at91: drop at572d940hf support

no-one use it and it's nearly impossible get a board to work on it
and the Mainline implementation was never finished

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>

14 files changed, 2 insertions, 2350 deletions

diff --git a/arch/arm/configs/at572d940hfek_defconfig b/arch/arm/configs/at572d940hfek_defconfig
deleted file mode 100644
index 1b1158ae8f82..000000000000
--- a/arch/arm/configs/at572d940hfek_defconfig
+++ /dev/null
@@ -1,358 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_LOCALVERSION="-AT572D940HF"
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_BSD_PROCESS_ACCT_V3=y
-CONFIG_TASKSTATS=y
-CONFIG_TASK_XACCT=y
-CONFIG_TASK_IO_ACCOUNTING=y
-CONFIG_AUDIT=y
-CONFIG_CGROUPS=y
-CONFIG_CGROUP_CPUACCT=y
-CONFIG_CGROUP_SCHED=y
-CONFIG_RT_GROUP_SCHED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_RELAY=y
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_PROFILING=y
-CONFIG_OPROFILE=m
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT572D940HF=y
-CONFIG_MACH_AT572D940HFEB=y
-CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
-CONFIG_CMDLINE="mem=48M console=ttyS0 initrd=0x21100000,3145728 root=/dev/ram0 rw ip=172.16.1.181"
-CONFIG_KEXEC=y
-CONFIG_FPE_NWFPE=y
-CONFIG_FPE_NWFPE_XP=y
-CONFIG_NET=y
-CONFIG_PACKET=m
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_NET_PKTGEN=m
-CONFIG_NET_TCPPROBE=m
-CONFIG_CAN=m
-CONFIG_CAN_RAW=m
-CONFIG_CAN_BCM=m
-CONFIG_CAN_VCAN=m
-CONFIG_CAN_DEBUG_DEVICES=y
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_CONNECTOR=m
-CONFIG_MTD=m
-CONFIG_MTD_DEBUG=y
-CONFIG_MTD_DEBUG_VERBOSE=1
-CONFIG_MTD_CONCAT=m
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CHAR=m
-CONFIG_MTD_BLOCK=m
-CONFIG_MTD_BLOCK_RO=m
-CONFIG_FTL=m
-CONFIG_NFTL=m
-CONFIG_NFTL_RW=y
-CONFIG_INFTL=m
-CONFIG_RFD_FTL=m
-CONFIG_SSFDC=m
-CONFIG_MTD_OOPS=m
-CONFIG_MTD_CFI=m
-CONFIG_MTD_JEDECPROBE=m
-CONFIG_MTD_CFI_INTELEXT=m
-CONFIG_MTD_CFI_AMDSTD=m
-CONFIG_MTD_CFI_STAA=m
-CONFIG_MTD_ROM=m
-CONFIG_MTD_ABSENT=m
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_PHYSMAP=m
-CONFIG_MTD_PLATRAM=m
-CONFIG_MTD_DATAFLASH=m
-CONFIG_MTD_M25P80=m
-CONFIG_MTD_SLRAM=m
-CONFIG_MTD_PHRAM=m
-CONFIG_MTD_MTDRAM=m
-CONFIG_MTD_BLOCK2MTD=m
-CONFIG_MTD_NAND=m
-CONFIG_MTD_NAND_VERIFY_WRITE=y
-CONFIG_MTD_NAND_DISKONCHIP=m
-CONFIG_MTD_NAND_NANDSIM=m
-CONFIG_MTD_NAND_PLATFORM=m
-CONFIG_MTD_ALAUDA=m
-CONFIG_MTD_UBI=m
-CONFIG_MTD_UBI_GLUEBI=m
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_CRYPTOLOOP=m
-CONFIG_BLK_DEV_NBD=m
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=65536
-CONFIG_ATMEL_TCLIB=y
-CONFIG_ATMEL_SSC=m
-CONFIG_SENSORS_TSL2550=m
-CONFIG_DS1682=m
-CONFIG_RAID_ATTRS=m
-CONFIG_SCSI=m
-CONFIG_SCSI_TGT=m
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_BLK_DEV_SD=m
-CONFIG_BLK_DEV_SR=m
-CONFIG_CHR_DEV_SG=m
-CONFIG_CHR_DEV_SCH=m
-CONFIG_SCSI_MULTI_LUN=y
-CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_LOGGING=y
-CONFIG_SCSI_SCAN_ASYNC=y
-CONFIG_SCSI_ISCSI_ATTRS=m
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=m
-CONFIG_BONDING=m
-CONFIG_MACVLAN=m
-CONFIG_EQUALIZER=m
-CONFIG_TUN=m
-CONFIG_VETH=m
-CONFIG_PHYLIB=y
-CONFIG_MARVELL_PHY=m
-CONFIG_DAVICOM_PHY=m
-CONFIG_QSEMI_PHY=m
-CONFIG_LXT_PHY=m
-CONFIG_CICADA_PHY=m
-CONFIG_VITESSE_PHY=m
-CONFIG_SMSC_PHY=m
-CONFIG_BROADCOM_PHY=m
-CONFIG_ICPLUS_PHY=m
-CONFIG_MDIO_BITBANG=m
-CONFIG_NET_ETHERNET=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-CONFIG_USB_ZD1201=m
-CONFIG_HOSTAP=m
-CONFIG_HOSTAP_FIRMWARE=y
-CONFIG_HOSTAP_FIRMWARE_NVRAM=y
-CONFIG_USB_CATC=m
-CONFIG_USB_KAWETH=m
-CONFIG_USB_PEGASUS=m
-CONFIG_USB_RTL8150=m
-CONFIG_USB_USBNET=m
-CONFIG_USB_NET_DM9601=m
-CONFIG_USB_NET_GL620A=m
-CONFIG_USB_NET_PLUSB=m
-CONFIG_USB_NET_MCS7830=m
-CONFIG_USB_NET_RNDIS_HOST=m
-CONFIG_USB_ALI_M5632=y
-CONFIG_USB_AN2720=y
-CONFIG_USB_EPSON2888=y
-CONFIG_USB_KC2190=y
-# CONFIG_USB_NET_ZAURUS is not set
-CONFIG_INPUT_MOUSEDEV=m
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-CONFIG_KEYBOARD_LKKBD=m
-CONFIG_KEYBOARD_GPIO=m
-CONFIG_KEYBOARD_NEWTON=m
-CONFIG_KEYBOARD_STOWAWAY=m
-CONFIG_KEYBOARD_SUNKBD=m
-CONFIG_KEYBOARD_XTKBD=m
-CONFIG_MOUSE_PS2=m
-CONFIG_MOUSE_SERIAL=m
-CONFIG_MOUSE_APPLETOUCH=m
-CONFIG_MOUSE_VSXXXAA=m
-CONFIG_MOUSE_GPIO=m
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_UINPUT=m
-CONFIG_SERIO_SERPORT=m
-CONFIG_SERIO_RAW=m
-CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_SERIAL_NONSTANDARD=y
-CONFIG_N_HDLC=m
-CONFIG_SPECIALIX=m
-CONFIG_STALDRV=y
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_IPMI_HANDLER=m
-CONFIG_IPMI_DEVICE_INTERFACE=m
-CONFIG_IPMI_SI=m
-CONFIG_IPMI_WATCHDOG=m
-CONFIG_IPMI_POWEROFF=m
-CONFIG_HW_RANDOM=y
-CONFIG_R3964=m
-CONFIG_RAW_DRIVER=m
-CONFIG_TCG_TPM=m
-CONFIG_TCG_NSC=m
-CONFIG_TCG_ATMEL=m
-CONFIG_I2C=m
-CONFIG_I2C_CHARDEV=m
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=y
-CONFIG_SPI_BITBANG=m
-CONFIG_SPI_SPIDEV=m
-# CONFIG_HWMON is not set
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=m
-CONFIG_SND=m
-CONFIG_SND_SEQUENCER=m
-CONFIG_SND_SEQ_DUMMY=m
-CONFIG_SND_MIXER_OSS=m
-CONFIG_SND_PCM_OSS=m
-# CONFIG_SND_PCM_OSS_PLUGINS is not set
-CONFIG_SND_SEQUENCER_OSS=y
-CONFIG_SND_DYNAMIC_MINORS=y
-# CONFIG_SND_VERBOSE_PROCFS is not set
-CONFIG_SND_DUMMY=m
-CONFIG_SND_VIRMIDI=m
-CONFIG_SND_USB_AUDIO=m
-CONFIG_SND_USB_CAIAQ=m
-CONFIG_SND_USB_CAIAQ_INPUT=y
-CONFIG_HID=m
-CONFIG_HIDRAW=y
-CONFIG_USB_HID=m
-CONFIG_USB_HIDDEV=y
-CONFIG_USB_KBD=m
-CONFIG_USB_MOUSE=m
-CONFIG_HID_A4TECH=m
-CONFIG_HID_APPLE=m
-CONFIG_HID_BELKIN=m
-CONFIG_HID_CHERRY=m
-CONFIG_HID_CHICONY=m
-CONFIG_HID_CYPRESS=m
-CONFIG_HID_EZKEY=m
-CONFIG_HID_GYRATION=m
-CONFIG_HID_LOGITECH=m
-CONFIG_HID_MICROSOFT=m
-CONFIG_HID_MONTEREY=m
-CONFIG_HID_PANTHERLORD=m
-CONFIG_HID_PETALYNX=m
-CONFIG_HID_SAMSUNG=m
-CONFIG_HID_SONY=m
-CONFIG_HID_SUNPLUS=m
-CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=m
-CONFIG_USB_STORAGE_DATAFAB=m
-CONFIG_USB_STORAGE_FREECOM=m
-CONFIG_USB_STORAGE_ISD200=m
-CONFIG_USB_STORAGE_USBAT=m
-CONFIG_USB_STORAGE_SDDR09=m
-CONFIG_USB_STORAGE_SDDR55=m
-CONFIG_USB_STORAGE_JUMPSHOT=m
-CONFIG_USB_STORAGE_ALAUDA=m
-CONFIG_USB_STORAGE_KARMA=m
-CONFIG_USB_LIBUSUAL=y
-CONFIG_USB_SERIAL=m
-CONFIG_USB_EZUSB=y
-CONFIG_USB_SERIAL_GENERIC=y
-CONFIG_USB_SERIAL_PL2303=m
-CONFIG_USB_SERIAL_SPCP8X5=m
-CONFIG_USB_SERIAL_DEBUG=m
-CONFIG_USB_EMI62=m
-CONFIG_USB_EMI26=m
-CONFIG_USB_ADUTUX=m
-CONFIG_USB_TEST=m
-CONFIG_USB_GADGET=m
-CONFIG_USB_GADGET_DEBUG_FILES=y
-CONFIG_USB_GADGET_DEBUG_FS=y
-CONFIG_USB_ZERO=m
-CONFIG_USB_ETH=m
-CONFIG_USB_GADGETFS=m
-CONFIG_USB_FILE_STORAGE=m
-CONFIG_USB_G_SERIAL=m
-CONFIG_USB_MIDI_GADGET=m
-CONFIG_MMC=y
-CONFIG_SDIO_UART=m
-CONFIG_MMC_AT91=m
-CONFIG_MMC_SPI=m
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=m
-CONFIG_LEDS_GPIO=m
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=m
-CONFIG_LEDS_TRIGGER_HEARTBEAT=m
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_INTF_DEV_UIE_EMUL=y
-CONFIG_RTC_DRV_DS1307=m
-CONFIG_RTC_DRV_DS1305=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT2_FS_SECURITY=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_EXT3_FS_SECURITY=y
-CONFIG_JBD_DEBUG=y
-CONFIG_REISERFS_FS=m
-CONFIG_REISERFS_CHECK=y
-CONFIG_REISERFS_PROC_INFO=y
-CONFIG_REISERFS_FS_XATTR=y
-CONFIG_REISERFS_FS_POSIX_ACL=y
-CONFIG_REISERFS_FS_SECURITY=y
-CONFIG_INOTIFY=y
-CONFIG_FUSE_FS=m
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=y
-CONFIG_NTFS_FS=m
-CONFIG_NTFS_RW=y
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_JFFS2_FS=m
-CONFIG_JFFS2_COMPRESSION_OPTIONS=y
-CONFIG_JFFS2_LZO=y
-CONFIG_JFFS2_CMODE_FAVOURLZO=y
-CONFIG_CRAMFS=m
-CONFIG_NFS_FS=m
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFSD=m
-CONFIG_NFSD_V3_ACL=y
-CONFIG_NFSD_V4=y
-CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAC_PARTITION=y
-CONFIG_BSD_DISKLABEL=y
-CONFIG_MINIX_SUBPARTITION=y
-CONFIG_SOLARIS_X86_PARTITION=y
-CONFIG_UNIXWARE_DISKLABEL=y
-CONFIG_LDM_PARTITION=y
-CONFIG_LDM_DEBUG=y
-CONFIG_SGI_PARTITION=y
-CONFIG_SUN_PARTITION=y
-CONFIG_NLS_DEFAULT="cp437"
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=m
-CONFIG_NLS_ASCII=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_UTF8=m
-CONFIG_DLM=m
-CONFIG_PRINTK_TIME=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_UNUSED_SYMBOLS=y
-CONFIG_DEBUG_FS=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_GF128MUL=m
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC_CCITT=m
-CONFIG_CRC16=m
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 8cbc3aae6c64..22484670e7ba 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -82,11 +82,6 @@ config ARCH_AT91CAP9
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
 
-config ARCH_AT572D940HF
-	bool "AT572D940HF"
-	select CPU_ARM926T
-	select GENERIC_CLOCKEVENTS
-
 config ARCH_AT91X40
 	bool "AT91x40"
 	select ARCH_USES_GETTIMEOFFSET
@@ -431,22 +426,6 @@ endif
 
 # ----------------------------------------------------------
 
-if ARCH_AT572D940HF
-
-comment "AT572D940HF Board Type"
-
-config MACH_AT572D940HFEB
-	bool "AT572D940HF-EK"
-	depends on ARCH_AT572D940HF
-	select HAVE_AT91_DATAFLASH_CARD
-	help
-	  Select this if you are using Atmel's AT572D940HF-EK evaluation kit.
-	  <http://www.atmel.com/products/diopsis/default.asp>
-
-endif
-
-# ----------------------------------------------------------
-
 if ARCH_AT91X40
 
 comment "AT91X40 Board Type"
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index a83835e0c185..96966231920c 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -19,7 +19,6 @@ obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devi
 obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o at91sam9_alt_reset.o
 obj-$(CONFIG_ARCH_AT91SAM9G45)	+= at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91CAP9)	+= at91cap9.o at91sam926x_time.o at91cap9_devices.o sam9_smc.o
-obj-$(CONFIG_ARCH_AT572D940HF)  += at572d940hf.o at91sam926x_time.o at572d940hf_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o
 
 # AT91RM9200 board-specific support
@@ -78,9 +77,6 @@ obj-$(CONFIG_MACH_AT91SAM9M10G45EK) += board-sam9m10g45ek.o
 # AT91CAP9 board-specific support
 obj-$(CONFIG_MACH_AT91CAP9ADK)	+= board-cap9adk.o
 
-# AT572D940HF board-specific support
-obj-$(CONFIG_MACH_AT572D940HFEB) += board-at572d940hf_ek.o
-
 # AT91X40 board-specific support
 obj-$(CONFIG_MACH_AT91EB01)	+= board-eb01.o
 
diff --git a/arch/arm/mach-at91/at572d940hf.c b/arch/arm/mach-at91/at572d940hf.c
deleted file mode 100644
index d06990777ffe..000000000000
--- a/arch/arm/mach-at91/at572d940hf.c
+++ /dev/null
@@ -1,412 +0,0 @@
-/*
- * arch/arm/mach-at91/at572d940hf.c
- *
- * Antonio R. Costa <costa.antonior@gmail.com>
- * Copyright (C) 2008 Atmel
- *
- * Copyright (C) 2005 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#include <linux/module.h>
-
-#include <asm/mach/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <mach/at572d940hf.h>
-#include <mach/at91_pmc.h>
-#include <mach/at91_rstc.h>
-
-#include "generic.h"
-#include "clock.h"
-
-static struct map_desc at572d940hf_io_desc[] __initdata = {
-	{
-		.virtual	= AT91_VA_BASE_SYS,
-		.pfn		= __phys_to_pfn(AT91_BASE_SYS),
-		.length		= SZ_16K,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= AT91_IO_VIRT_BASE - AT572D940HF_SRAM_SIZE,
-		.pfn		= __phys_to_pfn(AT572D940HF_SRAM_BASE),
-		.length		= AT572D940HF_SRAM_SIZE,
-		.type		= MT_DEVICE,
-	},
-};
-
-/* --------------------------------------------------------------------
- *  Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioA_clk = {
-	.name		= "pioA_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_PIOA,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
-	.name		= "pioB_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_PIOB,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioC_clk = {
-	.name		= "pioC_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_PIOC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk macb_clk = {
-	.name		= "macb_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_EMAC,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
-	.name		= "usart0_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_US0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
-	.name		= "usart1_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_US1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
-	.name		= "usart2_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_US2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc_clk = {
-	.name		= "mci_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_MCI,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk udc_clk = {
-	.name		= "udc_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_UDP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi0_clk = {
-	.name		= "twi0_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_TWI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
-	.name		= "spi0_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_SPI0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
-	.name		= "spi1_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_SPI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
-	.name		= "ssc0_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_SSC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
-	.name		= "ssc1_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_SSC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc2_clk = {
-	.name		= "ssc2_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_SSC2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc0_clk = {
-	.name		= "tc0_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_TC0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc1_clk = {
-	.name		= "tc1_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_TC1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk tc2_clk = {
-	.name		= "tc2_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_TC2,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
-	.name		= "ohci_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_UHP,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc3_clk = {
-	.name		= "ssc3_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_SSC3,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi1_clk = {
-	.name		= "twi1_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_TWI1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk can0_clk = {
-	.name		= "can0_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_CAN0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk can1_clk = {
-	.name		= "can1_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_CAN1,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-static struct clk mAgicV_clk = {
-	.name		= "mAgicV_clk",
-	.pmc_mask	= 1 << AT572D940HF_ID_MSIRQ0,
-	.type		= CLK_TYPE_PERIPHERAL,
-};
-
-
-static struct clk *periph_clocks[] __initdata = {
-	&pioA_clk,
-	&pioB_clk,
-	&pioC_clk,
-	&macb_clk,
-	&usart0_clk,
-	&usart1_clk,
-	&usart2_clk,
-	&mmc_clk,
-	&udc_clk,
-	&twi0_clk,
-	&spi0_clk,
-	&spi1_clk,
-	&ssc0_clk,
-	&ssc1_clk,
-	&ssc2_clk,
-	&tc0_clk,
-	&tc1_clk,
-	&tc2_clk,
-	&ohci_clk,
-	&ssc3_clk,
-	&twi1_clk,
-	&can0_clk,
-	&can1_clk,
-	&mAgicV_clk,
-	/* irq0 .. irq2 */
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
-	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
-	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
-	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
-	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
-	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-};
-
-/*
- * The five programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
-	.name		= "pck0",
-	.pmc_mask	= AT91_PMC_PCK0,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 0,
-};
-static struct clk pck1 = {
-	.name		= "pck1",
-	.pmc_mask	= AT91_PMC_PCK1,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 1,
-};
-static struct clk pck2 = {
-	.name		= "pck2",
-	.pmc_mask	= AT91_PMC_PCK2,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 2,
-};
-static struct clk pck3 = {
-	.name		= "pck3",
-	.pmc_mask	= AT91_PMC_PCK3,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 3,
-};
-
-static struct clk mAgicV_mem_clk = {
-	.name		= "mAgicV_mem_clk",
-	.pmc_mask	= AT91_PMC_PCK4,
-	.type		= CLK_TYPE_PROGRAMMABLE,
-	.id		= 4,
-};
-
-/* HClocks */
-static struct clk hck0 = {
-	.name		= "hck0",
-	.pmc_mask	= AT91_PMC_HCK0,
-	.type		= CLK_TYPE_SYSTEM,
-	.id		= 0,
-};
-static struct clk hck1 = {
-	.name		= "hck1",
-	.pmc_mask	= AT91_PMC_HCK1,
-	.type		= CLK_TYPE_SYSTEM,
-	.id		= 1,
-};
-
-static void __init at572d940hf_register_clocks(void)
-{
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
-		clk_register(periph_clocks[i]);
-
-	clkdev_add_table(periph_clocks_lookups,
-			 ARRAY_SIZE(periph_clocks_lookups));
-	clkdev_add_table(usart_clocks_lookups,
-			 ARRAY_SIZE(usart_clocks_lookups));
-
-	clk_register(&pck0);
-	clk_register(&pck1);
-	clk_register(&pck2);
-	clk_register(&pck3);
-	clk_register(&mAgicV_mem_clk);
-
-	clk_register(&hck0);
-	clk_register(&hck1);
-}
-
-static struct clk_lookup console_clock_lookup;
-
-void __init at572d940hf_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
-/* --------------------------------------------------------------------
- *  GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at572d940hf_gpio[] = {
-	{
-		.id		= AT572D940HF_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
-	}, {
-		.id		= AT572D940HF_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
-	}, {
-		.id		= AT572D940HF_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
-	}
-};
-
-static void at572d940hf_reset(void)
-{
-	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
-}
-
-
-/* --------------------------------------------------------------------
- *  AT572D940HF processor initialization
- * -------------------------------------------------------------------- */
-
-void __init at572d940hf_map_io(void)
-{
-	/* Map peripherals */
-	iotable_init(at572d940hf_io_desc, ARRAY_SIZE(at572d940hf_io_desc));
-}
-
-void __init at572d940hf_initialize(unsigned long main_clock)
-{
-	at91_arch_reset = at572d940hf_reset;
-	at91_extern_irq = (1 << AT572D940HF_ID_IRQ0) | (1 << AT572D940HF_ID_IRQ1)
-			| (1 << AT572D940HF_ID_IRQ2);
-
-	/* Init clock subsystem */
-	at91_clock_init(main_clock);
-
-	/* Register the processor-specific clocks */
-	at572d940hf_register_clocks();
-
-	/* Register GPIO subsystem */
-	at91_gpio_init(at572d940hf_gpio, 3);
-}
-
-/* --------------------------------------------------------------------
- *  Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at572d940hf_default_irq_priority[NR_AIC_IRQS] __initdata = {
-	7,	/* Advanced Interrupt Controller */
-	7,	/* System Peripherals */
-	0,	/* Parallel IO Controller A */
-	0,	/* Parallel IO Controller B */
-	0,	/* Parallel IO Controller C */
-	3,	/* Ethernet */
-	6,	/* USART 0 */
-	6,	/* USART 1 */
-	6,	/* USART 2 */
-	0,	/* Multimedia Card Interface */
-	4,	/* USB Device Port */
-	0,	/* Two-Wire Interface 0 */
-	6,	/* Serial Peripheral Interface 0 */
-	6,	/* Serial Peripheral Interface 1 */
-	5,	/* Serial Synchronous Controller 0 */
-	5,	/* Serial Synchronous Controller 1 */
-	5,	/* Serial Synchronous Controller 2 */
-	0,	/* Timer Counter 0 */
-	0,	/* Timer Counter 1 */
-	0,	/* Timer Counter 2 */
-	3,	/* USB Host port */
-	3,	/* Serial Synchronous Controller 3 */
-	0,	/* Two-Wire Interface 1 */
-	0,	/* CAN Controller 0 */
-	0,	/* CAN Controller 1 */
-	0,	/* mAgicV HALT line */
-	0,	/* mAgicV SIRQ0 line */
-	0,	/* mAgicV exception line */
-	0,	/* mAgicV end of DMA line */
-	0,	/* Advanced Interrupt Controller */
-	0,	/* Advanced Interrupt Controller */
-	0,	/* Advanced Interrupt Controller */
-};
-
-void __init at572d940hf_init_interrupts(unsigned int priority[NR_AIC_IRQS])
-{
-	if (!priority)
-		priority = at572d940hf_default_irq_priority;
-
-	/* Initialize the AIC interrupt controller */
-	at91_aic_init(priority);
-
-	/* Enable GPIO interrupts */
-	at91_gpio_irq_setup();
-}
-
diff --git a/arch/arm/mach-at91/at572d940hf_devices.c b/arch/arm/mach-at91/at572d940hf_devices.c
deleted file mode 100644
index 14863b8e7e6a..000000000000
--- a/arch/arm/mach-at91/at572d940hf_devices.c
+++ /dev/null
@@ -1,964 +0,0 @@
-/*
- * arch/arm/mach-at91/at572d940hf_devices.c
- *
- * Copyright (C) 2008 Atmel Antonio R. Costa <costa.antonior@gmail.com>
- * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- * Copyright (C) 2005 David Brownell
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-
-#include <mach/board.h>
-#include <mach/gpio.h>
-#include <mach/at572d940hf.h>
-#include <mach/at572d940hf_matrix.h>
-#include <mach/at91sam9_smc.h>
-
-#include "generic.h"
-#include "sam9_smc.h"
-
-
-/* --------------------------------------------------------------------
- *  USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_UHP_BASE,
-		.end	= AT572D940HF_UHP_BASE + SZ_1M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_UHP,
-		.end	= AT572D940HF_ID_UHP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_usbh_device = {
-	.name		= "at91_ohci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &ohci_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &usbh_data,
-	},
-	.resource	= usbh_resources,
-	.num_resources	= ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
-	if (!data)
-		return;
-
-	usbh_data = *data;
-	platform_device_register(&at572d940hf_usbh_device);
-
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_USB_GADGET_AT91
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_UDP,
-		.end	= AT572D940HF_BASE_UDP + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_UDP,
-		.end	= AT572D940HF_ID_UDP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_udc_device = {
-	.name		= "at91_udc",
-	.id		= -1,
-	.dev		= {
-				.platform_data		= &udc_data,
-	},
-	.resource	= udc_resources,
-	.num_resources	= ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
-	if (!data)
-		return;
-
-	if (data->vbus_pin) {
-		at91_set_gpio_input(data->vbus_pin, 0);
-		at91_set_deglitch(data->vbus_pin, 1);
-	}
-
-	/* Pullup pin is handled internally */
-
-	udc_data = *data;
-	platform_device_register(&at572d940hf_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
-
-static struct resource eth_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_EMAC,
-		.end	= AT572D940HF_BASE_EMAC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_EMAC,
-		.end	= AT572D940HF_ID_EMAC,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_eth_device = {
-	.name		= "macb",
-	.id		= -1,
-	.dev		= {
-			.dma_mask		= &eth_dmamask,
-			.coherent_dma_mask	= DMA_BIT_MASK(32),
-			.platform_data		= &eth_data,
-	},
-	.resource	= eth_resources,
-	.num_resources	= ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct at91_eth_data *data)
-{
-	if (!data)
-		return;
-
-	if (data->phy_irq_pin) {
-		at91_set_gpio_input(data->phy_irq_pin, 0);
-		at91_set_deglitch(data->phy_irq_pin, 1);
-	}
-
-	/* Only RMII is supported */
-	data->is_rmii = 1;
-
-	/* Pins used for RMII */
-	at91_set_A_periph(AT91_PIN_PA16, 0);	/* ETXCK_EREFCK */
-	at91_set_A_periph(AT91_PIN_PA17, 0);	/* ERXDV */
-	at91_set_A_periph(AT91_PIN_PA18, 0);	/* ERX0 */
-	at91_set_A_periph(AT91_PIN_PA19, 0);	/* ERX1 */
-	at91_set_A_periph(AT91_PIN_PA20, 0);	/* ERXER */
-	at91_set_A_periph(AT91_PIN_PA23, 0);	/* ETXEN */
-	at91_set_A_periph(AT91_PIN_PA21, 0);	/* ETX0 */
-	at91_set_A_periph(AT91_PIN_PA22, 0);	/* ETX1 */
-	at91_set_A_periph(AT91_PIN_PA13, 0);	/* EMDIO */
-	at91_set_A_periph(AT91_PIN_PA14, 0);	/* EMDC */
-
-	eth_data = *data;
-	platform_device_register(&at572d940hf_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  MMC / SD
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc_data;
-
-static struct resource mmc_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_MCI,
-		.end	= AT572D940HF_BASE_MCI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_MCI,
-		.end	= AT572D940HF_ID_MCI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_mmc_device = {
-	.name		= "at91_mci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &mmc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &mmc_data,
-	},
-	.resource	= mmc_resources,
-	.num_resources	= ARRAY_SIZE(mmc_resources),
-};
-
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
-{
-	if (!data)
-		return;
-
-	/* input/irq */
-	if (data->det_pin) {
-		at91_set_gpio_input(data->det_pin, 1);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-	if (data->wp_pin)
-		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
-		at91_set_gpio_output(data->vcc_pin, 0);
-
-	/* CLK */
-	at91_set_A_periph(AT91_PIN_PC22, 0);
-
-	/* CMD */
-	at91_set_A_periph(AT91_PIN_PC23, 1);
-
-	/* DAT0, maybe DAT1..DAT3 */
-	at91_set_A_periph(AT91_PIN_PC24, 1);
-	if (data->wire4) {
-		at91_set_A_periph(AT91_PIN_PC25, 1);
-		at91_set_A_periph(AT91_PIN_PC26, 1);
-		at91_set_A_periph(AT91_PIN_PC27, 1);
-	}
-
-	mmc_data = *data;
-	platform_device_register(&at572d940hf_mmc_device);
-}
-#else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE	AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
-	{
-		.start	= NAND_BASE,
-		.end	= NAND_BASE + SZ_256M - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at572d940hf_nand_device = {
-	.name		= "atmel_nand",
-	.id		= -1,
-	.dev		= {
-				.platform_data	= &nand_data,
-	},
-	.resource	= nand_resources,
-	.num_resources	= ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
-	unsigned long csa;
-
-	if (!data)
-		return;
-
-	csa = at91_sys_read(AT91_MATRIX_EBICSA);
-	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
-
-	/* enable pin */
-	if (data->enable_pin)
-		at91_set_gpio_output(data->enable_pin, 1);
-
-	/* ready/busy pin */
-	if (data->rdy_pin)
-		at91_set_gpio_input(data->rdy_pin, 1);
-
-	/* card detect pin */
-	if (data->det_pin)
-		at91_set_gpio_input(data->det_pin, 1);
-
-	at91_set_A_periph(AT91_PIN_PB28, 0);		/* A[22] */
-	at91_set_B_periph(AT91_PIN_PA28, 0);		/* NANDOE */
-	at91_set_B_periph(AT91_PIN_PA29, 0);		/* NANDWE */
-
-	nand_data = *data;
-	platform_device_register(&at572d940hf_nand_device);
-}
-
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
-	.sda_pin		= AT91_PIN_PC7,
-	.sda_is_open_drain	= 1,
-	.scl_pin		= AT91_PIN_PC8,
-	.scl_is_open_drain	= 1,
-	.udelay			= 2,		/* ~100 kHz */
-};
-
-static struct platform_device at572d940hf_twi_device {
-	.name			= "i2c-gpio",
-	.id			= -1,
-	.dev.platform_data	= &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	at91_set_GPIO_periph(AT91_PIN_PC7, 1);		/* TWD (SDA) */
-	at91_set_multi_drive(AT91_PIN_PC7, 1);
-
-	at91_set_GPIO_periph(AT91_PIN_PA8, 1);		/* TWCK (SCL) */
-	at91_set_multi_drive(AT91_PIN_PC8, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at572d940hf_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi0_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_TWI0,
-		.end	= AT572D940HF_BASE_TWI0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_TWI0,
-		.end	= AT572D940HF_ID_TWI0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_twi0_device = {
-	.name		= "at91_i2c",
-	.id		= 0,
-	.resource	= twi0_resources,
-	.num_resources	= ARRAY_SIZE(twi0_resources),
-};
-
-static struct resource twi1_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_TWI1,
-		.end	= AT572D940HF_BASE_TWI1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_TWI1,
-		.end	= AT572D940HF_ID_TWI1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_twi1_device = {
-	.name		= "at91_i2c",
-	.id		= 1,
-	.resource	= twi1_resources,
-	.num_resources	= ARRAY_SIZE(twi1_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
-	/* pins used for TWI0 interface */
-	at91_set_A_periph(AT91_PIN_PC7, 0);		/* TWD */
-	at91_set_multi_drive(AT91_PIN_PC7, 1);
-
-	at91_set_A_periph(AT91_PIN_PC8, 0);		/* TWCK */
-	at91_set_multi_drive(AT91_PIN_PC8, 1);
-
-	/* pins used for TWI1 interface */
-	at91_set_A_periph(AT91_PIN_PC20, 0);		/* TWD */
-	at91_set_multi_drive(AT91_PIN_PC20, 1);
-
-	at91_set_A_periph(AT91_PIN_PC21, 0);		/* TWCK */
-	at91_set_multi_drive(AT91_PIN_PC21, 1);
-
-	i2c_register_board_info(0, devices, nr_devices);
-	platform_device_register(&at572d940hf_twi0_device);
-	platform_device_register(&at572d940hf_twi1_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi0_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_SPI0,
-		.end	= AT572D940HF_BASE_SPI0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_SPI0,
-		.end	= AT572D940HF_ID_SPI0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_spi0_device = {
-	.name		= "atmel_spi",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi0_resources,
-	.num_resources	= ARRAY_SIZE(spi0_resources),
-};
-
-static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
-
-static struct resource spi1_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_SPI1,
-		.end	= AT572D940HF_BASE_SPI1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_SPI1,
-		.end	= AT572D940HF_ID_SPI1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_spi1_device = {
-	.name		= "atmel_spi",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &spi_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= spi1_resources,
-	.num_resources	= ARRAY_SIZE(spi1_resources),
-};
-
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PC3, AT91_PIN_PC4, AT91_PIN_PC5, AT91_PIN_PC6 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
-	int i;
-	unsigned long cs_pin;
-	short enable_spi0 = 0;
-	short enable_spi1 = 0;
-
-	/* Choose SPI chip-selects */
-	for (i = 0; i < nr_devices; i++) {
-		if (devices[i].controller_data)
-			cs_pin = (unsigned long) devices[i].controller_data;
-		else if (devices[i].bus_num == 0)
-			cs_pin = spi0_standard_cs[devices[i].chip_select];
-		else
-			cs_pin = spi1_standard_cs[devices[i].chip_select];
-
-		if (devices[i].bus_num == 0)
-			enable_spi0 = 1;
-		else
-			enable_spi1 = 1;
-
-		/* enable chip-select pin */
-		at91_set_gpio_output(cs_pin, 1);
-
-		/* pass chip-select pin to driver */
-		devices[i].controller_data = (void *) cs_pin;
-	}
-
-	spi_register_board_info(devices, nr_devices);
-
-	/* Configure SPI bus(es) */
-	if (enable_spi0) {
-		at91_set_A_periph(AT91_PIN_PA0, 0);	/* SPI0_MISO */
-		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
-		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
-
-		platform_device_register(&at572d940hf_spi0_device);
-	}
-	if (enable_spi1) {
-		at91_set_A_periph(AT91_PIN_PC0, 0);	/* SPI1_MISO */
-		at91_set_A_periph(AT91_PIN_PC1, 0);	/* SPI1_MOSI */
-		at91_set_A_periph(AT91_PIN_PC2, 0);	/* SPI1_SPCK */
-
-		platform_device_register(&at572d940hf_spi1_device);
-	}
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  Timer/Counter blocks
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_TCB,
-		.end	= AT572D940HF_BASE_TCB + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_TC0,
-		.end	= AT572D940HF_ID_TC0,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start	= AT572D940HF_ID_TC1,
-		.end	= AT572D940HF_ID_TC1,
-		.flags	= IORESOURCE_IRQ,
-	},
-	[3] = {
-		.start	= AT572D940HF_ID_TC2,
-		.end	= AT572D940HF_ID_TC2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at572d940hf_tcb_device = {
-	.name		= "atmel_tcb",
-	.id		= 0,
-	.resource	= tcb_resources,
-	.num_resources	= ARRAY_SIZE(tcb_resources),
-};
-
-static void __init at91_add_device_tc(void)
-{
-	platform_device_register(&at572d940hf_tcb_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- *  RTT
- * -------------------------------------------------------------------- */
-
-static struct resource rtt_resources[] = {
-	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device at572d940hf_rtt_device = {
-	.name		= "at91_rtt",
-	.id		= 0,
-	.resource	= rtt_resources,
-	.num_resources	= ARRAY_SIZE(rtt_resources),
-};
-
-static void __init at91_add_device_rtt(void)
-{
-	platform_device_register(&at572d940hf_rtt_device);
-}
-
-
-/* --------------------------------------------------------------------
- *  Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
-static struct platform_device at572d940hf_wdt_device = {
-	.name		= "at91_wdt",
-	.id		= -1,
-	.num_resources	= 0,
-};
-
-static void __init at91_add_device_watchdog(void)
-{
-	platform_device_register(&at572d940hf_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-static struct resource dbgu_resources[] = {
-	[0] = {
-		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
-		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT91_ID_SYS,
-		.end	= AT91_ID_SYS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data dbgu_data = {
-	.use_dma_tx	= 0,
-	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
-	.regs		= (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at572d940hf_dbgu_device = {
-	.name		= "atmel_usart",
-	.id		= 0,
-	.dev		= {
-				.dma_mask		= &dbgu_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &dbgu_data,
-	},
-	.resource	= dbgu_resources,
-	.num_resources	= ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
-	at91_set_A_periph(AT91_PIN_PC31, 1);		/* DTXD */
-	at91_set_A_periph(AT91_PIN_PC30, 0);		/* DRXD */
-}
-
-static struct resource uart0_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_US0,
-		.end	= AT572D940HF_BASE_US0 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_US0,
-		.end	= AT572D940HF_ID_US0,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart0_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at572d940hf_uart0_device = {
-	.name		= "atmel_usart",
-	.id		= 1,
-	.dev		= {
-				.dma_mask		= &uart0_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart0_data,
-	},
-	.resource	= uart0_resources,
-	.num_resources	= ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PA8, 1);		/* TXD0 */
-	at91_set_A_periph(AT91_PIN_PA7, 0);		/* RXD0 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PA10, 0);	/* RTS0 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PA9, 0);	/* CTS0 */
-}
-
-static struct resource uart1_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_US1,
-		.end	= AT572D940HF_BASE_US1 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_US1,
-		.end	= AT572D940HF_ID_US1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart1_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at572d940hf_uart1_device = {
-	.name		= "atmel_usart",
-	.id		= 2,
-	.dev		= {
-				.dma_mask		= &uart1_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart1_data,
-	},
-	.resource	= uart1_resources,
-	.num_resources	= ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PC10, 1);		/* TXD1 */
-	at91_set_A_periph(AT91_PIN_PC9 , 0);		/* RXD1 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PC12, 0);	/* RTS1 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PC11, 0);	/* CTS1 */
-}
-
-static struct resource uart2_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_BASE_US2,
-		.end	= AT572D940HF_BASE_US2 + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= AT572D940HF_ID_US2,
-		.end	= AT572D940HF_ID_US2,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct atmel_uart_data uart2_data = {
-	.use_dma_tx	= 1,
-	.use_dma_rx	= 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at572d940hf_uart2_device = {
-	.name		= "atmel_usart",
-	.id		= 3,
-	.dev		= {
-				.dma_mask		= &uart2_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &uart2_data,
-	},
-	.resource	= uart2_resources,
-	.num_resources	= ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
-	at91_set_A_periph(AT91_PIN_PC15, 1);		/* TXD2 */
-	at91_set_A_periph(AT91_PIN_PC14, 0);		/* RXD2 */
-
-	if (pins & ATMEL_UART_RTS)
-		at91_set_A_periph(AT91_PIN_PC17, 0);	/* RTS2 */
-	if (pins & ATMEL_UART_CTS)
-		at91_set_A_periph(AT91_PIN_PC16, 0);	/* CTS2 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
-struct platform_device *atmel_default_console_device;	/* the serial console device */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
-	struct platform_device *pdev;
-	struct atmel_uart_data *pdata;
-
-	switch (id) {
-		case 0:		/* DBGU */
-			pdev = &at572d940hf_dbgu_device;
-			configure_dbgu_pins();
-			break;
-		case AT572D940HF_ID_US0:
-			pdev = &at572d940hf_uart0_device;
-			configure_usart0_pins(pins);
-			break;
-		case AT572D940HF_ID_US1:
-			pdev = &at572d940hf_uart1_device;
-			configure_usart1_pins(pins);
-			break;
-		case AT572D940HF_ID_US2:
-			pdev = &at572d940hf_uart2_device;
-			configure_usart2_pins(pins);
-			break;
-		default:
-			return;
-	}
-	pdata = pdev->dev.platform_data;
-	pdata->num = portnr;		/* update to mapped ID */
-
-	if (portnr < ATMEL_MAX_UART)
-		at91_uarts[portnr] = pdev;
-}
-
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at572d940hf_set_console_clock(portnr);
-	}
-}
-
-void __init at91_add_device_serial(void)
-{
-	int i;
-
-	for (i = 0; i < ATMEL_MAX_UART; i++) {
-		if (at91_uarts[i])
-			platform_device_register(at91_uarts[i]);
-	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
-}
-
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  mAgic
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_MAGICV
-static struct resource mAgic_resources[] = {
-	{
-		.start = AT91_MAGIC_PM_BASE,
-		.end   = AT91_MAGIC_PM_BASE + AT91_MAGIC_PM_SIZE - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = AT91_MAGIC_DM_I_BASE,
-		.end   = AT91_MAGIC_DM_I_BASE + AT91_MAGIC_DM_I_SIZE - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = AT91_MAGIC_DM_F_BASE,
-		.end   = AT91_MAGIC_DM_F_BASE + AT91_MAGIC_DM_F_SIZE - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = AT91_MAGIC_DM_DB_BASE,
-		.end   = AT91_MAGIC_DM_DB_BASE + AT91_MAGIC_DM_DB_SIZE - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = AT91_MAGIC_REGS_BASE,
-		.end   = AT91_MAGIC_REGS_BASE + AT91_MAGIC_REGS_SIZE - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = AT91_MAGIC_EXTPAGE_BASE,
-		.end   = AT91_MAGIC_EXTPAGE_BASE + AT91_MAGIC_EXTPAGE_SIZE - 1,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start  = AT572D940HF_ID_MSIRQ0,
-		.end    = AT572D940HF_ID_MSIRQ0,
-		.flags  = IORESOURCE_IRQ,
-	},
-	{
-		.start  = AT572D940HF_ID_MHALT,
-		.end    = AT572D940HF_ID_MHALT,
-		.flags  = IORESOURCE_IRQ,
-	},
-	{
-		.start  = AT572D940HF_ID_MEXC,
-		.end    = AT572D940HF_ID_MEXC,
-		.flags  = IORESOURCE_IRQ,
-	},
-	{
-		.start  = AT572D940HF_ID_MEDMA,
-		.end    = AT572D940HF_ID_MEDMA,
-		.flags  = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device mAgic_device = {
-	.name           = "mAgic",
-	.id             = -1,
-	.num_resources  = ARRAY_SIZE(mAgic_resources),
-	.resource       = mAgic_resources,
-};
-
-void __init at91_add_device_mAgic(void)
-{
-	platform_device_register(&mAgic_device);
-}
-#else
-void __init at91_add_device_mAgic(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
-	at91_add_device_rtt();
-	at91_add_device_watchdog();
-	at91_add_device_tc();
-	return 0;
-}
-
-arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91/board-at572d940hf_ek.c b/arch/arm/mach-at91/board-at572d940hf_ek.c
deleted file mode 100644
index dfa896d7d5a9..000000000000
--- a/arch/arm/mach-at91/board-at572d940hf_ek.c
+++ /dev/null
@@ -1,323 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-at572d940hf_ek.c
- *
- * Copyright (C) 2008 Atmel Antonio R. Costa <costa.antonior@gmail.com>
- * Copyright (C) 2005 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ds1305.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/board.h>
-#include <mach/gpio.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init eb_init_early(void)
-{
-	/* Initialize processor: 12.500 MHz crystal */
-	at572d940hf_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx & Tx only) */
-	at91_register_uart(AT572D940HF_ID_US0, 1, 0);
-
-	/* USART1 on ttyS2. (Rx & Tx only) */
-	at91_register_uart(AT572D940HF_ID_US1, 2, 0);
-
-	/* USART2 on ttyS3. (Tx & Rx only */
-	at91_register_uart(AT572D940HF_ID_US2, 3, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-}
-
-static void __init eb_init_irq(void)
-{
-	at572d940hf_init_interrupts(NULL);
-}
-
-
-/*
- * USB Host Port
- */
-static struct at91_usbh_data __initdata eb_usbh_data = {
-	.ports		= 2,
-};
-
-
-/*
- * USB Device Port
- */
-static struct at91_udc_data __initdata eb_udc_data = {
-	.vbus_pin	= 0,		/* no VBUS detection,UDC always on */
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct at91_mmc_data __initdata eb_mmc_data = {
-	.wire4		= 1,
-/*	.det_pin	= ... not connected */
-/*	.wp_pin		= ... not connected */
-/*	.vcc_pin	= ... not connected */
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct at91_eth_data __initdata eb_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PB25,
-	.is_rmii	= 1,
-};
-
-/*
- * NOR flash
- */
-
-static struct mtd_partition eb_nor_partitions[] = {
-	{
-		.name		= "Raw Environment",
-		.offset		= 0,
-		.size		= SZ_4M,
-		.mask_flags	= 0,
-	},
-	{
-		.name		= "OS FS",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 3 * SZ_1M,
-		.mask_flags	= 0,
-	},
-	{
-		.name		= "APP FS",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= 0,
-	},
-};
-
-static void nor_flash_set_vpp(struct map_info* mi, int i) {
-};
-
-static struct physmap_flash_data nor_flash_data = {
-	.width		= 4,
-	.parts		= eb_nor_partitions,
-	.nr_parts	= ARRAY_SIZE(eb_nor_partitions),
-	.set_vpp	= nor_flash_set_vpp,
-};
-
-static struct resource nor_flash_resources[] = {
-	{
-		.start	= AT91_CHIPSELECT_0,
-		.end	= AT91_CHIPSELECT_0 + SZ_16M - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device nor_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data = &nor_flash_data,
-			},
-	.resource	= nor_flash_resources,
-	.num_resources	= ARRAY_SIZE(nor_flash_resources),
-};
-
-static struct sam9_smc_config __initdata eb_nor_smc_config = {
-	.ncs_read_setup		= 1,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 1,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 7,
-	.nrd_pulse		= 7,
-	.ncs_write_pulse	= 7,
-	.nwe_pulse		= 7,
-
-	.read_cycle		= 9,
-	.write_cycle		= 9,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_32,
-	.tdf_cycles		= 1,
-};
-
-static void __init eb_add_device_nor(void)
-{
-	/* configure chip-select 0 (NOR) */
-	sam9_smc_configure(0, &eb_nor_smc_config);
-	platform_device_register(&nor_flash);
-}
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata eb_nand_partition[] = {
-	{
-		.name	= "Partition 1",
-		.offset	= 0,
-		.size	= SZ_16M,
-	},
-	{
-		.name	= "Partition 2",
-		.offset = MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	}
-};
-
-static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-{
-	*num_partitions = ARRAY_SIZE(eb_nand_partition);
-	return eb_nand_partition;
-}
-
-static struct atmel_nand_data __initdata eb_nand_data = {
-	.ale		= 22,
-	.cle		= 21,
-/*	.det_pin	= ... not connected */
-/*	.rdy_pin	= AT91_PIN_PC16, */
-	.enable_pin	= AT91_PIN_PA15,
-	.partition_info	= nand_partitions,
-};
-
-static struct sam9_smc_config __initdata eb_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 0,
-	.ncs_write_setup	= 1,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 12,
-};
-
-static void __init eb_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = !board_have_nand_8bit();
-	/* setup bus-width (8 or 16) */
-	if (eb_nand_data.bus_width_16)
-		eb_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		eb_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &eb_nand_smc_config);
-
-	at91_add_device_nand(&eb_nand_data);
-}
-
-
-/*
- * SPI devices
- */
-static struct resource rtc_resources[] = {
-	[0] = {
-		.start	= AT572D940HF_ID_IRQ1,
-		.end	= AT572D940HF_ID_IRQ1,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct ds1305_platform_data ds1306_data = {
-	.is_ds1306	= true,
-	.en_1hz		= false,
-};
-
-static struct spi_board_info eb_spi_devices[] = {
-	{	/* RTC Dallas DS1306 */
-		.modalias	= "rtc-ds1305",
-		.chip_select	= 3,
-		.mode		= SPI_CS_HIGH | SPI_CPOL | SPI_CPHA,
-		.max_speed_hz	= 500000,
-		.bus_num	= 0,
-		.irq		= AT572D940HF_ID_IRQ1,
-		.platform_data	= (void *) &ds1306_data,
-	},
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* Dataflash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-};
-
-static void __init eb_board_init(void)
-{
-	/* Serial */
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&eb_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&eb_udc_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* NOR */
-	eb_add_device_nor();
-	/* NAND */
-	eb_add_device_nand();
-	/* SPI */
-	at91_add_device_spi(eb_spi_devices, ARRAY_SIZE(eb_spi_devices));
-	/* MMC */
-	at91_add_device_mmc(0, &eb_mmc_data);
-	/* Ethernet */
-	at91_add_device_eth(&eb_eth_data);
-	/* mAgic */
-	at91_add_device_mAgic();
-}
-
-MACHINE_START(AT572D940HFEB, "Atmel AT91D940HF-EB")
-	/* Maintainer: Atmel <costa.antonior@gmail.com> */
-	.timer		= &at91sam926x_timer,
-	.map_io		= at572d940hf_map_io,
-	.init_early	= eb_init_early,
-	.init_irq	= eb_init_irq,
-	.init_machine	= eb_board_init,
-MACHINE_END
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index ac103cbdbf35..61873f3aa92d 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -599,7 +599,7 @@ static void __init at91_pllb_usbfs_clock_init(unsigned long main_clock)
 		at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
 	} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() ||
 		   cpu_is_at91sam9263() || cpu_is_at91sam9g20() ||
-		   cpu_is_at91sam9g10() || cpu_is_at572d940hf()) {
+		   cpu_is_at91sam9g10()) {
 		uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
 		udpck.pmc_mask = AT91SAM926x_PMC_UDP;
 	} else if (cpu_is_at91cap9()) {
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
index 5783bd1b6c40..8ff3418f3430 100644
--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -19,7 +19,6 @@ extern void __init at91sam9rl_map_io(void);
 extern void __init at91sam9g45_map_io(void);
 extern void __init at91x40_map_io(void);
 extern void __init at91cap9_map_io(void);
-extern void __init at572d940hf_map_io(void);
 
  /* Processors */
 extern void __init at91rm9200_set_type(int type);
@@ -31,7 +30,6 @@ extern void __init at91sam9rl_initialize(unsigned long main_clock);
 extern void __init at91sam9g45_initialize(unsigned long main_clock);
 extern void __init at91x40_initialize(unsigned long main_clock);
 extern void __init at91cap9_initialize(unsigned long main_clock);
-extern void __init at572d940hf_initialize(unsigned long main_clock);
 
  /* Interrupts */
 extern void __init at91rm9200_init_interrupts(unsigned int priority[]);
@@ -42,7 +40,6 @@ extern void __init at91sam9rl_init_interrupts(unsigned int priority[]);
 extern void __init at91sam9g45_init_interrupts(unsigned int priority[]);
 extern void __init at91x40_init_interrupts(unsigned int priority[]);
 extern void __init at91cap9_init_interrupts(unsigned int priority[]);
-extern void __init at572d940hf_init_interrupts(unsigned int priority[]);
 extern void __init at91_aic_init(unsigned int priority[]);
 
  /* Timer */
@@ -65,7 +62,6 @@ extern void __init at91sam9263_set_console_clock(int id);
 extern void __init at91sam9rl_set_console_clock(int id);
 extern void __init at91sam9g45_set_console_clock(int id);
 extern void __init at91cap9_set_console_clock(int id);
-extern void __init at572d940hf_set_console_clock(int id);
 struct device;
 
  /* Power Management */
diff --git a/arch/arm/mach-at91/include/mach/at572d940hf.h b/arch/arm/mach-at91/include/mach/at572d940hf.h
deleted file mode 100644
index a738dc7e5d44..000000000000
--- a/arch/arm/mach-at91/include/mach/at572d940hf.h
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * include/mach/at572d940hf.h
- *
- * Antonio R. Costa <costa.antonior@gmail.com>
- * Copyright (C) 2008 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#ifndef AT572D940HF_H
-#define AT572D940HF_H
-
-/*
- * Peripheral identifiers/interrupts.
- */
-#define AT572D940HF_ID_PIOA	2	/* Parallel IO Controller A */
-#define AT572D940HF_ID_PIOB	3	/* Parallel IO Controller B */
-#define AT572D940HF_ID_PIOC	4	/* Parallel IO Controller C */
-#define AT572D940HF_ID_EMAC	5	/* MACB ethernet controller */
-#define AT572D940HF_ID_US0	6	/* USART 0 */
-#define AT572D940HF_ID_US1	7	/* USART 1 */
-#define AT572D940HF_ID_US2	8	/* USART 2 */
-#define AT572D940HF_ID_MCI	9	/* Multimedia Card Interface */
-#define AT572D940HF_ID_UDP	10	/* USB Device Port */
-#define AT572D940HF_ID_TWI0	11	/* Two-Wire Interface 0 */
-#define AT572D940HF_ID_SPI0	12	/* Serial Peripheral Interface 0 */
-#define AT572D940HF_ID_SPI1	13	/* Serial Peripheral Interface 1 */
-#define AT572D940HF_ID_SSC0	14	/* Serial Synchronous Controller 0 */
-#define AT572D940HF_ID_SSC1	15	/* Serial Synchronous Controller 1 */
-#define AT572D940HF_ID_SSC2	16	/* Serial Synchronous Controller 2 */
-#define AT572D940HF_ID_TC0	17	/* Timer Counter 0 */
-#define AT572D940HF_ID_TC1	18	/* Timer Counter 1 */
-#define AT572D940HF_ID_TC2	19	/* Timer Counter 2 */
-#define AT572D940HF_ID_UHP	20	/* USB Host port */
-#define AT572D940HF_ID_SSC3	21	/* Serial Synchronous Controller 3 */
-#define AT572D940HF_ID_TWI1	22	/* Two-Wire Interface 1 */
-#define AT572D940HF_ID_CAN0	23	/* CAN Controller 0 */
-#define AT572D940HF_ID_CAN1	24	/* CAN Controller 1 */
-#define AT572D940HF_ID_MHALT	25	/* mAgicV HALT line */
-#define AT572D940HF_ID_MSIRQ0	26	/* mAgicV SIRQ0 line */
-#define AT572D940HF_ID_MEXC	27	/* mAgicV exception line */
-#define AT572D940HF_ID_MEDMA	28	/* mAgicV end of DMA line */
-#define AT572D940HF_ID_IRQ0	29	/* External Interrupt Source (IRQ0) */
-#define AT572D940HF_ID_IRQ1	30	/* External Interrupt Source (IRQ1) */
-#define AT572D940HF_ID_IRQ2	31	/* External Interrupt Source (IRQ2) */
-
-
-/*
- * User Peripheral physical base addresses.
- */
-#define AT572D940HF_BASE_TCB	0xfffa0000
-#define AT572D940HF_BASE_TC0	0xfffa0000
-#define AT572D940HF_BASE_TC1	0xfffa0040
-#define AT572D940HF_BASE_TC2	0xfffa0080
-#define AT572D940HF_BASE_UDP	0xfffa4000
-#define AT572D940HF_BASE_MCI	0xfffa8000
-#define AT572D940HF_BASE_TWI0	0xfffac000
-#define AT572D940HF_BASE_US0	0xfffb0000
-#define AT572D940HF_BASE_US1	0xfffb4000
-#define AT572D940HF_BASE_US2	0xfffb8000
-#define AT572D940HF_BASE_SSC0	0xfffbc000
-#define AT572D940HF_BASE_SSC1	0xfffc0000
-#define AT572D940HF_BASE_SSC2	0xfffc4000
-#define AT572D940HF_BASE_SPI0	0xfffc8000
-#define AT572D940HF_BASE_SPI1	0xfffcc000
-#define AT572D940HF_BASE_SSC3	0xfffd0000
-#define AT572D940HF_BASE_TWI1	0xfffd4000
-#define AT572D940HF_BASE_EMAC	0xfffd8000
-#define AT572D940HF_BASE_CAN0	0xfffdc000
-#define AT572D940HF_BASE_CAN1	0xfffe0000
-#define AT91_BASE_SYS		0xffffea00
-
-
-/*
- * System Peripherals (offset from AT91_BASE_SYS)
- */
-#define AT91_SDRAMC0	(0xffffea00 - AT91_BASE_SYS)
-#define AT91_SMC	(0xffffec00 - AT91_BASE_SYS)
-#define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
-#define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
-#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
-#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
-
-#define AT91_USART0	AT572D940HF_ID_US0
-#define AT91_USART1	AT572D940HF_ID_US1
-#define AT91_USART2	AT572D940HF_ID_US2
-
-
-/*
- * Internal Memory.
- */
-#define AT572D940HF_SRAM_BASE	0x00300000	/* Internal SRAM base address */
-#define AT572D940HF_SRAM_SIZE	(48 * SZ_1K)	/* Internal SRAM size (48Kb) */
-
-#define AT572D940HF_ROM_BASE	0x00400000	/* Internal ROM base address */
-#define AT572D940HF_ROM_SIZE	SZ_32K		/* Internal ROM size (32Kb) */
-
-#define AT572D940HF_UHP_BASE	0x00500000	/* USB Host controller */
-
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at572d940hf_matrix.h b/arch/arm/mach-at91/include/mach/at572d940hf_matrix.h
deleted file mode 100644
index b6751df09488..000000000000
--- a/arch/arm/mach-at91/include/mach/at572d940hf_matrix.h
+++ /dev/null
@@ -1,123 +0,0 @@
-/*
- * include/mach//at572d940hf_matrix.h
- *
- * Antonio R. Costa <costa.antonior@gmail.com>
- * Copyright (C) 2008 Atmel
- *
- * Copyright (C) 2005 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#ifndef AT572D940HF_MATRIX_H
-#define AT572D940HF_MATRIX_H
-
-#define AT91_MATRIX_MCFG0	(AT91_MATRIX + 0x00)	/* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1	(AT91_MATRIX + 0x04)	/* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2	(AT91_MATRIX + 0x08)	/* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3	(AT91_MATRIX + 0x0C)	/* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4	(AT91_MATRIX + 0x10)	/* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5	(AT91_MATRIX + 0x14)	/* Master Configuration Register 5 */
-
-#define		AT91_MATRIX_ULBT	(7 << 0)	/* Undefined Length Burst Type */
-#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
-#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
-#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
-#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
-#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
-
-#define AT91_MATRIX_SCFG0	(AT91_MATRIX + 0x40)	/* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1	(AT91_MATRIX + 0x44)	/* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2	(AT91_MATRIX + 0x48)	/* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3	(AT91_MATRIX + 0x4C)	/* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4	(AT91_MATRIX + 0x50)	/* Slave Configuration Register 4 */
-#define		AT91_MATRIX_SLOT_CYCLE		(0xff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
-#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
-#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
-#define		AT91_MATRIX_FIXED_DEFMSTR	(0x7  << 18)	/* Fixed Index of Default Master */
-#define		AT91_MATRIX_ARBT		(3    << 24)	/* Arbitration Type */
-#define			AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
-#define			AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
-
-#define AT91_MATRIX_PRAS0	(AT91_MATRIX + 0x80)	/* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRAS1	(AT91_MATRIX + 0x88)	/* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRAS2	(AT91_MATRIX + 0x90)	/* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRAS3	(AT91_MATRIX + 0x98)	/* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRAS4	(AT91_MATRIX + 0xA0)	/* Priority Register A for Slave 4 */
-
-#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
-#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
-#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
-#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
-#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
-#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
-#define		AT91_MATRIX_M6PR		(3 << 24)	/* Master 6 Priority */
-
-#define AT91_MATRIX_MRCR	(AT91_MATRIX + 0x100)	/* Master Remap Control Register */
-#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
-#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-
-#define AT91_MATRIX_SFR0	(AT91_MATRIX + 0x110)	/* Special Function Register 0 */
-#define AT91_MATRIX_SFR1	(AT91_MATRIX + 0x114)	/* Special Function Register 1 */
-#define AT91_MATRIX_SFR2	(AT91_MATRIX + 0x118)	/* Special Function Register 2 */
-#define AT91_MATRIX_SFR3	(AT91_MATRIX + 0x11C)	/* Special Function Register 3 */
-#define AT91_MATRIX_SFR4	(AT91_MATRIX + 0x120)	/* Special Function Register 4 */
-#define AT91_MATRIX_SFR5	(AT91_MATRIX + 0x124)	/* Special Function Register 5 */
-#define AT91_MATRIX_SFR6	(AT91_MATRIX + 0x128)	/* Special Function Register 6 */
-#define AT91_MATRIX_SFR7	(AT91_MATRIX + 0x12C)	/* Special Function Register 7 */
-#define AT91_MATRIX_SFR8	(AT91_MATRIX + 0x130)	/* Special Function Register 8 */
-#define AT91_MATRIX_SFR9	(AT91_MATRIX + 0x134)	/* Special Function Register 9 */
-#define AT91_MATRIX_SFR10	(AT91_MATRIX + 0x138)	/* Special Function Register 10 */
-#define AT91_MATRIX_SFR11	(AT91_MATRIX + 0x13C)	/* Special Function Register 11 */
-#define AT91_MATRIX_SFR12	(AT91_MATRIX + 0x140)	/* Special Function Register 12 */
-#define AT91_MATRIX_SFR13	(AT91_MATRIX + 0x144)	/* Special Function Register 13 */
-#define AT91_MATRIX_SFR14	(AT91_MATRIX + 0x148)	/* Special Function Register 14 */
-#define AT91_MATRIX_SFR15	(AT91_MATRIX + 0x14C)	/* Special Function Register 15 */
-
-
-/*
- * The following registers / bits are not defined in the Datasheet (Revision A)
- */
-
-#define AT91_MATRIX_TCR		(AT91_MATRIX + 0x100)	/* TCM Configuration Register */
-#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
-#define			AT91_MATRIX_ITCM_0		(0 << 0)
-#define			AT91_MATRIX_ITCM_16		(5 << 0)
-#define			AT91_MATRIX_ITCM_32		(6 << 0)
-#define			AT91_MATRIX_ITCM_64		(7 << 0)
-#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
-#define			AT91_MATRIX_DTCM_0		(0 << 4)
-#define			AT91_MATRIX_DTCM_16		(5 << 4)
-#define			AT91_MATRIX_DTCM_32		(6 << 4)
-#define			AT91_MATRIX_DTCM_64		(7 << 4)
-
-#define AT91_MATRIX_EBICSA	(AT91_MATRIX + 0x11C)	/* EBI Chip Select Assignment Register */
-#define		AT91_MATRIX_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_CS3A_SMC_SMARTMEDIA	(1 << 3)
-#define		AT91_MATRIX_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
-#define			AT91_MATRIX_CS4A_SMC		(0 << 4)
-#define			AT91_MATRIX_CS4A_SMC_CF1	(1 << 4)
-#define		AT91_MATRIX_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
-#define			AT91_MATRIX_CS5A_SMC		(0 << 5)
-#define			AT91_MATRIX_CS5A_SMC_CF2	(1 << 5)
-#define		AT91_MATRIX_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index c44e94e22857..ed544a0d5a1d 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -90,7 +90,7 @@ struct at91_eth_data {
 extern void __init at91_add_device_eth(struct at91_eth_data *data);
 
 #if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
-	|| defined(CONFIG_ARCH_AT91SAM9G45) || defined(CONFIG_ARCH_AT572D940HF)
+	|| defined(CONFIG_ARCH_AT91SAM9G45)
 #define eth_platform_data	at91_eth_data
 #endif
 
@@ -204,9 +204,6 @@ extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
 extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
 extern void __init at91_pwm_leds(struct gpio_led *leds, int nr);
 
- /* AT572D940HF DSP */
-extern void __init at91_add_device_mAgic(void);
-
 /* FIXME: this needs a better location, but gets stuff building again */
 extern int at91_suspend_entering_slow_clock(void);
 
diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h
index ab00372ca045..df966c2bc2d4 100644
--- a/arch/arm/mach-at91/include/mach/cpu.h
+++ b/arch/arm/mach-at91/include/mach/cpu.h
@@ -34,8 +34,6 @@
 #define ARCH_ID_AT91SAM9XE256	0x329a93a0
 #define ARCH_ID_AT91SAM9XE512	0x329aa3a0
 
-#define ARCH_ID_AT572D940HF	0x0e0303e0
-
 #define ARCH_ID_AT91M40800	0x14080044
 #define ARCH_ID_AT91R40807	0x44080746
 #define ARCH_ID_AT91M40807	0x14080745
@@ -188,12 +186,6 @@ extern int rm9200_type;
 #define cpu_is_at91cap9_revC()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT572D940HF
-#define cpu_is_at572d940hf() (at91_cpu_identify() == ARCH_ID_AT572D940HF)
-#else
-#define cpu_is_at572d940hf() (0)
-#endif
-
 /*
  * Since this is ARM, we will never run on any AVR32 CPU. But these
  * definitions may reduce clutter in common drivers.
diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h
index 469d3af5a551..1008b9fb5074 100644
--- a/arch/arm/mach-at91/include/mach/hardware.h
+++ b/arch/arm/mach-at91/include/mach/hardware.h
@@ -32,8 +32,6 @@
 #include <mach/at91cap9.h>
 #elif defined(CONFIG_ARCH_AT91X40)
 #include <mach/at91x40.h>
-#elif defined(CONFIG_ARCH_AT572D940HF)
-#include <mach/at572d940hf.h>
 #else
 #error "Unsupported AT91 processor"
 #endif
diff --git a/arch/arm/mach-at91/include/mach/timex.h b/arch/arm/mach-at91/include/mach/timex.h
index 05a6e8af80c4..31ac2d97f14c 100644
--- a/arch/arm/mach-at91/include/mach/timex.h
+++ b/arch/arm/mach-at91/include/mach/timex.h
@@ -82,11 +82,6 @@
 #define AT91X40_MASTER_CLOCK	40000000
 #define CLOCK_TICK_RATE		(AT91X40_MASTER_CLOCK)
 
-#elif defined(CONFIG_ARCH_AT572D940HF)
-
-#define AT572D940HF_MASTER_CLOCK	80000000
-#define CLOCK_TICK_RATE		(AT572D940HF_MASTER_CLOCK/16)
-
 #endif
 
 #endif