * + * Locking: This function must be called under rcu_read_lock(). opp is a rcu + * protected pointer. This means that opp which could have been fetched by + * opp_find_freq_{exact,ceil,floor} functions is valid as long as we are + * under RCU lock. The pointer returned by the opp_find_freq family must be + * used in the same section as the usage of this function with the pointer + * prior to unlocking with rcu_read_unlock() to maintain the integrity of the + * pointer. + */ +unsigned long opp_get_freq(struct opp *opp) +{ + struct opp *tmp_opp; + unsigned long f = 0; + + tmp_opp = rcu_dereference(opp); + if (unlikely(IS_ERR_OR_NULL(tmp_opp)) || !tmp_opp->available) + pr_err("%s: Invalid parameters\n", __func__); + else + f = tmp_opp->rate; + + return f; +} + +/** + * opp_get_opp_count() - Get number of opps available in the opp list + * @dev: device for which we do this operation + * + * This function returns the number of available opps if there are any, + * else returns 0 if none or the corresponding error value. + * + * Locking: This function must be called under rcu_read_lock(). This function + * internally references two RCU protected structures: device_opp and opp which + * are safe as long as we are under a common RCU locked section. + */ +int opp_get_opp_count(struct device *dev) +{ + struct device_opp *dev_opp; + struct opp *temp_opp; + int count = 0; + + dev_opp = find_device_opp(dev); + if (IS_ERR(dev_opp)) { + int r = PTR_ERR(dev_opp); + dev_err(dev, "%s: device OPP not found (%d)\n", __func__, r); + return r; + } + + list_for_each_entry_rcu(temp_opp, &dev_opp->opp_list, node) { + if (temp_opp->available) + count++; + } + + return count; +} + +/** + * opp_find_freq_exact() - search for an exact frequency + * @dev: device for which we do this operation + * @freq: frequency to search for + * @is_available: true/false - match for available opp + * + * Searches for exact match in the opp list and returns pointer to the matching + * opp if found, else returns ERR_PTR in case of error and should be handled + * using IS_ERR. + * + * Note: available is a modifier for the search. if available=true, then the + * match is for exact matching frequency and is available in the stored OPP + * table. if false, the match is for exact frequency which is not available. + * + * This provides a mechanism to enable an opp which is not available currently + * or the opposite as well. + * + * Locking: This function must be called under rcu_read_lock(). opp is a rcu + * protected pointer. The reason for the same is that the opp pointer which is + * returned will remain valid for use with opp_get_{voltage, freq} only while + * under the locked area. The pointer returned must be used prior to unlocking + * with rcu_read_unlock() to maintain the integrity of the pointer. + */ +struct opp *opp_find_freq_exact(struct device *dev, unsigned long freq, + bool available) +{ + struct device_opp *dev_opp; + struct opp *temp_opp, *opp = ERR_PTR(-ENODEV); + + dev_opp = find_device_opp(dev); + if (IS_ERR(dev_opp)) { + int r = PTR_ERR(dev_opp); + dev_err(dev, "%s: device OPP not found (%d)\n", __func__, r); + return ERR_PTR(r); + } + + list_for_each_entry_rcu(temp_opp, &dev_opp->opp_list, node) { + if (temp_opp->available == available && + temp_opp->rate == freq) { + opp = temp_opp; + break; + } + } + + return opp; +} + +/** + * opp_find_freq_ceil() - Search for an rounded ceil freq + * @dev: device for which we do this operation + * @freq: Start frequency + * + * Search for the matching ceil *available* OPP from a starting freq + * for a device. + * + * Returns matching *opp and refreshes *freq accordingly, else returns + * ERR_PTR in case of error and should be handled using IS_ERR. + * + * Locking: This function must be called under rcu_read_lock(). opp is a rcu + * protected pointer. The reason for the same is that the opp pointer which is + * returned will remain valid for use with opp_get_{voltage, freq} only while + * under the locked area. The pointer returned must be used prior to unlocking + * with rcu_read_unlock() to maintain the integrity of the pointer. + */ +struct opp *opp_find_freq_ceil(struct device *dev, unsigned long *freq) +{ + struct device_opp *dev_opp; + struct opp *temp_opp, *opp = ERR_PTR(-ENODEV); + + if (!dev || !freq) { + dev_err(dev, "%s: Invalid argument freq=%p\n", __func__, freq); + return ERR_PTR(-EINVAL); + } + + dev_opp = find_device_opp(dev); + if (IS_ERR(dev_opp)) + return opp; + + list_for_each_entry_rcu(temp_opp, &dev_opp->opp_list, node) { + if (temp_opp->available && temp_opp->rate >= *freq) { + opp = temp_opp; + *freq = opp->rate; + break; + } + } + + return opp; +} + +/** + * opp_find_freq_floor() - Search for a rounded floor freq + * @dev: device for which we do this operation + * @freq: Start frequency + * + * Search for the matching floor *available* OPP from a starting freq + * for a device. + * + * Returns matching *opp and refreshes *freq accordingly, else returns + * ERR_PTR in case of error and should be handled using IS_ERR. + * + * Locking: This function must be called under rcu_read_lock(). opp is a rcu + * protected pointer. The reason for the same is that the opp pointer which is + * returned will remain valid for use with opp_get_{voltage, freq} only while + * under the locked area. The pointer returned must be used prior to unlocking + * with rcu_read_unlock() to maintain the integrity of the pointer. + */ +struct opp *opp_find_freq_floor(struct device *dev, unsigned long *freq) +{ + struct device_opp *dev_opp; + struct opp *temp_opp, *opp = ERR_PTR(-ENODEV); + + if (!dev || !freq) { + dev_err(dev, "%s: Invalid argument freq=%p\n", __func__, freq); + return ERR_PTR(-EINVAL); + } + + dev_opp = find_device_opp(dev); + if (IS_ERR(dev_opp)) + return opp; + + list_for_each_entry_rcu(temp_opp, &dev_opp->opp_list, node) { + if (temp_opp->available) { + /* go to the next node, before choosing prev */ + if (temp_opp->rate > *freq) + break; + else + opp = temp_opp; + } + } + if (!IS_ERR(opp)) + *freq = opp->rate; + + return opp; +} + +/** + * opp_add() - Add an OPP table from a table definitions + * @dev: device for which we do this operation + * @freq: Frequency in Hz for this OPP + * @u_volt: Voltage in uVolts for this OPP + * + * This function adds an opp definition to the opp list and returns status. + * The opp is made available by default and it can be controlled using + * opp_enable/disable functions. + * + * Locking: The internal device_opp and opp structures are RCU protected. + * Hence this function internally uses RCU updater strategy with mutex locks + * to keep the integrity of the internal data structures. Callers should ensure + * that this function is *NOT* called under RCU protection or in contexts where + * mutex cannot be locked. + */ +int opp_add(struct device *dev, unsigned long freq, unsigned long u_volt) +{ + struct device_opp *dev_opp = NULL; + struct opp *opp, *new_opp; + struct list_head *head; + + /* allocate new OPP node */ + new_opp = kzalloc(sizeof(struct opp), GFP_KERNEL); + if (!new_opp) { + dev_warn(dev, "%s: Unable to create new OPP node\n", __func__); + return -ENOMEM; + } + + /* Hold our list modification lock here */ + mutex_lock(&dev_opp_list_lock); + + /* Check for existing list for 'dev' */ + dev_opp = find_device_opp(dev); + if (IS_ERR(dev_opp)) { + /* + * Allocate a new device OPP table. In the infrequent case + * where a new device is needed to be added, we pay this + * penalty. + */ + dev_opp = kzalloc(sizeof(struct device_opp), GFP_KERNEL); + if (!dev_opp) { + mutex_unlock(&dev_opp_list_lock); + kfree(new_opp); + dev_warn(dev, + "%s: Unable to create device OPP structure\n", + __func__); + return -ENOMEM; + } + + dev_opp->dev = dev; + INIT_LIST_HEAD(&dev_opp->opp_list); + + /* Secure the device list modification */ + list_add_rcu(&dev_opp->node, &dev_opp_list); + } + + /* populate the opp table */ + new_opp->dev_opp = dev_opp; + new_opp->rate = freq; + new_opp->u_volt = u_volt; + new_opp->available = true; + + /* Insert new OPP in order of increasing frequency */ + head = &dev_opp->opp_list; + list_for_each_entry_rcu(opp, &dev_opp->opp_list, node) { + if (new_opp->rate < opp->rate) + break; + else + head = &opp->node; + } + + list_add_rcu(&new_opp->node, head); + mutex_unlock(&dev_opp_list_lock); + + return 0; +} + +/** + * opp_set_availability() - helper to set the availability of an opp + * @dev: device for which we do this operation + * @freq: OPP frequency to modify availability + * @availability_req: availability status requested for this opp + * + * Set the availability of an OPP with an RCU operation, opp_{enable,disable} + * share a common logic which is isolated here. + * + * Returns -EINVAL for bad pointers, -ENOMEM if no memory available for the + * copy operation, returns 0 if no modifcation was done OR modification was + * successful. + * + * Locking: The internal device_opp and opp structures are RCU protected. + * Hence this function internally uses RCU updater strategy with mutex locks to + * keep the integrity of the internal data structures. Callers should ensure + * that this function is *NOT* called under RCU protection or in contexts where + * mutex locking or synchronize_rcu() blocking calls cannot be used. + */ +static int opp_set_availability(struct device *dev, unsigned long freq, + bool availability_req) +{ + struct device_opp *tmp_dev_opp, *dev_opp = NULL; + struct opp *new_opp, *tmp_opp, *opp = ERR_PTR(-ENODEV); + int r = 0; + + /* keep the node allocated */ + new_opp = kmalloc(sizeof(struct opp), GFP_KERNEL); + if (!new_opp) { + dev_warn(dev, "%s: Unable to create OPP\n", __func__); + return -ENOMEM; + } + + mutex_lock(&dev_opp_list_lock); + + /* Find the device_opp */ + list_for_each_entry(tmp_dev_opp, &dev_opp_list, node) { + if (dev == tmp_dev_opp->dev) { + dev_opp = tmp_dev_opp; + break; + } + } + if (IS_ERR(dev_opp)) { + r = PTR_ERR(dev_opp); + dev_warn(dev, "%s: Device OPP not found (%d)\n", __func__, r); + goto unlock; + } + + /* Do we have the frequency? */ + list_for_each_entry(tmp_opp, &dev_opp->opp_list, node) { + if (tmp_opp->rate == freq) { + opp = tmp_opp; + break; + } + } + if (IS_ERR(opp)) { + r = PTR_ERR(opp); + goto unlock; + } + + /* Is update really needed? */ + if (opp->available == availability_req) + goto unlock; + /* copy the old data over */ + *new_opp = *opp; + + /* plug in new node */ + new_opp->available = availability_req; + + list_replace_rcu(&opp->node, &new_opp->node); + mutex_unlock(&dev_opp_list_lock); + synchronize_rcu(); + + /* clean up old opp */ + new_opp = opp; + goto out; + +unlock: + mutex_unlock(&dev_opp_list_lock); +out: + kfree(new_opp); + return r; +} + +/** + * opp_enable() - Enable a specific OPP + * @dev: device for which we do this operation + * @freq: OPP frequency to enable + * + * Enables a provided opp. If the operation is valid, this returns 0, else the + * corresponding error value. It is meant to be used for users an OPP available + * after being temporarily made unavailable with opp_disable. + * + * Locking: The internal device_opp and opp structures are RCU protected. + * Hence this function indirectly uses RCU and mutex locks to keep the + * integrity of the internal data structures. Callers should ensure that + * this function is *NOT* called under RCU protection or in contexts where + * mutex locking or synchronize_rcu() blocking calls cannot be used. + */ +int opp_enable(struct device *dev, unsigned long freq) +{ + return opp_set_availability(dev, freq, true); +} + +/** + * opp_disable() - Disable a specific OPP + * @dev: device for which we do this operation + * @freq: OPP frequency to disable + * + * Disables a provided opp. If the operation is valid, this returns + * 0, else the corresponding error value. It is meant to be a temporary + * control by users to make this OPP not available until the circumstances are + * right to make it available again (with a call to opp_enable). + * + * Locking: The internal device_opp and opp structures are RCU protected. + * Hence this function indirectly uses RCU and mutex locks to keep the + * integrity of the internal data structures. Callers should ensure that + * this function is *NOT* called under RCU protection or in contexts where + * mutex locking or synchronize_rcu() blocking calls cannot be used. + */ +int opp_disable(struct device *dev, unsigned long freq) +{ + return opp_set_availability(dev, freq, false); +} + +#ifdef CONFIG_CPU_FREQ +/** + * opp_init_cpufreq_table() - create a cpufreq table for a device + * @dev: device for which we do this operation + * @table: Cpufreq table returned back to caller + * + * Generate a cpufreq table for a provided device- this assumes that the + * opp list is already initialized and ready for usage. + * + * This function allocates required memory for the cpufreq table. It is + * expected that the caller does the required maintenance such as freeing + * the table as required. + * + * Returns -EINVAL for bad pointers, -ENODEV if the device is not found, -ENOMEM + * if no memory available for the operation (table is not populated), returns 0 + * if successful and table is populated. + * + * WARNING: It is important for the callers to ensure refreshing their copy of + * the table if any of the mentioned functions have been invoked in the interim. + * + * Locking: The internal device_opp and opp structures are RCU protected. + * To simplify the logic, we pretend we are updater and hold relevant mutex here + * Callers should ensure that this function is *NOT* called under RCU protection + * or in contexts where mutex locking cannot be used. + */ +int opp_init_cpufreq_table(struct device *dev, + struct cpufreq_frequency_table **table) +{ + struct device_opp *dev_opp; + struct opp *opp; + struct cpufreq_frequency_table *freq_table; + int i = 0; + + /* Pretend as if I am an updater */ + mutex_lock(&dev_opp_list_lock); + + dev_opp = find_device_opp(dev); + if (IS_ERR(dev_opp)) { + int r = PTR_ERR(dev_opp); + mutex_unlock(&dev_opp_list_lock); + dev_err(dev, "%s: Device OPP not found (%d)\n", __func__, r); + return r; + } + + freq_table = kzalloc(sizeof(struct cpufreq_frequency_table) * + (opp_get_opp_count(dev) + 1), GFP_KERNEL); + if (!freq_table) { + mutex_unlock(&dev_opp_list_lock); + dev_warn(dev, "%s: Unable to allocate frequency table\n", + __func__); + return -ENOMEM; + } + + list_for_each_entry(opp, &dev_opp->opp_list, node) { + if (opp->available) { + freq_table[i].index = i; + freq_table[i].frequency = opp->rate / 1000; + i++; + } + } + mutex_unlock(&dev_opp_list_lock); + + freq_table[i].index = i; + freq_table[i].frequency = CPUFREQ_TABLE_END; + + *table = &freq_table[0]; + + return 0; +} +#endif /* CONFIG_CPU_FREQ */ diff --git a/include/linux/opp.h b/include/linux/opp.h new file mode 100644 index 000000000000..5449945d589f --- /dev/null +++ b/include/linux/opp.h @@ -0,0 +1,105 @@ +/* + * Generic OPP Interface + * + * Copyright (C) 2009-2010 Texas Instruments Incorporated. + * Nishanth Menon + * Romit Dasgupta + * Kevin Hilman + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __LINUX_OPP_H__ +#define __LINUX_OPP_H__ + +#include <linux/err.h> +#include <linux/cpufreq.h> + +struct opp; + +#if defined(CONFIG_PM_OPP) + +unsigned long opp_get_voltage(struct opp *opp); + +unsigned long opp_get_freq(struct opp *opp); + +int opp_get_opp_count(struct device *dev); + +struct opp *opp_find_freq_exact(struct device *dev, unsigned long freq, + bool available); + +struct opp *opp_find_freq_floor(struct device *dev, unsigned long *freq); + +struct opp *opp_find_freq_ceil(struct device *dev, unsigned long *freq); + +int opp_add(struct device *dev, unsigned long freq, unsigned long u_volt); + +int opp_enable(struct device *dev, unsigned long freq); + +int opp_disable(struct device *dev, unsigned long freq); + +#else +static inline unsigned long opp_get_voltage(struct opp *opp) +{ + return 0; +} + +static inline unsigned long opp_get_freq(struct opp *opp) +{ + return 0; +} + +static inline int opp_get_opp_count(struct device *dev) +{ + return 0; +} + +static inline struct opp *opp_find_freq_exact(struct device *dev, + unsigned long freq, bool available) +{ + return ERR_PTR(-EINVAL); +} + +static inline struct opp *opp_find_freq_floor(struct device *dev, + unsigned long *freq) +{ + return ERR_PTR(-EINVAL); +} + +static inline struct opp *opp_find_freq_ceil(struct device *dev, + unsigned long *freq) +{ + return ERR_PTR(-EINVAL); +} + +static inline int opp_add(struct device *dev, unsigned long freq, + unsigned long u_volt) +{ + return -EINVAL; +} + +static inline int opp_enable(struct device *dev, unsigned long freq) +{ + return 0; +} + +static inline int opp_disable(struct device *dev, unsigned long freq) +{ + return 0; +} +#endif /* CONFIG_PM */ + +#if defined(CONFIG_CPU_FREQ) && defined(CONFIG_PM_OPP) +int opp_init_cpufreq_table(struct device *dev, + struct cpufreq_frequency_table **table); +#else +static inline int opp_init_cpufreq_table(struct device *dev, + struct cpufreq_frequency_table **table) +{ + return -EINVAL; +} +#endif /* CONFIG_CPU_FREQ */ + +#endif /* __LINUX_OPP_H__ */ diff --git a/kernel/power/Kconfig b/kernel/power/Kconfig index e45894c696ee..29bff6117abc 100644 --- a/kernel/power/Kconfig +++ b/kernel/power/Kconfig @@ -245,3 +245,17 @@ config PM_OPS bool depends on PM_SLEEP || PM_RUNTIME default y + +config PM_OPP + bool "Operating Performance Point (OPP) Layer library" + depends on PM + ---help--- + SOCs have a standard set of tuples consisting of frequency and + voltage pairs that the device will support per voltage domain. This + is called Operating Performance Point or OPP. The actual definitions + of OPP varies over silicon within the same family of devices. + + OPP layer organizes the data internally using device pointers + representing individual voltage domains and provides SOC + implementations a ready to use framework to manage OPPs. + For more information, read <file:Documentation/power/opp.txt> |
