From ce8cb803d8b90458495f23606c706f0c0c857cdc Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 12 Aug 2016 18:40:23 +0200 Subject: i2c: mux: demux-pinctrl: properly roll back when adding adapter fails We also need to revert the dynamic OF change, so we get a consistent state again. Otherwise, we might have two devices enabled e.g. after pinctrl setup fails. Signed-off-by: Wolfram Sang Signed-off-by: Wolfram Sang Cc: stable@kernel.org --- drivers/i2c/muxes/i2c-demux-pinctrl.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/muxes/i2c-demux-pinctrl.c b/drivers/i2c/muxes/i2c-demux-pinctrl.c index 8de073aed001..215ac87f606d 100644 --- a/drivers/i2c/muxes/i2c-demux-pinctrl.c +++ b/drivers/i2c/muxes/i2c-demux-pinctrl.c @@ -68,7 +68,7 @@ static int i2c_demux_activate_master(struct i2c_demux_pinctrl_priv *priv, u32 ne adap = of_find_i2c_adapter_by_node(priv->chan[new_chan].parent_np); if (!adap) { ret = -ENODEV; - goto err; + goto err_with_revert; } p = devm_pinctrl_get_select(adap->dev.parent, priv->bus_name); @@ -103,6 +103,8 @@ static int i2c_demux_activate_master(struct i2c_demux_pinctrl_priv *priv, u32 ne err_with_put: i2c_put_adapter(adap); + err_with_revert: + of_changeset_revert(&priv->chan[new_chan].chgset); err: dev_err(priv->dev, "failed to setup demux-adapter %d (%d)\n", new_chan, ret); return ret; -- cgit v1.2.3 From 4d01d88019261d05ec3bff5f1a6013393faa3b9e Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Wed, 10 Aug 2016 13:37:18 -0700 Subject: i2c: cros-ec-tunnel: Fix usage of cros_ec_cmd_xfer() cros_ec_cmd_xfer returns success status if the command transport completes successfully, but the execution result is incorrectly ignored. In many cases, the execution result is assumed to be successful, leading to ignored errors and operating on uninitialized data. We've recently introduced the cros_ec_cmd_xfer_status() helper to avoid these problems. Let's use it. [Regarding the 'Fixes' tag; there is significant refactoring since the driver's introduction, but the underlying logical error exists throughout I believe] Fixes: 9d230c9e4f4e ("i2c: ChromeOS EC tunnel driver") Cc: # 9798ac6d32c1 mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper Signed-off-by: Brian Norris Reviewed-by: Javier Martinez Canillas Reviewed-by: Guenter Roeck Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-cros-ec-tunnel.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-cros-ec-tunnel.c b/drivers/i2c/busses/i2c-cros-ec-tunnel.c index a0d95ff682ae..2d5ff86398d0 100644 --- a/drivers/i2c/busses/i2c-cros-ec-tunnel.c +++ b/drivers/i2c/busses/i2c-cros-ec-tunnel.c @@ -215,7 +215,7 @@ static int ec_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg i2c_msgs[], msg->outsize = request_len; msg->insize = response_len; - result = cros_ec_cmd_xfer(bus->ec, msg); + result = cros_ec_cmd_xfer_status(bus->ec, msg); if (result < 0) { dev_err(dev, "Error transferring EC i2c message %d\n", result); goto exit; -- cgit v1.2.3 From 97ccd4af120c6ee183f424f17672870809bd6efd Mon Sep 17 00:00:00 2001 From: Alexey Khoroshilov Date: Thu, 4 Aug 2016 02:38:44 +0300 Subject: i2c: ocores: add missed clk_disable_unprepare() on failure paths clk_disable_unprepare() is missed on failure paths in ocores_i2c_probe(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov Acked-by: Peter Korsgaard Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-ocores.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c index dfa7a4b4a91d..ac88a524143e 100644 --- a/drivers/i2c/busses/i2c-ocores.c +++ b/drivers/i2c/busses/i2c-ocores.c @@ -379,6 +379,7 @@ static int ocores_i2c_of_probe(struct platform_device *pdev, if (!clock_frequency_present) { dev_err(&pdev->dev, "Missing required parameter 'opencores,ip-clock-frequency'\n"); + clk_disable_unprepare(i2c->clk); return -ENODEV; } i2c->ip_clock_khz = clock_frequency / 1000; @@ -467,20 +468,21 @@ static int ocores_i2c_probe(struct platform_device *pdev) default: dev_err(&pdev->dev, "Unsupported I/O width (%d)\n", i2c->reg_io_width); - return -EINVAL; + ret = -EINVAL; + goto err_clk; } } ret = ocores_init(&pdev->dev, i2c); if (ret) - return ret; + goto err_clk; init_waitqueue_head(&i2c->wait); ret = devm_request_irq(&pdev->dev, irq, ocores_isr, 0, pdev->name, i2c); if (ret) { dev_err(&pdev->dev, "Cannot claim IRQ\n"); - return ret; + goto err_clk; } /* hook up driver to tree */ @@ -494,7 +496,7 @@ static int ocores_i2c_probe(struct platform_device *pdev) ret = i2c_add_adapter(&i2c->adap); if (ret) { dev_err(&pdev->dev, "Failed to add adapter\n"); - return ret; + goto err_clk; } /* add in known devices to the bus */ @@ -504,6 +506,10 @@ static int ocores_i2c_probe(struct platform_device *pdev) } return 0; + +err_clk: + clk_disable_unprepare(i2c->clk); + return ret; } static int ocores_i2c_remove(struct platform_device *pdev) -- cgit v1.2.3 From 434f14e745442a4230a40cf47f84deac1028f64f Mon Sep 17 00:00:00 2001 From: Cyrille Pitchen Date: Wed, 3 Aug 2016 16:58:26 +0200 Subject: i2c: at91: fix support of the "alternative command" feature The "alternative command" feature was introduced with sama5d2 SoCs. Its purpose is to let the hardware i2c controller automatically send the STOP condition on the i2c bus at the end of a data transfer. Without this feature, the i2c driver has to write the 'STOP' bit into the Control Register so the hardware i2c controller is triggered to send the STOP condition on the bus. Using the "alternative command" feature requires to set the transfer data length into the 8bit DATAL field of the Alternative Command Register. Hence only data transfers up to 255 bytes can take advantage of the "alternative command" feature. For greater data transfer sizes, the driver should use the previous implementation, when the "alternative command" support was not implemented yet. Signed-off-by: Cyrille Pitchen Signed-off-by: Ludovic Desroches Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-at91.c | 24 ++++++++++++++---------- 1 file changed, 14 insertions(+), 10 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c index f23372669f77..1bb97f658b47 100644 --- a/drivers/i2c/busses/i2c-at91.c +++ b/drivers/i2c/busses/i2c-at91.c @@ -38,6 +38,7 @@ #define AT91_I2C_TIMEOUT msecs_to_jiffies(100) /* transfer timeout */ #define AT91_I2C_DMA_THRESHOLD 8 /* enable DMA if transfer size is bigger than this threshold */ #define AUTOSUSPEND_TIMEOUT 2000 +#define AT91_I2C_MAX_ALT_CMD_DATA_SIZE 256 /* AT91 TWI register definitions */ #define AT91_TWI_CR 0x0000 /* Control Register */ @@ -141,6 +142,7 @@ struct at91_twi_dev { unsigned twi_cwgr_reg; struct at91_twi_pdata *pdata; bool use_dma; + bool use_alt_cmd; bool recv_len_abort; u32 fifo_size; struct at91_twi_dma dma; @@ -269,7 +271,7 @@ static void at91_twi_write_next_byte(struct at91_twi_dev *dev) /* send stop when last byte has been written */ if (--dev->buf_len == 0) - if (!dev->pdata->has_alt_cmd) + if (!dev->use_alt_cmd) at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP); dev_dbg(dev->dev, "wrote 0x%x, to go %d\n", *dev->buf, dev->buf_len); @@ -292,7 +294,7 @@ static void at91_twi_write_data_dma_callback(void *data) * we just have to enable TXCOMP one. */ at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); - if (!dev->pdata->has_alt_cmd) + if (!dev->use_alt_cmd) at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP); } @@ -410,7 +412,7 @@ static void at91_twi_read_next_byte(struct at91_twi_dev *dev) } /* send stop if second but last byte has been read */ - if (!dev->pdata->has_alt_cmd && dev->buf_len == 1) + if (!dev->use_alt_cmd && dev->buf_len == 1) at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP); dev_dbg(dev->dev, "read 0x%x, to go %d\n", *dev->buf, dev->buf_len); @@ -426,7 +428,7 @@ static void at91_twi_read_data_dma_callback(void *data) dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg[0]), dev->buf_len, DMA_FROM_DEVICE); - if (!dev->pdata->has_alt_cmd) { + if (!dev->use_alt_cmd) { /* The last two bytes have to be read without using dma */ dev->buf += dev->buf_len - 2; dev->buf_len = 2; @@ -443,7 +445,7 @@ static void at91_twi_read_data_dma(struct at91_twi_dev *dev) struct dma_chan *chan_rx = dma->chan_rx; size_t buf_len; - buf_len = (dev->pdata->has_alt_cmd) ? dev->buf_len : dev->buf_len - 2; + buf_len = (dev->use_alt_cmd) ? dev->buf_len : dev->buf_len - 2; dma->direction = DMA_FROM_DEVICE; /* Keep in mind that we won't use dma to read the last two bytes */ @@ -651,7 +653,7 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev) unsigned start_flags = AT91_TWI_START; /* if only one byte is to be read, immediately stop transfer */ - if (!has_alt_cmd && dev->buf_len <= 1 && + if (!dev->use_alt_cmd && dev->buf_len <= 1 && !(dev->msg->flags & I2C_M_RECV_LEN)) start_flags |= AT91_TWI_STOP; at91_twi_write(dev, AT91_TWI_CR, start_flags); @@ -745,7 +747,7 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num) int ret; unsigned int_addr_flag = 0; struct i2c_msg *m_start = msg; - bool is_read, use_alt_cmd = false; + bool is_read; dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num); @@ -768,14 +770,16 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num) at91_twi_write(dev, AT91_TWI_IADR, internal_address); } + dev->use_alt_cmd = false; is_read = (m_start->flags & I2C_M_RD); if (dev->pdata->has_alt_cmd) { - if (m_start->len > 0) { + if (m_start->len > 0 && + m_start->len < AT91_I2C_MAX_ALT_CMD_DATA_SIZE) { at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_ACMEN); at91_twi_write(dev, AT91_TWI_ACR, AT91_TWI_ACR_DATAL(m_start->len) | ((is_read) ? AT91_TWI_ACR_DIR : 0)); - use_alt_cmd = true; + dev->use_alt_cmd = true; } else { at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_ACMDIS); } @@ -784,7 +788,7 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num) at91_twi_write(dev, AT91_TWI_MMR, (m_start->addr << 16) | int_addr_flag | - ((!use_alt_cmd && is_read) ? AT91_TWI_MREAD : 0)); + ((!dev->use_alt_cmd && is_read) ? AT91_TWI_MREAD : 0)); dev->buf_len = m_start->len; dev->buf = m_start->buf; -- cgit v1.2.3 From 8d263be8716da67bd8746e266c1934cb9c9933cc Mon Sep 17 00:00:00 2001 From: Daniel Wagner Date: Wed, 3 Aug 2016 14:03:08 +0200 Subject: i2c: bcm-iproc: Use complete() instead of complete_all() There is only one waiter for the completion, therefore there is no need to use complete_all(). Let's make that clear by using complete() instead of complete_all(). The usage pattern of the completion is: bcm_iproc_i2c_xfer_single_msg() reinit_completion() ... (activate the transfer) ... wait_for_completion_timeout() Signed-off-by: Daniel Wagner Acked-by: Ray Jui Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-bcm-iproc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c index 19c843828fe2..95f7cac76f89 100644 --- a/drivers/i2c/busses/i2c-bcm-iproc.c +++ b/drivers/i2c/busses/i2c-bcm-iproc.c @@ -158,7 +158,7 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data) if (status & BIT(IS_M_START_BUSY_SHIFT)) { iproc_i2c->xfer_is_done = 1; - complete_all(&iproc_i2c->done); + complete(&iproc_i2c->done); } writel(status, iproc_i2c->base + IS_OFFSET); -- cgit v1.2.3 From 752c3899f97c469efea42b1ad6de66d18a21ce09 Mon Sep 17 00:00:00 2001 From: Daniel Wagner Date: Wed, 3 Aug 2016 14:03:09 +0200 Subject: i2c: bcm-kona: Use complete() instead of complete_all() There is only one waiter for the completion, therefore there is no need to use complete_all(). Let's make that clear by using complete() instead of complete_all(). The usage pattern of the completion is: bcm_kona_send_i2c_cmd() reinit_completion() ... bcm_kona_i2c_send_cmd_to_ctrl() ... wait_for_completion_timeout() Signed-off-by: Daniel Wagner Acked-by: Ray Jui Reviewed-by: Tim Kryger Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-bcm-kona.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-bcm-kona.c b/drivers/i2c/busses/i2c-bcm-kona.c index ac9f47679c3a..f98743277e3c 100644 --- a/drivers/i2c/busses/i2c-bcm-kona.c +++ b/drivers/i2c/busses/i2c-bcm-kona.c @@ -229,7 +229,7 @@ static irqreturn_t bcm_kona_i2c_isr(int irq, void *devid) dev->base + TXFCR_OFFSET); writel(status & ~ISR_RESERVED_MASK, dev->base + ISR_OFFSET); - complete_all(&dev->done); + complete(&dev->done); return IRQ_HANDLED; } -- cgit v1.2.3 From fea03a6ab1d8e456c0319c194150621629504f80 Mon Sep 17 00:00:00 2001 From: Daniel Wagner Date: Wed, 3 Aug 2016 14:03:10 +0200 Subject: i2c: brcmstb: Use complete() instead of complete_all() There is only one waiter for the completion, therefore there is no need to use complete_all(). Let's make that clear by using complete() instead of complete_all(). The usage pattern of the completion is: brcmstb_send_i2c_cmd() reinit_completion() ... /* initiate transfer by setting iic_enable */ ... brcmstb_i2c_wait_for_completion() Signed-off-by: Daniel Wagner Reviewed-by: Kamal Dasu Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-brcmstb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-brcmstb.c b/drivers/i2c/busses/i2c-brcmstb.c index 3f5a4d71d3bf..385b57bfcb38 100644 --- a/drivers/i2c/busses/i2c-brcmstb.c +++ b/drivers/i2c/busses/i2c-brcmstb.c @@ -228,7 +228,7 @@ static irqreturn_t brcmstb_i2c_isr(int irq, void *devid) return IRQ_NONE; brcmstb_i2c_enable_disable_irq(dev, INT_DISABLE); - complete_all(&dev->done); + complete(&dev->done); dev_dbg(dev->device, "isr handled"); return IRQ_HANDLED; -- cgit v1.2.3 From 0268263f0cf2239eb3a747936d8d36ef5f5e1688 Mon Sep 17 00:00:00 2001 From: Daniel Wagner Date: Wed, 3 Aug 2016 14:03:11 +0200 Subject: i2c: meson: Use complete() instead of complete_all() There is only one waiter for the completion, therefore there is no need to use complete_all(). Let's make that clear by using complete() instead of complete_all(). The usage pattern of the completion is: meson_i2c_xfer_msg() reinit_completion() ... /* Start the transfer */ ... wait_for_completion_timeout() Signed-off-by: Daniel Wagner Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-meson.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-meson.c b/drivers/i2c/busses/i2c-meson.c index 71d3929adf54..76e28980904f 100644 --- a/drivers/i2c/busses/i2c-meson.c +++ b/drivers/i2c/busses/i2c-meson.c @@ -211,7 +211,7 @@ static void meson_i2c_stop(struct meson_i2c *i2c) meson_i2c_add_token(i2c, TOKEN_STOP); } else { i2c->state = STATE_IDLE; - complete_all(&i2c->done); + complete(&i2c->done); } } @@ -238,7 +238,7 @@ static irqreturn_t meson_i2c_irq(int irqno, void *dev_id) dev_dbg(i2c->dev, "error bit set\n"); i2c->error = -ENXIO; i2c->state = STATE_IDLE; - complete_all(&i2c->done); + complete(&i2c->done); goto out; } @@ -269,7 +269,7 @@ static irqreturn_t meson_i2c_irq(int irqno, void *dev_id) break; case STATE_STOP: i2c->state = STATE_IDLE; - complete_all(&i2c->done); + complete(&i2c->done); break; case STATE_IDLE: break; -- cgit v1.2.3 From 9a5382e8ffe86412f442f6a34fde43f94aae530b Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 22 Aug 2016 16:52:21 +0200 Subject: i2c: mux: demux-pinctrl: invalidate properly when switching fails Make sure the index to the active channel is invalidated when switching fails. Signed-off-by: Wolfram Sang Signed-off-by: Wolfram Sang --- drivers/i2c/muxes/i2c-demux-pinctrl.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/i2c') diff --git a/drivers/i2c/muxes/i2c-demux-pinctrl.c b/drivers/i2c/muxes/i2c-demux-pinctrl.c index 215ac87f606d..b6b9d2582fac 100644 --- a/drivers/i2c/muxes/i2c-demux-pinctrl.c +++ b/drivers/i2c/muxes/i2c-demux-pinctrl.c @@ -107,6 +107,7 @@ static int i2c_demux_activate_master(struct i2c_demux_pinctrl_priv *priv, u32 ne of_changeset_revert(&priv->chan[new_chan].chgset); err: dev_err(priv->dev, "failed to setup demux-adapter %d (%d)\n", new_chan, ret); + priv->cur_chan = -EINVAL; return ret; } -- cgit v1.2.3 From 488d69ea72457c7566b36eb0d484d579f19963c5 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Wed, 24 Aug 2016 11:19:28 +0200 Subject: i2c: sh_mobile: use proper device with dma_mapping_error We must use the same device we used for mapping. Signed-off-by: Wolfram Sang Reviewed-by: Geert Uytterhoeven Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-sh_mobile.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index 6fb3e2645992..05b1eeab9cf5 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -610,7 +610,7 @@ static void sh_mobile_i2c_xfer_dma(struct sh_mobile_i2c_data *pd) return; dma_addr = dma_map_single(chan->device->dev, pd->msg->buf, pd->msg->len, dir); - if (dma_mapping_error(pd->dev, dma_addr)) { + if (dma_mapping_error(chan->device->dev, dma_addr)) { dev_dbg(pd->dev, "dma map failed, using PIO\n"); return; } -- cgit v1.2.3 From c13c29186c59b056d6ec141b5967c2ca3efc0c16 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Wed, 24 Aug 2016 11:19:29 +0200 Subject: i2c: rcar: use proper device with dma_mapping_error We must use the same device we used for mapping. Signed-off-by: Wolfram Sang Reviewed-by: Geert Uytterhoeven Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-rcar.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-rcar.c b/drivers/i2c/busses/i2c-rcar.c index 52407f3c9e1c..9bd849dacee8 100644 --- a/drivers/i2c/busses/i2c-rcar.c +++ b/drivers/i2c/busses/i2c-rcar.c @@ -378,7 +378,7 @@ static void rcar_i2c_dma(struct rcar_i2c_priv *priv) } dma_addr = dma_map_single(chan->device->dev, buf, len, dir); - if (dma_mapping_error(dev, dma_addr)) { + if (dma_mapping_error(chan->device->dev, dma_addr)) { dev_dbg(dev, "dma map failed, using PIO\n"); return; } -- cgit v1.2.3 From b31cc4b37e8e33e84e9f990d0d84387f37ef01a1 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 15 Aug 2016 00:47:22 +0200 Subject: i2c: bcm-kona: fix inconsistent indenting smatch rightfully says: drivers/i2c/busses/i2c-bcm-kona.c:646 bcm_kona_i2c_xfer() warn: inconsistent indenting Signed-off-by: Wolfram Sang Reviewed-by: Tim Kryger --- drivers/i2c/busses/i2c-bcm-kona.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-bcm-kona.c b/drivers/i2c/busses/i2c-bcm-kona.c index f98743277e3c..258cb9a40ab3 100644 --- a/drivers/i2c/busses/i2c-bcm-kona.c +++ b/drivers/i2c/busses/i2c-bcm-kona.c @@ -643,7 +643,7 @@ static int bcm_kona_i2c_xfer(struct i2c_adapter *adapter, if (rc < 0) { dev_err(dev->device, "restart cmd failed rc = %d\n", rc); - goto xfer_send_stop; + goto xfer_send_stop; } } -- cgit v1.2.3 From e35478eac030990e23a56bf11dc074c5a069124a Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 23 Aug 2016 17:28:03 +0200 Subject: i2c: mux: demux-pinctrl: run properly with multiple instances We can't use a static property for all the changesets, so we now create dynamic ones for each changeset. Signed-off-by: Wolfram Sang Fixes: 50a5ba87690814 ("i2c: mux: demux-pinctrl: add driver") Signed-off-by: Wolfram Sang --- drivers/i2c/muxes/i2c-demux-pinctrl.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/muxes/i2c-demux-pinctrl.c b/drivers/i2c/muxes/i2c-demux-pinctrl.c index b6b9d2582fac..b3893f6282ba 100644 --- a/drivers/i2c/muxes/i2c-demux-pinctrl.c +++ b/drivers/i2c/muxes/i2c-demux-pinctrl.c @@ -37,8 +37,6 @@ struct i2c_demux_pinctrl_priv { struct i2c_demux_pinctrl_chan chan[]; }; -static struct property status_okay = { .name = "status", .length = 3, .value = "ok" }; - static int i2c_demux_master_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) { struct i2c_demux_pinctrl_priv *priv = adap->algo_data; @@ -193,6 +191,7 @@ static int i2c_demux_pinctrl_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; struct i2c_demux_pinctrl_priv *priv; + struct property *props; int num_chan, i, j, err; num_chan = of_count_phandle_with_args(np, "i2c-parent", NULL); @@ -203,7 +202,10 @@ static int i2c_demux_pinctrl_probe(struct platform_device *pdev) priv = devm_kzalloc(&pdev->dev, sizeof(*priv) + num_chan * sizeof(struct i2c_demux_pinctrl_chan), GFP_KERNEL); - if (!priv) + + props = devm_kcalloc(&pdev->dev, num_chan, sizeof(*props), GFP_KERNEL); + + if (!priv || !props) return -ENOMEM; err = of_property_read_string(np, "i2c-bus-name", &priv->bus_name); @@ -221,8 +223,12 @@ static int i2c_demux_pinctrl_probe(struct platform_device *pdev) } priv->chan[i].parent_np = adap_np; + props[i].name = devm_kstrdup(&pdev->dev, "status", GFP_KERNEL); + props[i].value = devm_kstrdup(&pdev->dev, "ok", GFP_KERNEL); + props[i].length = 3; + of_changeset_init(&priv->chan[i].chgset); - of_changeset_update_property(&priv->chan[i].chgset, adap_np, &status_okay); + of_changeset_update_property(&priv->chan[i].chgset, adap_np, &props[i]); } priv->num_chan = num_chan; -- cgit v1.2.3 From 664d58bf4d3406dc4404e29bcb8c89fd22589d57 Mon Sep 17 00:00:00 2001 From: Zhuo-hao Lee Date: Sat, 27 Aug 2016 15:39:30 +0800 Subject: i2c: designware: save the preset value of DW_IC_SDA_HOLD There are several ways to set the SDA hold time for i2c controller, including: Device Tree, built-in device properties and ACPI. However, if the SDA hold time is not specified by above method, we should read the value, where it is preset by firmware, and save it to sda_hold_time. This is needed because when i2c controller enters runtime suspend, the DW_IC_SDA_HOLD value will be reset to chipset default value. And during runtime resume, i2c_dw_init will be called to reconfigure i2c controller. If sda_hold_time is zero, the chipset default hold time will be used, that will be too short for some platforms. Therefore, to have a better tolerance, the DW_IC_SDA_HOLD value should be kept by sda_hold_time. Signed-off-by: Zhuo-hao Lee Reviewed-by: Andy Shevchenko Acked-by: Jarkko Nikula Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-core.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index c6922b806fb7..fcd973d5131e 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -367,13 +367,17 @@ int i2c_dw_init(struct dw_i2c_dev *dev) dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt); /* Configure SDA Hold Time if required */ - if (dev->sda_hold_time) { - reg = dw_readl(dev, DW_IC_COMP_VERSION); - if (reg >= DW_IC_SDA_HOLD_MIN_VERS) + reg = dw_readl(dev, DW_IC_COMP_VERSION); + if (reg >= DW_IC_SDA_HOLD_MIN_VERS) { + if (dev->sda_hold_time) { dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD); - else - dev_warn(dev->dev, - "Hardware too old to adjust SDA hold time."); + } else { + /* Keep previous hold time setting if no one set it */ + dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD); + } + } else { + dev_warn(dev->dev, + "Hardware too old to adjust SDA hold time.\n"); } /* Configure Tx/Rx FIFO threshold levels */ -- cgit v1.2.3 From e0603c8dd298171bd64227c65c6bbd6a861e1a78 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Wed, 31 Aug 2016 11:38:48 +0200 Subject: i2c: Spelling s/acknowedge/acknowledge/ Signed-off-by: Geert Uytterhoeven Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-cadence.c | 2 +- drivers/i2c/busses/i2c-rk3x.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-cadence.c b/drivers/i2c/busses/i2c-cadence.c index 90bbd9f9dd8f..3c16a2f7c673 100644 --- a/drivers/i2c/busses/i2c-cadence.c +++ b/drivers/i2c/busses/i2c-cadence.c @@ -767,7 +767,7 @@ static int cdns_i2c_setclk(unsigned long clk_in, struct cdns_i2c *id) * depending on the scaling direction. * * Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK - * to acknowedge the change, NOTIFY_DONE if the notification is + * to acknowledge the change, NOTIFY_DONE if the notification is * considered irrelevant. */ static int cdns_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c index 2bc8b01153d6..dce1abd43c7f 100644 --- a/drivers/i2c/busses/i2c-rk3x.c +++ b/drivers/i2c/busses/i2c-rk3x.c @@ -918,7 +918,7 @@ static void rk3x_i2c_adapt_div(struct rk3x_i2c *i2c, unsigned long clk_rate) * Code adapted from i2c-cadence.c. * * Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK - * to acknowedge the change, NOTIFY_DONE if the notification is + * to acknowledge the change, NOTIFY_DONE if the notification is * considered irrelevant. */ static int rk3x_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long -- cgit v1.2.3 From cbfff439c54f37fc363b1d365183fa61af43585c Mon Sep 17 00:00:00 2001 From: Doug Anderson Date: Mon, 29 Aug 2016 14:22:36 -0700 Subject: i2c: rk3x: Restore clock settings at resume time Depending on a number of factors including: - Which exact Rockchip SoC we're working with - How deep we suspend - Which i2c port we're on We might lose the state of the i2c registers at suspend time. Specifically we've found that on rk3399 the i2c ports that are not in the PMU power domain lose their state with the current suspend depth configured by ARM Tursted Firmware. Note that there are very few actual i2c registers that aren't configured per transfer anyway so all we actually need to re-configure are the clock config registers. We'll just add a call to rk3x_i2c_adapt_div() at resume time and be done with it. NOTE: On rk3399 on ports whose power was lost, I put printouts in at resume time. I saw things like: before: con=0x00010300, div=0x00060006 after: con=0x00010200, div=0x00180025 Signed-off-by: Douglas Anderson Reviewed-by: David Wu Tested-by: David Wu [wsa: removed duplicate const] Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-rk3x.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c index dce1abd43c7f..5c5b7cada8be 100644 --- a/drivers/i2c/busses/i2c-rk3x.c +++ b/drivers/i2c/busses/i2c-rk3x.c @@ -1111,6 +1111,15 @@ static int rk3x_i2c_xfer(struct i2c_adapter *adap, return ret < 0 ? ret : num; } +static __maybe_unused int rk3x_i2c_resume(struct device *dev) +{ + struct rk3x_i2c *i2c = dev_get_drvdata(dev); + + rk3x_i2c_adapt_div(i2c, clk_get_rate(i2c->clk)); + + return 0; +} + static u32 rk3x_i2c_func(struct i2c_adapter *adap) { return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING; @@ -1334,12 +1343,15 @@ static int rk3x_i2c_remove(struct platform_device *pdev) return 0; } +static SIMPLE_DEV_PM_OPS(rk3x_i2c_pm_ops, NULL, rk3x_i2c_resume); + static struct platform_driver rk3x_i2c_driver = { .probe = rk3x_i2c_probe, .remove = rk3x_i2c_remove, .driver = { .name = "rk3x-i2c", .of_match_table = rk3x_i2c_match, + .pm = &rk3x_i2c_pm_ops, }, }; -- cgit v1.2.3 From 371a015344b6e270e7e3632107d9554ec6d27a6b Mon Sep 17 00:00:00 2001 From: "Yadi.hu" Date: Sun, 18 Sep 2016 18:52:31 +0800 Subject: i2c-eg20t: fix race between i2c init and interrupt enable the eg20t driver call request_irq() function before the pch_base_address, base address of i2c controller's register, is assigned an effective value. there is one possible scenario that an interrupt which isn't inside eg20t arrives immediately after request_irq() is executed when i2c controller shares an interrupt number with others. since the interrupt handler pch_i2c_handler() has already active as shared action, it will be called and read its own register to determine if this interrupt is from itself. At that moment, since base address of i2c registers is not remapped in kernel space yet,so the INT handler will access an illegal address and then a error occurs. Signed-off-by: Yadi.hu Signed-off-by: Wolfram Sang Cc: stable@kernel.org --- drivers/i2c/busses/i2c-eg20t.c | 18 +++++++++++------- 1 file changed, 11 insertions(+), 7 deletions(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index 137125b5eae7..5ce71ce7b6c4 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -773,13 +773,6 @@ static int pch_i2c_probe(struct pci_dev *pdev, /* Set the number of I2C channel instance */ adap_info->ch_num = id->driver_data; - ret = request_irq(pdev->irq, pch_i2c_handler, IRQF_SHARED, - KBUILD_MODNAME, adap_info); - if (ret) { - pch_pci_err(pdev, "request_irq FAILED\n"); - goto err_request_irq; - } - for (i = 0; i < adap_info->ch_num; i++) { pch_adap = &adap_info->pch_data[i].pch_adapter; adap_info->pch_i2c_suspended = false; @@ -797,6 +790,17 @@ static int pch_i2c_probe(struct pci_dev *pdev, pch_adap->dev.of_node = pdev->dev.of_node; pch_adap->dev.parent = &pdev->dev; + } + + ret = request_irq(pdev->irq, pch_i2c_handler, IRQF_SHARED, + KBUILD_MODNAME, adap_info); + if (ret) { + pch_pci_err(pdev, "request_irq FAILED\n"); + goto err_request_irq; + } + + for (i = 0; i < adap_info->ch_num; i++) { + pch_adap = &adap_info->pch_data[i].pch_adapter; pch_i2c_init(&adap_info->pch_data[i]); -- cgit v1.2.3 From 463e8f845cbf1c01e4cc8aeef1703212991d8e1e Mon Sep 17 00:00:00 2001 From: Peter Rosin Date: Wed, 14 Sep 2016 15:24:12 +0200 Subject: i2c: mux: pca954x: retry updating the mux selection on failure The cached value of the last selected channel prevents retries on the next call, even on failure to update the selected channel. Fix that. Signed-off-by: Peter Rosin Signed-off-by: Wolfram Sang Cc: stable@kernel.org --- drivers/i2c/muxes/i2c-mux-pca954x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c index 528e755c468f..3278ebf1cc5c 100644 --- a/drivers/i2c/muxes/i2c-mux-pca954x.c +++ b/drivers/i2c/muxes/i2c-mux-pca954x.c @@ -164,7 +164,7 @@ static int pca954x_select_chan(struct i2c_mux_core *muxc, u32 chan) /* Only select the channel if its different from the last channel */ if (data->last_chan != regval) { ret = pca954x_reg_write(muxc->parent, client, regval); - data->last_chan = regval; + data->last_chan = ret ? 0 : regval; } return ret; -- cgit v1.2.3 From 331dcf421c34d227784d07943eb01e4023a42b0a Mon Sep 17 00:00:00 2001 From: Sudeep Holla Date: Thu, 25 Aug 2016 12:23:39 +0100 Subject: i2c: qup: skip qup_i2c_suspend if the device is already runtime suspended If the i2c device is already runtime suspended, if qup_i2c_suspend is executed during suspend-to-idle or suspend-to-ram it will result in the following splat: WARNING: CPU: 3 PID: 1593 at drivers/clk/clk.c:476 clk_core_unprepare+0x80/0x90 Modules linked in: CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14 Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT) PC is at clk_core_unprepare+0x80/0x90 LR is at clk_unprepare+0x28/0x40 pc : [] lr : [] pstate: 60000145 Call trace: clk_core_unprepare+0x80/0x90 qup_i2c_disable_clocks+0x2c/0x68 qup_i2c_suspend+0x10/0x20 platform_pm_suspend+0x24/0x68 ... This patch fixes the issue by executing qup_i2c_pm_suspend_runtime conditionally in qup_i2c_suspend. Signed-off-by: Sudeep Holla Reviewed-by: Andy Gross Signed-off-by: Wolfram Sang Cc: stable@kernel.org --- drivers/i2c/busses/i2c-qup.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/i2c') diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c index 501bd15cb78e..a8497cfdae6f 100644 --- a/drivers/i2c/busses/i2c-qup.c +++ b/drivers/i2c/busses/i2c-qup.c @@ -1599,7 +1599,8 @@ static int qup_i2c_pm_resume_runtime(struct device *device) #ifdef CONFIG_PM_SLEEP static int qup_i2c_suspend(struct device *device) { - qup_i2c_pm_suspend_runtime(device); + if (!pm_runtime_suspended(device)) + return qup_i2c_pm_suspend_runtime(device); return 0; } -- cgit v1.2.3