PCI: designware: Split Exynos and i.MX bindings

The glue around the core designware IP is significantly different between
the Exynos and i.MX implementation, which is reflected in the DT bindings.

This changes the i.MX6 binding to reuse as much as possible from the common
designware binding and removes old cruft.

I removed the optional GPIOs with the following reasoning:
- disable-gpio: endpoint specific GPIO, not currently wired up in any code.
  Should be handled by the PCI device driver, not the host controller
  driver.
- wake-up-gpio: same as above.
- power-on-gpio: No user in any upstream DT.  This should be handled by a
  regulator which shouldn't be controlled by the host driver, but rather by
  the PCI device driver.

[bhelgaas: whitespace fixes]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

1 files changed, 6 insertions, 68 deletions

diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt
index d6fae13ff062..d0d15ee42834 100644
--- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
@@ -1,15 +1,7 @@
 * Synopsys Designware PCIe interface
 
 Required properties:
-- compatible: should contain "snps,dw-pcie" to identify the
-	core, plus an identifier for the specific instance, such
-	as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie".
-- reg: base addresses and lengths of the pcie controller,
-	the phy controller, additional register for the phy controller.
-- interrupts: interrupt values for level interrupt,
-	pulse interrupt, special interrupt.
-- clocks: from common clock binding: handle to pci clock.
-- clock-names: from common clock binding: should be "pcie" and "pcie_bus".
+- compatible: should contain "snps,dw-pcie" to identify the core.
 - #address-cells: set to <3>
 - #size-cells: set to <2>
 - device_type: set to "pci"
@@ -19,65 +11,11 @@ Required properties:
 	to define the mapping of the PCIe interface to interrupt
 	numbers.
 - num-lanes: number of lanes to use
+- clocks: Must contain an entry for each entry in clock-names.
+	See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+	- "pcie"
+	- "pcie_bus"
 
 Optional properties:
 - reset-gpio: gpio pin number of power good signal
-
-Optional properties for fsl,imx6q-pcie
-- power-on-gpio: gpio pin number of power-enable signal
-- wake-up-gpio: gpio pin number of incoming wakeup signal
-- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
-
-Example:
-
-SoC specific DT Entry:
-
-	pcie@290000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x290000 0x1000
-			0x270000 0x1000
-			0x271000 0x40>;
-		interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
-		clocks = <&clock 28>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x40001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0x0 0 &gic 53>;
-		num-lanes = <4>;
-	};
-
-	pcie@2a0000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x2a0000 0x1000
-			0x272000 0x1000
-			0x271040 0x40>;
-		interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
-		clocks = <&clock 29>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x60001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0x0 0 &gic 56>;
-		num-lanes = <4>;
-	};
-
-Board specific DT Entry:
-
-	pcie@290000 {
-		reset-gpio = <&pin_ctrl 5 0>;
-	};
-
-	pcie@2a0000 {
-		reset-gpio = <&pin_ctrl 22 0>;
-	};