From 241b652f1995de138106afd2f2e4eda9f8a3c240 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Fri, 5 Nov 2010 09:59:01 -0400 Subject: xhci: Remove excessive printks with shared IRQs. If the xHCI host controller shares an interrupt line with another device, the xHCI driver needs to check if the interrupt was generated by its hardware. Unfortunately, the user will see a ton of "Spurious interrupt." lines if the other hardware interrupts often. Lawrence found his dmesg output cluttered with this output when the xHCI host shared an interrupt with his i915 hardware. Remove the warning, as sharing an interrupt is a normal thing. This should be applied to the 2.6.36 stable tree. Signed-off-by: Sarah Sharp Reported-by: Lawrence Rust Cc: stable@kernel.org --- drivers/usb/host/xhci-ring.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 9f3115e729b1..df558f6f84e3 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2104,7 +2104,6 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) if (!(status & STS_EINT)) { spin_unlock(&xhci->lock); - xhci_warn(xhci, "Spurious interrupt.\n"); return IRQ_NONE; } xhci_dbg(xhci, "op reg status = %08x\n", status); -- cgit v1.2.1 From 74bb844af8ec6a4c360b1fc7feb139801c0cacfd Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Wed, 27 Oct 2010 16:44:52 +0800 Subject: xHCI: release spinlock when setup interrupt Jiri Slaby reports spinlock is held while calling kmalloc(GFP_KERNEL) and request_irq() in xhci_resume(). Release the spinlock when setup interrupt. Reported-by: Jiri Slaby Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 5d7d4e951ea4..7c8d70fbe113 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -714,6 +714,7 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) return retval; } + spin_unlock_irq(&xhci->lock); /* Re-setup MSI-X */ if (hcd->irq) free_irq(hcd->irq, hcd); @@ -736,6 +737,7 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) hcd->irq = pdev->irq; } + spin_lock_irq(&xhci->lock); /* step 4: set Run/Stop bit */ command = xhci_readl(xhci, &xhci->op_regs->command); command |= CMD_RUN; -- cgit v1.2.1 From dc07c91b9b4067022210e68d914a6890a4d70622 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Thu, 11 Nov 2010 17:43:57 +0800 Subject: xHCI: fix wMaxPacketSize mask USB2.0 spec 9.6.6 says: For all endpoints, bit 10..0 specify the maximum packet size(in bytes). So the wMaxPacketSize mask should be 0x7ff rather than 0x3ff. This patch should be queued for the stable tree. The bug in xhci_endpoint_init() was present as far back as 2.6.31, and the bug in xhci_get_max_esit_payload() was present when the function was introduced in 2.6.34. Reported-by: Sander Eikelenboom Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci-mem.c | 4 ++-- drivers/usb/host/xhci.h | 5 +++++ 2 files changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 202770676da3..d178761c3981 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1045,7 +1045,7 @@ static inline u32 xhci_get_max_esit_payload(struct xhci_hcd *xhci, if (udev->speed == USB_SPEED_SUPER) return ep->ss_ep_comp.wBytesPerInterval; - max_packet = ep->desc.wMaxPacketSize & 0x3ff; + max_packet = GET_MAX_PACKET(ep->desc.wMaxPacketSize); max_burst = (ep->desc.wMaxPacketSize & 0x1800) >> 11; /* A 0 in max burst means 1 transfer per ESIT */ return max_packet * (max_burst + 1); @@ -1135,7 +1135,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, /* Fall through */ case USB_SPEED_FULL: case USB_SPEED_LOW: - max_packet = ep->desc.wMaxPacketSize & 0x3ff; + max_packet = GET_MAX_PACKET(ep->desc.wMaxPacketSize); ep_ctx->ep_info2 |= MAX_PACKET(max_packet); break; default: diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 93d3bf4d213c..85e65647d445 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -621,6 +621,11 @@ struct xhci_ep_ctx { #define MAX_PACKET_MASK (0xffff << 16) #define MAX_PACKET_DECODED(p) (((p) >> 16) & 0xffff) +/* Get max packet size from ep desc. Bit 10..0 specify the max packet size. + * USB2.0 spec 9.6.6. + */ +#define GET_MAX_PACKET(p) ((p) & 0x7ff) + /* tx_info bitmasks */ #define AVG_TRB_LENGTH_FOR_EP(p) ((p) & 0xffff) #define MAX_ESIT_PAYLOAD_FOR_EP(p) (((p) & 0xffff) << 16) -- cgit v1.2.1 From 898213200cbadc570ef4248a6d90430c4a9c2908 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Fri, 12 Nov 2010 11:59:31 -0800 Subject: xhci: Fix command ring replay after resume. Andiry's xHCI bus suspend patch introduced the possibly of a host controller replaying old commands on the command ring, if the host successfully restores the registers after a resume. After a resume from suspend, the xHCI driver must restore the registers, including the command ring pointer. I had suggested that Andiry set the command ring pointer to the current command ring dequeue pointer, so that the driver wouldn't have to zero the command ring. Unfortunately, setting the command ring pointer to the current dequeue pointer won't work because the register assumes the pointer is 64-byte aligned, and TRBs on the command ring are 16-byte aligned. The lower seven bits will always be masked off, leading to the written pointer being up to 3 TRBs behind the intended pointer. Here's a log excerpt. On init, the xHCI driver places a vendor-specific command on the command ring: [ 215.750958] xhci_hcd 0000:01:00.0: Vendor specific event TRB type = 48 [ 215.750960] xhci_hcd 0000:01:00.0: NEC firmware version 30.25 [ 215.750962] xhci_hcd 0000:01:00.0: Command ring deq = 0x3781e010 (DMA) When we resume, the command ring dequeue pointer to be written should have been 0x3781e010. Instead, it's 0x3781e000: [ 235.557846] xhci_hcd 0000:01:00.0: // Setting command ring address to 0x3781e001 [ 235.557848] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 64'hffffc900100bc038, 64'h3781e001, 4'hf); [ 235.557850] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc900100bc020, 32'h204, 4'hf); [ 235.557866] usb usb9: root hub lost power or was reset (I can't see the results of this bug because the xHCI restore always fails on this box, and the xHCI driver re-allocates everything.) The fix is to zero the command ring and put the software and hardware enqueue and dequeue pointer back to the beginning of the ring. We do this before the system suspends, to be paranoid and prevent the BIOS from starting the host without clearing the command ring pointer, which might cause the host to muck with stale memory. (The pointer isn't required to be in the suspend power well, but it could be.) The command ring pointer is set again after the host resumes. Signed-off-by: Sarah Sharp Tested-by: Andiry Xu --- drivers/usb/host/xhci.c | 71 ++++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 61 insertions(+), 10 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 7c8d70fbe113..06fca0835b52 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -577,6 +577,65 @@ static void xhci_restore_registers(struct xhci_hcd *xhci) xhci_write_64(xhci, xhci->s3.erst_base, &xhci->ir_set->erst_base); } +static void xhci_set_cmd_ring_deq(struct xhci_hcd *xhci) +{ + u64 val_64; + + /* step 2: initialize command ring buffer */ + val_64 = xhci_read_64(xhci, &xhci->op_regs->cmd_ring); + val_64 = (val_64 & (u64) CMD_RING_RSVD_BITS) | + (xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg, + xhci->cmd_ring->dequeue) & + (u64) ~CMD_RING_RSVD_BITS) | + xhci->cmd_ring->cycle_state; + xhci_dbg(xhci, "// Setting command ring address to 0x%llx\n", + (long unsigned long) val_64); + xhci_write_64(xhci, val_64, &xhci->op_regs->cmd_ring); +} + +/* + * The whole command ring must be cleared to zero when we suspend the host. + * + * The host doesn't save the command ring pointer in the suspend well, so we + * need to re-program it on resume. Unfortunately, the pointer must be 64-byte + * aligned, because of the reserved bits in the command ring dequeue pointer + * register. Therefore, we can't just set the dequeue pointer back in the + * middle of the ring (TRBs are 16-byte aligned). + */ +static void xhci_clear_command_ring(struct xhci_hcd *xhci) +{ + struct xhci_ring *ring; + struct xhci_segment *seg; + + ring = xhci->cmd_ring; + seg = ring->deq_seg; + do { + memset(seg->trbs, 0, SEGMENT_SIZE); + seg = seg->next; + } while (seg != ring->deq_seg); + + /* Reset the software enqueue and dequeue pointers */ + ring->deq_seg = ring->first_seg; + ring->dequeue = ring->first_seg->trbs; + ring->enq_seg = ring->deq_seg; + ring->enqueue = ring->dequeue; + + /* + * Ring is now zeroed, so the HW should look for change of ownership + * when the cycle bit is set to 1. + */ + ring->cycle_state = 1; + + /* + * Reset the hardware dequeue pointer. + * Yes, this will need to be re-written after resume, but we're paranoid + * and want to make sure the hardware doesn't access bogus memory + * because, say, the BIOS or an SMI started the host without changing + * the command ring pointers. + */ + xhci_set_cmd_ring_deq(xhci); +} + /* * Stop HC (not bus-specific) * @@ -604,6 +663,7 @@ int xhci_suspend(struct xhci_hcd *xhci) spin_unlock_irq(&xhci->lock); return -ETIMEDOUT; } + xhci_clear_command_ring(xhci); /* step 3: save registers */ xhci_save_registers(xhci); @@ -635,7 +695,6 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) u32 command, temp = 0; struct usb_hcd *hcd = xhci_to_hcd(xhci); struct pci_dev *pdev = to_pci_dev(hcd->self.controller); - u64 val_64; int old_state, retval; old_state = hcd->state; @@ -648,15 +707,7 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) /* step 1: restore register */ xhci_restore_registers(xhci); /* step 2: initialize command ring buffer */ - val_64 = xhci_read_64(xhci, &xhci->op_regs->cmd_ring); - val_64 = (val_64 & (u64) CMD_RING_RSVD_BITS) | - (xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg, - xhci->cmd_ring->dequeue) & - (u64) ~CMD_RING_RSVD_BITS) | - xhci->cmd_ring->cycle_state; - xhci_dbg(xhci, "// Setting command ring address to 0x%llx\n", - (long unsigned long) val_64); - xhci_write_64(xhci, val_64, &xhci->op_regs->cmd_ring); + xhci_set_cmd_ring_deq(xhci); /* step 3: restore state and start state*/ /* step 3: set CRS flag */ command = xhci_readl(xhci, &xhci->op_regs->command); -- cgit v1.2.1 From e502ac5e1eca99d7dc3f12b2a6780ccbca674858 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:11:45 -0800 Subject: USB: atm: ueagle-atm: fix up some permissions on the sysfs files Some of the sysfs files had the incorrect permissions. Some didn't make sense at all (writable for a file that you could not write to?) Reported-by: Linus Torvalds Cc: Matthieu Castet Cc: Stanislaw Gruszka Cc: Damien Bergamini Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/atm/ueagle-atm.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/atm/ueagle-atm.c b/drivers/usb/atm/ueagle-atm.c index ea071a5b6eee..44447f54942f 100644 --- a/drivers/usb/atm/ueagle-atm.c +++ b/drivers/usb/atm/ueagle-atm.c @@ -2301,7 +2301,7 @@ out: return ret; } -static DEVICE_ATTR(stat_status, S_IWUGO | S_IRUGO, read_status, reboot); +static DEVICE_ATTR(stat_status, S_IWUSR | S_IRUGO, read_status, reboot); static ssize_t read_human_status(struct device *dev, struct device_attribute *attr, char *buf) @@ -2364,8 +2364,7 @@ out: return ret; } -static DEVICE_ATTR(stat_human_status, S_IWUGO | S_IRUGO, - read_human_status, NULL); +static DEVICE_ATTR(stat_human_status, S_IRUGO, read_human_status, NULL); static ssize_t read_delin(struct device *dev, struct device_attribute *attr, char *buf) @@ -2397,7 +2396,7 @@ out: return ret; } -static DEVICE_ATTR(stat_delin, S_IWUGO | S_IRUGO, read_delin, NULL); +static DEVICE_ATTR(stat_delin, S_IRUGO, read_delin, NULL); #define UEA_ATTR(name, reset) \ \ -- cgit v1.2.1 From 723b991a62d94f74c9f19abd3da6e937288eb969 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:15:11 -0800 Subject: USB: ehci: fix debugfs 'lpm' permissions The permissions for the lpm debugfs file is incorrect, this fixes it. Reported-by: Linus Torvalds Cc: Alek Du Cc: Jacob Pan Cc: David Brownell Cc: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-dbg.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/ehci-dbg.c b/drivers/usb/host/ehci-dbg.c index 86afdc73322f..6e2599661b5b 100644 --- a/drivers/usb/host/ehci-dbg.c +++ b/drivers/usb/host/ehci-dbg.c @@ -1067,7 +1067,7 @@ static inline void create_debug_files (struct ehci_hcd *ehci) &debug_registers_fops)) goto file_error; - if (!debugfs_create_file("lpm", S_IRUGO|S_IWUGO, ehci->debug_dir, bus, + if (!debugfs_create_file("lpm", S_IRUGO|S_IWUSR, ehci->debug_dir, bus, &debug_lpm_fops)) goto file_error; -- cgit v1.2.1 From d9624e75f6ad94d8a0718c1fafa89186d271a78c Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:17:52 -0800 Subject: USB: storage: sierra_ms: fix sysfs file attribute A non-writable sysfs file shouldn't have writable attributes. Reported-by: Linus Torvalds Cc: Kevin Lloyd Cc: Matthew Dharm Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/sierra_ms.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/storage/sierra_ms.c b/drivers/usb/storage/sierra_ms.c index 57fc2f532cab..ceba512f84d0 100644 --- a/drivers/usb/storage/sierra_ms.c +++ b/drivers/usb/storage/sierra_ms.c @@ -121,7 +121,7 @@ static ssize_t show_truinst(struct device *dev, struct device_attribute *attr, } return result; } -static DEVICE_ATTR(truinst, S_IWUGO | S_IRUGO, show_truinst, NULL); +static DEVICE_ATTR(truinst, S_IRUGO, show_truinst, NULL); int sierra_ms_init(struct us_data *us) { -- cgit v1.2.1 From c990600d340641150f7270470a64bd99a5c0b225 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:32:38 -0800 Subject: USB: misc: cypress_cy7c63: fix up some sysfs attribute permissions They should not be writable by any user. Reported-by: Linus Torvalds Cc: Oliver Bock Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/cypress_cy7c63.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/misc/cypress_cy7c63.c b/drivers/usb/misc/cypress_cy7c63.c index 2f43c57743c9..9251773ecef4 100644 --- a/drivers/usb/misc/cypress_cy7c63.c +++ b/drivers/usb/misc/cypress_cy7c63.c @@ -196,11 +196,9 @@ static ssize_t get_port1_handler(struct device *dev, return read_port(dev, attr, buf, 1, CYPRESS_READ_PORT_ID1); } -static DEVICE_ATTR(port0, S_IWUGO | S_IRUGO, - get_port0_handler, set_port0_handler); +static DEVICE_ATTR(port0, S_IRUGO | S_IWUSR, get_port0_handler, set_port0_handler); -static DEVICE_ATTR(port1, S_IWUGO | S_IRUGO, - get_port1_handler, set_port1_handler); +static DEVICE_ATTR(port1, S_IRUGO | S_IWUSR, get_port1_handler, set_port1_handler); static int cypress_probe(struct usb_interface *interface, -- cgit v1.2.1 From d489a4b3926bad571d404ca6508f6744b9602776 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:34:26 -0800 Subject: USB: misc: trancevibrator: fix up a sysfs attribute permission It should not be writable by any user. Reported-by: Linus Torvalds Cc: Sam Hocevar Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/trancevibrator.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/misc/trancevibrator.c b/drivers/usb/misc/trancevibrator.c index d77aba46ae85..f63776a48e2a 100644 --- a/drivers/usb/misc/trancevibrator.c +++ b/drivers/usb/misc/trancevibrator.c @@ -86,7 +86,7 @@ static ssize_t set_speed(struct device *dev, struct device_attribute *attr, return count; } -static DEVICE_ATTR(speed, S_IWUGO | S_IRUGO, show_speed, set_speed); +static DEVICE_ATTR(speed, S_IRUGO | S_IWUSR, show_speed, set_speed); static int tv_probe(struct usb_interface *interface, const struct usb_device_id *id) -- cgit v1.2.1 From 48f115470e68d443436b76b22dad63ffbffd6b97 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:35:49 -0800 Subject: USB: misc: usbled: fix up some sysfs attribute permissions They should not be writable by any user. Reported-by: Linus Torvalds Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/usbled.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/misc/usbled.c b/drivers/usb/misc/usbled.c index 63da2c3c838f..c96f51de1696 100644 --- a/drivers/usb/misc/usbled.c +++ b/drivers/usb/misc/usbled.c @@ -94,7 +94,7 @@ static ssize_t set_##value(struct device *dev, struct device_attribute *attr, co change_color(led); \ return count; \ } \ -static DEVICE_ATTR(value, S_IWUGO | S_IRUGO, show_##value, set_##value); +static DEVICE_ATTR(value, S_IRUGO | S_IWUSR, show_##value, set_##value); show_set(blue); show_set(red); show_set(green); -- cgit v1.2.1 From e24d7ace4e822debcb78386bf279c9aba4d7fbd1 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:36:44 -0800 Subject: USB: misc: usbsevseg: fix up some sysfs attribute permissions They should not be writable by any user. Reported-by: Linus Torvalds Cc: Harrison Metzger Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/usbsevseg.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/misc/usbsevseg.c b/drivers/usb/misc/usbsevseg.c index de8ef945b536..417b8f207e8b 100644 --- a/drivers/usb/misc/usbsevseg.c +++ b/drivers/usb/misc/usbsevseg.c @@ -192,7 +192,7 @@ static ssize_t set_attr_##name(struct device *dev, \ \ return count; \ } \ -static DEVICE_ATTR(name, S_IWUGO | S_IRUGO, show_attr_##name, set_attr_##name); +static DEVICE_ATTR(name, S_IRUGO | S_IWUSR, show_attr_##name, set_attr_##name); static ssize_t show_attr_text(struct device *dev, struct device_attribute *attr, char *buf) @@ -223,7 +223,7 @@ static ssize_t set_attr_text(struct device *dev, return count; } -static DEVICE_ATTR(text, S_IWUGO | S_IRUGO, show_attr_text, set_attr_text); +static DEVICE_ATTR(text, S_IRUGO | S_IWUSR, show_attr_text, set_attr_text); static ssize_t show_attr_decimals(struct device *dev, struct device_attribute *attr, char *buf) @@ -272,8 +272,7 @@ static ssize_t set_attr_decimals(struct device *dev, return count; } -static DEVICE_ATTR(decimals, S_IWUGO | S_IRUGO, - show_attr_decimals, set_attr_decimals); +static DEVICE_ATTR(decimals, S_IRUGO | S_IWUSR, show_attr_decimals, set_attr_decimals); static ssize_t show_attr_textmode(struct device *dev, struct device_attribute *attr, char *buf) @@ -319,8 +318,7 @@ static ssize_t set_attr_textmode(struct device *dev, return -EINVAL; } -static DEVICE_ATTR(textmode, S_IWUGO | S_IRUGO, - show_attr_textmode, set_attr_textmode); +static DEVICE_ATTR(textmode, S_IRUGO | S_IWUSR, show_attr_textmode, set_attr_textmode); MYDEV_ATTR_SIMPLE_UNSIGNED(powered, update_display_powered); -- cgit v1.2.1 From 3d965875144b905d71dfb4d291c665c0794222c4 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 15 Nov 2010 11:37:55 -0800 Subject: USB: OTG: langwell_otg: fix up some sysfs attribute permissions They should not be writable by any user. Reported-by: Linus Torvalds Cc: Hao Wu Cc: Alan Cox Cc: Alek Du Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/otg/langwell_otg.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/otg/langwell_otg.c b/drivers/usb/otg/langwell_otg.c index bdc3ea66be69..9fea48264fa2 100644 --- a/drivers/usb/otg/langwell_otg.c +++ b/drivers/usb/otg/langwell_otg.c @@ -1896,7 +1896,7 @@ set_a_bus_req(struct device *dev, struct device_attribute *attr, } return count; } -static DEVICE_ATTR(a_bus_req, S_IRUGO | S_IWUGO, get_a_bus_req, set_a_bus_req); +static DEVICE_ATTR(a_bus_req, S_IRUGO | S_IWUSR, get_a_bus_req, set_a_bus_req); static ssize_t get_a_bus_drop(struct device *dev, struct device_attribute *attr, char *buf) @@ -1942,8 +1942,7 @@ set_a_bus_drop(struct device *dev, struct device_attribute *attr, } return count; } -static DEVICE_ATTR(a_bus_drop, S_IRUGO | S_IWUGO, - get_a_bus_drop, set_a_bus_drop); +static DEVICE_ATTR(a_bus_drop, S_IRUGO | S_IWUSR, get_a_bus_drop, set_a_bus_drop); static ssize_t get_b_bus_req(struct device *dev, struct device_attribute *attr, char *buf) @@ -1988,7 +1987,7 @@ set_b_bus_req(struct device *dev, struct device_attribute *attr, } return count; } -static DEVICE_ATTR(b_bus_req, S_IRUGO | S_IWUGO, get_b_bus_req, set_b_bus_req); +static DEVICE_ATTR(b_bus_req, S_IRUGO | S_IWUSR, get_b_bus_req, set_b_bus_req); static ssize_t set_a_clr_err(struct device *dev, struct device_attribute *attr, @@ -2012,7 +2011,7 @@ set_a_clr_err(struct device *dev, struct device_attribute *attr, } return count; } -static DEVICE_ATTR(a_clr_err, S_IWUGO, NULL, set_a_clr_err); +static DEVICE_ATTR(a_clr_err, S_IWUSR, NULL, set_a_clr_err); static struct attribute *inputs_attrs[] = { &dev_attr_a_bus_req.attr, -- cgit v1.2.1 From f281233d3eba15fb225d21ae2e228fd4553d824a Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Tue, 16 Nov 2010 02:10:29 -0500 Subject: SCSI host lock push-down Move the mid-layer's ->queuecommand() invocation from being locked with the host lock to being unlocked to facilitate speeding up the critical path for drivers who don't need this lock taken anyway. The patch below presents a simple SCSI host lock push-down as an equivalent transformation. No locking or other behavior should change with this patch. All existing bugs and locking orders are preserved. Additionally, add one parameter to queuecommand, struct Scsi_Host * and remove one parameter from queuecommand, void (*done)(struct scsi_cmnd *) Scsi_Host* is a convenient pointer that most host drivers need anyway, and 'done' is redundant to struct scsi_cmnd->scsi_done. Minimal code disturbance was attempted with this change. Most drivers needed only two one-line modifications for their host lock push-down. Signed-off-by: Jeff Garzik Acked-by: James Bottomley Signed-off-by: Linus Torvalds --- drivers/usb/image/microtek.c | 6 ++++-- drivers/usb/storage/scsiglue.c | 4 +++- drivers/usb/storage/uas.c | 4 +++- 3 files changed, 10 insertions(+), 4 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/image/microtek.c b/drivers/usb/image/microtek.c index 5a47805d9580..c90c89dc0003 100644 --- a/drivers/usb/image/microtek.c +++ b/drivers/usb/image/microtek.c @@ -364,7 +364,7 @@ static int mts_scsi_host_reset(struct scsi_cmnd *srb) } static int -mts_scsi_queuecommand(struct scsi_cmnd *srb, mts_scsi_cmnd_callback callback); +mts_scsi_queuecommand(struct Scsi_Host *shost, struct scsi_cmnd *srb); static void mts_transfer_cleanup( struct urb *transfer ); static void mts_do_sg(struct urb * transfer); @@ -573,7 +573,7 @@ mts_build_transfer_context(struct scsi_cmnd *srb, struct mts_desc* desc) static int -mts_scsi_queuecommand(struct scsi_cmnd *srb, mts_scsi_cmnd_callback callback) +mts_scsi_queuecommand_lck(struct scsi_cmnd *srb, mts_scsi_cmnd_callback callback) { struct mts_desc* desc = (struct mts_desc*)(srb->device->host->hostdata[0]); int err = 0; @@ -626,6 +626,8 @@ out: return err; } +static DEF_SCSI_QCMD(mts_scsi_queuecommand) + static struct scsi_host_template mts_scsi_host_template = { .module = THIS_MODULE, .name = "microtekX6", diff --git a/drivers/usb/storage/scsiglue.c b/drivers/usb/storage/scsiglue.c index a688b1e686ea..689ee1fb702a 100644 --- a/drivers/usb/storage/scsiglue.c +++ b/drivers/usb/storage/scsiglue.c @@ -285,7 +285,7 @@ static int slave_configure(struct scsi_device *sdev) /* queue a command */ /* This is always called with scsi_lock(host) held */ -static int queuecommand(struct scsi_cmnd *srb, +static int queuecommand_lck(struct scsi_cmnd *srb, void (*done)(struct scsi_cmnd *)) { struct us_data *us = host_to_us(srb->device->host); @@ -315,6 +315,8 @@ static int queuecommand(struct scsi_cmnd *srb, return 0; } +static DEF_SCSI_QCMD(queuecommand) + /*********************************************************************** * Error handling functions ***********************************************************************/ diff --git a/drivers/usb/storage/uas.c b/drivers/usb/storage/uas.c index d1268191acbd..339fac3949df 100644 --- a/drivers/usb/storage/uas.c +++ b/drivers/usb/storage/uas.c @@ -430,7 +430,7 @@ static int uas_submit_urbs(struct scsi_cmnd *cmnd, return 0; } -static int uas_queuecommand(struct scsi_cmnd *cmnd, +static int uas_queuecommand_lck(struct scsi_cmnd *cmnd, void (*done)(struct scsi_cmnd *)) { struct scsi_device *sdev = cmnd->device; @@ -488,6 +488,8 @@ static int uas_queuecommand(struct scsi_cmnd *cmnd, return 0; } +static DEF_SCSI_QCMD(uas_queuecommand) + static int uas_eh_abort_handler(struct scsi_cmnd *cmnd) { struct scsi_device *sdev = cmnd->device; -- cgit v1.2.1 From 3d091a6f703906c5680855ff29bd94d051c8c6d8 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 8 Nov 2010 17:58:35 +0800 Subject: USB: EHCI: AMD periodic frame list table quirk On AMD SB700/SB800/Hudson-2/3 platforms, USB EHCI controller may read/write to memory space not allocated to USB controller if there is longer than normal latency on DMA read encountered. In this condition the exposure will be encountered only if the driver has following format of Periodic Frame List link pointer structure: For any idle periodic schedule, the Frame List link pointers that have the T-bit set to 1 intending to terminate the use of frame list link pointer as a physical memory pointer. Idle periodic schedule Frame List Link pointer shoule be in the following format to avoid the issue: Frame list link pointer should be always contains a valid pointer to a inactive QHead with T-bit set to 0. Signed-off-by: Andiry Xu Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-mem.c | 26 ++++++++++++++++++++++++-- drivers/usb/host/ehci-pci.c | 13 +++++++++++++ drivers/usb/host/ehci-sched.c | 21 ++++++++++++++++++--- drivers/usb/host/ehci.h | 2 ++ 4 files changed, 57 insertions(+), 5 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/ehci-mem.c b/drivers/usb/host/ehci-mem.c index d36e4e75e08d..12f70c302b0b 100644 --- a/drivers/usb/host/ehci-mem.c +++ b/drivers/usb/host/ehci-mem.c @@ -141,6 +141,10 @@ static void ehci_mem_cleanup (struct ehci_hcd *ehci) qh_put (ehci->async); ehci->async = NULL; + if (ehci->dummy) + qh_put(ehci->dummy); + ehci->dummy = NULL; + /* DMA consistent memory and pools */ if (ehci->qtd_pool) dma_pool_destroy (ehci->qtd_pool); @@ -227,8 +231,26 @@ static int ehci_mem_init (struct ehci_hcd *ehci, gfp_t flags) if (ehci->periodic == NULL) { goto fail; } - for (i = 0; i < ehci->periodic_size; i++) - ehci->periodic [i] = EHCI_LIST_END(ehci); + + if (ehci->use_dummy_qh) { + struct ehci_qh_hw *hw; + ehci->dummy = ehci_qh_alloc(ehci, flags); + if (!ehci->dummy) + goto fail; + + hw = ehci->dummy->hw; + hw->hw_next = EHCI_LIST_END(ehci); + hw->hw_qtd_next = EHCI_LIST_END(ehci); + hw->hw_alt_next = EHCI_LIST_END(ehci); + hw->hw_token &= ~QTD_STS_ACTIVE; + ehci->dummy->hw = hw; + + for (i = 0; i < ehci->periodic_size; i++) + ehci->periodic[i] = ehci->dummy->qh_dma; + } else { + for (i = 0; i < ehci->periodic_size; i++) + ehci->periodic[i] = EHCI_LIST_END(ehci); + } /* software shadow of hardware table */ ehci->pshadow = kcalloc(ehci->periodic_size, sizeof(void *), flags); diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index a1e8d273103f..01bb72b71832 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -103,6 +103,19 @@ static int ehci_pci_setup(struct usb_hcd *hcd) if (retval) return retval; + if ((pdev->vendor == PCI_VENDOR_ID_AMD && pdev->device == 0x7808) || + (pdev->vendor == PCI_VENDOR_ID_ATI && pdev->device == 0x4396)) { + /* EHCI controller on AMD SB700/SB800/Hudson-2/3 platforms may + * read/write memory space which does not belong to it when + * there is NULL pointer with T-bit set to 1 in the frame list + * table. To avoid the issue, the frame list link pointer + * should always contain a valid pointer to a inactive qh. + */ + ehci->use_dummy_qh = 1; + ehci_info(ehci, "applying AMD SB700/SB800/Hudson-2/3 EHCI " + "dummy qh workaround\n"); + } + /* data structure init */ retval = ehci_init(hcd); if (retval) diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c index a92526d6e5ae..d9f78eb26572 100644 --- a/drivers/usb/host/ehci-sched.c +++ b/drivers/usb/host/ehci-sched.c @@ -98,7 +98,14 @@ static void periodic_unlink (struct ehci_hcd *ehci, unsigned frame, void *ptr) */ *prev_p = *periodic_next_shadow(ehci, &here, Q_NEXT_TYPE(ehci, *hw_p)); - *hw_p = *shadow_next_periodic(ehci, &here, Q_NEXT_TYPE(ehci, *hw_p)); + + if (!ehci->use_dummy_qh || + *shadow_next_periodic(ehci, &here, Q_NEXT_TYPE(ehci, *hw_p)) + != EHCI_LIST_END(ehci)) + *hw_p = *shadow_next_periodic(ehci, &here, + Q_NEXT_TYPE(ehci, *hw_p)); + else + *hw_p = ehci->dummy->qh_dma; } /* how many of the uframe's 125 usecs are allocated? */ @@ -2335,7 +2342,11 @@ restart: * pointer for much longer, if at all. */ *q_p = q.itd->itd_next; - *hw_p = q.itd->hw_next; + if (!ehci->use_dummy_qh || + q.itd->hw_next != EHCI_LIST_END(ehci)) + *hw_p = q.itd->hw_next; + else + *hw_p = ehci->dummy->qh_dma; type = Q_NEXT_TYPE(ehci, q.itd->hw_next); wmb(); modified = itd_complete (ehci, q.itd); @@ -2368,7 +2379,11 @@ restart: * URB completion. */ *q_p = q.sitd->sitd_next; - *hw_p = q.sitd->hw_next; + if (!ehci->use_dummy_qh || + q.sitd->hw_next != EHCI_LIST_END(ehci)) + *hw_p = q.sitd->hw_next; + else + *hw_p = ehci->dummy->qh_dma; type = Q_NEXT_TYPE(ehci, q.sitd->hw_next); wmb(); modified = sitd_complete (ehci, q.sitd); diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h index bde823f704e9..ba8eab366b82 100644 --- a/drivers/usb/host/ehci.h +++ b/drivers/usb/host/ehci.h @@ -73,6 +73,7 @@ struct ehci_hcd { /* one per controller */ /* async schedule support */ struct ehci_qh *async; + struct ehci_qh *dummy; /* For AMD quirk use */ struct ehci_qh *reclaim; unsigned scanning : 1; @@ -131,6 +132,7 @@ struct ehci_hcd { /* one per controller */ unsigned need_io_watchdog:1; unsigned broken_periodic:1; unsigned fs_i_thresh:1; /* Intel iso scheduling */ + unsigned use_dummy_qh:1; /* AMD Frame List table quirk*/ /* required for usb32 quirk */ #define OHCI_CTRL_HCFS (3 << 6) -- cgit v1.2.1 From f52022b53bac3228620e490abbe2ccb1e87ab060 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Tue, 9 Nov 2010 09:16:39 +0800 Subject: USB: isp1362-hcd - fix section mismatch warning Fix section mismatch warning by using "__devinit" annotation for isp1362_probe. WARNING: drivers/usb/host/isp1362-hcd.o(.data+0x0): Section mismatch in reference from the variable isp1362_driver to the function .init.text:isp1362_probe() The variable isp1362_driver references the function __init isp1362_probe() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Axel Lin Acked-by: Mike Frysinger Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/isp1362-hcd.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/isp1362-hcd.c b/drivers/usb/host/isp1362-hcd.c index 8196fa11fec4..97cce59ff767 100644 --- a/drivers/usb/host/isp1362-hcd.c +++ b/drivers/usb/host/isp1362-hcd.c @@ -2684,7 +2684,7 @@ static int __devexit isp1362_remove(struct platform_device *pdev) return 0; } -static int __init isp1362_probe(struct platform_device *pdev) +static int __devinit isp1362_probe(struct platform_device *pdev) { struct usb_hcd *hcd; struct isp1362_hcd *isp1362_hcd; -- cgit v1.2.1 From b48809518631880207796b4aab0fc39c2f036754 Mon Sep 17 00:00:00 2001 From: Josh Wu Date: Tue, 16 Nov 2010 11:51:32 +0100 Subject: USB: gadget: AT91: fix typo in atmel_usba_udc driver compile fix for bug introduced by 969affff547027) Signed-off-by: Josh Wu Cc: Jiri Kosina Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/atmel_usba_udc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/gadget/atmel_usba_udc.c b/drivers/usb/gadget/atmel_usba_udc.c index b5e20e873cba..717ff653fa23 100644 --- a/drivers/usb/gadget/atmel_usba_udc.c +++ b/drivers/usb/gadget/atmel_usba_udc.c @@ -2017,7 +2017,7 @@ static int __init usba_udc_probe(struct platform_device *pdev) } } else { /* gpio_request fail so use -EINVAL for gpio_is_valid */ - ubc->vbus_pin = -EINVAL; + udc->vbus_pin = -EINVAL; } } -- cgit v1.2.1 From 02e2c51ba3e80acde600721ea784c3ef84da5ea1 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 16 Nov 2010 10:57:37 -0500 Subject: USB: EHCI: fix obscure race in ehci_endpoint_disable This patch (as1435) fixes an obscure and unlikely race in ehci-hcd. When an async URB is unlinked, the corresponding QH is removed from the async list. If the QH's endpoint is then disabled while the URB is being given back, ehci_endpoint_disable() won't find the QH on the async list, causing it to believe that the QH has been lost. This will lead to a memory leak at best and quite possibly to an oops. The solution is to trust usbcore not to lose track of endpoints. If the QH isn't on the async list then it doesn't need to be taken off the list, but the driver should still wait for the QH to become IDLE before disabling it. In theory this fixes Bugzilla #20182. In fact the race is so rare that it's not possible to tell whether the bug is still present. However, adding delays and making other changes to force the race seems to show that the patch works. Signed-off-by: Alan Stern Reported-by: Stefan Richter CC: David Brownell CC: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hcd.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 502a7e6fef42..e9062806d4a2 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -1063,10 +1063,11 @@ rescan: tmp && tmp != qh; tmp = tmp->qh_next.qh) continue; - /* periodic qh self-unlinks on empty */ - if (!tmp) - goto nogood; - unlink_async (ehci, qh); + /* periodic qh self-unlinks on empty, and a COMPLETING qh + * may already be unlinked. + */ + if (tmp) + unlink_async(ehci, qh); /* FALL THROUGH */ case QH_STATE_UNLINK: /* wait for hw to finish? */ case QH_STATE_UNLINK_WAIT: @@ -1083,7 +1084,6 @@ idle_timeout: } /* else FALL THROUGH */ default: -nogood: /* caller was supposed to have unlinked any requests; * that's not our job. just leak this memory. */ -- cgit v1.2.1 From 451a3c24b0135bce54542009b5fde43846c7cf67 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 17 Nov 2010 16:26:55 +0100 Subject: BKL: remove extraneous #include The big kernel lock has been removed from all these files at some point, leaving only the #include. Remove this too as a cleanup. Signed-off-by: Arnd Bergmann Signed-off-by: Linus Torvalds --- drivers/usb/core/devices.c | 1 - drivers/usb/core/devio.c | 1 - drivers/usb/core/file.c | 1 - drivers/usb/core/inode.c | 1 - drivers/usb/gadget/f_fs.c | 1 - drivers/usb/gadget/f_hid.c | 1 - drivers/usb/host/isp1362-hcd.c | 1 - drivers/usb/host/uhci-debug.c | 1 - drivers/usb/mon/mon_bin.c | 1 - drivers/usb/mon/mon_stat.c | 1 - drivers/usb/serial/usb-serial.c | 1 - 11 files changed, 11 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/core/devices.c b/drivers/usb/core/devices.c index ddb4dc980923..a3d2e2399655 100644 --- a/drivers/usb/core/devices.c +++ b/drivers/usb/core/devices.c @@ -54,7 +54,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 045bb4b823e1..a7131ad630f9 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -37,7 +37,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/usb/core/file.c b/drivers/usb/core/file.c index 9fe34fb78ef1..cf6a5423de09 100644 --- a/drivers/usb/core/file.c +++ b/drivers/usb/core/file.c @@ -19,7 +19,6 @@ #include #include #include -#include #include #include "usb.h" diff --git a/drivers/usb/core/inode.c b/drivers/usb/core/inode.c index 9819a4cc3b26..b690aa35df9a 100644 --- a/drivers/usb/core/inode.c +++ b/drivers/usb/core/inode.c @@ -39,7 +39,6 @@ #include #include #include -#include #include #include #include "usb.h" diff --git a/drivers/usb/gadget/f_fs.c b/drivers/usb/gadget/f_fs.c index 4a830df4fc31..484c5ba5450e 100644 --- a/drivers/usb/gadget/f_fs.c +++ b/drivers/usb/gadget/f_fs.c @@ -30,7 +30,6 @@ #include #include #include -#include #include #include diff --git a/drivers/usb/gadget/f_hid.c b/drivers/usb/gadget/f_hid.c index 4f891eddd060..598e7e2ab80c 100644 --- a/drivers/usb/gadget/f_hid.c +++ b/drivers/usb/gadget/f_hid.c @@ -25,7 +25,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/usb/host/isp1362-hcd.c b/drivers/usb/host/isp1362-hcd.c index 8196fa11fec4..6c4fb4efb4bb 100644 --- a/drivers/usb/host/isp1362-hcd.c +++ b/drivers/usb/host/isp1362-hcd.c @@ -70,7 +70,6 @@ #include #include #include -#include #include #include #include diff --git a/drivers/usb/host/uhci-debug.c b/drivers/usb/host/uhci-debug.c index 6e7fb5f38db6..ee60cd3ea642 100644 --- a/drivers/usb/host/uhci-debug.c +++ b/drivers/usb/host/uhci-debug.c @@ -12,7 +12,6 @@ #include #include #include -#include #include #include "uhci-hcd.h" diff --git a/drivers/usb/mon/mon_bin.c b/drivers/usb/mon/mon_bin.c index 44cb37b5a4dc..c436e1e2c3b6 100644 --- a/drivers/usb/mon/mon_bin.c +++ b/drivers/usb/mon/mon_bin.c @@ -15,7 +15,6 @@ #include #include #include -#include #include #include diff --git a/drivers/usb/mon/mon_stat.c b/drivers/usb/mon/mon_stat.c index 8ec94f15a738..e5ce42bd316e 100644 --- a/drivers/usb/mon/mon_stat.c +++ b/drivers/usb/mon/mon_stat.c @@ -11,7 +11,6 @@ #include #include #include -#include #include #include "usb_mon.h" diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index e64da74bdcc5..861223f2af6e 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -21,7 +21,6 @@ #include #include #include -#include #include #include #include -- cgit v1.2.1 From 7a3783efffc7bc2e702d774e47fad5b8e37e9ad1 Mon Sep 17 00:00:00 2001 From: Paul Zimmerman Date: Wed, 17 Nov 2010 16:26:50 -0800 Subject: xhci: Fix reset-device and configure-endpoint commands We have been having problems with the USB-IF Gold Tree tests when plugging and unplugging devices from the tree. I have seen that the reset-device and configure-endpoint commands, which are invoked from xhci_discover_or_reset_device() and xhci_configure_endpoint(), will sometimes time out. After much debugging, I determined that the commands themselves do not actually time out, but rather their completion events do not get delivered to the right place. This happens when the command ring has just wrapped around, and it's enqueue pointer is left pointing to the link TRB. xhci_discover_or_reset_device() and xhci_configure_endpoint() use the enqueue pointer directly as their command TRB pointer, without checking whether it's pointing to the link TRB. When the completion event arrives, if the command TRB is pointing to the link TRB, the check against the command ring dequeue pointer in handle_cmd_in_cmd_wait_list() fails, so the completion inside the command does not get signaled. The patch below fixes the timeout problem for me. This should be queued for the 2.6.35 and 2.6.36 stable trees. Signed-off-by: Paul Zimmerman Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 06fca0835b52..45e4a3108cc3 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -1549,6 +1549,15 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, cmd_completion = command->completion; cmd_status = &command->status; command->command_trb = xhci->cmd_ring->enqueue; + + /* Enqueue pointer can be left pointing to the link TRB, + * we must handle that + */ + if ((command->command_trb->link.control & TRB_TYPE_BITMASK) + == TRB_TYPE(TRB_LINK)) + command->command_trb = + xhci->cmd_ring->enq_seg->next->trbs; + list_add_tail(&command->cmd_list, &virt_dev->cmd_list); } else { in_ctx = virt_dev->in_ctx; @@ -2272,6 +2281,15 @@ int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev) /* Attempt to submit the Reset Device command to the command ring */ spin_lock_irqsave(&xhci->lock, flags); reset_device_cmd->command_trb = xhci->cmd_ring->enqueue; + + /* Enqueue pointer can be left pointing to the link TRB, + * we must handle that + */ + if ((reset_device_cmd->command_trb->link.control & TRB_TYPE_BITMASK) + == TRB_TYPE(TRB_LINK)) + reset_device_cmd->command_trb = + xhci->cmd_ring->enq_seg->next->trbs; + list_add_tail(&reset_device_cmd->cmd_list, &virt_dev->cmd_list); ret = xhci_queue_reset_device(xhci, slot_id); if (ret) { -- cgit v1.2.1 From da6699ce4a889c3795624ccdcfe7181cc89f18e8 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 26 Oct 2010 16:47:13 -0700 Subject: xhci: Setup array of USB 2.0 and USB 3.0 ports. An xHCI host controller contains USB 2.0 and USB 3.0 ports, which can occur in any order in the PORTSC registers. We cannot read the port speed bits in the PORTSC registers at init time to determine the port speed, since those bits are only valid when a USB device is plugged into the port. Instead, we read the "Supported Protocol Capability" registers in the xHC Extended Capabilities space. Those describe the protocol, port offset in the PORTSC registers, and port count. We use those registers to create two arrays of pointers to the PORTSC registers, one for USB 3.0 ports, and another for USB 2.0 ports. A third array keeps track of the port protocol major revision, and is indexed with the internal xHCI port number. This commit is a bit big, but it should be queued for stable because the "Don't let the USB core disable SuperSpeed ports" patch depends on it. There is no other way to determine which ports are SuperSpeed ports without this patch. Signed-off-by: Sarah Sharp Tested-by: Don Zickus Cc: stable@kernel.org --- drivers/usb/host/xhci-mem.c | 164 ++++++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/xhci.h | 26 +++++++ 2 files changed, 190 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index d178761c3981..0fae58ef8afe 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1443,6 +1443,13 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->dcbaa = NULL; scratchpad_free(xhci); + + xhci->num_usb2_ports = 0; + xhci->num_usb3_ports = 0; + kfree(xhci->usb2_ports); + kfree(xhci->usb3_ports); + kfree(xhci->port_array); + xhci->page_size = 0; xhci->page_shift = 0; xhci->bus_suspended = 0; @@ -1627,6 +1634,161 @@ static void xhci_set_hc_event_deq(struct xhci_hcd *xhci) &xhci->ir_set->erst_dequeue); } +static void xhci_add_in_port(struct xhci_hcd *xhci, unsigned int num_ports, + u32 __iomem *addr, u8 major_revision) +{ + u32 temp, port_offset, port_count; + int i; + + if (major_revision > 0x03) { + xhci_warn(xhci, "Ignoring unknown port speed, " + "Ext Cap %p, revision = 0x%x\n", + addr, major_revision); + /* Ignoring port protocol we can't understand. FIXME */ + return; + } + + /* Port offset and count in the third dword, see section 7.2 */ + temp = xhci_readl(xhci, addr + 2); + port_offset = XHCI_EXT_PORT_OFF(temp); + port_count = XHCI_EXT_PORT_COUNT(temp); + xhci_dbg(xhci, "Ext Cap %p, port offset = %u, " + "count = %u, revision = 0x%x\n", + addr, port_offset, port_count, major_revision); + /* Port count includes the current port offset */ + if (port_offset == 0 || (port_offset + port_count - 1) > num_ports) + /* WTF? "Valid values are ‘1’ to MaxPorts" */ + return; + port_offset--; + for (i = port_offset; i < (port_offset + port_count); i++) { + /* Duplicate entry. Ignore the port if the revisions differ. */ + if (xhci->port_array[i] != 0) { + xhci_warn(xhci, "Duplicate port entry, Ext Cap %p," + " port %u\n", addr, i); + xhci_warn(xhci, "Port was marked as USB %u, " + "duplicated as USB %u\n", + xhci->port_array[i], major_revision); + /* Only adjust the roothub port counts if we haven't + * found a similar duplicate. + */ + if (xhci->port_array[i] != major_revision && + xhci->port_array[i] != (u8) -1) { + if (xhci->port_array[i] == 0x03) + xhci->num_usb3_ports--; + else + xhci->num_usb2_ports--; + xhci->port_array[i] = (u8) -1; + } + /* FIXME: Should we disable the port? */ + } + xhci->port_array[i] = major_revision; + if (major_revision == 0x03) + xhci->num_usb3_ports++; + else + xhci->num_usb2_ports++; + } + /* FIXME: Should we disable ports not in the Extended Capabilities? */ +} + +/* + * Scan the Extended Capabilities for the "Supported Protocol Capabilities" that + * specify what speeds each port is supposed to be. We can't count on the port + * speed bits in the PORTSC register being correct until a device is connected, + * but we need to set up the two fake roothubs with the correct number of USB + * 3.0 and USB 2.0 ports at host controller initialization time. + */ +static int xhci_setup_port_arrays(struct xhci_hcd *xhci, gfp_t flags) +{ + u32 __iomem *addr; + u32 offset; + unsigned int num_ports; + int i, port_index; + + addr = &xhci->cap_regs->hcc_params; + offset = XHCI_HCC_EXT_CAPS(xhci_readl(xhci, addr)); + if (offset == 0) { + xhci_err(xhci, "No Extended Capability registers, " + "unable to set up roothub.\n"); + return -ENODEV; + } + + num_ports = HCS_MAX_PORTS(xhci->hcs_params1); + xhci->port_array = kzalloc(sizeof(*xhci->port_array)*num_ports, flags); + if (!xhci->port_array) + return -ENOMEM; + + /* + * For whatever reason, the first capability offset is from the + * capability register base, not from the HCCPARAMS register. + * See section 5.3.6 for offset calculation. + */ + addr = &xhci->cap_regs->hc_capbase + offset; + while (1) { + u32 cap_id; + + cap_id = xhci_readl(xhci, addr); + if (XHCI_EXT_CAPS_ID(cap_id) == XHCI_EXT_CAPS_PROTOCOL) + xhci_add_in_port(xhci, num_ports, addr, + (u8) XHCI_EXT_PORT_MAJOR(cap_id)); + offset = XHCI_EXT_CAPS_NEXT(cap_id); + if (!offset || (xhci->num_usb2_ports + xhci->num_usb3_ports) + == num_ports) + break; + /* + * Once you're into the Extended Capabilities, the offset is + * always relative to the register holding the offset. + */ + addr += offset; + } + + if (xhci->num_usb2_ports == 0 && xhci->num_usb3_ports == 0) { + xhci_warn(xhci, "No ports on the roothubs?\n"); + return -ENODEV; + } + xhci_dbg(xhci, "Found %u USB 2.0 ports and %u USB 3.0 ports.\n", + xhci->num_usb2_ports, xhci->num_usb3_ports); + /* + * Note we could have all USB 3.0 ports, or all USB 2.0 ports. + * Not sure how the USB core will handle a hub with no ports... + */ + if (xhci->num_usb2_ports) { + xhci->usb2_ports = kmalloc(sizeof(*xhci->usb2_ports)* + xhci->num_usb2_ports, flags); + if (!xhci->usb2_ports) + return -ENOMEM; + + port_index = 0; + for (i = 0; i < num_ports; i++) + if (xhci->port_array[i] != 0x03) { + xhci->usb2_ports[port_index] = + &xhci->op_regs->port_status_base + + NUM_PORT_REGS*i; + xhci_dbg(xhci, "USB 2.0 port at index %u, " + "addr = %p\n", i, + xhci->usb2_ports[port_index]); + port_index++; + } + } + if (xhci->num_usb3_ports) { + xhci->usb3_ports = kmalloc(sizeof(*xhci->usb3_ports)* + xhci->num_usb3_ports, flags); + if (!xhci->usb3_ports) + return -ENOMEM; + + port_index = 0; + for (i = 0; i < num_ports; i++) + if (xhci->port_array[i] == 0x03) { + xhci->usb3_ports[port_index] = + &xhci->op_regs->port_status_base + + NUM_PORT_REGS*i; + xhci_dbg(xhci, "USB 3.0 port at index %u, " + "addr = %p\n", i, + xhci->usb3_ports[port_index]); + port_index++; + } + } + return 0; +} int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) { @@ -1809,6 +1971,8 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) if (scratchpad_alloc(xhci, flags)) goto fail; + if (xhci_setup_port_arrays(xhci, flags)) + goto fail; return 0; diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 85e65647d445..170c367112d2 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -453,6 +453,24 @@ struct xhci_doorbell_array { #define STREAM_ID_TO_DB(p) (((p) & 0xffff) << 16) +/** + * struct xhci_protocol_caps + * @revision: major revision, minor revision, capability ID, + * and next capability pointer. + * @name_string: Four ASCII characters to say which spec this xHC + * follows, typically "USB ". + * @port_info: Port offset, count, and protocol-defined information. + */ +struct xhci_protocol_caps { + u32 revision; + u32 name_string; + u32 port_info; +}; + +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) +#define XHCI_EXT_PORT_OFF(x) ((x) & 0xff) +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) + /** * struct xhci_container_ctx * @type: Type of context. Used to calculated offsets to contained contexts. @@ -1240,6 +1258,14 @@ struct xhci_hcd { u32 suspended_ports[8]; /* which ports are suspended */ unsigned long resume_done[MAX_HC_PORTS]; + /* Is each xHCI roothub port a USB 3.0, USB 2.0, or USB 1.1 port? */ + u8 *port_array; + /* Array of pointers to USB 3.0 PORTSC registers */ + u32 __iomem **usb3_ports; + unsigned int num_usb3_ports; + /* Array of pointers to USB 2.0 PORTSC registers */ + u32 __iomem **usb2_ports; + unsigned int num_usb2_ports; }; /* For testing purposes */ -- cgit v1.2.1 From 6dd0a3a7e0793dbeae1b951f091025d8cf896cb4 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 16 Nov 2010 15:58:52 -0800 Subject: xhci: Don't let the USB core disable SuperSpeed ports. Disabling SuperSpeed ports is a Very Bad Thing (TM). It disables SuperSpeed terminations, which means that devices will never connect at SuperSpeed on that port. For USB 2.0/1.1 ports, disabling the port meant that the USB core could always get a connect status change later. That's not true with USB 3.0 ports. Do not let the USB core disable SuperSpeed ports. We can't rely on the device speed in the port status registers, since that isn't valid until there's a USB device connected to the port. Instead, we use the port speed array that's created from the Extended Capabilities registers. Signed-off-by: Sarah Sharp Tested-by: Don Zickus Cc: stable@kernel.org --- drivers/usb/host/xhci-hub.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c index fef5a1f9d483..5d963e350494 100644 --- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -229,6 +229,13 @@ void xhci_ring_device(struct xhci_hcd *xhci, int slot_id) static void xhci_disable_port(struct xhci_hcd *xhci, u16 wIndex, u32 __iomem *addr, u32 port_status) { + /* Don't allow the USB core to disable SuperSpeed ports. */ + if (xhci->port_array[wIndex] == 0x03) { + xhci_dbg(xhci, "Ignoring request to disable " + "SuperSpeed port.\n"); + return; + } + /* Write 1 to disable the port */ xhci_writel(xhci, port_status | PORT_PE, addr); port_status = xhci_readl(xhci, addr); -- cgit v1.2.1 From 92d2711f5dc15bf956546923a5718e74853f9912 Mon Sep 17 00:00:00 2001 From: Hema Kalliguddi Date: Mon, 15 Nov 2010 04:24:01 -0600 Subject: usb: musb: unmap dma buffer when switching to PIO Buffer is mapped to dma when dma channel is allocated. If, for some reason, dma channel programming fails, musb code will fallback to PIO mode to transfer that request. In that case, we need to unmap the buffer back to CPU. MUSB RTL1.8 and above cannot handle buffers which are not 32bit aligned. That happens to every request sent by g_ether gadget driver. Since the buffer sent was unaligned, we need to fallback to PIO. Because of that, g_ether was failing due to missing buffer unmapping. With this patch and [1] g_ether works fine with all MUSB revisions. Verified with OMAP3630 board, which has MUSB RTL1.8 using g_ether and g_zero. [1] http://www.spinics.net/lists/linux-usb/msg38400.html Signed-off-by: Hema HK Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_gadget.c | 117 ++++++++++++++++++++++++++++------------- 1 file changed, 79 insertions(+), 38 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 36cfd060dbe5..0169dcf3a6ff 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -92,6 +92,59 @@ /* ----------------------------------------------------------------------- */ +/* Maps the buffer to dma */ + +static inline void map_dma_buffer(struct musb_request *request, + struct musb *musb) +{ + if (request->request.dma == DMA_ADDR_INVALID) { + request->request.dma = dma_map_single( + musb->controller, + request->request.buf, + request->request.length, + request->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + request->mapped = 1; + } else { + dma_sync_single_for_device(musb->controller, + request->request.dma, + request->request.length, + request->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + request->mapped = 0; + } +} + +/* Unmap the buffer from dma and maps it back to cpu */ +static inline void unmap_dma_buffer(struct musb_request *request, + struct musb *musb) +{ + if (request->request.dma == DMA_ADDR_INVALID) { + DBG(20, "not unmapping a never mapped buffer\n"); + return; + } + if (request->mapped) { + dma_unmap_single(musb->controller, + request->request.dma, + request->request.length, + request->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + request->request.dma = DMA_ADDR_INVALID; + request->mapped = 0; + } else { + dma_sync_single_for_cpu(musb->controller, + request->request.dma, + request->request.length, + request->tx + ? DMA_TO_DEVICE + : DMA_FROM_DEVICE); + + } +} + /* * Immediately complete a request. * @@ -119,24 +172,8 @@ __acquires(ep->musb->lock) ep->busy = 1; spin_unlock(&musb->lock); - if (is_dma_capable()) { - if (req->mapped) { - dma_unmap_single(musb->controller, - req->request.dma, - req->request.length, - req->tx - ? DMA_TO_DEVICE - : DMA_FROM_DEVICE); - req->request.dma = DMA_ADDR_INVALID; - req->mapped = 0; - } else if (req->request.dma != DMA_ADDR_INVALID) - dma_sync_single_for_cpu(musb->controller, - req->request.dma, - req->request.length, - req->tx - ? DMA_TO_DEVICE - : DMA_FROM_DEVICE); - } + if (is_dma_capable() && ep->dma) + unmap_dma_buffer(req, musb); if (request->status == 0) DBG(5, "%s done request %p, %d/%d\n", ep->end_point.name, request, @@ -395,6 +432,13 @@ static void txstate(struct musb *musb, struct musb_request *req) #endif if (!use_dma) { + /* + * Unmap the dma buffer back to cpu if dma channel + * programming fails + */ + if (is_dma_capable() && musb_ep->dma) + unmap_dma_buffer(req, musb); + musb_write_fifo(musb_ep->hw_ep, fifo_count, (u8 *) (request->buf + request->actual)); request->actual += fifo_count; @@ -713,6 +757,20 @@ static void rxstate(struct musb *musb, struct musb_request *req) return; } #endif + /* + * Unmap the dma buffer back to cpu if dma channel + * programming fails. This buffer is mapped if the + * channel allocation is successful + */ + if (is_dma_capable() && musb_ep->dma) { + unmap_dma_buffer(req, musb); + + /* Clear DMAENAB for the + * PIO mode transfer + */ + csr &= ~MUSB_RXCSR_DMAENAB; + musb_writew(epio, MUSB_RXCSR, csr); + } musb_read_fifo(musb_ep->hw_ep, fifo_count, (u8 *) (request->buf + request->actual)); @@ -1150,26 +1208,9 @@ static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req, request->epnum = musb_ep->current_epnum; request->tx = musb_ep->is_in; - if (is_dma_capable() && musb_ep->dma) { - if (request->request.dma == DMA_ADDR_INVALID) { - request->request.dma = dma_map_single( - musb->controller, - request->request.buf, - request->request.length, - request->tx - ? DMA_TO_DEVICE - : DMA_FROM_DEVICE); - request->mapped = 1; - } else { - dma_sync_single_for_device(musb->controller, - request->request.dma, - request->request.length, - request->tx - ? DMA_TO_DEVICE - : DMA_FROM_DEVICE); - request->mapped = 0; - } - } else + if (is_dma_capable() && musb_ep->dma) + map_dma_buffer(request, musb); + else request->mapped = 0; spin_lock_irqsave(&musb->lock, lockflags); -- cgit v1.2.1 From e75df37165c639b06213ec88b4763c3e50a7f079 Mon Sep 17 00:00:00 2001 From: Ming Lei Date: Tue, 16 Nov 2010 23:37:37 +0800 Subject: usb: musb: clear RXCSR_AUTOCLEAR before PIO read If RXCSR_AUTOCLEAR flag is not cleard before PIO reading, one packet may be recieved by musb fifo, but no chance to notify software, so cause packet loss, follows the detailed process: - PIO read one packet - musb fifo auto clear the MUSB_RXCSR_RXPKTRDY - musb continue to recieve the next packet, and MUSB_RXCSR_RXPKTRDY is set - software clear the MUSB_RXCSR_RXPKTRDY, so there is no chance for musb to notify software that the 2nd recieved packet. The patch does fix the g_ether issue below: - use fifo_mode 3 to enable double buffer - 'ping -s 1024 IP_OF_BEAGLE_XM' - one usb packet of 512 byte is lost, so ping failed, which can be observed by wireshark note: Beagle xm takes musb rtl1.8 and may fallback to pio mode for unaligned buffer. Signed-off-by: Ming Lei Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_gadget.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 0169dcf3a6ff..363cfad003f8 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -765,10 +765,11 @@ static void rxstate(struct musb *musb, struct musb_request *req) if (is_dma_capable() && musb_ep->dma) { unmap_dma_buffer(req, musb); - /* Clear DMAENAB for the + /* + * Clear DMAENAB and AUTOCLEAR for the * PIO mode transfer */ - csr &= ~MUSB_RXCSR_DMAENAB; + csr &= ~(MUSB_RXCSR_DMAENAB | MUSB_RXCSR_AUTOCLEAR); musb_writew(epio, MUSB_RXCSR, csr); } -- cgit v1.2.1 From bb324b08165d5656d221af013ed9994a54e455be Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Mon, 22 Nov 2010 14:22:41 +0530 Subject: usb: musb: gadget: fix compilation warning Fixes below compilation warning when musb driver is compiled for PIO mode: drivers/usb/musb/musb_gadget.c: In function 'musb_g_rx': drivers/usb/musb/musb_gadget.c:840: warning: label 'exit' defined but not used Signed-off-by: Ajay Kumar Gupta Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_gadget.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index 363cfad003f8..c8de0e123f2c 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -896,7 +896,9 @@ void musb_g_rx(struct musb *musb, u8 epnum) if (!request) return; } +#if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_TUSB_OMAP_DMA) exit: +#endif /* Analyze request */ rxstate(musb, to_musb_request(request)); } -- cgit v1.2.1 From 07a8cdd2bb17a4da68136d963b8bc71959bd31a5 Mon Sep 17 00:00:00 2001 From: Anand Gadiyar Date: Thu, 18 Nov 2010 18:54:17 +0530 Subject: usb: musb: do not use dma for control transfers The Inventra DMA engine used with the MUSB controller in many SoCs cannot use DMA for control transfers on EP0, but can use DMA for all other transfers. The USB core maps urbs for DMA if hcd->self.uses_dma is true. (hcd->self.uses_dma is true for MUSB as well). Split the uses_dma flag into two - one that says if the controller needs to use PIO for control transfers, and another which says if the controller uses DMA (for all other transfers). Also, populate this flag for all MUSB by default. (Tested on OMAP3 and OMAP4 boards, with EHCI and MUSB HCDs simultaneously in use). Signed-off-by: Maulik Mankad Signed-off-by: Santosh Shilimkar Signed-off-by: Anand Gadiyar Cc: Oliver Neukum Cc: Alan Stern Cc: Praveena NADAHALLY Cc: Ajay Kumar Gupta Signed-off-by: Felipe Balbi --- drivers/usb/core/hcd.c | 2 ++ drivers/usb/musb/musb_core.c | 3 +++ drivers/usb/musb/musb_gadget.c | 4 ++++ 3 files changed, 9 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index 61800f77dac8..ced846ac4141 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -1330,6 +1330,8 @@ static int map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb, */ if (usb_endpoint_xfer_control(&urb->ep->desc)) { + if (hcd->self.uses_pio_for_control) + return ret; if (hcd->self.uses_dma) { urb->setup_dma = dma_map_single( hcd->self.controller, diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index e6669fc3b804..99beebce8550 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -2116,12 +2116,15 @@ bad_config: * Otherwise, wait till the gadget driver hooks up. */ if (!is_otg_enabled(musb) && is_host_enabled(musb)) { + struct usb_hcd *hcd = musb_to_hcd(musb); + MUSB_HST_MODE(musb); musb->xceiv->default_a = 1; musb->xceiv->state = OTG_STATE_A_IDLE; status = usb_add_hcd(musb_to_hcd(musb), -1, 0); + hcd->self.uses_pio_for_control = 1; DBG(1, "%s mode, status %d, devctl %02x %c\n", "HOST", status, musb_readb(musb->mregs, MUSB_DEVCTL), diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c index c8de0e123f2c..9d6ade82b9f2 100644 --- a/drivers/usb/musb/musb_gadget.c +++ b/drivers/usb/musb/musb_gadget.c @@ -1833,6 +1833,8 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, spin_unlock_irqrestore(&musb->lock, flags); if (is_otg_enabled(musb)) { + struct usb_hcd *hcd = musb_to_hcd(musb); + DBG(3, "OTG startup...\n"); /* REVISIT: funcall to other code, which also @@ -1847,6 +1849,8 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, musb->gadget_driver = NULL; musb->g.dev.driver = NULL; spin_unlock_irqrestore(&musb->lock, flags); + } else { + hcd->self.uses_pio_for_control = 1; } } } -- cgit v1.2.1 From 28942bb6a9dd4e2ed793675e515cfb8297ed355b Mon Sep 17 00:00:00 2001 From: Michael Stuermer Date: Thu, 18 Nov 2010 00:45:43 +0100 Subject: USB: ftdi_sio: Add ID for RT Systems USB-29B radio cable Another variant of the RT Systems programming cable for ham radios. Signed-off-by: Michael Stuermer Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio_ids.h | 1 + 2 files changed, 2 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 76f8b3556672..1c5892a2deea 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -696,6 +696,7 @@ static struct usb_device_id id_table_combined [] = { .driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk }, { USB_DEVICE(TELLDUS_VID, TELLDUS_TELLSTICK_PID) }, { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_SERIAL_VX7_PID) }, + { USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_CT29B_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MAXSTREAM_PID) }, { USB_DEVICE(FTDI_VID, FTDI_PHI_FISCO_PID) }, { USB_DEVICE(TML_VID, TML_USB_SERIAL_PID) }, diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index 263f62551197..cee062fbbb4e 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -721,6 +721,7 @@ */ #define RTSYSTEMS_VID 0x2100 /* Vendor ID */ #define RTSYSTEMS_SERIAL_VX7_PID 0x9e52 /* Serial converter for VX-7 Radios using FT232RL */ +#define RTSYSTEMS_CT29B_PID 0x9e54 /* CT29B Radio Cable */ /* * Bayer Ascensia Contour blood glucose meter USB-converter cable. -- cgit v1.2.1 From 27f485b5b27926878ffc8f528bdefeb25e6bd3d3 Mon Sep 17 00:00:00 2001 From: Tomoki Sekiyama Date: Mon, 22 Nov 2010 19:29:23 +0900 Subject: USB: yurex: add .llseek fop to file_operations Default llseek operation behavior was changed by the patch named "vfs: make no_llseek the default" after the yurex driver had been merged, so the llseek to yurex is now ignored. This patch add llseek fop with default_llseek to yurex driver to catch up to the change. Signed-off-by: Tomoki Sekiyama Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/yurex.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/usb') diff --git a/drivers/usb/misc/yurex.c b/drivers/usb/misc/yurex.c index 719c6180b31f..ac5bfd619e62 100644 --- a/drivers/usb/misc/yurex.c +++ b/drivers/usb/misc/yurex.c @@ -536,6 +536,7 @@ static const struct file_operations yurex_fops = { .open = yurex_open, .release = yurex_release, .fasync = yurex_fasync, + .llseek = default_llseek, }; -- cgit v1.2.1 From 6fdbad8021151a9e93af8159a6232c8f26415c09 Mon Sep 17 00:00:00 2001 From: Jacques Viviers Date: Wed, 24 Nov 2010 11:56:38 +0200 Subject: USB: serial: ftdi_sio: Vardaan USB RS422/485 converter PID added Add the PID for the Vardaan Enterprises VEUSB422R3 USB to RS422/485 converter. It uses the same chip as the FTDI_8U232AM_PID 0x6001. This should also work with the stable branches for: 2.6.31, 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36 Signed-off-by: Jacques Viviers Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio_ids.h | 3 +++ 2 files changed, 4 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 1c5892a2deea..6a50965e23f2 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -201,6 +201,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_MTXORB_5_PID) }, { USB_DEVICE(FTDI_VID, FTDI_MTXORB_6_PID) }, { USB_DEVICE(FTDI_VID, FTDI_R2000KU_TRUE_RNG) }, + { USB_DEVICE(FTDI_VID, FTDI_VARDAAN_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0100_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0101_PID) }, { USB_DEVICE(MTXORB_VID, MTXORB_FTDI_RANGE_0102_PID) }, diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index cee062fbbb4e..1286f1e23d8c 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -114,6 +114,9 @@ /* Lenz LI-USB Computer Interface. */ #define FTDI_LENZ_LIUSB_PID 0xD780 +/* Vardaan Enterprises Serial Interface VEUSB422R3 */ +#define FTDI_VARDAAN_PID 0xF070 + /* * Xsens Technologies BV products (http://www.xsens.com). */ -- cgit v1.2.1 From a85b4e7f4481c5a1ca89fa63c9c871151965075e Mon Sep 17 00:00:00 2001 From: "Brian J. Tarricone" Date: Sun, 21 Nov 2010 21:15:52 -0800 Subject: USB: ehci: disable LPM and PPCD for nVidia MCP89 chips Tested on MacBookAir3,1. Without this, we get EPROTO errors when fetching device config descriptors. Signed-off-by: Brian Tarricone Reported-by: Benoit Gschwind Tested-by: Edgar Hucek Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-pci.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 01bb72b71832..655f3c9f88bf 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -161,6 +161,18 @@ static int ehci_pci_setup(struct usb_hcd *hcd) if (pdev->revision < 0xa4) ehci->no_selective_suspend = 1; break; + + /* MCP89 chips on the MacBookAir3,1 give EPROTO when + * fetching device descriptors unless LPM is disabled. + * There are also intermittent problems enumerating + * devices with PPCD enabled. + */ + case 0x0d9d: + ehci_info(ehci, "disable lpm/ppcd for nvidia mcp89"); + ehci->has_lpm = 0; + ehci->has_ppcd = 0; + ehci->command &= ~CMD_PPCEE; + break; } break; case PCI_VENDOR_ID_VIA: -- cgit v1.2.1 From abf03184a31a3286fc0ab30f838ddee8ba9f9b7b Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 29 Nov 2010 10:17:22 -0500 Subject: USB: fix autosuspend bug in usb-serial This patch (as1437) fixes a bug in the usb-serial autosuspend handling. Since the usb-serial core now has autosuspend support, it must set the .supports_autosuspend member in every serial driver it registers. Otherwise the usb_autopm_get_interface() call won't work. This fixes Bugzilla #23012. Signed-off-by: Alan Stern CC: stable@kernel.org Reported-by: Kevin Smith Reported-and-tested-by: Simon Gerber Reported-and-tested-by: Matteo Croce Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/usb-serial.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 861223f2af6e..6954de50c0ff 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -51,6 +51,7 @@ static struct usb_driver usb_serial_driver = { .suspend = usb_serial_suspend, .resume = usb_serial_resume, .no_dynamic_id = 1, + .supports_autosuspend = 1, }; /* There is no MODULE_DEVICE_TABLE for usbserial.c. Instead @@ -1343,6 +1344,8 @@ int usb_serial_register(struct usb_serial_driver *driver) return -ENODEV; fixup_generic(driver); + if (driver->usb_driver) + driver->usb_driver->supports_autosuspend = 1; if (!driver->description) driver->description = driver->driver.name; -- cgit v1.2.1 From f8bbeabc34aa945ab4275abc9a4dfde0aea798ca Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Thu, 9 Dec 2010 10:29:00 -0800 Subject: xhci: Fix issue with port array setup and buggy hosts. Fix two bugs with the port array setup. The first bug will only show up with broken xHCI hosts with Extended Capabilities registers that have duplicate port speed entries for the same port. The idea with the original code was to set the port_array entry to -1 if the duplicate port speed entry said the port was a different speed than the original port speed entry. That would mean that later, the port would not be exposed to the USB core. Unfortunately, I forgot a continue statement, and the port_array entry would just be overwritten in the next line. The second bug would happen if there are conflicting port speed registers (so that some entry in port_array is -1), or one of the hardware port registers was not described in the port speed registers (so that some entry in port_array is 0). The code that sets up the usb2_ports array would accidentally claim those ports. That wouldn't really cause any user-visible issues, but it is a bug. This patch should go into the stable trees that have the port array and USB 3.0 port disabling prevention patches. Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci-mem.c | 25 +++++++++++++++---------- 1 file changed, 15 insertions(+), 10 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 0fae58ef8afe..1d0f45f0e7a6 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1680,6 +1680,7 @@ static void xhci_add_in_port(struct xhci_hcd *xhci, unsigned int num_ports, xhci->port_array[i] = (u8) -1; } /* FIXME: Should we disable the port? */ + continue; } xhci->port_array[i] = major_revision; if (major_revision == 0x03) @@ -1758,16 +1759,20 @@ static int xhci_setup_port_arrays(struct xhci_hcd *xhci, gfp_t flags) return -ENOMEM; port_index = 0; - for (i = 0; i < num_ports; i++) - if (xhci->port_array[i] != 0x03) { - xhci->usb2_ports[port_index] = - &xhci->op_regs->port_status_base + - NUM_PORT_REGS*i; - xhci_dbg(xhci, "USB 2.0 port at index %u, " - "addr = %p\n", i, - xhci->usb2_ports[port_index]); - port_index++; - } + for (i = 0; i < num_ports; i++) { + if (xhci->port_array[i] == 0x03 || + xhci->port_array[i] == 0 || + xhci->port_array[i] == -1) + continue; + + xhci->usb2_ports[port_index] = + &xhci->op_regs->port_status_base + + NUM_PORT_REGS*i; + xhci_dbg(xhci, "USB 2.0 port at index %u, " + "addr = %p\n", i, + xhci->usb2_ports[port_index]); + port_index++; + } } if (xhci->num_usb3_ports) { xhci->usb3_ports = kmalloc(sizeof(*xhci->usb3_ports)* -- cgit v1.2.1 From 5363cdc3c5da9bd431552cf5989ab481596f0c6d Mon Sep 17 00:00:00 2001 From: Florian Faber Date: Wed, 1 Dec 2010 10:11:08 +0100 Subject: USB: ftdi_sio: Add D.O.Tec PID Add FTDI PID to identify D.O.Tec devices correctly. Signed-off-by: Florian Faber Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio_ids.h | 5 +++++ 2 files changed, 6 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 6a50965e23f2..2dec50013528 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -796,6 +796,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LOGBOOKML_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LS_LOGBOOK_PID) }, { USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_HS_LOGBOOK_PID) }, + { USB_DEVICE(FTDI_VID, FTDI_DOTEC_PID) }, { USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { }, /* Optional parameter entry */ diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index 1286f1e23d8c..bf0867285481 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -1080,6 +1080,11 @@ #define MJSG_XM_RADIO_PID 0x937A #define MJSG_HD_RADIO_PID 0x937C +/* + * D.O.Tec products (http://www.directout.eu) + */ +#define FTDI_DOTEC_PID 0x9868 + /* * Xverve Signalyzer tools (http://www.signalyzer.com/) */ -- cgit v1.2.1 From f4ce9084476dc518bfd0f35f62f4bd0a130893e0 Mon Sep 17 00:00:00 2001 From: Pavankumar Kondeti Date: Thu, 16 Dec 2010 14:32:24 +0530 Subject: USB: core: Add input prompt and help text for USB_OTG config bd6882 commit (usb: gadget: fix Kconfig warning) removes the duplicate USB_OTG config from gadget/Kconfig. But does not copy the input prompt and help text to the original config defined in core/Kconfig. Add them now. Signed-off-by: Pavankumar Kondeti Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/Kconfig | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/core/Kconfig b/drivers/usb/core/Kconfig index 9eed5b52d9de..bcc24779ba0e 100644 --- a/drivers/usb/core/Kconfig +++ b/drivers/usb/core/Kconfig @@ -107,11 +107,19 @@ config USB_SUSPEND If you are unsure about this, say N here. config USB_OTG - bool + bool "OTG support" depends on USB && EXPERIMENTAL depends on USB_SUSPEND default n - + help + The most notable feature of USB OTG is support for a + "Dual-Role" device, which can act as either a device + or a host. The initial role is decided by the type of + plug inserted and can be changed later when two dual + role devices talk to each other. + + Select this only if your board has Mini-AB/Micro-AB + connector. config USB_OTG_WHITELIST bool "Rely on OTG Targeted Peripherals List" -- cgit v1.2.1 From daba58035a044cae75488175a96cc18362a64518 Mon Sep 17 00:00:00 2001 From: Pavankumar Kondeti Date: Thu, 16 Dec 2010 14:32:25 +0530 Subject: USB: gadget: Remove suspended sysfs file before freeing cdev cdev struct is accessed in suspended sysfs show function. So remove sysfs file before freeing the cdev in composite_unbind. Signed-off-by: Pavankumar Kondeti Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/composite.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c index 7b5cc16e4a0b..96413a240fdf 100644 --- a/drivers/usb/gadget/composite.c +++ b/drivers/usb/gadget/composite.c @@ -1047,9 +1047,9 @@ composite_unbind(struct usb_gadget *gadget) kfree(cdev->req->buf); usb_ep_free_request(gadget->ep0, cdev->req); } + device_remove_file(&gadget->dev, &dev_attr_suspended); kfree(cdev); set_gadget_data(gadget, NULL); - device_remove_file(&gadget->dev, &dev_attr_suspended); composite = NULL; } -- cgit v1.2.1 From d73a9b3001f29271c2e9f2a806b05a431c5d9591 Mon Sep 17 00:00:00 2001 From: Vitaly Kuznetsov Date: Tue, 14 Dec 2010 10:16:49 -0500 Subject: USB: usb-storage: unusual_devs entry for the Samsung YP-CP3 Add an unusual_devs entry for the Samsung YP-CP3 MP4 player. User was getting the following errors in dmesg: usb 2-6: reset high speed USB device using ehci_hcd and address 2 usb 2-6: reset high speed USB device using ehci_hcd and address 2 usb 2-6: reset high speed USB device using ehci_hcd and address 2 usb 2-6: USB disconnect, address 2 sd 3:0:0:0: [sdb] Assuming drive cache: write through sdb:<2>ldm_validate_partition_table(): Disk read failed. Dev sdb: unable to read RDB block 0 unable to read partition table Signed-off-by: Vitaly Kuznetsov Acked-by: Alan Stern CC: Matthew Dharm CC: stable@kernel.org Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers/usb') diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 6ccdd3dd5259..fcc1e32ce256 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -481,6 +481,13 @@ UNUSUAL_DEV( 0x04e8, 0x507c, 0x0220, 0x0220, USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_MAX_SECTORS_64), +/* Reported by Vitaly Kuznetsov */ +UNUSUAL_DEV( 0x04e8, 0x5122, 0x0000, 0x9999, + "Samsung", + "YP-CP3", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_MAX_SECTORS_64 | US_FL_BULK_IGNORE_TAG), + /* Entry and supporting patch by Theodore Kilgore . * Device uses standards-violating 32-byte Bulk Command Block Wrappers and * reports itself as "Proprietary SCSI Bulk." Cf. device entry 0x084d:0x0011. -- cgit v1.2.1 From ecc1624a2fff45780959efbcb73ace18fdb3c58d Mon Sep 17 00:00:00 2001 From: Thomas Sailer Date: Tue, 14 Dec 2010 16:04:05 +0100 Subject: USB: misc: uss720.c: add another vendor/product ID Fabio Battaglia report that he has another cable that works with this driver, so this patch adds its vendor/product ID. Signed-off-by: Thomas Sailer Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/uss720.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers/usb') diff --git a/drivers/usb/misc/uss720.c b/drivers/usb/misc/uss720.c index 796e2f68f749..4ff21587ab03 100644 --- a/drivers/usb/misc/uss720.c +++ b/drivers/usb/misc/uss720.c @@ -3,7 +3,7 @@ /* * uss720.c -- USS720 USB Parport Cable. * - * Copyright (C) 1999, 2005 + * Copyright (C) 1999, 2005, 2010 * Thomas Sailer (t.sailer@alumni.ethz.ch) * * This program is free software; you can redistribute it and/or modify @@ -776,6 +776,8 @@ static const struct usb_device_id uss720_table[] = { { USB_DEVICE(0x0557, 0x2001) }, { USB_DEVICE(0x0729, 0x1284) }, { USB_DEVICE(0x1293, 0x0002) }, + { USB_DEVICE(0x1293, 0x0002) }, + { USB_DEVICE(0x050d, 0x0002) }, { } /* Terminating entry */ }; -- cgit v1.2.1 From dbb442b85a1d82f91cfe0524c4f9b3a5196a10ca Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Thu, 16 Dec 2010 15:52:30 -0800 Subject: Revert "USB: gadget: Allow function access to device ID data during bind()" This reverts commit 1ab83238740ff1e1773d5c13ecac43c60cf4aec4. Turns out this doesn't allow for the device ids to be overridden properly, so we need to revert the thing. Reported-by: Jef Driesen Cc: Robert Lukassen Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/composite.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) (limited to 'drivers/usb') diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c index 96413a240fdf..8572dad5ecbb 100644 --- a/drivers/usb/gadget/composite.c +++ b/drivers/usb/gadget/composite.c @@ -1107,14 +1107,6 @@ static int composite_bind(struct usb_gadget *gadget) */ usb_ep_autoconfig_reset(cdev->gadget); - /* standardized runtime overrides for device ID data */ - if (idVendor) - cdev->desc.idVendor = cpu_to_le16(idVendor); - if (idProduct) - cdev->desc.idProduct = cpu_to_le16(idProduct); - if (bcdDevice) - cdev->desc.bcdDevice = cpu_to_le16(bcdDevice); - /* composite gadget needs to assign strings for whole device (like * serial number), register function drivers, potentially update * power state and consumption, etc @@ -1126,6 +1118,14 @@ static int composite_bind(struct usb_gadget *gadget) cdev->desc = *composite->dev; cdev->desc.bMaxPacketSize0 = gadget->ep0->maxpacket; + /* standardized runtime overrides for device ID data */ + if (idVendor) + cdev->desc.idVendor = cpu_to_le16(idVendor); + if (idProduct) + cdev->desc.idProduct = cpu_to_le16(idProduct); + if (bcdDevice) + cdev->desc.bcdDevice = cpu_to_le16(bcdDevice); + /* stirng overrides */ if (iManufacturer || !cdev->desc.iManufacturer) { if (!iManufacturer && !composite->iManufacturer && -- cgit v1.2.1