diff options
| -rw-r--r-- | arch/x86/kernel/tsc.c | 86 |
1 files changed, 83 insertions, 3 deletions
diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c index bb64beb301d9..dc1393e7cbfb 100644 --- a/arch/x86/kernel/tsc.c +++ b/arch/x86/kernel/tsc.c @@ -888,7 +888,82 @@ __cpuinit int unsynchronized_tsc(void) return 0; } -static void __init init_tsc_clocksource(void) + +static void tsc_refine_calibration_work(struct work_struct *work); +static DECLARE_DELAYED_WORK(tsc_irqwork, tsc_refine_calibration_work); +/** + * tsc_refine_calibration_work - Further refine tsc freq calibration + * @work - ignored. + * + * This functions uses delayed work over a period of a + * second to further refine the TSC freq value. Since this is + * timer based, instead of loop based, we don't block the boot + * process while this longer calibration is done. + * + * If there are any calibration anomolies (too many SMIs, etc), + * or the refined calibration is off by 1% of the fast early + * calibration, we throw out the new calibration and use the + * early calibration. + */ +static void tsc_refine_calibration_work(struct work_struct *work) +{ + static u64 tsc_start = -1, ref_start; + static int hpet; + u64 tsc_stop, ref_stop, delta; + unsigned long freq; + + /* Don't bother refining TSC on unstable systems */ + if (check_tsc_unstable()) + goto out; + + /* + * Since the work is started early in boot, we may be + * delayed the first time we expire. So set the workqueue + * again once we know timers are working. + */ + if (tsc_start == -1) { + /* + * Only set hpet once, to avoid mixing hardware + * if the hpet becomes enabled later. + */ + hpet = is_hpet_enabled(); + schedule_delayed_work(&tsc_irqwork, HZ); + tsc_start = tsc_read_refs(&ref_start, hpet); + return; + } + + tsc_stop = tsc_read_refs(&ref_stop, hpet); + + /* hpet or pmtimer available ? */ + if (!hpet && !ref_start && !ref_stop) + goto out; + + /* Check, whether the sampling was disturbed by an SMI */ + if (tsc_start == ULLONG_MAX || tsc_stop == ULLONG_MAX) + goto out; + + delta = tsc_stop - tsc_start; + delta *= 1000000LL; + if (hpet) + freq = calc_hpet_ref(delta, ref_start, ref_stop); + else + freq = calc_pmtimer_ref(delta, ref_start, ref_stop); + + /* Make sure we're within 1% */ + if (abs(tsc_khz - freq) > tsc_khz/100) + goto out; + + tsc_khz = freq; + printk(KERN_INFO "Refined TSC clocksource calibration: " + "%lu.%03lu MHz.\n", (unsigned long)tsc_khz / 1000, + (unsigned long)tsc_khz % 1000); + +out: + clocksource_register_khz(&clocksource_tsc, tsc_khz); +} + + +static int __init init_tsc_clocksource(void) { if (tsc_clocksource_reliable) clocksource_tsc.flags &= ~CLOCK_SOURCE_MUST_VERIFY; @@ -897,8 +972,14 @@ static void __init init_tsc_clocksource(void) clocksource_tsc.rating = 0; clocksource_tsc.flags &= ~CLOCK_SOURCE_IS_CONTINUOUS; } - clocksource_register_khz(&clocksource_tsc, tsc_khz); + schedule_delayed_work(&tsc_irqwork, 0); + return 0; } +/* + * We use device_initcall here, to ensure we run after the hpet + * is fully initialized, which may occur at fs_initcall time. + */ +device_initcall(init_tsc_clocksource); void __init tsc_init(void) { @@ -952,6 +1033,5 @@ void __init tsc_init(void) mark_tsc_unstable("TSCs unsynchronized"); check_system_tsc_reliable(); - init_tsc_clocksource(); } |
