Commit message (Collapse) | Author | Age | Files | Lines | |
---|---|---|---|---|---|
* | Back off chassis fan proportional constantraptor-v1.0405-04-2018 | Raptor Engineering Development Team | 2018-05-04 | 1 | -1/+1 |
| | | | | | | | Ambient temperature swings should be slow enough, with a slow enough thermal response from the PCB, to make primary control via integrator viable. This slows down the fan responses and prevents audible "hunting" as the ambient sensor changes value more rapidly than the chassis fans actually need to react. | ||||
* | Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ↵ | Raptor Engineering Development Team | 2018-05-04 | 1 | -7/+7 |
| | | | | the new PID control algorithms | ||||
* | Revup phosphor-fan | Raptor Engineering Development Team | 2018-05-04 | 1 | -2/+2 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-05-04 | 1 | -2/+2 |
| | |||||
* | Revup linuxraptor-v1.0304-30-2018 | Raptor Engineering Development Team | 2018-04-30 | 1 | -1/+1 |
| | |||||
* | Switch to PID control of main fans | Raptor Engineering Development Team | 2018-04-29 | 1 | -62/+65 |
| | |||||
* | Revup fan control and switch to branch | Raptor Engineering Development Team | 2018-04-29 | 1 | -2/+2 |
| | |||||
* | Wait 5 seconds for fans to reach full speed after fan controller init | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+1 |
| | |||||
* | Update fan monitor YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+7 |
| | |||||
* | Update fan event YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -193/+225 |
| | |||||
* | Revup fan control | Raptor Engineering Development Team | 2018-04-28 | 1 | -2/+2 |
| | |||||
* | Make decrease symmetric with increase | Raptor Engineering Development Team | 2018-04-28 | 2 | -12/+12 |
| | | | | Note that this verson oscillates badly, a more sophisticated control is needed | ||||
* | Don't set zone 2 to high speed when fewer than 4 chassis fans are installed, ↵ | Raptor Engineering Development Team | 2018-04-28 | 1 | -76/+0 |
| | | | | or when fewer than 4 chassis fans are functional | ||||
* | Tighten up fan response again | Raptor Engineering Development Team | 2018-04-28 | 2 | -15/+15 |
| | |||||
* | Switch openpower-dbus-interfaces to Raptor Computing Systems GIT repository | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+1 |
| | |||||
* | ipmi: Add missing build dependencyraptor-v1.0204-19-2018 | Brad Bishop | 2018-04-20 | 1 | -0/+1 |
| | | | | | | | | | Add a missing pyyaml dependency to the phosphor-ipmi-sensor-inventory-mrw-native recipe. Tested: Built a Witherspoon image Change-Id: Ia85eb4da107f855d8f2dd9483b4dd34b71674f24 Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com> | ||||
* | Raise CPU core temp setpoints | Raptor Engineering Development Team | 2018-04-20 | 2 | -71/+71 |
| | | | | | Implement less aggressive fan curve Multiply all base fan speeds by 10 due to recent phosphor-hwmon change | ||||
* | Revup phosphor-hwmon and switch to release 1.02 branch | Raptor Engineering Development Team | 2018-04-20 | 1 | -2/+2 |
| | |||||
* | Switch u-boot to branchraptor-v1.0104-13-2018 | Raptor Engineering Development Team | 2018-04-14 | 1 | -1/+1 |
| | |||||
* | Switch phosphor-hwmon to branch | Raptor Engineering Development Team | 2018-04-14 | 1 | -1/+1 |
| | |||||
* | Switch phsphor-fan to branch | Raptor Engineering Development Team | 2018-04-14 | 1 | -1/+1 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-04-14 | 1 | -2/+2 |
| | | | | Switch skeleton to branch | ||||
* | Enhance OCC communication failure error recovery | Raptor Engineering Development Team | 2018-04-14 | 1 | -0/+13 |
| | |||||
* | Revup pdbg | Raptor Engineering Development Team | 2018-04-14 | 1 | -1/+1 |
| | |||||
* | Allow the on-board VGA device to be enabled or disabled based on FPGA jumper ↵ | Raptor Engineering Development Team | 2018-04-14 | 4 | -1/+60 |
| | | | | | | setting readback This requires FPGA version 1.04 or higher to work | ||||
* | Revup skeletonraptor-v1.0003-26-2018 | Raptor Engineering Development Team | 2018-03-26 | 1 | -1/+1 |
| | |||||
* | Revup linux-obmc | Raptor Engineering Development Team | 2018-03-07 | 1 | -1/+1 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-03-03 | 1 | -1/+1 |
| | |||||
* | Work around upstream BMC bug 2946 | Raptor Engineering Development Team | 2018-03-03 | 2 | -2/+20 |
| | |||||
* | Minimize chassis fan hunting with additional fan speed floor mappings in ↵ | Raptor Engineering Development Team | 2018-02-19 | 1 | -7/+13 |
| | | | | common ambent temperature ranges | ||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-02-19 | 1 | -1/+1 |
| | |||||
* | Adjust floor threshold map to avoid chassis fan hunting at typical ambient ↵ | Raptor Engineering Development Team | 2018-02-19 | 1 | -7/+7 |
| | | | | temperatures | ||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-02-19 | 1 | -1/+1 |
| | |||||
* | Loosen ambient temperature fan controls somewhat | Raptor Engineering Development Team | 2018-02-19 | 1 | -3/+3 |
| | | | | This lessens hunting due to coarse steps in the ambient sensor resolution | ||||
* | Revup u-boot | Raptor Engineering Development Team | 2018-02-19 | 1 | -1/+1 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-02-19 | 1 | -1/+1 |
| | |||||
* | Set chassis fan speeds based on on-board ambient temperature sensor | Raptor Engineering Development Team | 2018-02-19 | 1 | -60/+11 |
| | | | | Remove copypasted GPU temperature sensor blocks | ||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-01-26 | 1 | -1/+1 |
| | |||||
* | Revup obmc-linux | Raptor Engineering Development Team | 2018-01-25 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-fan-presence | Raptor Engineering Development Team | 2018-01-25 | 1 | -1/+1 |
| | |||||
* | Use hardbeep instead of softbeep on Talos systems | Raptor Engineering Development Team | 2018-01-25 | 1 | -1/+1 |
| | |||||
* | Add obmc-hardbeep packaging files | Raptor Engineering Development Team | 2018-01-25 | 1 | -0/+9 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-01-25 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-fan-presence | Raptor Engineering Development Team | 2018-01-24 | 1 | -1/+1 |
| | |||||
* | Split fan control zones for CPU0 and CPU1 | Raptor Engineering Development Team | 2018-01-23 | 3 | -22/+93 |
| | | | | This allows fan control to function when only one CPU is installed | ||||
* | Revup phosphor-fan | Raptor Engineering Development Team | 2018-01-23 | 1 | -1/+1 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-01-23 | 1 | -1/+1 |
| | |||||
* | Add softbeep packaging files | Raptor Engineering Development Team | 2018-01-22 | 2 | -1/+10 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-01-22 | 1 | -1/+1 |
| | |||||
* | Revup obmc-linux | Raptor Engineering Development Team | 2018-01-22 | 1 | -1/+1 |
| |