diff options
| -rw-r--r-- | Documentation/devicetree/bindings/net/micrel.txt | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/phy.txt | 3 | ||||
| -rw-r--r-- | drivers/net/phy/micrel.c | 125 |
3 files changed, 93 insertions, 37 deletions
diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt index e1d99b95c4ec..30062fae5623 100644 --- a/Documentation/devicetree/bindings/net/micrel.txt +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -14,6 +14,8 @@ Optional properties: KSZ8021: register 0x1f, bits 5..4 KSZ8031: register 0x1f, bits 5..4 KSZ8051: register 0x1f, bits 5..4 + KSZ8081: register 0x1f, bits 5..4 + KSZ8091: register 0x1f, bits 5..4 See the respective PHY datasheet for the mode values. diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 5b8c58903077..40831fbaff72 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -19,7 +19,6 @@ Optional Properties: specifications. If neither of these are specified, the default is to assume clause 22. The compatible list may also contain other elements. -- max-speed: Maximum PHY supported speed (10, 100, 1000...) If the phy's identifier is known then the list may contain an entry of the form: "ethernet-phy-idAAAA.BBBB" where @@ -29,6 +28,8 @@ Optional Properties: 4 hex digits. This is the chip vendor OUI bits 19:24, followed by 10 bits of a vendor specific ID. +- max-speed: Maximum PHY supported speed (10, 100, 1000...) + Example: ethernet-phy@0 { diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index bcc6c0ea75fa..30e894d6ffbd 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -30,30 +30,34 @@ /* Operation Mode Strap Override */ #define MII_KSZPHY_OMSO 0x16 -#define KSZPHY_OMSO_B_CAST_OFF (1 << 9) -#define KSZPHY_OMSO_RMII_OVERRIDE (1 << 1) -#define KSZPHY_OMSO_MII_OVERRIDE (1 << 0) +#define KSZPHY_OMSO_B_CAST_OFF BIT(9) +#define KSZPHY_OMSO_RMII_OVERRIDE BIT(1) +#define KSZPHY_OMSO_MII_OVERRIDE BIT(0) /* general Interrupt control/status reg in vendor specific block. */ #define MII_KSZPHY_INTCS 0x1B -#define KSZPHY_INTCS_JABBER (1 << 15) -#define KSZPHY_INTCS_RECEIVE_ERR (1 << 14) -#define KSZPHY_INTCS_PAGE_RECEIVE (1 << 13) -#define KSZPHY_INTCS_PARELLEL (1 << 12) -#define KSZPHY_INTCS_LINK_PARTNER_ACK (1 << 11) -#define KSZPHY_INTCS_LINK_DOWN (1 << 10) -#define KSZPHY_INTCS_REMOTE_FAULT (1 << 9) -#define KSZPHY_INTCS_LINK_UP (1 << 8) +#define KSZPHY_INTCS_JABBER BIT(15) +#define KSZPHY_INTCS_RECEIVE_ERR BIT(14) +#define KSZPHY_INTCS_PAGE_RECEIVE BIT(13) +#define KSZPHY_INTCS_PARELLEL BIT(12) +#define KSZPHY_INTCS_LINK_PARTNER_ACK BIT(11) +#define KSZPHY_INTCS_LINK_DOWN BIT(10) +#define KSZPHY_INTCS_REMOTE_FAULT BIT(9) +#define KSZPHY_INTCS_LINK_UP BIT(8) #define KSZPHY_INTCS_ALL (KSZPHY_INTCS_LINK_UP |\ KSZPHY_INTCS_LINK_DOWN) -/* general PHY control reg in vendor specific block. */ -#define MII_KSZPHY_CTRL 0x1F +/* PHY Control 1 */ +#define MII_KSZPHY_CTRL_1 0x1e + +/* PHY Control 2 / PHY Control (if no PHY Control 1) */ +#define MII_KSZPHY_CTRL_2 0x1f +#define MII_KSZPHY_CTRL MII_KSZPHY_CTRL_2 /* bitmap of PHY register to set interrupt mode */ -#define KSZPHY_CTRL_INT_ACTIVE_HIGH (1 << 9) -#define KSZ9021_CTRL_INT_ACTIVE_HIGH (1 << 14) -#define KS8737_CTRL_INT_ACTIVE_HIGH (1 << 14) -#define KSZ8051_RMII_50MHZ_CLK (1 << 7) +#define KSZPHY_CTRL_INT_ACTIVE_HIGH BIT(9) +#define KSZ9021_CTRL_INT_ACTIVE_HIGH BIT(14) +#define KS8737_CTRL_INT_ACTIVE_HIGH BIT(14) +#define KSZ8051_RMII_50MHZ_CLK BIT(7) /* Write/read to/from extended registers */ #define MII_KSZPHY_EXTREG 0x0b @@ -122,6 +126,8 @@ static int kszphy_config_intr(struct phy_device *phydev) /* set the interrupt pin active low */ temp = phy_read(phydev, MII_KSZPHY_CTRL); + if (temp < 0) + return temp; temp &= ~KSZPHY_CTRL_INT_ACTIVE_HIGH; phy_write(phydev, MII_KSZPHY_CTRL, temp); rc = kszphy_set_interrupt(phydev); @@ -134,6 +140,8 @@ static int ksz9021_config_intr(struct phy_device *phydev) /* set the interrupt pin active low */ temp = phy_read(phydev, MII_KSZPHY_CTRL); + if (temp < 0) + return temp; temp &= ~KSZ9021_CTRL_INT_ACTIVE_HIGH; phy_write(phydev, MII_KSZPHY_CTRL, temp); rc = kszphy_set_interrupt(phydev); @@ -146,19 +154,20 @@ static int ks8737_config_intr(struct phy_device *phydev) /* set the interrupt pin active low */ temp = phy_read(phydev, MII_KSZPHY_CTRL); + if (temp < 0) + return temp; temp &= ~KS8737_CTRL_INT_ACTIVE_HIGH; phy_write(phydev, MII_KSZPHY_CTRL, temp); rc = kszphy_set_interrupt(phydev); return rc < 0 ? rc : 0; } -static int kszphy_setup_led(struct phy_device *phydev, - unsigned int reg, unsigned int shift) +static int kszphy_setup_led(struct phy_device *phydev, u32 reg) { struct device *dev = &phydev->dev; struct device_node *of_node = dev->of_node; - int rc, temp; + int rc, temp, shift; u32 val; if (!of_node && dev->parent->of_node) @@ -167,15 +176,55 @@ static int kszphy_setup_led(struct phy_device *phydev, if (of_property_read_u32(of_node, "micrel,led-mode", &val)) return 0; + if (val > 3) { + dev_err(&phydev->dev, "invalid led mode: 0x%02x\n", val); + return -EINVAL; + } + + switch (reg) { + case MII_KSZPHY_CTRL_1: + shift = 14; + break; + case MII_KSZPHY_CTRL_2: + shift = 4; + break; + default: + return -EINVAL; + } + temp = phy_read(phydev, reg); - if (temp < 0) - return temp; + if (temp < 0) { + rc = temp; + goto out; + } temp &= ~(3 << shift); temp |= val << shift; rc = phy_write(phydev, reg, temp); +out: + if (rc < 0) + dev_err(&phydev->dev, "failed to set led mode\n"); - return rc < 0 ? rc : 0; + return rc; +} + +/* Disable PHY address 0 as the broadcast address, so that it can be used as a + * unique (non-broadcast) address on a shared bus. + */ +static int kszphy_broadcast_disable(struct phy_device *phydev) +{ + int ret; + + ret = phy_read(phydev, MII_KSZPHY_OMSO); + if (ret < 0) + goto out; + + ret = phy_write(phydev, MII_KSZPHY_OMSO, ret | KSZPHY_OMSO_B_CAST_OFF); +out: + if (ret) + dev_err(&phydev->dev, "failed to disable broadcast address\n"); + + return ret; } static int kszphy_config_init(struct phy_device *phydev) @@ -185,23 +234,21 @@ static int kszphy_config_init(struct phy_device *phydev) static int kszphy_config_init_led8041(struct phy_device *phydev) { - /* single led control, register 0x1e bits 15..14 */ - return kszphy_setup_led(phydev, 0x1e, 14); + return kszphy_setup_led(phydev, MII_KSZPHY_CTRL_1); } static int ksz8021_config_init(struct phy_device *phydev) { - const u16 val = KSZPHY_OMSO_B_CAST_OFF | KSZPHY_OMSO_RMII_OVERRIDE; int rc; - rc = kszphy_setup_led(phydev, 0x1f, 4); - if (rc) - dev_err(&phydev->dev, "failed to set led mode\n"); + kszphy_setup_led(phydev, MII_KSZPHY_CTRL_2); rc = ksz_config_flags(phydev); if (rc < 0) return rc; - rc = phy_write(phydev, MII_KSZPHY_OMSO, val); + + rc = kszphy_broadcast_disable(phydev); + return rc < 0 ? rc : 0; } @@ -209,14 +256,20 @@ static int ks8051_config_init(struct phy_device *phydev) { int rc; - rc = kszphy_setup_led(phydev, 0x1f, 4); - if (rc) - dev_err(&phydev->dev, "failed to set led mode\n"); + kszphy_setup_led(phydev, MII_KSZPHY_CTRL_2); rc = ksz_config_flags(phydev); return rc < 0 ? rc : 0; } +static int ksz8081_config_init(struct phy_device *phydev) +{ + kszphy_broadcast_disable(phydev); + kszphy_setup_led(phydev, MII_KSZPHY_CTRL_2); + + return 0; +} + static int ksz9021_load_values_from_of(struct phy_device *phydev, struct device_node *of_node, u16 reg, char *field1, char *field2, @@ -394,8 +447,8 @@ static int ksz9031_config_init(struct phy_device *phydev) } #define KSZ8873MLL_GLOBAL_CONTROL_4 0x06 -#define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX (1 << 6) -#define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED (1 << 4) +#define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX BIT(6) +#define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED BIT(4) static int ksz8873mll_read_status(struct phy_device *phydev) { int regval; @@ -579,7 +632,7 @@ static struct phy_driver ksphy_driver[] = { .phy_id_mask = 0x00fffff0, .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause), .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT, - .config_init = kszphy_config_init, + .config_init = ksz8081_config_init, .config_aneg = genphy_config_aneg, .read_status = genphy_read_status, .ack_interrupt = kszphy_ack_interrupt, |
