Merge branch 'for_3.3/uart/runtime-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into uart

Conflicts:
	arch/arm/mach-omap2/pm34xx.c

32 files changed, 563 insertions, 1062 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 50f43942c1aa..a34d0f7d1bfa 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -76,8 +76,13 @@ config SOC_OMAP3430
 	default y
 	select ARCH_OMAP_OTG
 
-config SOC_OMAPTI816X
-	bool "TI816X support"
+config SOC_OMAPTI81XX
+	bool "TI81XX support"
+	depends on ARCH_OMAP3
+	default y
+
+config SOC_OMAPAM33XX
+	bool "AM33XX support"
 	depends on ARCH_OMAP3
 	default y
 
@@ -314,7 +319,7 @@ config MACH_OMAP_3630SDP
 
 config MACH_TI8168EVM
 	bool "TI8168 Evaluation Module"
-	depends on SOC_OMAPTI816X
+	depends on SOC_OMAPTI81XX
 	default y
 
 config MACH_OMAP_4430SDP
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 83126368ed99..109b434159f5 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -475,106 +475,8 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
-
-static struct omap_device_pad serial1_pads[] __initdata = {
-	/*
-	 * Note that off output enable is an active low
-	 * signal. So setting this means pin is a
-	 * input enabled in off mode
-	 */
-	OMAP_MUX_STATIC("uart1_cts.uart1_cts",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rts.uart1_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rx.uart1_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_tx.uart1_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLDOWN |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial1_data __initdata = {
-	.id		= 0,
-	.pads		= serial1_pads,
-	.pads_cnt	= ARRAY_SIZE(serial1_pads),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init_port(&serial1_data);
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /*
@@ -711,7 +613,7 @@ static void __init omap_3430sdp_init(void)
 	else
 		gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
 	omap_ads7846_init(1, gpio_pendown, 310, NULL);
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(hyb18m512160af6_sdrc_params, NULL);
 	usb_musb_init(NULL);
 	board_smc91x_init();
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index ef2bbc09428a..5f264fad69bc 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -837,74 +837,8 @@ static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial4_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static struct omap_board_data serial4_data __initdata = {
-	.id		= 3,
-	.pads		= serial4_pads,
-	.pads_cnt	= ARRAY_SIZE(serial4_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	struct omap_board_data bdata;
-	bdata.flags	= 0;
-	bdata.pads	= NULL;
-	bdata.pads_cnt	= 0;
-	bdata.id	= 0;
-	/* pass dummy data for UART1 */
-	omap_serial_init_port(&bdata);
-
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-	omap_serial_init_port(&serial4_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
  #endif
 
 static void omap4_sdp4430_wifi_mux_init(void)
@@ -954,7 +888,7 @@ static void __init omap_4430sdp_init(void)
 	omap4_i2c_init();
 	omap_sfh7741prox_init();
 	platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices));
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 	omap4_sdp4430_wifi_init();
 	omap4_twl6030_hsmmc_init(mmc);
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index bebd3d84365e..118f38c4b37d 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -644,15 +644,15 @@ static inline void board_serial_init(void)
 	bdata.pads_cnt = 0;
 
 	bdata.id = 0;
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 
 	bdata.id = 1;
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 
 	bdata.id = 2;
 	bdata.pads = serial2_pads;
 	bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
-	omap_serial_init_port(&bdata);
+	omap_serial_init_port(&bdata, NULL);
 }
 
 #else
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index b6f114436dbc..ea45f5835103 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -364,74 +364,8 @@ static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial4_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart4_rx.uart4_rx",
-			 OMAP_PIN_INPUT | OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart4_tx.uart4_tx",
-			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id             = 1,
-	.pads           = serial2_pads,
-	.pads_cnt       = ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id             = 2,
-	.pads           = serial3_pads,
-	.pads_cnt       = ARRAY_SIZE(serial3_pads),
-};
-
-static struct omap_board_data serial4_data __initdata = {
-	.id             = 3,
-	.pads           = serial4_pads,
-	.pads_cnt       = ARRAY_SIZE(serial4_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	struct omap_board_data bdata;
-	bdata.flags     = 0;
-	bdata.pads      = NULL;
-	bdata.pads_cnt  = 0;
-	bdata.id        = 0;
-	/* pass dummy data for UART1 */
-	omap_serial_init_port(&bdata);
-
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-	omap_serial_init_port(&serial4_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /* Display DVI */
@@ -562,7 +496,7 @@ static void __init omap4_panda_init(void)
 	omap4_panda_i2c_init();
 	platform_add_devices(panda_devices, ARRAY_SIZE(panda_devices));
 	platform_device_register(&omap_vwlan_device);
-	board_serial_init();
+	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 	omap4_twl6030_hsmmc_init(mmc);
 	omap4_ehci_init();
diff --git a/arch/arm/mach-omap2/board-ti8168evm.c b/arch/arm/mach-omap2/board-ti8168evm.c
index 8402b39b2840..b236fcc023ac 100644
--- a/arch/arm/mach-omap2/board-ti8168evm.c
+++ b/arch/arm/mach-omap2/board-ti8168evm.c
@@ -35,17 +35,12 @@ static void __init ti8168_evm_init(void)
 	omap_board_config_size = ARRAY_SIZE(ti8168_evm_config);
 }
 
-static void __init ti8168_evm_map_io(void)
-{
-	omapti816x_map_common_io();
-}
-
 MACHINE_START(TI8168EVM, "ti8168evm")
 	/* Maintainer: Texas Instruments */
 	.atag_offset	= 0x100,
-	.map_io		= ti8168_evm_map_io,
-	.init_early	= ti816x_init_early,
-	.init_irq	= ti816x_init_irq,
+	.map_io		= ti81xx_map_io,
+	.init_early	= ti81xx_init_early,
+	.init_irq	= ti81xx_init_irq,
 	.timer		= &omap3_timer,
 	.init_machine	= ti8168_evm_init,
 MACHINE_END
diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
index 1f3481f8d695..f57ed5baeccf 100644
--- a/arch/arm/mach-omap2/clock.c
+++ b/arch/arm/mach-omap2/clock.c
@@ -35,7 +35,7 @@
 #include "cm-regbits-24xx.h"
 #include "cm-regbits-34xx.h"
 
-u8 cpu_mask;
+u16 cpu_mask;
 
 /*
  * clkdm_control: if true, then when a clock is enabled in the
diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h
index 2311bc217226..b8c2a686481c 100644
--- a/arch/arm/mach-omap2/clock.h
+++ b/arch/arm/mach-omap2/clock.h
@@ -132,7 +132,7 @@ void omap2_clk_print_new_rates(const char *hfclkin_ck_name,
 			       const char *core_ck_name,
 			       const char *mpu_ck_name);
 
-extern u8 cpu_mask;
+extern u16 cpu_mask;
 
 extern const struct clkops clkops_omap2_dflt_wait;
 extern const struct clkops clkops_dummy;
diff --git a/arch/arm/mach-omap2/clock3xxx_data.c b/arch/arm/mach-omap2/clock3xxx_data.c
index 5d0064a4fb5a..60424f41156b 100644
--- a/arch/arm/mach-omap2/clock3xxx_data.c
+++ b/arch/arm/mach-omap2/clock3xxx_data.c
@@ -3517,6 +3517,10 @@ int __init omap3xxx_clk_init(void)
 	} else if (cpu_is_ti816x()) {
 		cpu_mask = RATE_IN_TI816X;
 		cpu_clkflg = CK_TI816X;
+	} else if (cpu_is_am33xx()) {
+		cpu_mask = RATE_IN_AM33XX;
+	} else if (cpu_is_ti814x()) {
+		cpu_mask = RATE_IN_TI814X;
 	} else if (cpu_is_omap34xx()) {
 		if (omap_rev() == OMAP3430_REV_ES1_0) {
 			cpu_mask = RATE_IN_3430ES1;
@@ -3600,7 +3604,7 @@ int __init omap3xxx_clk_init(void)
 	 * Lock DPLL5 -- here only until other device init code can
 	 * handle this
 	 */
-	if (!cpu_is_ti816x() && (omap_rev() >= OMAP3430_REV_ES2_0))
+	if (!cpu_is_ti81xx() && (omap_rev() >= OMAP3430_REV_ES2_0))
 		omap3_clk_lock_dpll5();
 
 	/* Avoid sleeping during omap3_core_dpll_m2_set_rate() */
diff --git a/arch/arm/mach-omap2/common.c b/arch/arm/mach-omap2/common.c
index 684b8a7cd401..aaf421178c91 100644
--- a/arch/arm/mach-omap2/common.c
+++ b/arch/arm/mach-omap2/common.c
@@ -110,23 +110,49 @@ void __init omap3_map_io(void)
 
 /*
  * Adjust TAP register base such that omap3_check_revision accesses the correct
- * TI816X register for checking device ID (it adds 0x204 to tap base while
- * TI816X DEVICE ID register is at offset 0x600 from control base).
+ * TI81XX register for checking device ID (it adds 0x204 to tap base while
+ * TI81XX DEVICE ID register is at offset 0x600 from control base).
  */
-#define TI816X_TAP_BASE		(TI816X_CTRL_BASE + \
-				TI816X_CONTROL_DEVICE_ID - 0x204)
+#define TI81XX_TAP_BASE		(TI81XX_CTRL_BASE + \
+				TI81XX_CONTROL_DEVICE_ID - 0x204)
 
-static struct omap_globals ti816x_globals = {
+static struct omap_globals ti81xx_globals = {
 	.class  = OMAP343X_CLASS,
-	.tap    = OMAP2_L4_IO_ADDRESS(TI816X_TAP_BASE),
-	.ctrl   = OMAP2_L4_IO_ADDRESS(TI816X_CTRL_BASE),
-	.prm    = OMAP2_L4_IO_ADDRESS(TI816X_PRCM_BASE),
-	.cm     = OMAP2_L4_IO_ADDRESS(TI816X_PRCM_BASE),
+	.tap    = OMAP2_L4_IO_ADDRESS(TI81XX_TAP_BASE),
+	.ctrl   = OMAP2_L4_IO_ADDRESS(TI81XX_CTRL_BASE),
+	.prm    = OMAP2_L4_IO_ADDRESS(TI81XX_PRCM_BASE),
+	.cm     = OMAP2_L4_IO_ADDRESS(TI81XX_PRCM_BASE),
 };
 
-void __init omap2_set_globals_ti816x(void)
+void __init omap2_set_globals_ti81xx(void)
 {
-	__omap2_set_globals(&ti816x_globals);
+	__omap2_set_globals(&ti81xx_globals);
+}
+
+void __init ti81xx_map_io(void)
+{
+	omapti81xx_map_common_io();
+}
+
+#define AM33XX_TAP_BASE		(AM33XX_CTRL_BASE + \
+				TI81XX_CONTROL_DEVICE_ID - 0x204)
+
+static struct omap_globals am33xx_globals = {
+	.class  = AM335X_CLASS,
+	.tap    = AM33XX_L4_WK_IO_ADDRESS(AM33XX_TAP_BASE),
+	.ctrl   = AM33XX_L4_WK_IO_ADDRESS(AM33XX_CTRL_BASE),
+	.prm    = AM33XX_L4_WK_IO_ADDRESS(AM33XX_PRCM_BASE),
+	.cm     = AM33XX_L4_WK_IO_ADDRESS(AM33XX_PRCM_BASE),
+};
+
+void __init omap2_set_globals_am33xx(void)
+{
+	__omap2_set_globals(&am33xx_globals);
+}
+
+void __init am33xx_map_io(void)
+{
+	omapam33xx_map_common_io();
 }
 #endif
 
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 0911e843f079..90bd2ae85596 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -54,10 +54,18 @@ static inline void omap34xx_map_common_io(void)
 }
 #endif
 
-#ifdef CONFIG_SOC_OMAPTI816X
-extern void omapti816x_map_common_io(void);
+#ifdef CONFIG_SOC_OMAPTI81XX
+extern void omapti81xx_map_common_io(void);
 #else
-static inline void omapti816x_map_common_io(void)
+static inline void omapti81xx_map_common_io(void)
+{
+}
+#endif
+
+#ifdef CONFIG_SOC_OMAPAM33XX
+extern void omapam33xx_map_common_io(void);
+#else
+static inline void omapam33xx_map_common_io(void)
 {
 }
 #endif
@@ -84,7 +92,7 @@ void omap35xx_init_early(void);
 void omap3630_init_early(void);
 void omap3_init_early(void);	/* Do not use this one */
 void am35xx_init_early(void);
-void ti816x_init_early(void);
+void ti81xx_init_early(void);
 void omap4430_init_early(void);
 
 /*
@@ -108,7 +116,8 @@ void omap2_set_globals_242x(void);
 void omap2_set_globals_243x(void);
 void omap2_set_globals_3xxx(void);
 void omap2_set_globals_443x(void);
-void omap2_set_globals_ti816x(void);
+void omap2_set_globals_ti81xx(void);
+void omap2_set_globals_am33xx(void);
 
 /* These get called from omap2_set_globals_xxxx(), do not call these */
 void omap2_set_globals_tap(struct omap_globals *);
@@ -119,7 +128,9 @@ void omap2_set_globals_prcm(struct omap_globals *);
 void omap242x_map_io(void);
 void omap243x_map_io(void);
 void omap3_map_io(void);
+void am33xx_map_io(void);
 void omap4_map_io(void);
+void ti81xx_map_io(void);
 
 /**
  * omap_test_timeout - busy-loop, testing a condition
@@ -148,7 +159,7 @@ extern struct device *omap4_get_dsp_device(void);
 
 void omap2_init_irq(void);
 void omap3_init_irq(void);
-void ti816x_init_irq(void);
+void ti81xx_init_irq(void);
 extern int omap_irq_pending(void);
 void omap_intc_save_context(void);
 void omap_intc_restore_context(void);
diff --git a/arch/arm/mach-omap2/control.h b/arch/arm/mach-omap2/control.h
index d4ef75d5a382..0ba68d3764bc 100644
--- a/arch/arm/mach-omap2/control.h
+++ b/arch/arm/mach-omap2/control.h
@@ -52,8 +52,8 @@
 #define OMAP343X_CONTROL_PADCONFS_WKUP	0xa00
 #define OMAP343X_CONTROL_GENERAL_WKUP	0xa60
 
-/* TI816X spefic control submodules */
-#define TI816X_CONTROL_DEVCONF		0x600
+/* TI81XX spefic control submodules */
+#define TI81XX_CONTROL_DEVCONF		0x600
 
 /* Control register offsets - read/write with omap_ctrl_{read,write}{bwl}() */
 
@@ -244,8 +244,8 @@
 #define OMAP3_PADCONF_SAD2D_MSTANDBY   0x250
 #define OMAP3_PADCONF_SAD2D_IDLEACK    0x254
 
-/* TI816X CONTROL_DEVCONF register offsets */
-#define TI816X_CONTROL_DEVICE_ID	(TI816X_CONTROL_DEVCONF + 0x000)
+/* TI81XX CONTROL_DEVCONF register offsets */
+#define TI81XX_CONTROL_DEVICE_ID	(TI81XX_CONTROL_DEVCONF + 0x000)
 
 /*
  * REVISIT: This list of registers is not comprehensive - there are more
diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c
index 1f71ebb6c12c..464cffde58fe 100644
--- a/arch/arm/mach-omap2/cpuidle34xx.c
+++ b/arch/arm/mach-omap2/cpuidle34xx.c
@@ -31,7 +31,6 @@
 #include <plat/irqs.h>
 #include "powerdomain.h"
 #include "clockdomain.h"
-#include <plat/serial.h>
 
 #include "pm.h"
 #include "control.h"
@@ -260,11 +259,6 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev,
 	struct omap3_idle_statedata *cx;
 	int ret;
 
-	if (!omap3_can_sleep()) {
-		new_state_idx = drv->safe_state_index;
-		goto select_state;
-	}
-
 	/*
 	 * Prevent idle completely if CAM is active.
 	 * CAM does not have wakeup capability in OMAP3.
diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c
index 27ad722df637..6c5826605eae 100644
--- a/arch/arm/mach-omap2/id.c
+++ b/arch/arm/mach-omap2/id.c
@@ -226,7 +226,7 @@ static void __init omap4_check_features(void)
 	}
 }
 
-static void __init ti816x_check_features(void)
+static void __init ti81xx_check_features(void)
 {
 	omap_features = OMAP3_HAS_NEON;
 }
@@ -340,6 +340,29 @@ static void __init omap3_check_revision(const char **cpu_rev)
 			break;
 		}
 		break;
+	case 0xb944:
+		omap_revision = AM335X_REV_ES1_0;
+		*cpu_rev = "1.0";
+	case 0xb8f2:
+		switch (rev) {
+		case 0:
+		/* FALLTHROUGH */
+		case 1:
+			omap_revision = TI8148_REV_ES1_0;
+			*cpu_rev = "1.0";
+			break;
+		case 2:
+			omap_revision = TI8148_REV_ES2_0;
+			*cpu_rev = "2.0";
+			break;
+		case 3:
+		/* FALLTHROUGH */
+		default:
+			omap_revision = TI8148_REV_ES2_1;
+			*cpu_rev = "2.1";
+			break;
+		}
+		break;
 	default:
 		/* Unknown default to latest silicon rev as default */
 		omap_revision = OMAP3630_REV_ES1_2;
@@ -367,7 +390,7 @@ static void __init omap4_check_revision(void)
 	 * Few initial 4430 ES2.0 samples IDCODE is same as ES1.0
 	 * Use ARM register to detect the correct ES version
 	 */
-	if (!rev && (hawkeye != 0xb94e)) {
+	if (!rev && (hawkeye != 0xb94e) && (hawkeye != 0xb975)) {
 		idcode = read_cpuid(CPUID_ID);
 		rev = (idcode & 0xf) - 1;
 	}
@@ -389,8 +412,11 @@ static void __init omap4_check_revision(void)
 			omap_revision = OMAP4430_REV_ES2_1;
 			break;
 		case 4:
-		default:
 			omap_revision = OMAP4430_REV_ES2_2;
+			break;
+		case 6:
+		default:
+			omap_revision = OMAP4430_REV_ES2_3;
 		}
 		break;
 	case 0xb94e:
@@ -401,9 +427,17 @@ static void __init omap4_check_revision(void)
 			break;
 		}
 		break;
+	case 0xb975:
+		switch (rev) {
+		case 0:
+		default:
+			omap_revision = OMAP4470_REV_ES1_0;
+			break;
+		}
+		break;
 	default:
 		/* Unknown default to latest silicon rev as default */
-		omap_revision = OMAP4430_REV_ES2_2;
+		omap_revision = OMAP4430_REV_ES2_3;
 	}
 
 	pr_info("OMAP%04x ES%d.%d\n", omap_rev() >> 16,
@@ -432,6 +466,10 @@ static void __init omap3_cpuinfo(const char *cpu_rev)
 		cpu_name = (omap3_has_sgx()) ? "AM3517" : "AM3505";
 	} else if (cpu_is_ti816x()) {
 		cpu_name = "TI816X";
+	} else if (cpu_is_am335x()) {
+		cpu_name =  "AM335X";
+	} else if (cpu_is_ti814x()) {
+		cpu_name = "TI814X";
 	} else if (omap3_has_iva() && omap3_has_sgx()) {
 		/* OMAP3430, OMAP3525, OMAP3515, OMAP3503 devices */
 		cpu_name = "OMAP3430/3530";
@@ -472,11 +510,11 @@ void __init omap2_check_revision(void)
 	} else if (cpu_is_omap34xx()) {
 		omap3_check_revision(&cpu_rev);
 
-		/* TI816X doesn't have feature register */
-		if (!cpu_is_ti816x())
+		/* TI81XX doesn't have feature register */
+		if (!cpu_is_ti81xx())
 			omap3_check_features();
 		else
-			ti816x_check_features();
+			ti81xx_check_features();
 
 		omap3_cpuinfo(cpu_rev);
 		return;
diff --git a/arch/arm/mach-omap2/include/mach/debug-macro.S b/arch/arm/mach-omap2/include/mach/debug-macro.S
index 13f98e59cfef..cdfc2a1f0e75 100644
--- a/arch/arm/mach-omap2/include/mach/debug-macro.S
+++ b/arch/arm/mach-omap2/include/mach/debug-macro.S
@@ -66,11 +66,11 @@ omap_uart_lsr:	.word	0
 		beq	34f			@ configure OMAP3UART4
 		cmp	\rp, #OMAP4UART4	@ only on 44xx
 		beq	44f			@ configure OMAP4UART4
-		cmp	\rp, #TI816XUART1	@ ti816x UART offsets different
+		cmp	\rp, #TI81XXUART1	@ ti81Xx UART offsets different
 		beq	81f			@ configure UART1
-		cmp	\rp, #TI816XUART2	@ ti816x UART offsets different
+		cmp	\rp, #TI81XXUART2	@ ti81Xx UART offsets different
 		beq	82f			@ configure UART2
-		cmp	\rp, #TI816XUART3	@ ti816x UART offsets different
+		cmp	\rp, #TI81XXUART3	@ ti81Xx UART offsets different
 		beq	83f			@ configure UART3
 		cmp	\rp, #ZOOM_UART		@ only on zoom2/3
 		beq	95f			@ configure ZOOM_UART
@@ -94,11 +94,11 @@ omap_uart_lsr:	.word	0
 		b	98f
 44:		mov	\rp, #UART_OFFSET(OMAP4_UART4_BASE)
 		b	98f
-81:		mov	\rp, #UART_OFFSET(TI816X_UART1_BASE)
+81:		mov	\rp, #UART_OFFSET(TI81XX_UART1_BASE)
 		b	98f
-82:		mov	\rp, #UART_OFFSET(TI816X_UART2_BASE)
+82:		mov	\rp, #UART_OFFSET(TI81XX_UART2_BASE)
 		b	98f
-83:		mov	\rp, #UART_OFFSET(TI816X_UART3_BASE)
+83:		mov	\rp, #UART_OFFSET(TI81XX_UART3_BASE)
 		b	98f
 
 95:		ldr	\rp, =ZOOM_UART_BASE
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 65843390e7f0..3f174d51f67f 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -176,14 +176,31 @@ static struct map_desc omap34xx_io_desc[] __initdata = {
 };
 #endif
 
-#ifdef CONFIG_SOC_OMAPTI816X
-static struct map_desc omapti816x_io_desc[] __initdata = {
+#ifdef CONFIG_SOC_OMAPTI81XX
+static struct map_desc omapti81xx_io_desc[] __initdata = {
+	{
+		.virtual	= L4_34XX_VIRT,
+		.pfn		= __phys_to_pfn(L4_34XX_PHYS),
+		.length		= L4_34XX_SIZE,
+		.type		= MT_DEVICE
+	}
+};
+#endif
+
+#ifdef CONFIG_SOC_OMAPAM33XX
+static struct map_desc omapam33xx_io_desc[] __initdata = {
 	{
 		.virtual	= L4_34XX_VIRT,
 		.pfn		= __phys_to_pfn(L4_34XX_PHYS),
 		.length		= L4_34XX_SIZE,
 		.type		= MT_DEVICE
 	},
+	{
+		.virtual	= L4_WK_AM33XX_VIRT,
+		.pfn		= __phys_to_pfn(L4_WK_AM33XX_PHYS),
+		.length		= L4_WK_AM33XX_SIZE,
+		.type		= MT_DEVICE
+	}
 };
 #endif
 
@@ -272,10 +289,17 @@ void __init omap34xx_map_common_io(void)
 }
 #endif
 
-#ifdef CONFIG_SOC_OMAPTI816X
-void __init omapti816x_map_common_io(void)
+#ifdef CONFIG_SOC_OMAPTI81XX
+void __init omapti81xx_map_common_io(void)
+{
+	iotable_init(omapti81xx_io_desc, ARRAY_SIZE(omapti81xx_io_desc));
+}
+#endif
+
+#ifdef CONFIG_SOC_OMAPAM33XX
+void __init omapam33xx_map_common_io(void)
 {
-	iotable_init(omapti816x_io_desc, ARRAY_SIZE(omapti816x_io_desc));
+	iotable_init(omapam33xx_io_desc, ARRAY_SIZE(omapam33xx_io_desc));
 }
 #endif
 
@@ -427,9 +451,9 @@ void __init am35xx_init_early(void)
 	omap3_init_early();
 }
 
-void __init ti816x_init_early(void)
+void __init ti81xx_init_early(void)
 {
-	omap2_set_globals_ti816x();
+	omap2_set_globals_ti81xx();
 	omap_common_init_early();
 	omap3xxx_voltagedomains_init();
 	omap3xxx_powerdomains_init();
diff --git a/arch/arm/mach-omap2/irq.c b/arch/arm/mach-omap2/irq.c
index 42b1d6591912..1fef061f7927 100644
--- a/arch/arm/mach-omap2/irq.c
+++ b/arch/arm/mach-omap2/irq.c
@@ -193,7 +193,7 @@ void __init omap3_init_irq(void)
 	omap_init_irq(OMAP34XX_IC_BASE, 96);
 }
 
-void __init ti816x_init_irq(void)
+void __init ti81xx_init_irq(void)
 {
 	omap_init_irq(OMAP34XX_IC_BASE, 128);
 }
diff --git a/arch/arm/mach-omap2/opp2xxx.h b/arch/arm/mach-omap2/opp2xxx.h
index 8affc66a92c2..8fae534eb157 100644
--- a/arch/arm/mach-omap2/opp2xxx.h
+++ b/arch/arm/mach-omap2/opp2xxx.h
@@ -51,7 +51,7 @@ struct prcm_config {
 	unsigned long cm_clksel2_pll;	/* dpllx1 or x2 out */
 	unsigned long cm_clksel_mdm;	/* modem dividers 2430 only */
 	unsigned long base_sdrc_rfr;	/* base refresh timing for a set */
-	unsigned char flags;
+	unsigned short flags;
 };
 
 
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index ef8595c80296..b8822f8b2891 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -30,7 +30,6 @@
 #include <linux/irq.h>
 #include <linux/time.h>
 #include <linux/gpio.h>
-#include <linux/console.h>
 
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
@@ -127,27 +126,11 @@ static void omap2_enter_full_retention(void)
 	if (omap_irq_pending())
 		goto no_sleep;
 
-	/* Block console output in case it is on one of the OMAP UARTs */
-	if (!is_suspending())
-		if (!console_trylock())
-			goto no_sleep;
-
-	omap_uart_prepare_idle(0);
-	omap_uart_prepare_idle(1);
-	omap_uart_prepare_idle(2);
-
 	/* Jump to SRAM suspend code */
 	omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
 			   OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
 			   OMAP_SDRC_REGADDR(SDRC_POWER));
 
-	omap_uart_resume_idle(2);
-	omap_uart_resume_idle(1);
-	omap_uart_resume_idle(0);
-
-	if (!is_suspending())
-		console_unlock();
-
 no_sleep:
 	omap2_gpio_resume_after_idle();
 
@@ -239,8 +222,6 @@ static int omap2_can_sleep(void)
 {
 	if (omap2_fclks_active())
 		return 0;
-	if (!omap_uart_can_sleep())
-		return 0;
 	if (osc_ck->usecount > 1)
 		return 0;
 	if (omap_dma_running())
@@ -291,7 +272,6 @@ static int omap2_pm_suspend(void)
 	mir1 = omap_readl(0x480fe0a4);
 	omap_writel(1 << 5, 0x480fe0ac);
 
-	omap_uart_prepare_suspend();
 	omap2_enter_full_retention();
 
 	omap_writel(mir1, 0x480fe0a4);
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 53b5b1a71e0e..fc6987578920 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -28,7 +28,6 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/slab.h>
-#include <linux/console.h>
 #include <trace/events/power.h>
 
 #include <asm/suspend.h>
@@ -36,7 +35,6 @@
 #include <plat/sram.h>
 #include "clockdomain.h"
 #include "powerdomain.h"
-#include <plat/serial.h>
 #include <plat/sdrc.h>
 #include <plat/prcm.h>
 #include <plat/gpmc.h>
@@ -54,15 +52,6 @@
 
 #ifdef CONFIG_SUSPEND
 static suspend_state_t suspend_state = PM_SUSPEND_ON;
-static inline bool is_suspending(void)
-{
-	return (suspend_state != PM_SUSPEND_ON) && console_suspend_enabled;
-}
-#else
-static inline bool is_suspending(void)
-{
-	return false;
-}
 #endif
 
 /* pm34xx errata defined in pm.h */
@@ -337,20 +326,11 @@ void omap_sram_idle(void)
 			omap3_enable_io_chain();
 	}
 
-	/* Block console output in case it is on one of the OMAP UARTs */
-	if (!is_suspending())
-		if (per_next_state < PWRDM_POWER_ON ||
-		    core_next_state < PWRDM_POWER_ON)
-			if (!console_trylock())
-				goto console_still_active;
-
 	pwrdm_pre_transition();
 
 	/* PER */
 	if (per_next_state < PWRDM_POWER_ON) {
 		per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0;
-		omap_uart_prepare_idle(2);
-		omap_uart_prepare_idle(3);
 		omap2_gpio_prepare_for_idle(per_going_off);
 		if (per_next_state == PWRDM_POWER_OFF)
 				omap3_per_save_context();
@@ -358,8 +338,6 @@ void omap_sram_idle(void)
 
 	/* CORE */
 	if (core_next_state < PWRDM_POWER_ON) {
-		omap_uart_prepare_idle(0);
-		omap_uart_prepare_idle(1);
 		if (core_next_state == PWRDM_POWER_OFF) {
 			omap3_core_save_context();
 			omap3_cm_save_context();
@@ -408,8 +386,6 @@ void omap_sram_idle(void)
 			omap3_sram_restore_context();
 			omap2_sms_restore_context();
 		}
-		omap_uart_resume_idle(0);
-		omap_uart_resume_idle(1);
 		if (core_next_state == PWRDM_POWER_OFF)
 			omap2_prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
 					       OMAP3430_GR_MOD,
@@ -425,14 +401,8 @@ void omap_sram_idle(void)
 		omap2_gpio_resume_after_idle();
 		if (per_prev_state == PWRDM_POWER_OFF)
 			omap3_per_restore_context();
-		omap_uart_resume_idle(2);
-		omap_uart_resume_idle(3);
 	}
 
-	if (!is_suspending())
-		console_unlock();
-
-console_still_active:
 	/* Disable IO-PAD and IO-CHAIN wakeup */
 	if (omap3_has_io_wakeup() &&
 	    (per_next_state < PWRDM_POWER_ON ||
@@ -446,21 +416,11 @@ console_still_active:
 	clkdm_allow_idle(mpu_pwrdm->pwrdm_clkdms[0]);
 }
 
-int omap3_can_sleep(void)
-{
-	if (!omap_uart_can_sleep())
-		return 0;
-	return 1;
-}
-
 static void omap3_pm_idle(void)
 {
 	local_irq_disable();
 	local_fiq_disable();
 
-	if (!omap3_can_sleep())
-		goto out;
-
 	if (omap_irq_pending() || need_resched())
 		goto out;
 
@@ -494,7 +454,6 @@ static int omap3_pm_suspend(void)
 			goto restore;
 	}
 
-	omap_uart_prepare_suspend();
 	omap3_intc_suspend();
 
 	omap_sram_idle();
@@ -541,7 +500,6 @@ static int omap3_pm_begin(suspend_state_t state)
 {
 	disable_hlt();
 	suspend_state = state;
-	omap_uart_enable_irqs(0);
 	omap_prcm_irq_prepare();
 	return 0;
 }
@@ -549,7 +507,6 @@ static int omap3_pm_begin(suspend_state_t state)
 static void omap3_pm_end(void)
 {
 	suspend_state = PM_SUSPEND_ON;
-	omap_uart_enable_irqs(1);
 	enable_hlt();
 	return;
 }
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 42c326732a29..247d89478f24 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -19,26 +19,21 @@
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/serial_reg.h>
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/serial_8250.h>
 #include <linux/pm_runtime.h>
 #include <linux/console.h>
 
-#ifdef CONFIG_SERIAL_OMAP
 #include <plat/omap-serial.h>
-#endif
-
 #include "common.h"
 #include <plat/board.h>
-#include <plat/clock.h>
 #include <plat/dma.h>
 #include <plat/omap_hwmod.h>
 #include <plat/omap_device.h>
+#include <plat/omap-pm.h>
 
 #include "prm2xxx_3xxx.h"
 #include "pm.h"
@@ -47,603 +42,226 @@
 #include "control.h"
 #include "mux.h"
 
-#define UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV	0x52
-#define UART_OMAP_WER		0x17	/* Wake-up enable register */
-
-#define UART_ERRATA_FIFO_FULL_ABORT	(0x1 << 0)
-#define UART_ERRATA_i202_MDR1_ACCESS	(0x1 << 1)
-
 /*
- * NOTE: By default the serial timeout is disabled as it causes lost characters
- * over the serial ports. This means that the UART clocks will stay on until
- * disabled via sysfs. This also causes that any deeper omap sleep states are
- * blocked. 
+ * NOTE: By default the serial auto_suspend timeout is disabled as it causes
+ * lost characters over the serial ports. This means that the UART clocks will
+ * stay on until power/autosuspend_delay is set for the uart from sysfs.
+ * This also causes that any deeper omap sleep states are blocked.
  */
-#define DEFAULT_TIMEOUT 0
+#define DEFAULT_AUTOSUSPEND_DELAY	-1
 
 #define MAX_UART_HWMOD_NAME_LEN		16
 
 struct omap_uart_state {
 	int num;
 	int can_sleep;
-	struct timer_list timer;
-	u32 timeout;
-
-	void __iomem *wk_st;
-	void __iomem *wk_en;
-	u32 wk_mask;
-	u32 padconf;
-	u32 dma_enabled;
-
-	struct clk *ick;
-	struct clk *fck;
-	int clocked;
-
-	int irq;
-	int regshift;
-	int irqflags;
-	void __iomem *membase;
-	resource_size_t mapbase;
 
 	struct list_head node;
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
-
-	u32 errata;
-#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
-	int context_valid;
-
-	/* Registers to be saved/restored for OFF-mode */
-	u16 dll;
-	u16 dlh;
-	u16 ier;
-	u16 sysc;
-	u16 scr;
-	u16 wer;
-	u16 mcr;
-#endif
 };
 
 static LIST_HEAD(uart_list);
 static u8 num_uarts;
+static u8 console_uart_id = -1;
+static u8 no_console_suspend;
+static u8 uart_debug;
+
+#define DEFAULT_RXDMA_POLLRATE		1	/* RX DMA polling rate (us) */
+#define DEFAULT_RXDMA_BUFSIZE		4096	/* RX DMA buffer size */
+#define DEFAULT_RXDMA_TIMEOUT		(3 * HZ)/* RX DMA timeout (jiffies) */
+
+static struct omap_uart_port_info omap_serial_default_info[] __initdata = {
+	{
+		.dma_enabled	= false,
+		.dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
+		.dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
+		.dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
+		.autosuspend_timeout = DEFAULT_AUTOSUSPEND_DELAY,
+	},
+};
 
-static inline unsigned int __serial_read_reg(struct uart_port *up,
-					     int offset)
-{
-	offset <<= up->regshift;
-	return (unsigned int)__raw_readb(up->membase + offset);
-}
-
-static inline unsigned int serial_read_reg(struct omap_uart_state *uart,
-					   int offset)
+#ifdef CONFIG_PM
+static void omap_uart_enable_wakeup(struct platform_device *pdev, bool enable)
 {
-	offset <<= uart->regshift;
-	return (unsigned int)__raw_readb(uart->membase + offset);
-}
+	struct omap_device *od = to_omap_device(pdev);
 
-static inline void __serial_write_reg(struct uart_port *up, int offset,
-		int value)
-{
-	offset <<= up->regshift;
-	__raw_writeb(value, up->membase + offset);
-}
+	if (!od)
+		return;
 
-static inline void serial_write_reg(struct omap_uart_state *uart, int offset,
-				    int value)
-{
-	offset <<= uart->regshift;
-	__raw_writeb(value, uart->membase + offset);
+	if (enable)
+		omap_hwmod_enable_wakeup(od->hwmods[0]);
+	else
+		omap_hwmod_disable_wakeup(od->hwmods[0]);
 }
 
 /*
- * Internal UARTs need to be initialized for the 8250 autoconfig to work
- * properly. Note that the TX watermark initialization may not be needed
- * once the 8250.c watermark handling code is merged.
+ * Errata i291: [UART]:Cannot Acknowledge Idle Requests
+ * in Smartidle Mode When Configured for DMA Operations.
+ * WA: configure uart in force idle mode.
  */
-
-static inline void __init omap_uart_reset(struct omap_uart_state *uart)
+static void omap_uart_set_noidle(struct platform_device *pdev)
 {
-	serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
-	serial_write_reg(uart, UART_OMAP_SCR, 0x08);
-	serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE);
-}
-
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
+	struct omap_device *od = to_omap_device(pdev);
 
-/*
- * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6)
- * The access to uart register after MDR1 Access
- * causes UART to corrupt data.
- *
- * Need a delay =
- * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
- * give 10 times as much
- */
-static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
-		u8 fcr_val)
-{
-	u8 timeout = 255;
-
-	serial_write_reg(uart, UART_OMAP_MDR1, mdr1_val);
-	udelay(2);
-	serial_write_reg(uart, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT |
-			UART_FCR_CLEAR_RCVR);
-	/*
-	 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
-	 * TX_FIFO_E bit is 1.
-	 */
-	while (UART_LSR_THRE != (serial_read_reg(uart, UART_LSR) &
-				(UART_LSR_THRE | UART_LSR_DR))) {
-		timeout--;
-		if (!timeout) {
-			/* Should *never* happen. we warn and carry on */
-			dev_crit(&uart->pdev->dev, "Errata i202: timedout %x\n",
-			serial_read_reg(uart, UART_LSR));
-			break;
-		}
-		udelay(1);
-	}
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
 }
 
-static void omap_uart_save_context(struct omap_uart_state *uart)
+static void omap_uart_set_forceidle(struct platform_device *pdev)
 {
-	u16 lcr = 0;
+	struct omap_device *od = to_omap_device(pdev);
 
-	if (!enable_off_mode)
-		return;
-
-	lcr = serial_read_reg(uart, UART_LCR);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	uart->dll = serial_read_reg(uart, UART_DLL);
-	uart->dlh = serial_read_reg(uart, UART_DLM);
-	serial_write_reg(uart, UART_LCR, lcr);
-	uart->ier = serial_read_reg(uart, UART_IER);
-	uart->sysc = serial_read_reg(uart, UART_OMAP_SYSC);
-	uart->scr = serial_read_reg(uart, UART_OMAP_SCR);
-	uart->wer = serial_read_reg(uart, UART_OMAP_WER);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_A);
-	uart->mcr = serial_read_reg(uart, UART_MCR);
-	serial_write_reg(uart, UART_LCR, lcr);
-
-	uart->context_valid = 1;
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_FORCE);
 }
 
-static void omap_uart_restore_context(struct omap_uart_state *uart)
-{
-	u16 efr = 0;
-
-	if (!enable_off_mode)
-		return;
-
-	if (!uart->context_valid)
-		return;
-
-	uart->context_valid = 0;
-
-	if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
-		omap_uart_mdr1_errataset(uart, UART_OMAP_MDR1_DISABLE, 0xA0);
-	else
-		serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
-
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	efr = serial_read_reg(uart, UART_EFR);
-	serial_write_reg(uart, UART_EFR, UART_EFR_ECB);
-	serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
-	serial_write_reg(uart, UART_IER, 0x0);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_write_reg(uart, UART_DLL, uart->dll);
-	serial_write_reg(uart, UART_DLM, uart->dlh);
-	serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
-	serial_write_reg(uart, UART_IER, uart->ier);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_A);
-	serial_write_reg(uart, UART_MCR, uart->mcr);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_write_reg(uart, UART_EFR, efr);
-	serial_write_reg(uart, UART_LCR, UART_LCR_WLEN8);
-	serial_write_reg(uart, UART_OMAP_SCR, uart->scr);
-	serial_write_reg(uart, UART_OMAP_WER, uart->wer);
-	serial_write_reg(uart, UART_OMAP_SYSC, uart->sysc);
-
-	if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
-		omap_uart_mdr1_errataset(uart, UART_OMAP_MDR1_16X_MODE, 0xA1);
-	else
-		/* UART 16x mode */
-		serial_write_reg(uart, UART_OMAP_MDR1,
-				UART_OMAP_MDR1_16X_MODE);
-}
 #else
-static inline void omap_uart_save_context(struct omap_uart_state *uart) {}
-static inline void omap_uart_restore_context(struct omap_uart_state *uart) {}
-#endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */
-
-static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)
-{
-	if (uart->clocked)
-		return;
-
-	omap_device_enable(uart->pdev);
-	uart->clocked = 1;
-	omap_uart_restore_context(uart);
-}
-
-#ifdef CONFIG_PM
-
-static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
-{
-	if (!uart->clocked)
-		return;
-
-	omap_uart_save_context(uart);
-	uart->clocked = 0;
-	omap_device_idle(uart->pdev);
-}
-
-static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
-{
-	/* Set wake-enable bit */
-	if (uart->wk_en && uart->wk_mask) {
-		u32 v = __raw_readl(uart->wk_en);
-		v |= uart->wk_mask;
-		__raw_writel(v, uart->wk_en);
-	}
-
-	/* Ensure IOPAD wake-enables are set */
-	if (cpu_is_omap34xx() && uart->padconf) {
-		u16 v = omap_ctrl_readw(uart->padconf);
-		v |= OMAP3_PADCONF_WAKEUPENABLE0;
-		omap_ctrl_writew(v, uart->padconf);
-	}
-}
-
-static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
-{
-	/* Clear wake-enable bit */
-	if (uart->wk_en && uart->wk_mask) {
-		u32 v = __raw_readl(uart->wk_en);
-		v &= ~uart->wk_mask;
-		__raw_writel(v, uart->wk_en);
-	}
-
-	/* Ensure IOPAD wake-enables are cleared */
-	if (cpu_is_omap34xx() && uart->padconf) {
-		u16 v = omap_ctrl_readw(uart->padconf);
-		v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
-		omap_ctrl_writew(v, uart->padconf);
-	}
-}
-
-static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
-					       int enable)
-{
-	u8 idlemode;
-
-	if (enable) {
-		/**
-		 * Errata 2.15: [UART]:Cannot Acknowledge Idle Requests
-		 * in Smartidle Mode When Configured for DMA Operations.
-		 */
-		if (uart->dma_enabled)
-			idlemode = HWMOD_IDLEMODE_FORCE;
-		else
-			idlemode = HWMOD_IDLEMODE_SMART;
-	} else {
-		idlemode = HWMOD_IDLEMODE_NO;
-	}
-
-	omap_hwmod_set_slave_idlemode(uart->oh, idlemode);
-}
-
-static void omap_uart_block_sleep(struct omap_uart_state *uart)
-{
-	omap_uart_enable_clocks(uart);
-
-	omap_uart_smart_idle_enable(uart, 0);
-	uart->can_sleep = 0;
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	else
-		del_timer(&uart->timer);
-}
-
-static void omap_uart_allow_sleep(struct omap_uart_state *uart)
-{
-	if (device_may_wakeup(&uart->pdev->dev))
-		omap_uart_enable_wakeup(uart);
-	else
-		omap_uart_disable_wakeup(uart);
-
-	if (!uart->clocked)
-		return;
-
-	omap_uart_smart_idle_enable(uart, 1);
-	uart->can_sleep = 1;
-	del_timer(&uart->timer);
-}
-
-static void omap_uart_idle_timer(unsigned long data)
-{
-	struct omap_uart_state *uart = (struct omap_uart_state *)data;
-
-	omap_uart_allow_sleep(uart);
-}
-
-void omap_uart_prepare_idle(int num)
-{
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (num == uart->num && uart->can_sleep) {
-			omap_uart_disable_clocks(uart);
-			return;
-		}
-	}
-}
-
-void omap_uart_resume_idle(int num)
-{
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (num == uart->num && uart->can_sleep) {
-			omap_uart_enable_clocks(uart);
-
-			/* Check for IO pad wakeup */
-			if (cpu_is_omap34xx() && uart->padconf) {
-				u16 p = omap_ctrl_readw(uart->padconf);
-
-				if (p & OMAP3_PADCONF_WAKEUPEVENT0)
-					omap_uart_block_sleep(uart);
-			}
-
-			/* Check for normal UART wakeup */
-			if (__raw_readl(uart->wk_st) & uart->wk_mask)
-				omap_uart_block_sleep(uart);
-			return;
-		}
-	}
-}
-
-void omap_uart_prepare_suspend(void)
-{
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		omap_uart_allow_sleep(uart);
-	}
-}
-
-int omap_uart_can_sleep(void)
-{
-	struct omap_uart_state *uart;
-	int can_sleep = 1;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (!uart->clocked)
-			continue;
-
-		if (!uart->can_sleep) {
-			can_sleep = 0;
-			continue;
-		}
-
-		/* This UART can now safely sleep. */
-		omap_uart_allow_sleep(uart);
-	}
-
-	return can_sleep;
-}
+static void omap_uart_enable_wakeup(struct platform_device *pdev, bool enable)
+{}
+static void omap_uart_set_noidle(struct platform_device *pdev) {}
+static void omap_uart_set_forceidle(struct platform_device *pdev) {}
+#endif /* CONFIG_PM */
 
-/**
- * omap_uart_interrupt()
- *
- * This handler is used only to detect that *any* UART interrupt has
- * occurred.  It does _nothing_ to handle the interrupt.  Rather,
- * any UART interrupt will trigger the inactivity timer so the
- * UART will not idle or sleep for its timeout period.
- *
- **/
-/* static int first_interrupt; */
-static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
-{
-	struct omap_uart_state *uart = dev_id;
+#ifdef CONFIG_OMAP_MUX
+static struct omap_device_pad default_uart1_pads[] __initdata = {
+	{
+		.name	= "uart1_cts.uart1_cts",
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart1_rts.uart1_rts",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart1_tx.uart1_tx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart1_rx.uart1_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+};
 
-	omap_uart_block_sleep(uart);
+static struct omap_device_pad default_uart2_pads[] __initdata = {
+	{
+		.name	= "uart2_cts.uart2_cts",
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart2_rts.uart2_rts",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart2_tx.uart2_tx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart2_rx.uart2_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+};
 
-	return IRQ_NONE;
-}
+static struct omap_device_pad default_uart3_pads[] __initdata = {
+	{
+		.name	= "uart3_cts_rctx.uart3_cts_rctx",
+		.enable	= OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart3_rts_sd.uart3_rts_sd",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart3_tx_irtx.uart3_tx_irtx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart3_rx_irrx.uart3_rx_irrx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+	},
+};
 
-static void omap_uart_idle_init(struct omap_uart_state *uart)
-{
-	int ret;
-
-	uart->can_sleep = 0;
-	uart->timeout = DEFAULT_TIMEOUT;
-	setup_timer(&uart->timer, omap_uart_idle_timer,
-		    (unsigned long) uart);
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	omap_uart_smart_idle_enable(uart, 0);
-
-	if (cpu_is_omap34xx() && !cpu_is_ti816x()) {
-		u32 mod = (uart->num > 1) ? OMAP3430_PER_MOD : CORE_MOD;
-		u32 wk_mask = 0;
-		u32 padconf = 0;
-
-		/* XXX These PRM accesses do not belong here */
-		uart->wk_en = OMAP34XX_PRM_REGADDR(mod, PM_WKEN1);
-		uart->wk_st = OMAP34XX_PRM_REGADDR(mod, PM_WKST1);
-		switch (uart->num) {
-		case 0:
-			wk_mask = OMAP3430_ST_UART1_MASK;
-			padconf = 0x182;
-			break;
-		case 1:
-			wk_mask = OMAP3430_ST_UART2_MASK;
-			padconf = 0x17a;
-			break;
-		case 2:
-			wk_mask = OMAP3430_ST_UART3_MASK;
-			padconf = 0x19e;
-			break;
-		case 3:
-			wk_mask = OMAP3630_ST_UART4_MASK;
-			padconf = 0x0d2;
-			break;
-		}
-		uart->wk_mask = wk_mask;
-		uart->padconf = padconf;
-	} else if (cpu_is_omap24xx()) {
-		u32 wk_mask = 0;
-		u32 wk_en = PM_WKEN1, wk_st = PM_WKST1;
-
-		switch (uart->num) {
-		case 0:
-			wk_mask = OMAP24XX_ST_UART1_MASK;
-			break;
-		case 1:
-			wk_mask = OMAP24XX_ST_UART2_MASK;
-			break;
-		case 2:
-			wk_en = OMAP24XX_PM_WKEN2;
-			wk_st = OMAP24XX_PM_WKST2;
-			wk_mask = OMAP24XX_ST_UART3_MASK;
-			break;
-		}
-		uart->wk_mask = wk_mask;
-		if (cpu_is_omap2430()) {
-			uart->wk_en = OMAP2430_PRM_REGADDR(CORE_MOD, wk_en);
-			uart->wk_st = OMAP2430_PRM_REGADDR(CORE_MOD, wk_st);
-		} else if (cpu_is_omap2420()) {
-			uart->wk_en = OMAP2420_PRM_REGADDR(CORE_MOD, wk_en);
-			uart->wk_st = OMAP2420_PRM_REGADDR(CORE_MOD, wk_st);
-		}
-	} else {
-		uart->wk_en = NULL;
-		uart->wk_st = NULL;
-		uart->wk_mask = 0;
-		uart->padconf = 0;
-	}
+static struct omap_device_pad default_omap36xx_uart4_pads[] __initdata = {
+	{
+		.name   = "gpmc_wait2.uart4_tx",
+		.enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "gpmc_wait3.uart4_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT | OMAP_MUX_MODE2,
+		.idle	= OMAP_PIN_INPUT | OMAP_MUX_MODE2,
+	},
+};
 
-	uart->irqflags |= IRQF_SHARED;
-	ret = request_threaded_irq(uart->irq, NULL, omap_uart_interrupt,
-				   IRQF_SHARED, "serial idle", (void *)uart);
-	WARN_ON(ret);
-}
+static struct omap_device_pad default_omap4_uart4_pads[] __initdata = {
+	{
+		.name	= "uart4_tx.uart4_tx",
+		.enable	= OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+	},
+	{
+		.name	= "uart4_rx.uart4_rx",
+		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+		.enable	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+		.idle	= OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+	},
+};
 
-void omap_uart_enable_irqs(int enable)
+static void omap_serial_fill_default_pads(struct omap_board_data *bdata)
 {
-	int ret;
-	struct omap_uart_state *uart;
-
-	list_for_each_entry(uart, &uart_list, node) {
-		if (enable) {
-			pm_runtime_put_sync(&uart->pdev->dev);
-			ret = request_threaded_irq(uart->irq, NULL,
-						   omap_uart_interrupt,
-						   IRQF_SHARED,
-						   "serial idle",
-						   (void *)uart);
-		} else {
-			pm_runtime_get_noresume(&uart->pdev->dev);
-			free_irq(uart->irq, (void *)uart);
+	switch (bdata->id) {
+	case 0:
+		bdata->pads = default_uart1_pads;
+		bdata->pads_cnt = ARRAY_SIZE(default_uart1_pads);
+		break;
+	case 1:
+		bdata->pads = default_uart2_pads;
+		bdata->pads_cnt = ARRAY_SIZE(default_uart2_pads);
+		break;
+	case 2:
+		bdata->pads = default_uart3_pads;
+		bdata->pads_cnt = ARRAY_SIZE(default_uart3_pads);
+		break;
+	case 3:
+		if (cpu_is_omap44xx()) {
+			bdata->pads = default_omap4_uart4_pads;
+			bdata->pads_cnt =
+				ARRAY_SIZE(default_omap4_uart4_pads);
+		} else if (cpu_is_omap3630()) {
+			bdata->pads = default_omap36xx_uart4_pads;
+			bdata->pads_cnt =
+				ARRAY_SIZE(default_omap36xx_uart4_pads);
 		}
+		break;
+	default:
+		break;
 	}
 }
-
-static ssize_t sleep_timeout_show(struct device *dev,
-				  struct device_attribute *attr,
-				  char *buf)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *odev = to_omap_device(pdev);
-	struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
-
-	return sprintf(buf, "%u\n", uart->timeout / HZ);
-}
-
-static ssize_t sleep_timeout_store(struct device *dev,
-				   struct device_attribute *attr,
-				   const char *buf, size_t n)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *odev = to_omap_device(pdev);
-	struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
-	unsigned int value;
-
-	if (sscanf(buf, "%u", &value) != 1) {
-		dev_err(dev, "sleep_timeout_store: Invalid value\n");
-		return -EINVAL;
-	}
-
-	uart->timeout = value * HZ;
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	else
-		/* A zero value means disable timeout feature */
-		omap_uart_block_sleep(uart);
-
-	return n;
-}
-
-static DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show,
-		sleep_timeout_store);
-#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
 #else
-static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
-static void omap_uart_block_sleep(struct omap_uart_state *uart)
-{
-	/* Needed to enable UART clocks when built without CONFIG_PM */
-	omap_uart_enable_clocks(uart);
-}
-#define DEV_CREATE_FILE(dev, attr)
-#endif /* CONFIG_PM */
-
-#ifndef CONFIG_SERIAL_OMAP
-/*
- * Override the default 8250 read handler: mem_serial_in()
- * Empty RX fifo read causes an abort on omap3630 and omap4
- * This function makes sure that an empty rx fifo is not read on these silicons
- * (OMAP1/2/3430 are not affected)
- */
-static unsigned int serial_in_override(struct uart_port *up, int offset)
-{
-	if (UART_RX == offset) {
-		unsigned int lsr;
-		lsr = __serial_read_reg(up, UART_LSR);
-		if (!(lsr & UART_LSR_DR))
-			return -EPERM;
-	}
-
-	return __serial_read_reg(up, offset);
-}
+static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {}
+#endif
 
-static void serial_out_override(struct uart_port *up, int offset, int value)
+char *cmdline_find_option(char *str)
 {
-	unsigned int status, tmout = 10000;
+	extern char *saved_command_line;
 
-	status = __serial_read_reg(up, UART_LSR);
-	while (!(status & UART_LSR_THRE)) {
-		/* Wait up to 10ms for the character(s) to be sent. */
-		if (--tmout == 0)
-			break;
-		udelay(1);
-		status = __serial_read_reg(up, UART_LSR);
-	}
-	__serial_write_reg(up, offset, value);
+	return strstr(saved_command_line, str);
 }
-#endif
 
 static int __init omap_serial_early_init(void)
 {
-	int i = 0;
-
 	do {
 		char oh_name[MAX_UART_HWMOD_NAME_LEN];
 		struct omap_hwmod *oh;
 		struct omap_uart_state *uart;
+		char uart_name[MAX_UART_HWMOD_NAME_LEN];
 
 		snprintf(oh_name, MAX_UART_HWMOD_NAME_LEN,
-			 "uart%d", i + 1);
+			 "uart%d", num_uarts + 1);
 		oh = omap_hwmod_lookup(oh_name);
 		if (!oh)
 			break;
@@ -653,21 +271,35 @@ static int __init omap_serial_early_init(void)
 			return -ENODEV;
 
 		uart->oh = oh;
-		uart->num = i++;
+		uart->num = num_uarts++;
 		list_add_tail(&uart->node, &uart_list);
-		num_uarts++;
-
-		/*
-		 * NOTE: omap_hwmod_setup*() has not yet been called,
-		 *       so no hwmod functions will work yet.
-		 */
-
-		/*
-		 * During UART early init, device need to be probed
-		 * to determine SoC specific init before omap_device
-		 * is ready.  Therefore, don't allow idle here
-		 */
-		uart->oh->flags |= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET;
+		snprintf(uart_name, MAX_UART_HWMOD_NAME_LEN,
+				"%s%d", OMAP_SERIAL_NAME, uart->num);
+
+		if (cmdline_find_option(uart_name)) {
+			console_uart_id = uart->num;
+
+			if (console_loglevel >= 10) {
+				uart_debug = true;
+				pr_info("%s used as console in debug mode"
+						" uart%d clocks will not be"
+						" gated", uart_name, uart->num);
+			}
+
+			if (cmdline_find_option("no_console_suspend"))
+				no_console_suspend = true;
+
+			/*
+			 * omap-uart can be used for earlyprintk logs
+			 * So if omap-uart is used as console then prevent
+			 * uart reset and idle to get logs from omap-uart
+			 * until uart console driver is available to take
+			 * care for console messages.
+			 * Idling or resetting omap-uart while printing logs
+			 * early boot logs can stall the boot-up.
+			 */
+			oh->flags |= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET;
+		}
 	} while (1);
 
 	return 0;
@@ -677,6 +309,7 @@ core_initcall(omap_serial_early_init);
 /**
  * omap_serial_init_port() - initialize single serial port
  * @bdata: port specific board data pointer
+ * @info: platform specific data pointer
  *
  * This function initialies serial driver for given port only.
  * Platforms can call this function instead of omap_serial_init()
@@ -685,7 +318,8 @@ core_initcall(omap_serial_early_init);
  * Don't mix calls to omap_serial_init_port() and omap_serial_init(),
  * use only one of the two.
  */
-void __init omap_serial_init_port(struct omap_board_data *bdata)
+void __init omap_serial_init_port(struct omap_board_data *bdata,
+			struct omap_uart_port_info *info)
 {
 	struct omap_uart_state *uart;
 	struct omap_hwmod *oh;
@@ -693,15 +327,7 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	void *pdata = NULL;
 	u32 pdata_size = 0;
 	char *name;
-#ifndef CONFIG_SERIAL_OMAP
-	struct plat_serial8250_port ports[2] = {
-		{},
-		{.flags = 0},
-	};
-	struct plat_serial8250_port *p = &ports[0];
-#else
 	struct omap_uart_port_info omap_up;
-#endif
 
 	if (WARN_ON(!bdata))
 		return;
@@ -713,66 +339,34 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	list_for_each_entry(uart, &uart_list, node)
 		if (bdata->id == uart->num)
 			break;
+	if (!info)
+		info = omap_serial_default_info;
 
 	oh = uart->oh;
-	uart->dma_enabled = 0;
-#ifndef CONFIG_SERIAL_OMAP
-	name = "serial8250";
-
-	/*
-	 * !! 8250 driver does not use standard IORESOURCE* It
-	 * has it's own custom pdata that can be taken from
-	 * the hwmod resource data.  But, this needs to be
-	 * done after the build.
-	 *
-	 * ?? does it have to be done before the register ??
-	 * YES, because platform_device_data_add() copies
-	 * pdata, it does not use a pointer.
-	 */
-	p->flags = UPF_BOOT_AUTOCONF;
-	p->iotype = UPIO_MEM;
-	p->regshift = 2;
-	p->uartclk = OMAP24XX_BASE_BAUD * 16;
-	p->irq = oh->mpu_irqs[0].irq;
-	p->mapbase = oh->slaves[0]->addr->pa_start;
-	p->membase = omap_hwmod_get_mpu_rt_va(oh);
-	p->irqflags = IRQF_SHARED;
-	p->private_data = uart;
-
-	/*
-	 * omap44xx, ti816x: Never read empty UART fifo
-	 * omap3xxx: Never read empty UART fifo on UARTs
-	 * with IP rev >=0x52
-	 */
-	uart->regshift = p->regshift;
-	uart->membase = p->membase;
-	if (cpu_is_omap44xx() || cpu_is_ti816x())
-		uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
-	else if ((serial_read_reg(uart, UART_OMAP_MVER) & 0xFF)
-			>= UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV)
-		uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
-
-	if (uart->errata & UART_ERRATA_FIFO_FULL_ABORT) {
-		p->serial_in = serial_in_override;
-		p->serial_out = serial_out_override;
-	}
-
-	pdata = &ports[0];
-	pdata_size = 2 * sizeof(struct plat_serial8250_port);
-#else
-
 	name = DRIVER_NAME;
 
-	omap_up.dma_enabled = uart->dma_enabled;
+	omap_up.dma_enabled = info->dma_enabled;
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
-	omap_up.mapbase = oh->slaves[0]->addr->pa_start;
-	omap_up.membase = omap_hwmod_get_mpu_rt_va(oh);
-	omap_up.irqflags = IRQF_SHARED;
-	omap_up.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+	omap_up.flags = UPF_BOOT_AUTOCONF;
+	omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
+	omap_up.set_forceidle = omap_uart_set_forceidle;
+	omap_up.set_noidle = omap_uart_set_noidle;
+	omap_up.enable_wakeup = omap_uart_enable_wakeup;
+	omap_up.dma_rx_buf_size = info->dma_rx_buf_size;
+	omap_up.dma_rx_timeout = info->dma_rx_timeout;
+	omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
+	omap_up.autosuspend_timeout = info->autosuspend_timeout;
+
+	/* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
+	if (!cpu_is_omap2420() && !cpu_is_ti816x())
+		omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
+
+	/* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
+	if (cpu_is_omap34xx() || cpu_is_omap3630())
+		omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);
-#endif
 
 	if (WARN_ON(!oh))
 		return;
@@ -782,64 +376,29 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	WARN(IS_ERR(pdev), "Could not build omap_device for %s: %s.\n",
 	     name, oh->name);
 
-	omap_device_disable_idle_on_suspend(pdev);
+	if ((console_uart_id == bdata->id) && no_console_suspend)
+		omap_device_disable_idle_on_suspend(pdev);
+
 	oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
 
-	uart->irq = oh->mpu_irqs[0].irq;
-	uart->regshift = 2;
-	uart->mapbase = oh->slaves[0]->addr->pa_start;
-	uart->membase = omap_hwmod_get_mpu_rt_va(oh);
 	uart->pdev = pdev;
 
 	oh->dev_attr = uart;
 
-	console_lock(); /* in case the earlycon is on the UART */
-
-	/*
-	 * Because of early UART probing, UART did not get idled
-	 * on init.  Now that omap_device is ready, ensure full idle
-	 * before doing omap_device_enable().
-	 */
-	omap_hwmod_idle(uart->oh);
-
-	omap_device_enable(uart->pdev);
-	omap_uart_idle_init(uart);
-	omap_uart_reset(uart);
-	omap_hwmod_enable_wakeup(uart->oh);
-	omap_device_idle(uart->pdev);
-
-	/*
-	 * Need to block sleep long enough for interrupt driven
-	 * driver to start.  Console driver is in polling mode
-	 * so device needs to be kept enabled while polling driver
-	 * is in use.
-	 */
-	if (uart->timeout)
-		uart->timeout = (30 * HZ);
-	omap_uart_block_sleep(uart);
-	uart->timeout = DEFAULT_TIMEOUT;
-
-	console_unlock();
-
-	if ((cpu_is_omap34xx() && uart->padconf) ||
-	    (uart->wk_en && uart->wk_mask)) {
+	if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads)
+			&& !uart_debug)
 		device_init_wakeup(&pdev->dev, true);
-		DEV_CREATE_FILE(&pdev->dev, &dev_attr_sleep_timeout);
-	}
-
-	/* Enable the MDR1 errata for OMAP3 */
-	if (cpu_is_omap34xx() && !cpu_is_ti816x())
-		uart->errata |= UART_ERRATA_i202_MDR1_ACCESS;
 }
 
 /**
- * omap_serial_init() - initialize all supported serial ports
+ * omap_serial_board_init() - initialize all supported serial ports
+ * @info: platform specific data pointer
  *
  * Initializes all available UARTs as serial ports. Platforms
  * can call this function when they want to have default behaviour
  * for serial ports (e.g initialize them all as serial ports).
  */
-void __init omap_serial_init(void)
+void __init omap_serial_board_init(struct omap_uart_port_info *info)
 {
 	struct omap_uart_state *uart;
 	struct omap_board_data bdata;
@@ -849,7 +408,25 @@ void __init omap_serial_init(void)
 		bdata.flags = 0;
 		bdata.pads = NULL;
 		bdata.pads_cnt = 0;
-		omap_serial_init_port(&bdata);
 
+		if (cpu_is_omap44xx() || cpu_is_omap34xx())
+			omap_serial_fill_default_pads(&bdata);
+
+		if (!info)
+			omap_serial_init_port(&bdata, NULL);
+		else
+			omap_serial_init_port(&bdata, &info[uart->num]);
 	}
 }
+
+/**
+ * omap_serial_init() - initialize all supported serial ports
+ *
+ * Initializes all available UARTs.
+ * Platforms can call this function when they want to have default behaviour
+ * for serial ports (e.g initialize them all as serial ports).
+ */
+void __init omap_serial_init(void)
+{
+	omap_serial_board_init(NULL);
+}
diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile
index 3df04d944e4d..9a584614e7e6 100644
--- a/arch/arm/plat-omap/Makefile
+++ b/arch/arm/plat-omap/Makefile
@@ -19,7 +19,6 @@ obj-$(CONFIG_ARCH_OMAP4) += omap_device.o
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 
-obj-$(CONFIG_CPU_FREQ) += cpu-omap.o
 obj-$(CONFIG_OMAP_DM_TIMER) += dmtimer.o
 obj-$(CONFIG_OMAP_DEBUG_DEVICES) += debug-devices.o
 obj-$(CONFIG_OMAP_DEBUG_LEDS) += debug-leds.o
diff --git a/arch/arm/plat-omap/include/plat/am33xx.h b/arch/arm/plat-omap/include/plat/am33xx.h
new file mode 100644
index 000000000000..06c19bb7bca6
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/am33xx.h
@@ -0,0 +1,25 @@
+/*
+ * This file contains the address info for various AM33XX modules.
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc. - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_AM33XX_H
+#define __ASM_ARCH_AM33XX_H
+
+#define L4_SLOW_AM33XX_BASE	0x48000000
+
+#define AM33XX_SCM_BASE		0x44E10000
+#define AM33XX_CTRL_BASE	AM33XX_SCM_BASE
+#define AM33XX_PRCM_BASE	0x44E00000
+
+#endif /* __ASM_ARCH_AM33XX_H */
diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h
index eb73ab40e955..240a7b9fd946 100644
--- a/arch/arm/plat-omap/include/plat/clock.h
+++ b/arch/arm/plat-omap/include/plat/clock.h
@@ -59,6 +59,8 @@ struct clkops {
 #define RATE_IN_4430		(1 << 5)
 #define RATE_IN_TI816X		(1 << 6)
 #define RATE_IN_4460		(1 << 7)
+#define RATE_IN_AM33XX		(1 << 8)
+#define RATE_IN_TI814X		(1 << 9)
 
 #define RATE_IN_24XX		(RATE_IN_242X | RATE_IN_243X)
 #define RATE_IN_34XX		(RATE_IN_3430ES1 | RATE_IN_3430ES2PLUS)
@@ -84,7 +86,7 @@ struct clkops {
 struct clksel_rate {
 	u32			val;
 	u8			div;
-	u8			flags;
+	u16			flags;
 };
 
 /**
diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h
index 408a12f79205..6b51086fce18 100644
--- a/arch/arm/plat-omap/include/plat/cpu.h
+++ b/arch/arm/plat-omap/include/plat/cpu.h
@@ -69,6 +69,7 @@ unsigned int omap_rev(void);
  * cpu_is_omap343x():	True for OMAP3430
  * cpu_is_omap443x():	True for OMAP4430
  * cpu_is_omap446x():	True for OMAP4460
+ * cpu_is_omap447x():	True for OMAP4470
  */
 #define GET_OMAP_CLASS	(omap_rev() & 0xff)
 
@@ -78,6 +79,22 @@ static inline int is_omap ##class (void)		\
 	return (GET_OMAP_CLASS == (id)) ? 1 : 0;	\
 }
 
+#define GET_AM_CLASS	((omap_rev() >> 24) & 0xff)
+
+#define IS_AM_CLASS(class, id)				\
+static inline int is_am ##class (void)			\
+{							\
+	return (GET_AM_CLASS == (id)) ? 1 : 0;		\
+}
+
+#define GET_TI_CLASS	((omap_rev() >> 24) & 0xff)
+
+#define IS_TI_CLASS(class, id)			\
+static inline int is_ti ##class (void)		\
+{							\
+	return (GET_TI_CLASS == (id)) ? 1 : 0;	\
+}
+
 #define GET_OMAP_SUBCLASS	((omap_rev() >> 20) & 0x0fff)
 
 #define IS_OMAP_SUBCLASS(subclass, id)			\
@@ -92,12 +109,21 @@ static inline int is_ti ##subclass (void)		\
 	return (GET_OMAP_SUBCLASS == (id)) ? 1 : 0;	\
 }
 
+#define IS_AM_SUBCLASS(subclass, id)			\
+static inline int is_am ##subclass (void)		\
+{							\
+	return (GET_OMAP_SUBCLASS == (id)) ? 1 : 0;	\
+}
+
 IS_OMAP_CLASS(7xx, 0x07)
 IS_OMAP_CLASS(15xx, 0x15)
 IS_OMAP_CLASS(16xx, 0x16)
 IS_OMAP_CLASS(24xx, 0x24)
 IS_OMAP_CLASS(34xx, 0x34)
 IS_OMAP_CLASS(44xx, 0x44)
+IS_AM_CLASS(33xx, 0x33)
+
+IS_TI_CLASS(81xx, 0x81)
 
 IS_OMAP_SUBCLASS(242x, 0x242)
 IS_OMAP_SUBCLASS(243x, 0x243)
@@ -105,8 +131,11 @@ IS_OMAP_SUBCLASS(343x, 0x343)
 IS_OMAP_SUBCLASS(363x, 0x363)
 IS_OMAP_SUBCLASS(443x, 0x443)
 IS_OMAP_SUBCLASS(446x, 0x446)
+IS_OMAP_SUBCLASS(447x, 0x447)
 
 IS_TI_SUBCLASS(816x, 0x816)
+IS_TI_SUBCLASS(814x, 0x814)
+IS_AM_SUBCLASS(335x, 0x335)
 
 #define cpu_is_omap7xx()		0
 #define cpu_is_omap15xx()		0
@@ -116,10 +145,15 @@ IS_TI_SUBCLASS(816x, 0x816)
 #define cpu_is_omap243x()		0
 #define cpu_is_omap34xx()		0
 #define cpu_is_omap343x()		0
+#define cpu_is_ti81xx()			0
 #define cpu_is_ti816x()			0
+#define cpu_is_ti814x()			0
+#define cpu_is_am33xx()			0
+#define cpu_is_am335x()			0
 #define cpu_is_omap44xx()		0
 #define cpu_is_omap443x()		0
 #define cpu_is_omap446x()		0
+#define cpu_is_omap447x()		0
 
 #if defined(MULTI_OMAP1)
 # if defined(CONFIG_ARCH_OMAP730)
@@ -322,7 +356,11 @@ IS_OMAP_TYPE(3517, 0x3517)
 # undef cpu_is_omap3530
 # undef cpu_is_omap3505
 # undef cpu_is_omap3517
+# undef cpu_is_ti81xx
 # undef cpu_is_ti816x
+# undef cpu_is_ti814x
+# undef cpu_is_am33xx
+# undef cpu_is_am335x
 # define cpu_is_omap3430()		is_omap3430()
 # define cpu_is_omap3503()		(cpu_is_omap3430() &&		\
 						(!omap3_has_iva()) &&	\
@@ -339,16 +377,22 @@ IS_OMAP_TYPE(3517, 0x3517)
 						!omap3_has_sgx())
 # undef cpu_is_omap3630
 # define cpu_is_omap3630()		is_omap363x()
+# define cpu_is_ti81xx()		is_ti81xx()
 # define cpu_is_ti816x()		is_ti816x()
+# define cpu_is_ti814x()		is_ti814x()
+# define cpu_is_am33xx()		is_am33xx()
+# define cpu_is_am335x()		is_am335x()
 #endif
 
 # if defined(CONFIG_ARCH_OMAP4)
 # undef cpu_is_omap44xx
 # undef cpu_is_omap443x
 # undef cpu_is_omap446x
+# undef cpu_is_omap447x
 # define cpu_is_omap44xx()		is_omap44xx()
 # define cpu_is_omap443x()		is_omap443x()
 # define cpu_is_omap446x()		is_omap446x()
+# define cpu_is_omap447x()		is_omap447x()
 # endif
 
 /* Macros to detect if we have OMAP1 or OMAP2 */
@@ -386,15 +430,27 @@ IS_OMAP_TYPE(3517, 0x3517)
 #define TI8168_REV_ES1_0	TI816X_CLASS
 #define TI8168_REV_ES1_1	(TI816X_CLASS | (0x1 << 8))
 
+#define TI814X_CLASS		0x81400034
+#define TI8148_REV_ES1_0	TI814X_CLASS
+#define TI8148_REV_ES2_0	(TI814X_CLASS | (0x1 << 8))
+#define TI8148_REV_ES2_1	(TI814X_CLASS | (0x2 << 8))
+
+#define AM335X_CLASS		0x33500034
+#define AM335X_REV_ES1_0	AM335X_CLASS
+
 #define OMAP443X_CLASS		0x44300044
 #define OMAP4430_REV_ES1_0	(OMAP443X_CLASS | (0x10 << 8))
 #define OMAP4430_REV_ES2_0	(OMAP443X_CLASS | (0x20 << 8))
 #define OMAP4430_REV_ES2_1	(OMAP443X_CLASS | (0x21 << 8))
 #define OMAP4430_REV_ES2_2	(OMAP443X_CLASS | (0x22 << 8))
+#define OMAP4430_REV_ES2_3	(OMAP443X_CLASS | (0x23 << 8))
 
 #define OMAP446X_CLASS		0x44600044
 #define OMAP4460_REV_ES1_0	(OMAP446X_CLASS | (0x10 << 8))
 
+#define OMAP447X_CLASS		0x44700044
+#define OMAP4470_REV_ES1_0	(OMAP447X_CLASS | (0x10 << 8))
+
 void omap2_check_revision(void);
 
 /*
diff --git a/arch/arm/plat-omap/include/plat/hardware.h b/arch/arm/plat-omap/include/plat/hardware.h
index e87efe1499b8..e897978371c2 100644
--- a/arch/arm/plat-omap/include/plat/hardware.h
+++ b/arch/arm/plat-omap/include/plat/hardware.h
@@ -286,6 +286,7 @@
 #include <plat/omap24xx.h>
 #include <plat/omap34xx.h>
 #include <plat/omap44xx.h>
-#include <plat/ti816x.h>
+#include <plat/ti81xx.h>
+#include <plat/am33xx.h>
 
 #endif	/* __ASM_ARCH_OMAP_HARDWARE_H */
diff --git a/arch/arm/plat-omap/include/plat/io.h b/arch/arm/plat-omap/include/plat/io.h
index 1234944a4da0..0696bae1818b 100644
--- a/arch/arm/plat-omap/include/plat/io.h
+++ b/arch/arm/plat-omap/include/plat/io.h
@@ -73,6 +73,9 @@
 #define OMAP4_L3_IO_OFFSET	0xb4000000
 #define OMAP4_L3_IO_ADDRESS(pa)	IOMEM((pa) + OMAP4_L3_IO_OFFSET) /* L3 */
 
+#define AM33XX_L4_WK_IO_OFFSET	0xb5000000
+#define AM33XX_L4_WK_IO_ADDRESS(pa)	IOMEM((pa) + AM33XX_L4_WK_IO_OFFSET)
+
 #define OMAP4_L3_PER_IO_OFFSET	0xb1100000
 #define OMAP4_L3_PER_IO_ADDRESS(pa)	IOMEM((pa) + OMAP4_L3_PER_IO_OFFSET)
 
@@ -154,6 +157,15 @@
 #define L4_34XX_SIZE		SZ_4M   /* 1MB of 128MB used, want 1MB sect */
 
 /*
+ * ----------------------------------------------------------------------------
+ * AM33XX specific IO mapping
+ * ----------------------------------------------------------------------------
+ */
+#define L4_WK_AM33XX_PHYS	L4_WK_AM33XX_BASE
+#define L4_WK_AM33XX_VIRT	(L4_WK_AM33XX_PHYS + AM33XX_L4_WK_IO_OFFSET)
+#define L4_WK_AM33XX_SIZE	SZ_4M   /* 1MB of 128MB used, want 1MB sect */
+
+/*
  * Need to look at the Size 4M for L4.
  * VPOM3430 was not working for Int controller
  */
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
index 2682043f5a5b..9ff444469f3d 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -19,6 +19,7 @@
 
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
+#include <linux/pm_qos.h>
 
 #include <plat/mux.h>
 
@@ -33,6 +34,8 @@
 
 #define OMAP_MODE13X_SPEED	230400
 
+#define OMAP_UART_SCR_TX_EMPTY	0x08
+
 /* WER = 0x7F
  * Enable module level wakeup in WER reg
  */
@@ -51,18 +54,27 @@
 
 #define OMAP_UART_DMA_CH_FREE	-1
 
-#define RX_TIMEOUT		(3 * HZ)
 #define OMAP_MAX_HSUART_PORTS	4
 
 #define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
 
+#define UART_ERRATA_i202_MDR1_ACCESS	BIT(0)
+#define UART_ERRATA_i291_DMA_FORCEIDLE	BIT(1)
+
 struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
-	void __iomem		*membase;	/* ioremap cookie or NULL */
-	resource_size_t		mapbase;	/* resource base */
-	unsigned long		irqflags;	/* request_irq flags */
 	upf_t			flags;		/* UPF_* flags */
+	u32			errata;
+	unsigned int		dma_rx_buf_size;
+	unsigned int		dma_rx_timeout;
+	unsigned int		autosuspend_timeout;
+	unsigned int		dma_rx_poll_rate;
+
+	int (*get_context_loss_count)(struct device *);
+	void (*set_forceidle)(struct platform_device *);
+	void (*set_noidle)(struct platform_device *);
+	void (*enable_wakeup)(struct platform_device *, bool);
 };
 
 struct uart_omap_dma {
@@ -86,8 +98,9 @@ struct uart_omap_dma {
 	spinlock_t		rx_lock;
 	/* timer to poll activity on rx dma */
 	struct timer_list	rx_timer;
-	int			rx_buf_size;
-	int			rx_timeout;
+	unsigned int		rx_buf_size;
+	unsigned int		rx_poll_rate;
+	unsigned int		rx_timeout;
 };
 
 struct uart_omap_port {
@@ -100,6 +113,10 @@ struct uart_omap_port {
 	unsigned char		mcr;
 	unsigned char		fcr;
 	unsigned char		efr;
+	unsigned char		dll;
+	unsigned char		dlh;
+	unsigned char		mdr1;
+	unsigned char		scr;
 
 	int			use_dma;
 	/*
@@ -111,6 +128,14 @@ struct uart_omap_port {
 	unsigned char		msr_saved_flags;
 	char			name[20];
 	unsigned long		port_activity;
+	u32			context_loss_cnt;
+	u32			errata;
+	u8			wakeups_enabled;
+
+	struct pm_qos_request	pm_qos_request;
+	u32			latency;
+	u32			calc_latency;
+	struct work_struct	qos_work;
 };
 
 #endif /* __OMAP_SERIAL_H__ */
diff --git a/arch/arm/plat-omap/include/plat/omap34xx.h b/arch/arm/plat-omap/include/plat/omap34xx.h
index b9e85886b9d6..0d818acf3917 100644
--- a/arch/arm/plat-omap/include/plat/omap34xx.h
+++ b/arch/arm/plat-omap/include/plat/omap34xx.h
@@ -35,6 +35,8 @@
 #define L4_EMU_34XX_BASE	0x54000000
 #define L3_34XX_BASE		0x68000000
 
+#define L4_WK_AM33XX_BASE	0x44C00000
+
 #define OMAP3430_32KSYNCT_BASE	0x48320000
 #define OMAP3430_CM_BASE	0x48004800
 #define OMAP3430_PRM_BASE	0x48306800
diff --git a/arch/arm/plat-omap/include/plat/serial.h b/arch/arm/plat-omap/include/plat/serial.h
index 1ab9fd6abe6d..38b3e38df2a0 100644
--- a/arch/arm/plat-omap/include/plat/serial.h
+++ b/arch/arm/plat-omap/include/plat/serial.h
@@ -51,10 +51,10 @@
 #define OMAP4_UART3_BASE	0x48020000
 #define OMAP4_UART4_BASE	0x4806e000
 
-/* TI816X serial ports */
-#define TI816X_UART1_BASE	0x48020000
-#define TI816X_UART2_BASE	0x48022000
-#define TI816X_UART3_BASE	0x48024000
+/* TI81XX serial ports */
+#define TI81XX_UART1_BASE	0x48020000
+#define TI81XX_UART2_BASE	0x48022000
+#define TI81XX_UART3_BASE	0x48024000
 
 /* AM3505/3517 UART4 */
 #define AM35XX_UART4_BASE	0x4809E000	/* Only on AM3505/3517 */
@@ -89,9 +89,9 @@
 #define OMAP4UART2		OMAP2UART2
 #define OMAP4UART3		43
 #define OMAP4UART4		44
-#define TI816XUART1		81
-#define TI816XUART2		82
-#define TI816XUART3		83
+#define TI81XXUART1		81
+#define TI81XXUART2		82
+#define TI81XXUART3		83
 #define ZOOM_UART		95		/* Only on zoom2/3 */
 
 /* This is only used by 8250.c for omap1510 */
@@ -106,15 +106,13 @@
 #ifndef __ASSEMBLER__
 
 struct omap_board_data;
+struct omap_uart_port_info;
 
 extern void omap_serial_init(void);
-extern void omap_serial_init_port(struct omap_board_data *bdata);
 extern int omap_uart_can_sleep(void);
-extern void omap_uart_check_wakeup(void);
-extern void omap_uart_prepare_suspend(void);
-extern void omap_uart_prepare_idle(int num);
-extern void omap_uart_resume_idle(int num);
-extern void omap_uart_enable_irqs(int enable);
+extern void omap_serial_board_init(struct omap_uart_port_info *platform_data);
+extern void omap_serial_init_port(struct omap_board_data *bdata,
+		struct omap_uart_port_info *platform_data);
 #endif
 
 #endif
diff --git a/arch/arm/plat-omap/include/plat/ti816x.h b/arch/arm/plat-omap/include/plat/ti81xx.h
index 50510f5dda1e..8f9843f78422 100644
--- a/arch/arm/plat-omap/include/plat/ti816x.h
+++ b/arch/arm/plat-omap/include/plat/ti81xx.h
@@ -1,5 +1,5 @@
 /*
- * This file contains the address data for various TI816X modules.
+ * This file contains the address data for various TI81XX modules.
  *
  * Copyright (C) 2010 Texas Instruments, Inc. - http://www.ti.com/
  *
@@ -13,15 +13,15 @@
  * GNU General Public License for more details.
  */
 
-#ifndef __ASM_ARCH_TI816X_H
-#define __ASM_ARCH_TI816X_H
+#ifndef __ASM_ARCH_TI81XX_H
+#define __ASM_ARCH_TI81XX_H
 
-#define L4_SLOW_TI816X_BASE	0x48000000
+#define L4_SLOW_TI81XX_BASE	0x48000000
 
-#define TI816X_SCM_BASE		0x48140000
-#define TI816X_CTRL_BASE	TI816X_SCM_BASE
-#define TI816X_PRCM_BASE	0x48180000
+#define TI81XX_SCM_BASE		0x48140000
+#define TI81XX_CTRL_BASE	TI81XX_SCM_BASE
+#define TI81XX_PRCM_BASE	0x48180000
 
-#define TI816X_ARM_INTC_BASE	0x48200000
+#define TI81XX_ARM_INTC_BASE	0x48200000
 
-#endif /* __ASM_ARCH_TI816X_H */
+#endif /* __ASM_ARCH_TI81XX_H */
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index 2f472e989ec6..7fbc361946b5 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -99,9 +99,9 @@ static inline void flush(void)
 #define DEBUG_LL_ZOOM(mach)						\
 	_DEBUG_LL_ENTRY(mach, ZOOM_UART_BASE, ZOOM_PORT_SHIFT, ZOOM_UART)
 
-#define DEBUG_LL_TI816X(p, mach)					\
-	_DEBUG_LL_ENTRY(mach, TI816X_UART##p##_BASE, OMAP_PORT_SHIFT,	\
-		TI816XUART##p)
+#define DEBUG_LL_TI81XX(p, mach)					\
+	_DEBUG_LL_ENTRY(mach, TI81XX_UART##p##_BASE, OMAP_PORT_SHIFT,	\
+		TI81XXUART##p)
 
 static inline void __arch_decomp_setup(unsigned long arch_id)
 {
@@ -177,7 +177,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		DEBUG_LL_ZOOM(omap_zoom3);
 
 		/* TI8168 base boards using UART3 */
-		DEBUG_LL_TI816X(3, ti8168evm);
+		DEBUG_LL_TI81XX(3, ti8168evm);
 
 	} while (0);
 }