ide: remove useless subdirs from drivers/ide/

Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 706 insertions, 0 deletions

diff --git a/drivers/ide/it821x.c b/drivers/ide/it821x.c
new file mode 100644
index 000000000000..995e18bb3139
--- /dev/null
+++ b/drivers/ide/it821x.c
@@ -0,0 +1,706 @@
+/*
+ * Copyright (C) 2004		Red Hat <alan@redhat.com>
+ * Copyright (C) 2007		Bartlomiej Zolnierkiewicz
+ *
+ *  May be copied or modified under the terms of the GNU General Public License
+ *  Based in part on the ITE vendor provided SCSI driver.
+ *
+ *  Documentation available from
+ * 	http://www.ite.com.tw/pc/IT8212F_V04.pdf
+ *  Some other documents are NDA.
+ *
+ *  The ITE8212 isn't exactly a standard IDE controller. It has two
+ *  modes. In pass through mode then it is an IDE controller. In its smart
+ *  mode its actually quite a capable hardware raid controller disguised
+ *  as an IDE controller. Smart mode only understands DMA read/write and
+ *  identify, none of the fancier commands apply. The IT8211 is identical
+ *  in other respects but lacks the raid mode.
+ *
+ *  Errata:
+ *  o	Rev 0x10 also requires master/slave hold the same DMA timings and
+ *	cannot do ATAPI MWDMA.
+ *  o	The identify data for raid volumes lacks CHS info (technically ok)
+ *	but also fails to set the LBA28 and other bits. We fix these in
+ *	the IDE probe quirk code.
+ *  o	If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
+ *	raid then the controller firmware dies
+ *  o	Smart mode without RAID doesn't clear all the necessary identify
+ *	bits to reduce the command set to the one used
+ *
+ *  This has a few impacts on the driver
+ *  - In pass through mode we do all the work you would expect
+ *  - In smart mode the clocking set up is done by the controller generally
+ *    but we must watch the other limits and filter.
+ *  - There are a few extra vendor commands that actually talk to the
+ *    controller but only work PIO with no IRQ.
+ *
+ *  Vendor areas of the identify block in smart mode are used for the
+ *  timing and policy set up. Each HDD in raid mode also has a serial
+ *  block on the disk. The hardware extra commands are get/set chip status,
+ *  rebuild, get rebuild status.
+ *
+ *  In Linux the driver supports pass through mode as if the device was
+ *  just another IDE controller. If the smart mode is running then
+ *  volumes are managed by the controller firmware and each IDE "disk"
+ *  is a raid volume. Even more cute - the controller can do automated
+ *  hotplug and rebuild.
+ *
+ *  The pass through controller itself is a little demented. It has a
+ *  flaw that it has a single set of PIO/MWDMA timings per channel so
+ *  non UDMA devices restrict each others performance. It also has a
+ *  single clock source per channel so mixed UDMA100/133 performance
+ *  isn't perfect and we have to pick a clock. Thankfully none of this
+ *  matters in smart mode. ATAPI DMA is not currently supported.
+ *
+ *  It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
+ *
+ *  TODO
+ *	-	ATAPI UDMA is ok but not MWDMA it seems
+ *	-	RAID configuration ioctls
+ *	-	Move to libata once it grows up
+ */
+
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#define DRV_NAME "it821x"
+
+struct it821x_dev
+{
+	unsigned int smart:1,		/* Are we in smart raid mode */
+		timing10:1;		/* Rev 0x10 */
+	u8	clock_mode;		/* 0, ATA_50 or ATA_66 */
+	u8	want[2][2];		/* Mode/Pri log for master slave */
+	/* We need these for switching the clock when DMA goes on/off
+	   The high byte is the 66Mhz timing */
+	u16	pio[2];			/* Cached PIO values */
+	u16	mwdma[2];		/* Cached MWDMA values */
+	u16	udma[2];		/* Cached UDMA values (per drive) */
+};
+
+#define ATA_66		0
+#define ATA_50		1
+#define ATA_ANY		2
+
+#define UDMA_OFF	0
+#define MWDMA_OFF	0
+
+/*
+ *	We allow users to force the card into non raid mode without
+ *	flashing the alternative BIOS. This is also necessary right now
+ *	for embedded platforms that cannot run a PC BIOS but are using this
+ *	device.
+ */
+
+static int it8212_noraid;
+
+/**
+ *	it821x_program	-	program the PIO/MWDMA registers
+ *	@drive: drive to tune
+ *	@timing: timing info
+ *
+ *	Program the PIO/MWDMA timing for this channel according to the
+ *	current clock.
+ */
+
+static void it821x_program(ide_drive_t *drive, u16 timing)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int channel = hwif->channel;
+	u8 conf;
+
+	/* Program PIO/MWDMA timing bits */
+	if(itdev->clock_mode == ATA_66)
+		conf = timing >> 8;
+	else
+		conf = timing & 0xFF;
+
+	pci_write_config_byte(dev, 0x54 + 4 * channel, conf);
+}
+
+/**
+ *	it821x_program_udma	-	program the UDMA registers
+ *	@drive: drive to tune
+ *	@timing: timing info
+ *
+ *	Program the UDMA timing for this drive according to the
+ *	current clock.
+ */
+
+static void it821x_program_udma(ide_drive_t *drive, u16 timing)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int channel = hwif->channel;
+	u8 unit = drive->dn & 1, conf;
+
+	/* Program UDMA timing bits */
+	if(itdev->clock_mode == ATA_66)
+		conf = timing >> 8;
+	else
+		conf = timing & 0xFF;
+
+	if (itdev->timing10 == 0)
+		pci_write_config_byte(dev, 0x56 + 4 * channel + unit, conf);
+	else {
+		pci_write_config_byte(dev, 0x56 + 4 * channel, conf);
+		pci_write_config_byte(dev, 0x56 + 4 * channel + 1, conf);
+	}
+}
+
+/**
+ *	it821x_clock_strategy
+ *	@drive: drive to set up
+ *
+ *	Select between the 50 and 66Mhz base clocks to get the best
+ *	results for this interface.
+ */
+
+static void it821x_clock_strategy(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	ide_drive_t *pair;
+	int clock, altclock, sel = 0;
+	u8 unit = drive->dn & 1, v;
+
+	pair = &hwif->drives[1 - unit];
+
+	if(itdev->want[0][0] > itdev->want[1][0]) {
+		clock = itdev->want[0][1];
+		altclock = itdev->want[1][1];
+	} else {
+		clock = itdev->want[1][1];
+		altclock = itdev->want[0][1];
+	}
+
+	/*
+	 * if both clocks can be used for the mode with the higher priority
+	 * use the clock needed by the mode with the lower priority
+	 */
+	if (clock == ATA_ANY)
+		clock = altclock;
+
+	/* Nobody cares - keep the same clock */
+	if(clock == ATA_ANY)
+		return;
+	/* No change */
+	if(clock == itdev->clock_mode)
+		return;
+
+	/* Load this into the controller ? */
+	if(clock == ATA_66)
+		itdev->clock_mode = ATA_66;
+	else {
+		itdev->clock_mode = ATA_50;
+		sel = 1;
+	}
+
+	pci_read_config_byte(dev, 0x50, &v);
+	v &= ~(1 << (1 + hwif->channel));
+	v |= sel << (1 + hwif->channel);
+	pci_write_config_byte(dev, 0x50, v);
+
+	/*
+	 *	Reprogram the UDMA/PIO of the pair drive for the switch
+	 *	MWDMA will be dealt with by the dma switcher
+	 */
+	if(pair && itdev->udma[1-unit] != UDMA_OFF) {
+		it821x_program_udma(pair, itdev->udma[1-unit]);
+		it821x_program(pair, itdev->pio[1-unit]);
+	}
+	/*
+	 *	Reprogram the UDMA/PIO of our drive for the switch.
+	 *	MWDMA will be dealt with by the dma switcher
+	 */
+	if(itdev->udma[unit] != UDMA_OFF) {
+		it821x_program_udma(drive, itdev->udma[unit]);
+		it821x_program(drive, itdev->pio[unit]);
+	}
+}
+
+/**
+ *	it821x_set_pio_mode	-	set host controller for PIO mode
+ *	@drive: drive
+ *	@pio: PIO mode number
+ *
+ *	Tune the host to the desired PIO mode taking into the consideration
+ *	the maximum PIO mode supported by the other device on the cable.
+ */
+
+static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	ide_drive_t *pair;
+	u8 unit = drive->dn & 1, set_pio = pio;
+
+	/* Spec says 89 ref driver uses 88 */
+	static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
+	static u8 pio_want[]    = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
+
+	pair = &hwif->drives[1 - unit];
+
+	/*
+	 * Compute the best PIO mode we can for a given device. We must
+	 * pick a speed that does not cause problems with the other device
+	 * on the cable.
+	 */
+	if (pair) {
+		u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4);
+		/* trim PIO to the slowest of the master/slave */
+		if (pair_pio < set_pio)
+			set_pio = pair_pio;
+	}
+
+	/* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
+	itdev->want[unit][1] = pio_want[set_pio];
+	itdev->want[unit][0] = 1;	/* PIO is lowest priority */
+	itdev->pio[unit] = pio_timings[set_pio];
+	it821x_clock_strategy(drive);
+	it821x_program(drive, itdev->pio[unit]);
+}
+
+/**
+ *	it821x_tune_mwdma	-	tune a channel for MWDMA
+ *	@drive: drive to set up
+ *	@mode_wanted: the target operating mode
+ *
+ *	Load the timing settings for this device mode into the
+ *	controller when doing MWDMA in pass through mode. The caller
+ *	must manage the whole lack of per device MWDMA/PIO timings and
+ *	the shared MWDMA/PIO timing register.
+ */
+
+static void it821x_tune_mwdma (ide_drive_t *drive, byte mode_wanted)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
+	u8 unit = drive->dn & 1, channel = hwif->channel, conf;
+
+	static u16 dma[]	= { 0x8866, 0x3222, 0x3121 };
+	static u8 mwdma_want[]	= { ATA_ANY, ATA_66, ATA_ANY };
+
+	itdev->want[unit][1] = mwdma_want[mode_wanted];
+	itdev->want[unit][0] = 2;	/* MWDMA is low priority */
+	itdev->mwdma[unit] = dma[mode_wanted];
+	itdev->udma[unit] = UDMA_OFF;
+
+	/* UDMA bits off - Revision 0x10 do them in pairs */
+	pci_read_config_byte(dev, 0x50, &conf);
+	if (itdev->timing10)
+		conf |= channel ? 0x60: 0x18;
+	else
+		conf |= 1 << (3 + 2 * channel + unit);
+	pci_write_config_byte(dev, 0x50, conf);
+
+	it821x_clock_strategy(drive);
+	/* FIXME: do we need to program this ? */
+	/* it821x_program(drive, itdev->mwdma[unit]); */
+}
+
+/**
+ *	it821x_tune_udma	-	tune a channel for UDMA
+ *	@drive: drive to set up
+ *	@mode_wanted: the target operating mode
+ *
+ *	Load the timing settings for this device mode into the
+ *	controller when doing UDMA modes in pass through.
+ */
+
+static void it821x_tune_udma (ide_drive_t *drive, byte mode_wanted)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	u8 unit = drive->dn & 1, channel = hwif->channel, conf;
+
+	static u16 udma[]	= { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
+	static u8 udma_want[]	= { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
+
+	itdev->want[unit][1] = udma_want[mode_wanted];
+	itdev->want[unit][0] = 3;	/* UDMA is high priority */
+	itdev->mwdma[unit] = MWDMA_OFF;
+	itdev->udma[unit] = udma[mode_wanted];
+	if(mode_wanted >= 5)
+		itdev->udma[unit] |= 0x8080;	/* UDMA 5/6 select on */
+
+	/* UDMA on. Again revision 0x10 must do the pair */
+	pci_read_config_byte(dev, 0x50, &conf);
+	if (itdev->timing10)
+		conf &= channel ? 0x9F: 0xE7;
+	else
+		conf &= ~ (1 << (3 + 2 * channel + unit));
+	pci_write_config_byte(dev, 0x50, conf);
+
+	it821x_clock_strategy(drive);
+	it821x_program_udma(drive, itdev->udma[unit]);
+
+}
+
+/**
+ *	it821x_dma_read	-	DMA hook
+ *	@drive: drive for DMA
+ *
+ *	The IT821x has a single timing register for MWDMA and for PIO
+ *	operations. As we flip back and forth we have to reload the
+ *	clock. In addition the rev 0x10 device only works if the same
+ *	timing value is loaded into the master and slave UDMA clock
+ * 	so we must also reload that.
+ *
+ *	FIXME: we could figure out in advance if we need to do reloads
+ */
+
+static void it821x_dma_start(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	u8 unit = drive->dn & 1;
+
+	if(itdev->mwdma[unit] != MWDMA_OFF)
+		it821x_program(drive, itdev->mwdma[unit]);
+	else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10)
+		it821x_program_udma(drive, itdev->udma[unit]);
+	ide_dma_start(drive);
+}
+
+/**
+ *	it821x_dma_write	-	DMA hook
+ *	@drive: drive for DMA stop
+ *
+ *	The IT821x has a single timing register for MWDMA and for PIO
+ *	operations. As we flip back and forth we have to reload the
+ *	clock.
+ */
+
+static int it821x_dma_end(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int ret = ide_dma_end(drive);
+	u8 unit = drive->dn & 1;
+
+	if(itdev->mwdma[unit] != MWDMA_OFF)
+		it821x_program(drive, itdev->pio[unit]);
+	return ret;
+}
+
+/**
+ *	it821x_set_dma_mode	-	set host controller for DMA mode
+ *	@drive: drive
+ *	@speed: DMA mode
+ *
+ *	Tune the ITE chipset for the desired DMA mode.
+ */
+
+static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed)
+{
+	/*
+	 * MWDMA tuning is really hard because our MWDMA and PIO
+	 * timings are kept in the same place.  We can switch in the
+	 * host dma on/off callbacks.
+	 */
+	if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6)
+		it821x_tune_udma(drive, speed - XFER_UDMA_0);
+	else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+		it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
+}
+
+/**
+ *	it821x_cable_detect	-	cable detection
+ *	@hwif: interface to check
+ *
+ *	Check for the presence of an ATA66 capable cable on the
+ *	interface. Problematic as it seems some cards don't have
+ *	the needed logic onboard.
+ */
+
+static u8 it821x_cable_detect(ide_hwif_t *hwif)
+{
+	/* The reference driver also only does disk side */
+	return ATA_CBL_PATA80;
+}
+
+/**
+ *	it821x_quirkproc	-	post init callback
+ *	@drive: drive
+ *
+ *	This callback is run after the drive has been probed but
+ *	before anything gets attached. It allows drivers to do any
+ *	final tuning that is needed, or fixups to work around bugs.
+ */
+
+static void it821x_quirkproc(ide_drive_t *drive)
+{
+	struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif);
+	u16 *id = drive->id;
+
+	if (!itdev->smart) {
+		/*
+		 *	If we are in pass through mode then not much
+		 *	needs to be done, but we do bother to clear the
+		 *	IRQ mask as we may well be in PIO (eg rev 0x10)
+		 *	for now and we know unmasking is safe on this chipset.
+		 */
+		drive->dev_flags |= IDE_DFLAG_UNMASK;
+	} else {
+	/*
+	 *	Perform fixups on smart mode. We need to "lose" some
+	 *	capabilities the firmware lacks but does not filter, and
+	 *	also patch up some capability bits that it forgets to set
+	 *	in RAID mode.
+	 */
+
+		/* Check for RAID v native */
+		if (strstr((char *)&id[ATA_ID_PROD],
+			   "Integrated Technology Express")) {
+			/* In raid mode the ident block is slightly buggy
+			   We need to set the bits so that the IDE layer knows
+			   LBA28. LBA48 and DMA ar valid */
+			id[ATA_ID_CAPABILITY]    |= (3 << 8); /* LBA28, DMA */
+			id[ATA_ID_COMMAND_SET_2] |= 0x0400;   /* LBA48 valid */
+			id[ATA_ID_CFS_ENABLE_2]  |= 0x0400;   /* LBA48 on */
+			/* Reporting logic */
+			printk(KERN_INFO "%s: IT8212 %sRAID %d volume",
+				drive->name, id[147] ? "Bootable " : "",
+				id[ATA_ID_CSFO]);
+			if (id[ATA_ID_CSFO] != 1)
+				printk(KERN_CONT "(%dK stripe)", id[146]);
+			printk(KERN_CONT ".\n");
+		} else {
+			/* Non RAID volume. Fixups to stop the core code
+			   doing unsupported things */
+			id[ATA_ID_FIELD_VALID]	 &= 3;
+			id[ATA_ID_QUEUE_DEPTH]	  = 0;
+			id[ATA_ID_COMMAND_SET_1]  = 0;
+			id[ATA_ID_COMMAND_SET_2] &= 0xC400;
+			id[ATA_ID_CFSSE]	 &= 0xC000;
+			id[ATA_ID_CFS_ENABLE_1]	  = 0;
+			id[ATA_ID_CFS_ENABLE_2]	 &= 0xC400;
+			id[ATA_ID_CSF_DEFAULT]	 &= 0xC000;
+			id[127]			  = 0;
+			id[ATA_ID_DLF]		  = 0;
+			id[ATA_ID_CSFO]		  = 0;
+			id[ATA_ID_CFA_POWER]	  = 0;
+			printk(KERN_INFO "%s: Performing identify fixups.\n",
+				drive->name);
+		}
+
+		/*
+		 * Set MWDMA0 mode as enabled/support - just to tell
+		 * IDE core that DMA is supported (it821x hardware
+		 * takes care of DMA mode programming).
+		 */
+		if (ata_id_has_dma(id)) {
+			id[ATA_ID_MWDMA_MODES] |= 0x0101;
+			drive->current_speed = XFER_MW_DMA_0;
+		}
+	}
+
+}
+
+static struct ide_dma_ops it821x_pass_through_dma_ops = {
+	.dma_host_set		= ide_dma_host_set,
+	.dma_setup		= ide_dma_setup,
+	.dma_exec_cmd		= ide_dma_exec_cmd,
+	.dma_start		= it821x_dma_start,
+	.dma_end		= it821x_dma_end,
+	.dma_test_irq		= ide_dma_test_irq,
+	.dma_timeout		= ide_dma_timeout,
+	.dma_lost_irq		= ide_dma_lost_irq,
+};
+
+/**
+ *	init_hwif_it821x	-	set up hwif structs
+ *	@hwif: interface to set up
+ *
+ *	We do the basic set up of the interface structure. The IT8212
+ *	requires several custom handlers so we override the default
+ *	ide DMA handlers appropriately
+ */
+
+static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
+{
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	struct ide_host *host = pci_get_drvdata(dev);
+	struct it821x_dev *itdevs = host->host_priv;
+	struct it821x_dev *idev = itdevs + hwif->channel;
+	u8 conf;
+
+	ide_set_hwifdata(hwif, idev);
+
+	pci_read_config_byte(dev, 0x50, &conf);
+	if (conf & 1) {
+		idev->smart = 1;
+		hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
+		/* Long I/O's although allowed in LBA48 space cause the
+		   onboard firmware to enter the twighlight zone */
+		hwif->rqsize = 256;
+	}
+
+	/* Pull the current clocks from 0x50 also */
+	if (conf & (1 << (1 + hwif->channel)))
+		idev->clock_mode = ATA_50;
+	else
+		idev->clock_mode = ATA_66;
+
+	idev->want[0][1] = ATA_ANY;
+	idev->want[1][1] = ATA_ANY;
+
+	/*
+	 *	Not in the docs but according to the reference driver
+	 *	this is necessary.
+	 */
+
+	pci_read_config_byte(dev, 0x08, &conf);
+	if (conf == 0x10) {
+		idev->timing10 = 1;
+		hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
+		if (idev->smart == 0)
+			printk(KERN_WARNING DRV_NAME " %s: revision 0x10, "
+				"workarounds activated\n", pci_name(dev));
+	}
+
+	if (idev->smart == 0) {
+		/* MWDMA/PIO clock switching for pass through mode */
+		hwif->dma_ops = &it821x_pass_through_dma_ops;
+	} else
+		hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
+
+	if (hwif->dma_base == 0)
+		return;
+
+	hwif->ultra_mask = ATA_UDMA6;
+	hwif->mwdma_mask = ATA_MWDMA2;
+}
+
+static void it8212_disable_raid(struct pci_dev *dev)
+{
+	/* Reset local CPU, and set BIOS not ready */
+	pci_write_config_byte(dev, 0x5E, 0x01);
+
+	/* Set to bypass mode, and reset PCI bus */
+	pci_write_config_byte(dev, 0x50, 0x00);
+	pci_write_config_word(dev, PCI_COMMAND,
+			      PCI_COMMAND_PARITY | PCI_COMMAND_IO |
+			      PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+	pci_write_config_word(dev, 0x40, 0xA0F3);
+
+	pci_write_config_dword(dev,0x4C, 0x02040204);
+	pci_write_config_byte(dev, 0x42, 0x36);
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
+}
+
+static unsigned int init_chipset_it821x(struct pci_dev *dev)
+{
+	u8 conf;
+	static char *mode[2] = { "pass through", "smart" };
+
+	/* Force the card into bypass mode if so requested */
+	if (it8212_noraid) {
+		printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n",
+			pci_name(dev));
+		it8212_disable_raid(dev);
+	}
+	pci_read_config_byte(dev, 0x50, &conf);
+	printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n",
+		pci_name(dev), mode[conf & 1]);
+	return 0;
+}
+
+static const struct ide_port_ops it821x_port_ops = {
+	/* it821x_set_{pio,dma}_mode() are only used in pass-through mode */
+	.set_pio_mode		= it821x_set_pio_mode,
+	.set_dma_mode		= it821x_set_dma_mode,
+	.quirkproc		= it821x_quirkproc,
+	.cable_detect		= it821x_cable_detect,
+};
+
+static const struct ide_port_info it821x_chipset __devinitdata = {
+	.name		= DRV_NAME,
+	.init_chipset	= init_chipset_it821x,
+	.init_hwif	= init_hwif_it821x,
+	.port_ops	= &it821x_port_ops,
+	.pio_mask	= ATA_PIO4,
+};
+
+/**
+ *	it821x_init_one	-	pci layer discovery entry
+ *	@dev: PCI device
+ *	@id: ident table entry
+ *
+ *	Called by the PCI code when it finds an ITE821x controller.
+ *	We then use the IDE PCI generic helper to do most of the work.
+ */
+
+static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	struct it821x_dev *itdevs;
+	int rc;
+
+	itdevs = kzalloc(2 * sizeof(*itdevs), GFP_KERNEL);
+	if (itdevs == NULL) {
+		printk(KERN_ERR DRV_NAME " %s: out of memory\n", pci_name(dev));
+		return -ENOMEM;
+	}
+
+	rc = ide_pci_init_one(dev, &it821x_chipset, itdevs);
+	if (rc)
+		kfree(itdevs);
+
+	return rc;
+}
+
+static void __devexit it821x_remove(struct pci_dev *dev)
+{
+	struct ide_host *host = pci_get_drvdata(dev);
+	struct it821x_dev *itdevs = host->host_priv;
+
+	ide_pci_remove(dev);
+	kfree(itdevs);
+}
+
+static const struct pci_device_id it821x_pci_tbl[] = {
+	{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 },
+	{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 },
+	{ 0, },
+};
+
+MODULE_DEVICE_TABLE(pci, it821x_pci_tbl);
+
+static struct pci_driver it821x_pci_driver = {
+	.name		= "ITE821x IDE",
+	.id_table	= it821x_pci_tbl,
+	.probe		= it821x_init_one,
+	.remove		= __devexit_p(it821x_remove),
+	.suspend	= ide_pci_suspend,
+	.resume		= ide_pci_resume,
+};
+
+static int __init it821x_ide_init(void)
+{
+	return ide_pci_register_driver(&it821x_pci_driver);
+}
+
+static void __exit it821x_ide_exit(void)
+{
+	pci_unregister_driver(&it821x_pci_driver);
+}
+
+module_init(it821x_ide_init);
+module_exit(it821x_ide_exit);
+
+module_param_named(noraid, it8212_noraid, int, S_IRUGO);
+MODULE_PARM_DESC(noraid, "Force card into bypass mode");
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("PCI driver module for the ITE 821x");
+MODULE_LICENSE("GPL");