path: root/Documentation/sound/alsa/soc/DAI.txt

ASoC currently supports the three main Digital Audio Interfaces (DAI) found on
SoC controllers and portable audio CODECS today, namely AC97, I2S and PCM.


AC97
====

  AC97 is a five wire interface commonly found on many PC sound cards. It is
now also popular in many portable devices. This DAI has a reset line and time
multiplexes its data on its SDATA_OUT (playback) and SDATA_IN (capture) lines.
The bit clock (BCLK) is always driven by the CODEC (usually 12.288MHz) and the
frame (FRAME) (usually 48kHz) is always driven by the controller. Each AC97
frame is 21uS long and is divided into 13 time slots.

The AC97 specification can be found at :-
http://www.intel.com/design/chipsets/audio/ac97_r23.pdf


I2S
===

 I2S is a common 4 wire DAI used in HiFi, STB and portable devices. The Tx and
Rx lines are used for audio transmision, whilst the bit clock (BCLK) and
left/right clock (LRC) synchronise the link. I2S is flexible in that either the
controller or CODEC can drive (master) the BCLK and LRC clock lines. Bit clock
usually varies depending on the sample rate and the master system clock
(SYSCLK). LRCLK is the same as the sample rate. A few devices support separate
ADC and DAC LRCLK's, this allows for similtanious capture and playback at
different sample rates.

I2S has several different operating modes:-

 o I2S - MSB is transmitted on the falling edge of the first BCLK after LRC
         transition.

 o Left Justified - MSB is transmitted on transition of LRC.

 o Right Justified - MSB is transmitted sample size BCLK's before LRC
                     transition.

PCM
===

PCM is another 4 wire interface, very similar to I2S, that can support a more
flexible protocol. It has bit clock (BCLK) and sync (SYNC) lines that are used
to synchronise the link whilst the Tx and Rx lines are used to transmit and
receive the audio data. Bit clock usually varies depending on sample rate
whilst sync runs at the sample rate. PCM also supports Time Division
Multiplexing (TDM) in that several devices can use the bus similtaniuosly (This
is sometimes referred to as network mode).

Common PCM operating modes:-

 o Mode A - MSB is transmitted on falling edge of first BCLK after FRAME/SYNC.

 o Mode B - MSB is transmitted on rising edge of FRAME/SYNC.


ASoC DAI Configuration
======================

Every CODEC DAI and SoC DAI must have their capabilities defined in order to
be configured together at runtime when the audio and clocking parameters are
known. This is achieved by creating an array of struct snd_soc_hw_mode in the
the CODEC and SoC interface drivers. Each element in the array describes a DAI
mode and each mode is usually based upon the DAI system clock to sample rate
ratio (FS).

i.e. 48k sample rate @ 256 FS = sytem clock of 12.288 MHz
     48000 * 256 = 12288000

The CPU and Codec DAI modes are then ANDed together at runtime to determine the
rutime DAI configuration for both the Codec and CPU.

When creating a new codec or SoC DAI it's probably best to start of with a few
sample rates first and then test your interface.

struct snd_soc_dai_mode is defined (in soc.h) as:-

/* SoC DAI mode */
struct snd_soc_dai_mode {
	u16 fmt;		/* SND_SOC_DAIFMT_* */
	u16 tdm;		/* SND_SOC_HWTDM_* */
	u64 pcmfmt; 	/* SNDRV_PCM_FMTBIT_* */
	u16 pcmrate;	/* SND_SOC_HWRATE_* */
	u16 pcmdir:2;	/* SND_SOC_HWDIR_* */
	u16 flags:8;	/* hw flags */
	u16 fs;			/* mclk to rate divider */
	u64 bfs;		/* mclk to bclk dividers */
	unsigned long priv;		/* private mode data */
};

fmt:
----
This field defines the DAI mode hardware format (e.g. I2S settings) and
supports the following settings:-

 1) hardware DAI formats

#define SND_SOC_DAIFMT_I2S        (1 << 0)	/* I2S mode */
#define SND_SOC_DAIFMT_RIGHT_J    (1 << 1)	/* Right justified mode */
#define SND_SOC_DAIFMT_LEFT_J     (1 << 2)	/* Left Justified mode */
#define SND_SOC_DAIFMT_DSP_A      (1 << 3)	/* L data msb after FRM */
#define SND_SOC_DAIFMT_DSP_B      (1 << 4)	/* L data msb during FRM */
#define SND_SOC_DAIFMT_AC97       (1 << 5)	/* AC97 */

 2) hw DAI signal inversions

#define SND_SOC_DAIFMT_NB_NF		(1 << 8)	/* normal bit clock + frame */
#define SND_SOC_DAIFMT_NB_IF		(1 << 9)	/* normal bclk + inv frm */
#define SND_SOC_DAIFMT_IB_NF		(1 << 10)	/* invert bclk + nor frm */
#define SND_SOC_DAIFMT_IB_IF		(1 << 11)	/* invert bclk + frm */

 3) hw clock masters
    This is wrt the codec, the inverse is true for the interface
    i.e. if the codec is clk and frm master then the interface is
    clk and frame slave.

#define SND_SOC_DAIFMT_CBM_CFM		(1 << 12)	/* codec clk & frm master */
#define SND_SOC_DAIFMT_CBS_CFM		(1 << 13)	/* codec clk slave & frm master */
#define SND_SOC_DAIFMT_CBM_CFS		(1 << 14)	/* codec clk master & frame slave */
#define SND_SOC_DAIFMT_CBS_CFS		(1 << 15)	/* codec clk & frm slave */

At least one option from each section must be selected. Multiple selections are
also supported e.g.

 .fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_RIGHT_J | \
	SND_SOC_DAIFMT_NB_NF | SND_SOC_DAIFMT_NB_IF | SND_SOC_DAIFMT_IB_NF | \
	SND_SOC_DAIFMT_IB_IF


tdm:
------
This field defines the Time Division Multiplexing left and right word
positions for the DAI mode if applicable. Set to SND_SOC_DAITDM_LRDW(0,0) for
no TDM.


pcmfmt:
---------
The hardware PCM format. This describes the PCM formats supported by the DAI
mode e.g.

 .pcmfmt = SNDRV_PCM_FORMAT_S16_LE | SNDRV_PCM_FORMAT_S20_3LE | \
 	SNDRV_PCM_FORMAT_S24_3LE

pcmrate:
----------
The PCM sample rates supported by the DAI mode. e.g.

 .pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_11025 | SNDRV_PCM_RATE_16000 | \
	SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
	SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000


pcmdir:
---------
The stream directions supported by this mode. e.g. playback and capture


flags:
--------
The DAI hardware flags supported by the mode.

/* use bfs mclk divider mode (BCLK = MCLK / x) */
#define SND_SOC_DAI_BFS_DIV		0x1
/* use bfs rate mulitplier  (BCLK = RATE * x)*/
#define SND_SOC_DAI_BFS_RATE	0x2
/* use bfs rcw multiplier (BCLK = RATE * CHN * WORD SIZE) */
#define SND_SOC_DAI_BFS_RCW		0x4
/* capture and playback can use different clocks */
#define SND_SOC_DAI_ASYNC		0x8

NOTE: Bitclock division and mulitiplication modes can be safely matched by the
core logic.


fs:
-----
The FS supported by this DAI mode FS is the ratio between the system clock and
the sample rate. See above

bfs:
------
BFS is the ratio of BCLK to MCLK or the ratio of BCLK to sample rate (this
depends on the codec or CPU DAI).

The BFS supported by the DAI mode. This can either be the ratio between the
bitclock (BCLK) and the sample rate OR the ratio between the system clock and
the sample rate. Depends on the flags above.

priv:
-----
private codec mode data.



Examples
========

Note that Codec DAI and CPU DAI examples are interchangeable in these examples
as long as the bus master is reversed. i.e.

  SND_SOC_DAIFMT_CBM_CFM would become SND_SOC_DAIFMT_CBS_CFS
  and vice versa.

This applies to all SND_SOC_DAIFMT_CB*_CF*.

Example 1
---------

Simple codec that only runs at 8k & 48k @ 256FS in master mode, can generate a
BCLK of either MCLK/2 or MCLK/4.

	/* codec master */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = SND_SOC_FSBD(2) | SND_SOC_FSBD(4),
	}


Example 2
---------
Simple codec that only runs at 8k & 48k @ 256FS in master mode, can generate a
BCLK of either Rate * 32 or Rate * 64.

	/* codec master */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_RATE,
		.fs = 256,
		.bfs = 32,
	},
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_RATE,
		.fs = 256,
		.bfs = 64,
	},


Example 3
---------
Codec that runs at 8k & 48k @ 256FS in master mode, can generate a BCLK that
is a multiple of Rate * channels * word size. (RCW) i.e.

	BCLK = 8000 * 2 * 16 (8k, stereo, 16bit)
	     = 256kHz

This codecs supports a RCW multiple of 1,2

	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_RCW,
		.fs = 256,
		.bfs = SND_SOC_FSBW(1) | SND_SOC_FSBW(2),
	}


Example 4
---------
Codec that only runs at 8k & 48k @ 256FS in master mode, can generate a
BCLK of either Rate * 32 or Rate * 64. Codec can also run in slave mode as long
as BCLK is rate * 32 or rate * 64.

	/* codec master */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_RATE,
		.fs = 256,
		.bfs = 32,
	},
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_RATE,
		.fs = 256,
		.bfs = 64,
	},

	/* codec slave */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmdir = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_RATE,
		.fs = SND_SOC_FS_ALL,
		.bfs = 32,
	},
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmdir = SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_RATE,
		.fs = SND_SOC_FS_ALL,
		.bfs = 64,
	},


Example 5
---------
Codec that only runs at 8k, 16k, 32k, 48k, 96k @ 128FS, 192FS & 256FS in master
mode and can generate a BCLK of MCLK / (1,2,4,8,16). Codec can also run in slave
mode as and does not care about FS or BCLK (as long as there is enough bandwidth).

	#define CODEC_FSB \
	(SND_SOC_FSBD(1) | SND_SOC_FSBD(2) | SND_SOC_FSBD(4) | \
	SND_SOC_FSBD(8) | SND_SOC_FSBD(16))

	#define CODEC_RATES \
	(SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 | SNDRV_PCM_RATE_32000 |\
	 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_96000)

	/* codec master @ 128, 192 & 256 FS */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = CODEC_RATES,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 128,
		.bfs = CODEC_FSB,
	},

	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = CODEC_RATES,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 192,
		.bfs = CODEC_FSB
	},

	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = CODEC_RATES,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = CODEC_FSB,
	},

	/* codec slave */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = CODEC_RATES,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.fs = SND_SOC_FS_ALL,
		.bfs = SND_SOC_FSB_ALL,
	},


Example 6
---------
Codec that only runs at 8k, 44.1k, 48k @ different FS in master mode (for use
with a fixed MCLK) and can generate a BCLK of MCLK / (1,2,4,8,16).
Codec can also run in slave mode as and does not care about FS or BCLK (as long
as there is enough bandwidth). Codec can support 16, 24 and 32 bit PCM sample
sizes.

	#define CODEC_FSB \
	(SND_SOC_FSBD(1) | SND_SOC_FSBD(2) | SND_SOC_FSBD(4) | \
	SND_SOC_FSBD(8) | SND_SOC_FSBD(16))

	#define CODEC_PCM_FORMATS \
	(SNDRV_PCM_FORMAT_S16_LE | SNDRV_PCM_FORMAT_S20_3LE | \
	SNDRV_PCM_FORMAT_S24_3LE | SNDRV_PCM_FORMAT_S24_LE | SNDRV_PCM_FORMAT_S32_LE)

	/* codec master */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 1536,
		.bfs = CODEC_FSB,
	},

	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_44100,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 272,
		.bfs = CODEC_FSB,
	},

	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_48000,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = CODEC_FSB,
	},

	/* codec slave */
	{
		.fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FORMAT_S16_LE,
		.pcmrate = CODEC_RATES,
		.pcmdir = SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE,
		.fs = SND_SOC_FS_ALL,
		.bfs = SND_SOC_FSB_ALL,
	},


Example 7
---------
AC97 Codec that does not support VRA (i.e only runs at 48k).

	#define AC97_DIR \
	(SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE)

	#define AC97_PCM_FORMATS \
	(SNDRV_PCM_FORMAT_S16_LE | SNDRV_PCM_FORMAT_S18_3LE | \
	SNDRV_PCM_FORMAT_S20_3LE)

	/* AC97 with no VRA */
	{
		.pcmfmt = AC97_PCM_FORMATS,
		.pcmrate = SNDRV_PCM_RATE_48000,
	}


Example 8
---------

CPU DAI that supports 8k - 48k @ 256FS and BCLK = MCLK / 4 in master mode.
Slave mode (CPU DAI is FRAME master) supports 8k - 96k at any FS as long as
BCLK = 64 * rate. (Intel XScale I2S controller).

	#define PXA_I2S_DAIFMT \
	(SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_NB_NF)

	#define PXA_I2S_DIR \
	(SND_SOC_DAIDIR_PLAYBACK | SND_SOC_DAIDIR_CAPTURE)

	#define PXA_I2S_RATES \
	(SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_11025 | SNDRV_PCM_RATE_16000 | \
	SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
	SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000)

	/* priv is divider */
	static struct snd_soc_dai_mode pxa2xx_i2s_modes[] = {
	/* pxa2xx I2S frame and clock master modes */
	{
		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_8000,
		.pcmdir = PXA_I2S_DIR,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = SND_SOC_FSBD(4),
		.priv = 0x48,
	},
	{
		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_11025,
		.pcmdir = PXA_I2S_DIR,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = SND_SOC_FSBD(4),
		.priv = 0x34,
	},
	{
		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_16000,
		.pcmdir = PXA_I2S_DIR,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = SND_SOC_FSBD(4),
		.priv = 0x24,
	},
	{
		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_22050,
		.pcmdir = PXA_I2S_DIR,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = SND_SOC_FSBD(4),
		.priv = 0x1a,
	},
	{
		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_44100,
		.pcmdir = PXA_I2S_DIR,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = SND_SOC_FSBD(4),
		.priv = 0xd,
	},
	{
		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBS_CFS,
		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
		.pcmrate = SNDRV_PCM_RATE_48000,
		.pcmdir = PXA_I2S_DIR,
		.flags = SND_SOC_DAI_BFS_DIV,
		.fs = 256,
		.bfs = SND_SOC_FSBD(4),
		.priv = 0xc,
	},

	/* pxa2xx I2S frame master and clock slave mode */
	{
		.fmt = PXA_I2S_DAIFMT | SND_SOC_DAIFMT_CBM_CFS,
		.pcmfmt = SNDRV_PCM_FMTBIT_S16_LE,
		.pcmrate = PXA_I2S_RATES,
		.pcmdir = PXA_I2S_DIR,
		.fs = SND_SOC_FS_ALL,
		.flags = SND_SOC_DAI_BFS_RATE,
		.bfs = 64,
		.priv = 0x48,
	},
};