Commit message (Collapse) | Author | Age | Files | Lines | |
---|---|---|---|---|---|
* | Raise kernel tick rate and forcibly enable hrtimersraptor-v1.0505-11-2018 | Raptor Engineering Development Team | 2018-05-14 | 1 | -0/+10 |
| | | | | | Enable LED PWM support - NOTE: PWM is software driven and not yet suitable for general use | ||||
* | Revup linux-obmc | Raptor Engineering Development Team | 2018-05-14 | 1 | -1/+1 |
| | |||||
* | Delay OCC binding from host boot complete signal | Raptor Engineering Development Team | 2018-05-14 | 1 | -0/+4 |
| | | | | This works around more FSI bus failures due to binding while host skiroot kernel is still starting | ||||
* | Lower chassis ambient set point due to addition of averaged intake sensors | Raptor Engineering Development Team | 2018-05-13 | 1 | -1/+1 |
| | |||||
* | Add CPU1 ambient sensor and PCIe ambient sensor to fan control ambient ↵ | Raptor Engineering Development Team | 2018-05-13 | 1 | -0/+2 |
| | | | | temperature sensor group on Talos II | ||||
* | Add CPU1 ambient sensor to IPMI SDR on Talos II | Raptor Engineering Development Team | 2018-05-13 | 2 | -0/+23 |
| | |||||
* | Remove unneccessary fan speed maps for chassis fans | Raptor Engineering Development Team | 2018-05-13 | 1 | -16/+2 |
| | | | | Retune PID loop for new sensor locations | ||||
* | Fix ambient temperature sensor mappings on Talos II | Raptor Engineering Development Team | 2018-05-13 | 1 | -2/+3 |
| | | | | | | | Talos has three on-board sensors, two high resolution sensors and one low resolution sensor. The two high resolution sensors are mounted near the front edge of the PCB, to monitor intake temperatures on the card. The low resolution sensor is mounted near the rear of the PCB, in the PCIe card area. | ||||
* | Fix README to show correct build environment dependencies | Raptor Engineering Development Team | 2018-05-13 | 1 | -1/+1 |
| | |||||
* | Prevent FSI scan during initial chassis power on and host start | Raptor Engineering Development Team | 2018-05-13 | 2 | -0/+2 |
| | |||||
* | Attempt to detect host power down if watchdog fails | Raptor Engineering Development Team | 2018-05-13 | 1 | -0/+18 |
| | |||||
* | Tweak chassis fan PID controls again to mitigate integrator wind-up | Raptor Engineering Development Team | 2018-05-12 | 1 | -2/+2 |
| | |||||
* | Revup phosphor-ipmi-host | Raptor Engineering Development Team | 2018-05-12 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-ipmi-host | Raptor Engineering Development Team | 2018-05-12 | 1 | -2/+2 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-05-12 | 1 | -2/+2 |
| | |||||
* | Force OCC disable script to have completed execution before host can power on | Raptor Engineering Development Team | 2018-05-12 | 2 | -0/+2 |
| | |||||
* | Do not attempt to bind OCC drivers until IPL is complete | Raptor Engineering Development Team | 2018-05-12 | 1 | -0/+8 |
| | |||||
* | Block chassis poweron and host start on completion of shutdown scripts | Raptor Engineering Development Team | 2018-05-12 | 2 | -0/+2 |
| | |||||
* | Load final manufacturer ID and device ID data into IPMI data fields | Raptor Engineering Development Team | 2018-05-11 | 1 | -1/+1 |
| | |||||
* | Add support for secondary PCIe region ambient temperature sensor on Talos II ↵ | Raptor Engineering Development Team | 2018-05-09 | 3 | -0/+26 |
| | | | | systems | ||||
* | Add initial IPMI sensor mappings for Talos II | Raptor Engineering Development Team | 2018-05-09 | 6 | -0/+1865 |
| | |||||
* | Redirect serverwiz to Raptor Computing Systems repositories | Raptor Engineering Development Team | 2018-05-09 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-net-ipmid | Raptor Engineering Development Team | 2018-05-09 | 1 | -1/+1 |
| | |||||
* | Revup ipmi-fru-parser | Raptor Engineering Development Team | 2018-05-09 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-host-ipmid | Raptor Engineering Development Team | 2018-05-09 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-inventory-manager | Raptor Engineering Development Team | 2018-05-09 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-dbus-interfaces | Raptor Engineering Development Team | 2018-05-09 | 1 | -1/+1 |
| | |||||
* | Revup phosphor-mrw-tools | Raptor Engineering Development Team | 2018-05-09 | 1 | -1/+1 |
| | |||||
* | FRU: Add Entity ID in the host FRU inventory yaml | Ratan Gupta | 2018-05-08 | 1 | -0/+6 |
| | | | | | | | | | | | | | | | This commit also adds the entityID and entityInstance property for BMC FRUS config yaml. These attributes are required to pass it through Get SDR command. Currently we support two types of record format through Get SDR 1) FULL Record. 2) FRU Record. Resolves openbmc/openbmc#2823 Change-Id: Ie7424fbc493dde5070a2c65c74ba83565154b9d4 Signed-off-by: Ratan Gupta <ratagupt@in.ibm.com> | ||||
* | Add missing mutability attributes to IPMI inventory YAML | Raptor Engineering Development Team | 2018-05-08 | 1 | -0/+71 |
| | |||||
* | Update IPMI YAML from Romulus source | Raptor Engineering Development Team | 2018-05-08 | 1 | -437/+499 |
| | |||||
* | phosphor-ipmi-host: Add channel config default | Patrick Venture | 2018-05-08 | 4 | -0/+36 |
| | | | | | | | | To provide a custom channel configuration, provide a virtual phosphor-ipmi-channel-config. Change-Id: I00d8e8aed11a18d193a9066a098611784600da56 Signed-off-by: Patrick Venture <venture@google.com> | ||||
* | sensor: Modify config for sensor to add additional fields | Tom Joseph | 2018-05-08 | 4 | -0/+223 |
| | | | | | | | | | | Added entity ID, entity instance and sensor naming pattern to the generated sensor yaml. Resolves openbmc/openbmc#2612 Change-Id: Ie4dc9548833cb30126e873a7597b2be9b1ea7f79 Signed-off-by: Tom Joseph <tomjoseph@in.ibm.com> | ||||
* | Redirect IPMI parser to Raptor Computing Systems repositories | Raptor Engineering Development Team | 2018-05-08 | 1 | -1/+1 |
| | |||||
* | Bring boot VDN in line with values in datasheet | Raptor Engineering Development Team | 2018-05-08 | 1 | -1/+1 |
| | | | | | Vdn may be undervolted due to old values in the VRM setup scripts compared with the current datasheet. Use the correct boot voltage to avoid system instability during IPL. | ||||
* | Fix power sequencing on Talos II. | Brandon Bergren | 2018-05-08 | 2 | -0/+4 |
| | | | | | | | | | | | | | | | We need to wait for PGOOD before attempting to run the AVSBus services. Additionally, we want to hold off on reaching the obmc-power-start target until the AVSBus is set up properly, to keep things like fan control from interfering. By declaring these dependencies explicitly, the power sequencing on the BMC side should no longer be sensitive to the time it takes for the FPGA to turn on the voltage regulators, and it should avoid attempting to program the CPU VRMs before they are ready to be programmed. Signed-off-by: Brandon Bergren <git@bdragon.rtk0.net> | ||||
* | Tweak chassis fan PID tuning | Raptor Engineering Development Team | 2018-05-07 | 1 | -2/+2 |
| | | | | This resolves long period integrator-induced oscillations due to proportional gain being too low compared to integrator gain. | ||||
* | Remove broken ASpeed PWM fan and tach driver tie-in | Raptor Engineering Development Team | 2018-05-07 | 2 | -2/+0 |
| | | | | | | The current 4.10 kernel returns a bus error when attempting to read from the ASpeed fan controller tach. This causes a massive amount of systemd spam as the interface continues to attempt to rebind. Disable pending a fix in a newer kernel version. | ||||
* | Back off chassis fan proportional constantraptor-v1.0405-04-2018 | Raptor Engineering Development Team | 2018-05-04 | 1 | -1/+1 |
| | | | | | | | Ambient temperature swings should be slow enough, with a slow enough thermal response from the PCB, to make primary control via integrator viable. This slows down the fan responses and prevents audible "hunting" as the ambient sensor changes value more rapidly than the chassis fans actually need to react. | ||||
* | Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ↵ | Raptor Engineering Development Team | 2018-05-04 | 1 | -7/+7 |
| | | | | the new PID control algorithms | ||||
* | Revup phosphor-fan | Raptor Engineering Development Team | 2018-05-04 | 1 | -2/+2 |
| | |||||
* | Revup skeleton | Raptor Engineering Development Team | 2018-05-04 | 1 | -2/+2 |
| | |||||
* | Revup linuxraptor-v1.0304-30-2018 | Raptor Engineering Development Team | 2018-04-30 | 1 | -1/+1 |
| | |||||
* | Switch to PID control of main fans | Raptor Engineering Development Team | 2018-04-29 | 1 | -62/+65 |
| | |||||
* | Revup fan control and switch to branch | Raptor Engineering Development Team | 2018-04-29 | 1 | -2/+2 |
| | |||||
* | Wait 5 seconds for fans to reach full speed after fan controller init | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+1 |
| | |||||
* | Update fan monitor YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -1/+7 |
| | |||||
* | Update fan event YAML to new syntax | Raptor Engineering Development Team | 2018-04-28 | 1 | -193/+225 |
| | |||||
* | Revup fan control | Raptor Engineering Development Team | 2018-04-28 | 1 | -2/+2 |
| | |||||
* | Make decrease symmetric with increase | Raptor Engineering Development Team | 2018-04-28 | 2 | -12/+12 |
| | | | | Note that this verson oscillates badly, a more sophisticated control is needed |