Merge branch 'libertas-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes

1 files changed, 0 insertions, 275 deletions

diff --git a/drivers/net/wireless/libertas/README b/drivers/net/wireless/libertas/README
index 1f92f50b643c..0b133ce63805 100644
--- a/drivers/net/wireless/libertas/README
+++ b/drivers/net/wireless/libertas/README
@@ -28,281 +28,6 @@ DRIVER LOADING
 
 		insmod usb8388.ko [fw_name=usb8388.bin]
 
-=====================
-IWPRIV COMMAND
-=====================
-
-NAME
-	This manual describes the usage of private commands used in Marvell WLAN
-	Linux Driver. All the commands available in Wlanconfig will not be available
-	in the iwpriv.
-
-SYNOPSIS
-	iwpriv <ethX> <command> [sub-command] ...
-
-	iwpriv ethX setregioncode <n>
-	iwpriv ethX getregioncode
-
-Version 5 Command:
-	iwpriv ethX ledgpio <n>
-
-BT Commands:
-	The blinding table (BT) contains a list of mac addresses that will be,
-	by default, ignored by the firmware. It is also possible to invert this
-	behavior so that we will ignore all traffic except for the portion
-	coming from mac addresess in the list. It is primarily used for
-	debugging and testing networks.  It can be edited and inspected with
-	the following commands:
-
-	iwpriv ethX bt_reset
-	iwpriv ethX bt_add <mac_address>
-	iwpriv ethX bt_del <mac_address>
-	iwpriv ethX bt_list <id>
-	iwpriv ethX bt_get_invert <n>
-	iwpriv ethX bt_set_invert <n>
-
-FWT Commands:
-	The forwarding table (FWT) is a feature used to manage mesh network
-	routing in the firmware.  The FWT is essentially a routing table that
-	associates a destination mac address (da) with a next hop receiver
-	address (ra).  The FWT can be inspected and edited with the following
-	iwpriv commands, which are described in greater detail below.
-	Eventually, the table will be automatically maintained by a custom
-	routing protocol.
-
-	NOTE: FWT commands replace the previous DFT commands.  What were the DFT
-	commands?, you might ask.  They were an earlier API to the firmware that
-	implemented a simple MAC-layer forwarding mechanism.  In the unlikely
-	event that you were using these commands, you must migrate to the new
-	FWT commands which can be used to achieve the same functionality.
-
-	iwpriv ethX fwt_add [parameters]
-	iwpriv ethX fwt_del [parameters]
-	iwpriv ethX fwt_lookup [parameters]
-	iwpriv ethX fwt_list [parameters]
-	iwpriv ethX fwt_list_route [parameters]
-	iwpriv ethX fwt_list_neigh [parameters]
-	iwpriv ethX fwt_reset [parameters]
-	iwpriv ethX fwt_cleanup
-	iwpriv ethX fwt_time
-
-MESH Commands:
-
-	The MESH commands are used to configure various features of the mesh
-	routing protocol.  The following commands are supported:
-
-	iwpriv ethX mesh_get_ttl
-	iwpriv ethX mesh_set_ttl ttl
-
-DESCRIPTION
-	Those commands are used to send additional commands to the Marvell WLAN
-	card via the Linux device driver.
-
-	The ethX parameter specifies the network device that is to be used to
-		perform this command on. it could be eth0, eth1 etc.
-
-setregioncode
-	This command is used to set the region code in the station.
-	where value is 'region code' for various regions like
-	USA FCC, Canada IC, Spain, France, Europe ETSI,	Japan ...
-
-	Usage:
-		iwpriv ethX setregioncode 0x10: set region code to USA (0x10).
-
-getregioncode
-	This command is used to get the region code information set in the
-	station.
-
-ledgpio
-	This command is used to set/get LEDs.
-
-	iwpriv ethX ledgpio <LEDs>
-		will set the corresponding LED for the GPIO Line.
-
-	iwpriv ethX ledgpio
-		will give u which LEDs are Enabled.
-
-	Usage:
-		iwpriv eth1 ledgpio 1 0 2 1 3 4
-			will enable
-			LED 1 -> GPIO 0
-			LED 2 -> GPIO 1
-			LED 3 -> GPIO 4
-
-		iwpriv eth1 ledgpio
-			shows LED information in the format as mentioned above.
-
-	Note: LED0 is invalid
-	Note: Maximum Number of LEDs are 16.
-
-fwt_add
-	This command is used to insert an entry into the FWT table. The list of
-	parameters must follow the following structure:
-
-	iwpriv ethX fwt_add da ra [metric dir rate ssn dsn hopcount ttl expiration sleepmode snr]
-
-	The parameters between brackets are optional, but they must appear in
-	the order specified.  For example, if you want to specify the metric,
-	you must also specify the dir, ssn, and dsn but you need not specify the
-	hopcount, expiration, sleepmode, or snr.  Any unspecified parameters
-	will be assigned the defaults specified below.
-
-	The different parameters are:-
-		da		-- DA MAC address in the form 00:11:22:33:44:55
-		ra		-- RA MAC address in the form 00:11:22:33:44:55
-		metric		-- route metric (cost: smaller-metric routes are
-				   preferred, default is 0)
-		dir		-- direction (1 for direct, 0 for reverse,
-				   default is 1)
-		rate		-- data rate used for transmission to the RA,
-				   as specified for the rateadapt command,
-				   default is 3 (11Mbps)
-		ssn		-- Source Sequence Number (time at the RA for
-				   reverse routes.  Default is 0)
-		dsn		-- Destination Sequence Number (time at the DA
-				   for direct routes.  Default is 0)
-		hopcount	-- hop count (currently unused, default is 0)
-		ttl		-- TTL (Only used in reverse entries)
-		expiration	-- entry expiration (in ticks, where a tick is
-				   1024us, or ~ 1ms. Use 0 for an indefinite
-				   entry, default is 0)
-		sleepmode	-- RA's sleep mode (currently unused, default is
-				   0)
-		snr		-- SNR in the link to RA (currently unused,
-				   default is 0)
-
-	The command does not return anything.
-
-fwt_del
-	This command is used to remove an entry to the FWT table. The list of
-	parameters must follow the following structure:
-
-		iwpriv ethX fwt_del da ra [dir]
-
-	where the different parameters are:-
-		da		-- DA MAC address (in the form "00:11:22:33:44:55")
-		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
-		dir		-- direction (1 for direct, 0 for reverse,
-				   default is 1)
-
-	The command does not return anything.
-
-fwt_lookup
-	This command is used to get the best route in the FWT table to a given
-	host. The only parameter is the MAC address of the host that is being
-	looked for.
-
-		iwpriv ethX fwt_lookup da
-
-	where:-
-		da		-- DA MAC address (in the form "00:11:22:33:44:55")
-
-	The command returns an output string identical to the one returned by
-	fwt_list described below.
-
-
-fwt_list
-	This command is used to list a route from the FWT table. The only
-	parameter is the index into the table. If you want to list all the
-	routes in a table, start with index=0, and keep listing until you get a
-	"(null)" string.  Note that the indicies may change as the fwt is
-	updated.  It is expected that most users will not use fwt_list directly,
-	but that a utility similar to the traditional route command will be used
-	to invoke fwt_list over and over.
-
-		iwpriv ethX fwt_list index
-
-	The output is a string of the following form:
-
-		da ra valid metric dir rate ssn dsn hopcount ttl expiration
-		sleepmode snr precursor
-
-	where the different fields are:-
-		da		-- DA MAC address (in the form "00:11:22:33:44:55")
-		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
-		valid		-- whether the route is valid (0 if not valid)
-		metric		-- route metric (cost: smaller-metric routes are preferred)
-		dir		-- direction (1 for direct, 0 for reverse)
-		rate		-- data rate used for transmission to the RA,
-				   as specified for the rateadapt command
-		ssn		-- Source Sequence Number (time at the RA for reverse routes)
-		dsn		-- Destination Sequence Number (time at the DA for direct routes)
-		hopcount	-- hop count (currently unused)
-		ttl		-- TTL (only used in reverse entries)
-		expiration	-- entry expiration (in ticks, where a tick is 1024us, or ~ 1ms. Use 0 for an indefinite entry)
-		sleepmode	-- RA's sleep mode (currently unused)
-		snr		-- SNR in the link to RA (currently unused)
-		precursor	-- predecessor in direct routes
-
-fwt_list_route
-	This command is equivalent to fwt_list.
-
-fwt_list_neigh
-	This command is used to list a neighbor from the FWT table. The only
-	parameter is the neighbor ID. If you want to list all the neighbors in a
-	table, start with nid=0, and keep incrementing nid until you get a
-	"(null)" string.  Note that the nid from a fwt_list_route command can be
-	used as an input to this command.  Also note that this command is meant
-	mostly for debugging.  It is expected that users will use fwt_lookup.
-	One important reason for this is that the neighbor id may change as the
-	neighbor table is altered.
-
-		iwpriv ethX fwt_list_neigh nid
-
-	The output is a string of the following form:
-
-		ra sleepmode snr references
-
-	where the different fields are:-
-		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
-		sleepmode	-- RA's sleep mode (currently unused)
-		snr		-- SNR in the link to RA (currently unused)
-		references	-- RA's reference counter
-
-fwt_reset
-	This command is used to reset the FWT table, getting rid of all the
-	entries. There are no input parameters.
-
-		iwpriv ethX fwt_reset
-
-	The command does not return anything.
-
-fwt_cleanup
-	This command is used to perform user-based garbage recollection. The
-	FWT table is checked, and all the entries that are expired or invalid
-	are cleaned. Note that this is exported to the driver for debugging
-	purposes, as garbage collection is also fired by the firmware when in
-	space problems. There are no input parameters.
-
-		iwpriv ethX fwt_cleanup
-
-	The command does returns the number of invalid/expired routes deleted.
-
-fwt_time
-	This command returns a card's internal time representation.  It is this
-	time that is used to represent the expiration times of FWT entries.  The
-	number is not consistent from card to card; it is simply a timer count.
-	The fwt_time command is used to inspect the timer so that expiration
-	times reported by fwt_list can be properly interpreted.
-
-		iwpriv ethX fwt_time
-
-mesh_get_ttl
-
-	The mesh ttl is the number of hops a mesh packet can traverse before it
-	is dropped.  This parameter is used to prevent infinite loops in the
-	mesh network.  The value returned by this function is the ttl assigned
-	to all mesh packets.  Currently there is no way to control the ttl on a
-	per packet or per socket basis.
-
-	iwpriv ethX mesh_get_ttl
-
-mesh_set_ttl ttl
-
-	Set the ttl.  The argument must be between 0 and 255.
-
-	iwpriv ethX mesh_set_ttl <ttl>
-
 =========================
 ETHTOOL
 =========================