Commit message (Collapse) | Author | Age | Files | Lines | |
---|---|---|---|---|---|
* | Add CPU1 ambient sensor and PCIe ambient sensor to fan control ambient ↵ | Raptor Engineering Development Team | 2018-05-13 | 1 | -0/+2 |
| | | | | temperature sensor group on Talos II | ||||
* | Add CPU1 ambient sensor to IPMI SDR on Talos II | Raptor Engineering Development Team | 2018-05-13 | 2 | -0/+23 |
| | |||||
* | Remove unneccessary fan speed maps for chassis fans | Raptor Engineering Development Team | 2018-05-13 | 1 | -16/+2 |
| | | | | Retune PID loop for new sensor locations | ||||
* | Fix ambient temperature sensor mappings on Talos II | Raptor Engineering Development Team | 2018-05-13 | 1 | -2/+3 |
| | | | | | | | Talos has three on-board sensors, two high resolution sensors and one low resolution sensor. The two high resolution sensors are mounted near the front edge of the PCB, to monitor intake temperatures on the card. The low resolution sensor is mounted near the rear of the PCB, in the PCIe card area. | ||||
* | Attempt to detect host power down if watchdog fails | Raptor Engineering Development Team | 2018-05-13 | 1 | -0/+18 |
| | |||||
* | Tweak chassis fan PID controls again to mitigate integrator wind-up | Raptor Engineering Development Team | 2018-05-12 | 1 | -2/+2 |
| | |||||
* | Do not attempt to bind OCC drivers until IPL is complete | Raptor Engineering Development Team | 2018-05-12 | 1 | -0/+8 |
| | |||||
* | Load final manufacturer ID and device ID data into IPMI data fields | Raptor Engineering Development Team | 2018-05-11 | 1 | -1/+1 |
| | |||||
* | Add support for secondary PCIe region ambient temperature sensor on Talos II ↵ | Raptor Engineering Development Team | 2018-05-09 | 3 | -0/+26 |
| | | | | systems | ||||
* | Add initial IPMI sensor mappings for Talos II | Raptor Engineering Development Team | 2018-05-09 | 6 | -0/+1865 |
| | |||||
* | FRU: Add Entity ID in the host FRU inventory yaml | Ratan Gupta | 2018-05-08 | 1 | -0/+6 |
| | | | | | | | | | | | | | | | This commit also adds the entityID and entityInstance property for BMC FRUS config yaml. These attributes are required to pass it through Get SDR command. Currently we support two types of record format through Get SDR 1) FULL Record. 2) FRU Record. Resolves openbmc/openbmc#2823 Change-Id: Ie7424fbc493dde5070a2c65c74ba83565154b9d4 Signed-off-by: Ratan Gupta <ratagupt@in.ibm.com> | ||||
* | Add missing mutability attributes to IPMI inventory YAML | Raptor Engineering Development Team | 2018-05-08 | 1 | -0/+71 |
| | |||||
* | Update IPMI YAML from Romulus source | Raptor Engineering Development Team | 2018-05-08 | 1 | -437/+499 |
| | |||||
* | sensor: Modify config for sensor to add additional fields | Tom Joseph | 2018-05-08 | 2 | -0/+7 |
| | | | | | | | | | | Added entity ID, entity instance and sensor naming pattern to the generated sensor yaml. Resolves openbmc/openbmc#2612 Change-Id: Ie4dc9548833cb30126e873a7597b2be9b1ea7f79 Signed-off-by: Tom Joseph <tomjoseph@in.ibm.com> | ||||
* | Bring boot VDN in line with values in datasheet | Raptor Engineering Development Team | 2018-05-08 | 1 | -1/+1 |
| | | | | | Vdn may be undervolted due to old values in the VRM setup scripts compared with the current datasheet. Use the correct boot voltage to avoid system instability during IPL. | ||||
* | Fix power sequencing on Talos II. | Brandon Bergren | 2018-05-08 | 2 | -0/+4 |
| | | | | | | | | | | | | | | | We need to wait for PGOOD before attempting to run the AVSBus services. Additionally, we want to hold off on reaching the obmc-power-start target until the AVSBus is set up properly, to keep things like fan control from interfering. By declaring these dependencies explicitly, the power sequencing on the BMC side should no longer be sensitive to the time it takes for the FPGA to turn on the voltage regulators, and it should avoid attempting to program the CPU VRMs before they are ready to be programmed. Signed-off-by: Brandon Bergren <git@bdragon.rtk0.net> | ||||
* | Tweak chassis fan PID tuning | Raptor Engineering Development Team | 2018-05-07 | 1 | -2/+2 |
| | | | | This resolves long period integrator-induced oscillations due to proportional gain being too low compared to integrator gain. | ||||
* | Remove broken ASpeed PWM fan and tach driver tie-in | Raptor Engineering Development Team | 2018-05-07 | 2 | -2/+0 |
| | | | | | | The current 4.10 kernel returns a bus error when attempting to read from the ASpeed fan controller tach. This causes a massive amount of systemd spam as the interface continues to attempt to rebind. Disable pending a fix in a newer kernel version. | ||||
* | Back off chassis fan proportional constantraptor-v1.0405-04-2018 | Raptor Engineering Development Team | 2018-05-04 | 1 | -1/+1 |
| | | | | | | | Ambient temperature swings should be slow enough, with a slow enough thermal response from the PCB, to make primary control via integrator viable. This slows down the fan responses and prevents audible "hunting" as the ambient sensor changes value more rapidly than the chassis fans actually need to react. | ||||
* | Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ↵ | Raptor Engineering Development Team | 2018-05-04 | 1 | -7/+7 |
| | | | | the new PID control algorithms | ||||
* | Switch to PID control of main fans | Raptor Engineering Development Team | 2018-04-29 | 1 | -62/+65 |
| | |||||
* | Wait 5 seconds for fans to reach full speed after fan controller init | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+1 |
| | |||||
* | Update fan monitor YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+7 |
| | |||||
* | Update fan event YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -193/+225 |
| | |||||
* | Make decrease symmetric with increase | Raptor Engineering Development Team | 2018-04-28 | 2 | -12/+12 |
| | | | | Note that this verson oscillates badly, a more sophisticated control is needed | ||||
* | Don't set zone 2 to high speed when fewer than 4 chassis fans are installed, ↵ | Raptor Engineering Development Team | 2018-04-28 | 1 | -76/+0 |
| | | | | or when fewer than 4 chassis fans are functional | ||||
* | Tighten up fan response again | Raptor Engineering Development Team | 2018-04-28 | 2 | -15/+15 |
| | |||||
* | Switch openpower-dbus-interfaces to Raptor Computing Systems GIT repository | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+1 |
| | |||||
* | Raise CPU core temp setpoints | Raptor Engineering Development Team | 2018-04-20 | 2 | -71/+71 |
| | | | | | Implement less aggressive fan curve Multiply all base fan speeds by 10 due to recent phosphor-hwmon change | ||||
* | Enhance OCC communication failure error recovery | Raptor Engineering Development Team | 2018-04-14 | 1 | -0/+13 |
| | |||||
* | Revup pdbg | Raptor Engineering Development Team | 2018-04-14 | 1 | -1/+1 |
| | |||||
* | Allow the on-board VGA device to be enabled or disabled based on FPGA jumper ↵ | Raptor Engineering Development Team | 2018-04-14 | 4 | -1/+60 |
| | | | | | | setting readback This requires FPGA version 1.04 or higher to work | ||||
* | Minimize chassis fan hunting with additional fan speed floor mappings in ↵ | Raptor Engineering Development Team | 2018-02-19 | 1 | -7/+13 |
| | | | | common ambent temperature ranges | ||||
* | Adjust floor threshold map to avoid chassis fan hunting at typical ambient ↵ | Raptor Engineering Development Team | 2018-02-19 | 1 | -7/+7 |
| | | | | temperatures | ||||
* | Loosen ambient temperature fan controls somewhat | Raptor Engineering Development Team | 2018-02-19 | 1 | -3/+3 |
| | | | | This lessens hunting due to coarse steps in the ambient sensor resolution | ||||
* | Set chassis fan speeds based on on-board ambient temperature sensor | Raptor Engineering Development Team | 2018-02-19 | 1 | -60/+11 |
| | | | | Remove copypasted GPU temperature sensor blocks | ||||
* | Use hardbeep instead of softbeep on Talos systems | Raptor Engineering Development Team | 2018-01-25 | 1 | -1/+1 |
| | |||||
* | Split fan control zones for CPU0 and CPU1 | Raptor Engineering Development Team | 2018-01-23 | 3 | -22/+93 |
| | | | | This allows fan control to function when only one CPU is installed | ||||
* | Add softbeep packaging files | Raptor Engineering Development Team | 2018-01-22 | 1 | -1/+1 |
| | |||||
* | Reset OCC on error detection | Raptor Engineering Development Team | 2018-01-22 | 1 | -2/+11 |
| | | | | | This fixes a corner case where a hung OCC did not report rising core temperatures and the fans failed to react as a result | ||||
* | Remove DD1 VCS workaround hack | Raptor Engineering Development Team | 2018-01-22 | 9 | -97/+2 |
| | |||||
* | Recover from loss of either OCC | Raptor Engineering Development Team | 2018-01-22 | 1 | -3/+39 |
| | | | | This fixes a corner case where the second OCC could drop off the bus undetected | ||||
* | Restart OCC service before restarting fan controller | Raptor Engineering Development Team | 2018-01-21 | 1 | -2/+17 |
| | | | | This fixes fan control failing on boot due to offline OCC services | ||||
* | Fix incorrect Talos fan control settings | Raptor Engineering Development Team | 2018-01-21 | 3 | -21/+21 |
| | | | | Fan control is now operational on Talos hardware | ||||
* | Enable ambient temperature sensor | Raptor Engineering Development Team | 2018-01-21 | 2 | -0/+2 |
| | |||||
* | Add watchdog mode to OCC enable service | Raptor Engineering Development Team | 2018-01-21 | 2 | -5/+20 |
| | | | | This works around transient OCC communication failure disabling fan control | ||||
* | Enable OCC service after IPL completion | Raptor Engineering Development Team | 2018-01-21 | 2 | -5/+6 |
| | |||||
* | Enable the W83773G driver on Talos systems | Raptor Engineering Development Team | 2018-01-20 | 1 | -0/+1 |
| | |||||
* | Enable Talos IPL monitor LED service | Raptor Engineering Development Team | 2018-01-20 | 1 | -1/+1 |
| | |||||
* | Add IPL status observer | Raptor Engineering Development Team | 2018-01-20 | 1 | -0/+1 |
| |