Commit message (Expand) | Author | Age | Files | Lines | ||
---|---|---|---|---|---|---|
... | ||||||
* | Attempt to detect host power down if watchdog fails | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+18 | |
* | Tweak chassis fan PID controls again to mitigate integrator wind-up | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+2 | |
* | Force OCC disable script to have completed execution before host can power on | Raptor Engineering Development Team | 2019-04-25 | 2 | -0/+2 | |
* | Do not attempt to bind OCC drivers until IPL is complete | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+8 | |
* | Block chassis poweron and host start on completion of shutdown scripts | Raptor Engineering Development Team | 2019-04-25 | 2 | -0/+2 | |
* | Load final manufacturer ID and device ID data into IPMI data fields | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 | |
* | Add support for secondary PCIe region ambient temperature sensor on Talos II ... | Raptor Engineering Development Team | 2019-04-25 | 3 | -0/+26 | |
* | Add initial IPMI sensor mappings for Talos II | Raptor Engineering Development Team | 2019-04-25 | 6 | -0/+1865 | |
* | Add missing mutability attributes to IPMI inventory YAML | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+71 | |
* | Update IPMI YAML from Romulus source | Raptor Engineering Development Team | 2019-04-25 | 1 | -437/+499 | |
* | Bring boot VDN in line with values in datasheet | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 | |
* | Fix power sequencing on Talos II. | Brandon Bergren | 2019-04-25 | 2 | -0/+4 | |
* | Tweak chassis fan PID tuning | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+2 | |
* | Remove broken ASpeed PWM fan and tach driver tie-in | Raptor Engineering Development Team | 2019-04-25 | 2 | -2/+0 | |
* | Back off chassis fan proportional constant | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 | |
* | Lower chassis fan floor maps slightly to reduce unneccessary fan noise under ... | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+7 | |
* | Switch to PID control of main fans | Raptor Engineering Development Team | 2019-04-25 | 1 | -62/+65 | |
* | Wait 5 seconds for fans to reach full speed after fan controller init | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 | |
* | Update fan monitor YAML to new syntax | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+7 | |
* | Update fan event YAML to new syntax | Raptor Engineering Development Team | 2019-04-25 | 1 | -193/+225 | |
* | Make decrease symmetric with increase | Raptor Engineering Development Team | 2019-04-25 | 2 | -12/+12 | |
* | Don't set zone 2 to high speed when fewer than 4 chassis fans are installed, ... | Raptor Engineering Development Team | 2019-04-25 | 1 | -76/+0 | |
* | Tighten up fan response again | Raptor Engineering Development Team | 2019-04-25 | 2 | -15/+15 | |
* | Raise CPU core temp setpoints | Raptor Engineering Development Team | 2019-04-25 | 2 | -71/+71 | |
* | Revup phosphor-hwmon and switch to release 1.02 branch | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 | |
* | Enhance OCC communication failure error recovery | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+13 | |
* | Allow the on-board VGA device to be enabled or disabled based on FPGA jumper ... | Raptor Engineering Development Team | 2019-04-25 | 4 | -1/+60 | |
* | Work around upstream BMC bug 2946 | Raptor Engineering Development Team | 2019-04-25 | 2 | -2/+20 | |
* | Minimize chassis fan hunting with additional fan speed floor mappings in comm... | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+13 | |
* | Adjust floor threshold map to avoid chassis fan hunting at typical ambient te... | Raptor Engineering Development Team | 2019-04-25 | 1 | -7/+7 | |
* | Loosen ambient temperature fan controls somewhat | Raptor Engineering Development Team | 2019-04-25 | 1 | -3/+3 | |
* | Set chassis fan speeds based on on-board ambient temperature sensor | Raptor Engineering Development Team | 2019-04-25 | 1 | -60/+11 | |
* | Use hardbeep instead of softbeep on Talos systems | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 | |
* | Add obmc-hardbeep packaging files | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+9 | |
* | Split fan control zones for CPU0 and CPU1 | Raptor Engineering Development Team | 2019-04-25 | 3 | -22/+93 | |
* | Add softbeep packaging files | Raptor Engineering Development Team | 2019-04-25 | 2 | -1/+10 | |
* | Reset OCC on error detection | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+11 | |
* | Remove DD1 VCS workaround hack | Raptor Engineering Development Team | 2019-04-25 | 9 | -98/+2 | |
* | Recover from loss of either OCC | Raptor Engineering Development Team | 2019-04-25 | 1 | -3/+39 | |
* | Restart OCC service before restarting fan controller | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+17 | |
* | Fix incorrect Talos fan control settings | Raptor Engineering Development Team | 2019-04-25 | 3 | -21/+21 | |
* | Enable ambient temperature sensor | Raptor Engineering Development Team | 2019-04-25 | 2 | -0/+2 | |
* | Change IPL monitor LED service to simple service | Raptor Engineering Development Team | 2019-04-25 | 1 | -2/+1 | |
* | Add watchdog mode to OCC enable service | Raptor Engineering Development Team | 2019-04-25 | 2 | -5/+20 | |
* | Enable OCC service after IPL completion | Raptor Engineering Development Team | 2019-04-25 | 4 | -6/+16 | |
* | Enable the W83773G driver on Talos systems | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+1 | |
* | Enable Talos IPL monitor LED service | Raptor Engineering Development Team | 2019-04-25 | 1 | -1/+1 | |
* | Add IPL monitor LED service | Raptor Engineering Development Team | 2019-04-25 | 2 | -0/+38 | |
* | Add IPL status observer | Raptor Engineering Development Team | 2019-04-25 | 3 | -0/+39 | |
* | Signal BMC ready when BMC has finished booting on Talos systems | Raptor Engineering Development Team | 2019-04-25 | 1 | -0/+3 |