Commit message (Collapse) | Author | Age | Files | Lines | |
---|---|---|---|---|---|
* | Add initial IPMI sensor mappings for Talos II | Raptor Engineering Development Team | 2019-04-25 | 6 | -0/+1865 |
| | |||||
* | Add missing mutability attributes to IPMI inventory YAML | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+71 |
| | |||||
* | Update IPMI YAML from Romulus source | Raptor Engineering Development Team | 2019-04-25 | 1 | -437/+499 |
| | |||||
* | Bring boot VDN in line with values in datasheet | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| | | | | | Vdn may be undervolted due to old values in the VRM setup scripts compared with the current datasheet. Use the correct boot voltage to avoid system instability during IPL. | ||||
* | Fix power sequencing on Talos II. | Brandon Bergren | 2019-04-25 | 2 | -0/+4 |
| | | | | | | | | | | | | | | | We need to wait for PGOOD before attempting to run the AVSBus services. Additionally, we want to hold off on reaching the obmc-power-start target until the AVSBus is set up properly, to keep things like fan control from interfering. By declaring these dependencies explicitly, the power sequencing on the BMC side should no longer be sensitive to the time it takes for the FPGA to turn on the voltage regulators, and it should avoid attempting to program the CPU VRMs before they are ready to be programmed. Signed-off-by: Brandon Bergren <git@bdragon.rtk0.net> | ||||
* | Tweak chassis fan PID tuning | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+2 |
| | | | | This resolves long period integrator-induced oscillations due to proportional gain being too low compared to integrator gain. | ||||
* | Remove broken ASpeed PWM fan and tach driver tie-in | Raptor Engineering Development Team | 2019-04-25 | 2 | -2/+0 |
| | | | | | | The current 4.10 kernel returns a bus error when attempting to read from the ASpeed fan controller tach. This causes a massive amount of systemd spam as the interface continues to attempt to rebind. Disable pending a fix in a newer kernel version. | ||||
* | Back off chassis fan proportional constant | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| | | | | | | | Ambient temperature swings should be slow enough, with a slow enough thermal response from the PCB, to make primary control via integrator viable. This slows down the fan responses and prevents audible "hunting" as the ambient sensor changes value more rapidly than the chassis fans actually need to react. | ||||
* | Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ↵ | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+7 |
| | | | | the new PID control algorithms | ||||
* | Switch to PID control of main fans | Raptor Engineering Development Team | 2019-04-25 | 1 | -62/+65 |
| | |||||
* | Wait 5 seconds for fans to reach full speed after fan controller init | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| | |||||
* | Update fan monitor YAML to new syntax | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+7 |
| | |||||
* | Update fan event YAML to new syntax | Raptor Engineering Development Team | 2019-04-25 | 1 | -193/+225 |
| | |||||
* | Make decrease symmetric with increase | Raptor Engineering Development Team | 2019-04-25 | 2 | -12/+12 |
| | | | | Note that this verson oscillates badly, a more sophisticated control is needed | ||||
* | Don't set zone 2 to high speed when fewer than 4 chassis fans are installed, ↵ | Raptor Engineering Development Team | 2019-04-25 | 1 | -76/+0 |
| | | | | or when fewer than 4 chassis fans are functional | ||||
* | Tighten up fan response again | Raptor Engineering Development Team | 2019-04-25 | 2 | -15/+15 |
| | |||||
* | Raise CPU core temp setpoints | Raptor Engineering Development Team | 2019-04-25 | 2 | -71/+71 |
| | | | | | Implement less aggressive fan curve Multiply all base fan speeds by 10 due to recent phosphor-hwmon change | ||||
* | Minimize chassis fan hunting with additional fan speed floor mappings in ↵ | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+13 |
| | | | | common ambent temperature ranges | ||||
* | Adjust floor threshold map to avoid chassis fan hunting at typical ambient ↵ | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+7 |
| | | | | temperatures | ||||
* | Loosen ambient temperature fan controls somewhat | Raptor Engineering Development Team | 2019-04-25 | 1 | -3/+3 |
| | | | | This lessens hunting due to coarse steps in the ambient sensor resolution | ||||
* | Set chassis fan speeds based on on-board ambient temperature sensor | Raptor Engineering Development Team | 2019-04-25 | 1 | -60/+11 |
| | | | | Remove copypasted GPU temperature sensor blocks | ||||
* | Use hardbeep instead of softbeep on Talos systems | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| | |||||
* | Split fan control zones for CPU0 and CPU1 | Raptor Engineering Development Team | 2019-04-25 | 3 | -22/+93 |
| | | | | This allows fan control to function when only one CPU is installed | ||||
* | Add softbeep packaging files | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| | |||||
* | Remove DD1 VCS workaround hack | Raptor Engineering Development Team | 2019-04-25 | 6 | -76/+0 |
| | |||||
* | Fix incorrect Talos fan control settings | Raptor Engineering Development Team | 2019-04-25 | 3 | -21/+21 |
| | | | | Fan control is now operational on Talos hardware | ||||
* | Enable ambient temperature sensor | Raptor Engineering Development Team | 2019-04-25 | 2 | -0/+2 |
| | |||||
* | Enable the W83773G driver on Talos systems | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+1 |
| | |||||
* | Enable Talos IPL monitor LED service | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 |
| | |||||
* | Signal BMC ready when BMC has finished booting on Talos systems | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+3 |
| | |||||
* | Initial port of Witherspoon fan control to Talos | Raptor Engineering Development Team | 2019-04-25 | 43 | -7/+2931 |
| | | | | | NOTE: Not yet tested on hardware Mapping likely incorrect | ||||
* | Copy Romulus files to Talos for future development | Raptor Engineering Development Team | 2019-04-19 | 44 | -0/+3433 |
Apply initial renames and conversions to copied sources |