From fd9abb3d97c2ab883e4732ec1214fe64190236e7 Mon Sep 17 00:00:00 2001 From: Steve Glendinning Date: Wed, 5 Nov 2008 00:35:37 +0000 Subject: SMSC LAN911x and LAN921x vendor driver Attached is a driver for SMSC's LAN911x and LAN921x families of embedded ethernet controllers. There is an existing smc911x driver in the tree; this is intended to replace it. Dustin McIntire (the author of the smc911x driver) has expressed his support for switching to this driver. This driver contains workarounds for all known hardware issues, and has been tested on all flavours of the chip on multiple architectures. This driver now uses phylib, so this patch also adds support for the device's internal phy Signed-off-by: Steve Glendinning Signed-off-by: Bahadir Balban Signed-off-by: Dustin Mcintire Signed-off-by: Bill Gatliff Signed-off-by: Jeff Garzik --- MAINTAINERS | 6 + drivers/net/Kconfig | 14 + drivers/net/Makefile | 1 + drivers/net/phy/smsc.c | 28 + drivers/net/smsc911x.c | 2091 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/smsc911x.h | 394 +++++++++ include/linux/smsc911x.h | 42 + 7 files changed, 2576 insertions(+) create mode 100644 drivers/net/smsc911x.c create mode 100644 drivers/net/smsc911x.h create mode 100644 include/linux/smsc911x.h diff --git a/MAINTAINERS b/MAINTAINERS index 129117fe6490..5d951f3db018 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3853,6 +3853,12 @@ M: mhoffman@lightlink.com L: lm-sensors@lm-sensors.org S: Maintained +SMSC911x ETHERNET DRIVER +P: Steve Glendinning +M: steve.glendinning@smsc.com +L: netdev@vger.kernel.org +S: Supported + SMX UIO Interface P: Ben Nizette M: bn@niasdigital.com diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index f1d0a1371695..74a18a7f8f40 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -979,6 +979,20 @@ config SMC911X called smc911x. If you want to compile it as a module, say M here and read +config SMSC911X + tristate "SMSC LAN911x/LAN921x families embedded ethernet support" + depends on ARM || SUPERH + select CRC32 + select MII + select PHYLIB + ---help--- + Say Y here if you want support for SMSC LAN911x and LAN921x families + of ethernet controllers. + + To compile this driver as a module, choose M here and read + . The module + will be called smsc911x. + config NET_VENDOR_RACAL bool "Racal-Interlan (Micom) NI cards" depends on ISA diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 657c47b1a6b6..e06829aa75b0 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -219,6 +219,7 @@ obj-$(CONFIG_S2IO) += s2io.o obj-$(CONFIG_MYRI10GE) += myri10ge/ obj-$(CONFIG_SMC91X) += smc91x.o obj-$(CONFIG_SMC911X) += smc911x.o +obj-$(CONFIG_SMSC911X) += smsc911x.o obj-$(CONFIG_BFIN_MAC) += bfin_mac.o obj-$(CONFIG_DM9000) += dm9000.o obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c index 73baa7a3bb0e..c05d38d46350 100644 --- a/drivers/net/phy/smsc.c +++ b/drivers/net/phy/smsc.c @@ -126,6 +126,27 @@ static struct phy_driver lan8700_driver = { .driver = { .owner = THIS_MODULE, } }; +static struct phy_driver lan911x_int_driver = { + .phy_id = 0x0007c0d0, /* OUI=0x00800f, Model#=0x0d */ + .phy_id_mask = 0xfffffff0, + .name = "SMSC LAN911x Internal PHY", + + .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause + | SUPPORTED_Asym_Pause), + .flags = PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG, + + /* basic functions */ + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .config_init = smsc_phy_config_init, + + /* IRQ related */ + .ack_interrupt = smsc_phy_ack_interrupt, + .config_intr = smsc_phy_config_intr, + + .driver = { .owner = THIS_MODULE, } +}; + static int __init smsc_init(void) { int ret; @@ -142,8 +163,14 @@ static int __init smsc_init(void) if (ret) goto err3; + ret = phy_driver_register (&lan911x_int_driver); + if (ret) + goto err4; + return 0; +err4: + phy_driver_unregister (&lan8700_driver); err3: phy_driver_unregister (&lan8187_driver); err2: @@ -154,6 +181,7 @@ err1: static void __exit smsc_exit(void) { + phy_driver_unregister (&lan911x_int_driver); phy_driver_unregister (&lan8700_driver); phy_driver_unregister (&lan8187_driver); phy_driver_unregister (&lan83c185_driver); diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c new file mode 100644 index 000000000000..fe517880fc97 --- /dev/null +++ b/drivers/net/smsc911x.c @@ -0,0 +1,2091 @@ +/*************************************************************************** + * + * Copyright (C) 2004-2008 SMSC + * Copyright (C) 2005-2008 ARM + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + *************************************************************************** + * Rewritten, heavily based on smsc911x simple driver by SMSC. + * Partly uses io macros from smc91x.c by Nicolas Pitre + * + * Supported devices: + * LAN9115, LAN9116, LAN9117, LAN9118 + * LAN9215, LAN9216, LAN9217, LAN9218 + * LAN9210, LAN9211 + * LAN9220, LAN9221 + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "smsc911x.h" + +#define SMSC_CHIPNAME "smsc911x" +#define SMSC_MDIONAME "smsc911x-mdio" +#define SMSC_DRV_VERSION "2008-10-21" + +MODULE_LICENSE("GPL"); +MODULE_VERSION(SMSC_DRV_VERSION); + +#if USE_DEBUG > 0 +static int debug = 16; +#else +static int debug = 3; +#endif + +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + +struct smsc911x_data { + void __iomem *ioaddr; + + unsigned int idrev; + + /* used to decide which workarounds apply */ + unsigned int generation; + + /* device configuration (copied from platform_data during probe) */ + unsigned int irq_polarity; + unsigned int irq_type; + phy_interface_t phy_interface; + + /* This needs to be acquired before calling any of below: + * smsc911x_mac_read(), smsc911x_mac_write() + */ + spinlock_t mac_lock; + +#if (!SMSC_CAN_USE_32BIT) + /* spinlock to ensure 16-bit accesses are serialised */ + spinlock_t dev_lock; +#endif + + struct phy_device *phy_dev; + struct mii_bus *mii_bus; + int phy_irq[PHY_MAX_ADDR]; + unsigned int using_extphy; + int last_duplex; + int last_carrier; + + u32 msg_enable; + unsigned int gpio_setting; + unsigned int gpio_orig_setting; + struct net_device *dev; + struct napi_struct napi; + + unsigned int software_irq_signal; + +#ifdef USE_PHY_WORK_AROUND +#define MIN_PACKET_SIZE (64) + char loopback_tx_pkt[MIN_PACKET_SIZE]; + char loopback_rx_pkt[MIN_PACKET_SIZE]; + unsigned int resetcount; +#endif + + /* Members for Multicast filter workaround */ + unsigned int multicast_update_pending; + unsigned int set_bits_mask; + unsigned int clear_bits_mask; + unsigned int hashhi; + unsigned int hashlo; +}; + +#if SMSC_CAN_USE_32BIT + +static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) +{ + return readl(pdata->ioaddr + reg); +} + +static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, + u32 val) +{ + writel(val, pdata->ioaddr + reg); +} + +/* Writes a packet to the TX_DATA_FIFO */ +static inline void +smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount); +} + +/* Reads a packet out of the RX_DATA_FIFO */ +static inline void +smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount); +} + +#else /* SMSC_CAN_USE_32BIT */ + +/* These 16-bit access functions are significantly slower, due to the locking + * necessary. If your bus hardware can be configured to do this for you + * (in response to a single 32-bit operation from software), you should use + * the 32-bit access functions instead. */ + +static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) +{ + unsigned long flags; + u32 data; + + /* these two 16-bit reads must be performed consecutively, so must + * not be interrupted by our own ISR (which would start another + * read operation) */ + spin_lock_irqsave(&pdata->dev_lock, flags); + data = ((readw(pdata->ioaddr + reg) & 0xFFFF) | + ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16)); + spin_unlock_irqrestore(&pdata->dev_lock, flags); + + return data; +} + +static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, + u32 val) +{ + unsigned long flags; + + /* these two 16-bit writes must be performed consecutively, so must + * not be interrupted by our own ISR (which would start another + * read operation) */ + spin_lock_irqsave(&pdata->dev_lock, flags); + writew(val & 0xFFFF, pdata->ioaddr + reg); + writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2); + spin_unlock_irqrestore(&pdata->dev_lock, flags); +} + +/* Writes a packet to the TX_DATA_FIFO */ +static inline void +smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + while (wordcount--) + smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++); +} + +/* Reads a packet out of the RX_DATA_FIFO */ +static inline void +smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + while (wordcount--) + *buf++ = smsc911x_reg_read(pdata, RX_DATA_FIFO); +} + +#endif /* SMSC_CAN_USE_32BIT */ + +/* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read + * and smsc911x_mac_write, so assumes mac_lock is held */ +static int smsc911x_mac_complete(struct smsc911x_data *pdata) +{ + int i; + u32 val; + + SMSC_ASSERT_MAC_LOCK(pdata); + + for (i = 0; i < 40; i++) { + val = smsc911x_reg_read(pdata, MAC_CSR_CMD); + if (!(val & MAC_CSR_CMD_CSR_BUSY_)) + return 0; + } + SMSC_WARNING(HW, "Timed out waiting for MAC not BUSY. " + "MAC_CSR_CMD: 0x%08X", val); + return -EIO; +} + +/* Fetches a MAC register value. Assumes mac_lock is acquired */ +static u32 smsc911x_mac_read(struct smsc911x_data *pdata, unsigned int offset) +{ + unsigned int temp; + + SMSC_ASSERT_MAC_LOCK(pdata); + + temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); + if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { + SMSC_WARNING(HW, "MAC busy at entry"); + return 0xFFFFFFFF; + } + + /* Send the MAC cmd */ + smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | + MAC_CSR_CMD_CSR_BUSY_ | MAC_CSR_CMD_R_NOT_W_)); + + /* Workaround for hardware read-after-write restriction */ + temp = smsc911x_reg_read(pdata, BYTE_TEST); + + /* Wait for the read to complete */ + if (likely(smsc911x_mac_complete(pdata) == 0)) + return smsc911x_reg_read(pdata, MAC_CSR_DATA); + + SMSC_WARNING(HW, "MAC busy after read"); + return 0xFFFFFFFF; +} + +/* Set a mac register, mac_lock must be acquired before calling */ +static void smsc911x_mac_write(struct smsc911x_data *pdata, + unsigned int offset, u32 val) +{ + unsigned int temp; + + SMSC_ASSERT_MAC_LOCK(pdata); + + temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); + if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { + SMSC_WARNING(HW, + "smsc911x_mac_write failed, MAC busy at entry"); + return; + } + + /* Send data to write */ + smsc911x_reg_write(pdata, MAC_CSR_DATA, val); + + /* Write the actual data */ + smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | + MAC_CSR_CMD_CSR_BUSY_)); + + /* Workaround for hardware read-after-write restriction */ + temp = smsc911x_reg_read(pdata, BYTE_TEST); + + /* Wait for the write to complete */ + if (likely(smsc911x_mac_complete(pdata) == 0)) + return; + + SMSC_WARNING(HW, + "smsc911x_mac_write failed, MAC busy after write"); +} + +/* Get a phy register */ +static int smsc911x_mii_read(struct mii_bus *bus, int phyaddr, int regidx) +{ + struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv; + unsigned long flags; + unsigned int addr; + int i, reg; + + spin_lock_irqsave(&pdata->mac_lock, flags); + + /* Confirm MII not busy */ + if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + SMSC_WARNING(HW, + "MII is busy in smsc911x_mii_read???"); + reg = -EIO; + goto out; + } + + /* Set the address, index & direction (read from PHY) */ + addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6); + smsc911x_mac_write(pdata, MII_ACC, addr); + + /* Wait for read to complete w/ timeout */ + for (i = 0; i < 100; i++) + if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + reg = smsc911x_mac_read(pdata, MII_DATA); + goto out; + } + + SMSC_WARNING(HW, "Timed out waiting for MII write to finish"); + reg = -EIO; + +out: + spin_unlock_irqrestore(&pdata->mac_lock, flags); + return reg; +} + +/* Set a phy register */ +static int smsc911x_mii_write(struct mii_bus *bus, int phyaddr, int regidx, + u16 val) +{ + struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv; + unsigned long flags; + unsigned int addr; + int i, reg; + + spin_lock_irqsave(&pdata->mac_lock, flags); + + /* Confirm MII not busy */ + if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + SMSC_WARNING(HW, + "MII is busy in smsc911x_mii_write???"); + reg = -EIO; + goto out; + } + + /* Put the data to write in the MAC */ + smsc911x_mac_write(pdata, MII_DATA, val); + + /* Set the address, index & direction (write to PHY) */ + addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6) | + MII_ACC_MII_WRITE_; + smsc911x_mac_write(pdata, MII_ACC, addr); + + /* Wait for write to complete w/ timeout */ + for (i = 0; i < 100; i++) + if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + reg = 0; + goto out; + } + + SMSC_WARNING(HW, "Timed out waiting for MII write to finish"); + reg = -EIO; + +out: + spin_unlock_irqrestore(&pdata->mac_lock, flags); + return reg; +} + +/* Autodetects and initialises external phy for SMSC9115 and SMSC9117 flavors. + * If something goes wrong, returns -ENODEV to revert back to internal phy. + * Performed at initialisation only, so interrupts are enabled */ +static int smsc911x_phy_initialise_external(struct smsc911x_data *pdata) +{ + unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); + + /* External phy is requested, supported, and detected */ + if (hwcfg & HW_CFG_EXT_PHY_DET_) { + + /* Switch to external phy. Assuming tx and rx are stopped + * because smsc911x_phy_initialise is called before + * smsc911x_rx_initialise and tx_initialise. */ + + /* Disable phy clocks to the MAC */ + hwcfg &= (~HW_CFG_PHY_CLK_SEL_); + hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + udelay(10); /* Enough time for clocks to stop */ + + /* Switch to external phy */ + hwcfg |= HW_CFG_EXT_PHY_EN_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + + /* Enable phy clocks to the MAC */ + hwcfg &= (~HW_CFG_PHY_CLK_SEL_); + hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + udelay(10); /* Enough time for clocks to restart */ + + hwcfg |= HW_CFG_SMI_SEL_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + + SMSC_TRACE(HW, "Successfully switched to external PHY"); + pdata->using_extphy = 1; + } else { + SMSC_WARNING(HW, "No external PHY detected, " + "Using internal PHY instead."); + /* Use internal phy */ + return -ENODEV; + } + return 0; +} + +/* Fetches a tx status out of the status fifo */ +static unsigned int smsc911x_tx_get_txstatus(struct smsc911x_data *pdata) +{ + unsigned int result = + smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TSUSED_; + + if (result != 0) + result = smsc911x_reg_read(pdata, TX_STATUS_FIFO); + + return result; +} + +/* Fetches the next rx status */ +static unsigned int smsc911x_rx_get_rxstatus(struct smsc911x_data *pdata) +{ + unsigned int result = + smsc911x_reg_read(pdata, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED_; + + if (result != 0) + result = smsc911x_reg_read(pdata, RX_STATUS_FIFO); + + return result; +} + +#ifdef USE_PHY_WORK_AROUND +static int smsc911x_phy_check_loopbackpkt(struct smsc911x_data *pdata) +{ + unsigned int tries; + u32 wrsz; + u32 rdsz; + ulong bufp; + + for (tries = 0; tries < 10; tries++) { + unsigned int txcmd_a; + unsigned int txcmd_b; + unsigned int status; + unsigned int pktlength; + unsigned int i; + + /* Zero-out rx packet memory */ + memset(pdata->loopback_rx_pkt, 0, MIN_PACKET_SIZE); + + /* Write tx packet to 118 */ + txcmd_a = (u32)((ulong)pdata->loopback_tx_pkt & 0x03) << 16; + txcmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; + txcmd_a |= MIN_PACKET_SIZE; + + txcmd_b = MIN_PACKET_SIZE << 16 | MIN_PACKET_SIZE; + + smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_a); + smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_b); + + bufp = (ulong)pdata->loopback_tx_pkt & (~0x3); + wrsz = MIN_PACKET_SIZE + 3; + wrsz += (u32)((ulong)pdata->loopback_tx_pkt & 0x3); + wrsz >>= 2; + + smsc911x_tx_writefifo(pdata, (unsigned int *)bufp, wrsz); + + /* Wait till transmit is done */ + i = 60; + do { + udelay(5); + status = smsc911x_tx_get_txstatus(pdata); + } while ((i--) && (!status)); + + if (!status) { + SMSC_WARNING(HW, "Failed to transmit " + "during loopback test"); + continue; + } + if (status & TX_STS_ES_) { + SMSC_WARNING(HW, "Transmit encountered " + "errors during loopback test"); + continue; + } + + /* Wait till receive is done */ + i = 60; + do { + udelay(5); + status = smsc911x_rx_get_rxstatus(pdata); + } while ((i--) && (!status)); + + if (!status) { + SMSC_WARNING(HW, + "Failed to receive during loopback test"); + continue; + } + if (status & RX_STS_ES_) { + SMSC_WARNING(HW, "Receive encountered " + "errors during loopback test"); + continue; + } + + pktlength = ((status & 0x3FFF0000UL) >> 16); + bufp = (ulong)pdata->loopback_rx_pkt; + rdsz = pktlength + 3; + rdsz += (u32)((ulong)pdata->loopback_rx_pkt & 0x3); + rdsz >>= 2; + + smsc911x_rx_readfifo(pdata, (unsigned int *)bufp, rdsz); + + if (pktlength != (MIN_PACKET_SIZE + 4)) { + SMSC_WARNING(HW, "Unexpected packet size " + "during loop back test, size=%d, will retry", + pktlength); + } else { + unsigned int j; + int mismatch = 0; + for (j = 0; j < MIN_PACKET_SIZE; j++) { + if (pdata->loopback_tx_pkt[j] + != pdata->loopback_rx_pkt[j]) { + mismatch = 1; + break; + } + } + if (!mismatch) { + SMSC_TRACE(HW, "Successfully verified " + "loopback packet"); + return 0; + } else { + SMSC_WARNING(HW, "Data mismatch " + "during loop back test, will retry"); + } + } + } + + return -EIO; +} + +static int smsc911x_phy_reset(struct smsc911x_data *pdata) +{ + struct phy_device *phy_dev = pdata->phy_dev; + unsigned int temp; + unsigned int i = 100000; + + BUG_ON(!phy_dev); + BUG_ON(!phy_dev->bus); + + SMSC_TRACE(HW, "Performing PHY BCR Reset"); + smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, BMCR_RESET); + do { + msleep(1); + temp = smsc911x_mii_read(phy_dev->bus, phy_dev->addr, + MII_BMCR); + } while ((i--) && (temp & BMCR_RESET)); + + if (temp & BMCR_RESET) { + SMSC_WARNING(HW, "PHY reset failed to complete."); + return -EIO; + } + /* Extra delay required because the phy may not be completed with + * its reset when BMCR_RESET is cleared. Specs say 256 uS is + * enough delay but using 1ms here to be safe */ + msleep(1); + + return 0; +} + +static int smsc911x_phy_loopbacktest(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phy_dev = pdata->phy_dev; + int result = -EIO; + unsigned int i, val; + unsigned long flags; + + /* Initialise tx packet using broadcast destination address */ + memset(pdata->loopback_tx_pkt, 0xff, ETH_ALEN); + + /* Use incrementing source address */ + for (i = 6; i < 12; i++) + pdata->loopback_tx_pkt[i] = (char)i; + + /* Set length type field */ + pdata->loopback_tx_pkt[12] = 0x00; + pdata->loopback_tx_pkt[13] = 0x00; + + for (i = 14; i < MIN_PACKET_SIZE; i++) + pdata->loopback_tx_pkt[i] = (char)i; + + val = smsc911x_reg_read(pdata, HW_CFG); + val &= HW_CFG_TX_FIF_SZ_; + val |= HW_CFG_SF_; + smsc911x_reg_write(pdata, HW_CFG, val); + + smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); + smsc911x_reg_write(pdata, RX_CFG, + (u32)((ulong)pdata->loopback_rx_pkt & 0x03) << 8); + + for (i = 0; i < 10; i++) { + /* Set PHY to 10/FD, no ANEG, and loopback mode */ + smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, + BMCR_LOOPBACK | BMCR_FULLDPLX); + + /* Enable MAC tx/rx, FD */ + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, MAC_CR, MAC_CR_FDPX_ + | MAC_CR_TXEN_ | MAC_CR_RXEN_); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + if (smsc911x_phy_check_loopbackpkt(pdata) == 0) { + result = 0; + break; + } + pdata->resetcount++; + + /* Disable MAC rx */ + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, MAC_CR, 0); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + smsc911x_phy_reset(pdata); + } + + /* Disable MAC */ + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, MAC_CR, 0); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + /* Cancel PHY loopback mode */ + smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, 0); + + smsc911x_reg_write(pdata, TX_CFG, 0); + smsc911x_reg_write(pdata, RX_CFG, 0); + + return result; +} +#endif /* USE_PHY_WORK_AROUND */ + +static u8 smsc95xx_resolve_flowctrl_fulldplx(u16 lcladv, u16 rmtadv) +{ + u8 cap = 0; + + if (lcladv & ADVERTISE_PAUSE_CAP) { + if (lcladv & ADVERTISE_PAUSE_ASYM) { + if (rmtadv & LPA_PAUSE_CAP) + cap = FLOW_CTRL_TX | FLOW_CTRL_RX; + else if (rmtadv & LPA_PAUSE_ASYM) + cap = FLOW_CTRL_RX; + } else { + if (rmtadv & LPA_PAUSE_CAP) + cap = FLOW_CTRL_TX | FLOW_CTRL_RX; + } + } else if (lcladv & ADVERTISE_PAUSE_ASYM) { + if ((rmtadv & LPA_PAUSE_CAP) && (rmtadv & LPA_PAUSE_ASYM)) + cap = FLOW_CTRL_TX; + } + + return cap; +} + +static void smsc911x_phy_update_flowcontrol(struct smsc911x_data *pdata) +{ + struct phy_device *phy_dev = pdata->phy_dev; + u32 afc = smsc911x_reg_read(pdata, AFC_CFG); + u32 flow; + unsigned long flags; + + if (phy_dev->duplex == DUPLEX_FULL) { + u16 lcladv = phy_read(phy_dev, MII_ADVERTISE); + u16 rmtadv = phy_read(phy_dev, MII_LPA); + u8 cap = smsc95xx_resolve_flowctrl_fulldplx(lcladv, rmtadv); + + if (cap & FLOW_CTRL_RX) + flow = 0xFFFF0002; + else + flow = 0; + + if (cap & FLOW_CTRL_TX) + afc |= 0xF; + else + afc &= ~0xF; + + SMSC_TRACE(HW, "rx pause %s, tx pause %s", + (cap & FLOW_CTRL_RX ? "enabled" : "disabled"), + (cap & FLOW_CTRL_TX ? "enabled" : "disabled")); + } else { + SMSC_TRACE(HW, "half duplex"); + flow = 0; + afc |= 0xF; + } + + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, FLOW, flow); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + smsc911x_reg_write(pdata, AFC_CFG, afc); +} + +/* Update link mode if anything has changed. Called periodically when the + * PHY is in polling mode, even if nothing has changed. */ +static void smsc911x_phy_adjust_link(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phy_dev = pdata->phy_dev; + unsigned long flags; + int carrier; + + if (phy_dev->duplex != pdata->last_duplex) { + unsigned int mac_cr; + SMSC_TRACE(HW, "duplex state has changed"); + + spin_lock_irqsave(&pdata->mac_lock, flags); + mac_cr = smsc911x_mac_read(pdata, MAC_CR); + if (phy_dev->duplex) { + SMSC_TRACE(HW, + "configuring for full duplex mode"); + mac_cr |= MAC_CR_FDPX_; + } else { + SMSC_TRACE(HW, + "configuring for half duplex mode"); + mac_cr &= ~MAC_CR_FDPX_; + } + smsc911x_mac_write(pdata, MAC_CR, mac_cr); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + smsc911x_phy_update_flowcontrol(pdata); + pdata->last_duplex = phy_dev->duplex; + } + + carrier = netif_carrier_ok(dev); + if (carrier != pdata->last_carrier) { + SMSC_TRACE(HW, "carrier state has changed"); + if (carrier) { + SMSC_TRACE(HW, "configuring for carrier OK"); + if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) && + (!pdata->using_extphy)) { + /* Restore orginal GPIO configuration */ + pdata->gpio_setting = pdata->gpio_orig_setting; + smsc911x_reg_write(pdata, GPIO_CFG, + pdata->gpio_setting); + } + } else { + SMSC_TRACE(HW, "configuring for no carrier"); + /* Check global setting that LED1 + * usage is 10/100 indicator */ + pdata->gpio_setting = smsc911x_reg_read(pdata, + GPIO_CFG); + if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) + && (!pdata->using_extphy)) { + /* Force 10/100 LED off, after saving + * orginal GPIO configuration */ + pdata->gpio_orig_setting = pdata->gpio_setting; + + pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_; + pdata->gpio_setting |= (GPIO_CFG_GPIOBUF0_ + | GPIO_CFG_GPIODIR0_ + | GPIO_CFG_GPIOD0_); + smsc911x_reg_write(pdata, GPIO_CFG, + pdata->gpio_setting); + } + } + pdata->last_carrier = carrier; + } +} + +static int smsc911x_mii_probe(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phydev = NULL; + int phy_addr; + + /* find the first phy */ + for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) { + if (pdata->mii_bus->phy_map[phy_addr]) { + phydev = pdata->mii_bus->phy_map[phy_addr]; + SMSC_TRACE(PROBE, "PHY %d: addr %d, phy_id 0x%08X", + phy_addr, phydev->addr, phydev->phy_id); + break; + } + } + + if (!phydev) { + pr_err("%s: no PHY found\n", dev->name); + return -ENODEV; + } + + phydev = phy_connect(dev, phydev->dev.bus_id, + &smsc911x_phy_adjust_link, 0, pdata->phy_interface); + + if (IS_ERR(phydev)) { + pr_err("%s: Could not attach to PHY\n", dev->name); + return PTR_ERR(phydev); + } + + pr_info("%s: attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n", + dev->name, phydev->drv->name, phydev->dev.bus_id, phydev->irq); + + /* mask with MAC supported features */ + phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause | + SUPPORTED_Asym_Pause); + phydev->advertising = phydev->supported; + + pdata->phy_dev = phydev; + pdata->last_duplex = -1; + pdata->last_carrier = -1; + +#ifdef USE_PHY_WORK_AROUND + if (smsc911x_phy_loopbacktest(dev) < 0) { + SMSC_WARNING(HW, "Failed Loop Back Test"); + return -ENODEV; + } + SMSC_TRACE(HW, "Passed Loop Back Test"); +#endif /* USE_PHY_WORK_AROUND */ + + SMSC_TRACE(HW, "phy initialised succesfully"); + return 0; +} + +static int __devinit smsc911x_mii_init(struct platform_device *pdev, + struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + int err = -ENXIO, i; + + pdata->mii_bus = mdiobus_alloc(); + if (!pdata->mii_bus) { + err = -ENOMEM; + goto err_out_1; + } + + pdata->mii_bus->name = SMSC_MDIONAME; + snprintf(pdata->mii_bus->id, MII_BUS_ID_SIZE, "%x", pdev->id); + pdata->mii_bus->priv = pdata; + pdata->mii_bus->read = smsc911x_mii_read; + pdata->mii_bus->write = smsc911x_mii_write; + pdata->mii_bus->irq = pdata->phy_irq; + for (i = 0; i < PHY_MAX_ADDR; ++i) + pdata->mii_bus->irq[i] = PHY_POLL; + + pdata->mii_bus->parent = &pdev->dev; + dev_set_drvdata(&pdev->dev, &pdata->mii_bus); + + pdata->using_extphy = 0; + + switch (pdata->idrev & 0xFFFF0000) { + case 0x01170000: + case 0x01150000: + case 0x117A0000: + case 0x115A0000: + /* External PHY supported, try to autodetect */ + if (smsc911x_phy_initialise_external(pdata) < 0) { + SMSC_TRACE(HW, "No external PHY detected, " + "using internal PHY"); + } + break; + default: + SMSC_TRACE(HW, "External PHY is not supported, " + "using internal PHY"); + break; + } + + if (!pdata->using_extphy) { + /* Mask all PHYs except ID 1 (internal) */ + pdata->mii_bus->phy_mask = ~(1 << 1); + } + + if (mdiobus_register(pdata->mii_bus)) { + SMSC_WARNING(PROBE, "Error registering mii bus"); + goto err_out_free_bus_2; + } + + if (smsc911x_mii_probe(dev) < 0) { + SMSC_WARNING(PROBE, "Error registering mii bus"); + goto err_out_unregister_bus_3; + } + + return 0; + +err_out_unregister_bus_3: + mdiobus_unregister(pdata->mii_bus); +err_out_free_bus_2: + mdiobus_free(pdata->mii_bus); +err_out_1: + return err; +} + +/* Gets the number of tx statuses in the fifo */ +static unsigned int smsc911x_tx_get_txstatcount(struct smsc911x_data *pdata) +{ + return (smsc911x_reg_read(pdata, TX_FIFO_INF) + & TX_FIFO_INF_TSUSED_) >> 16; +} + +/* Reads tx statuses and increments counters where necessary */ +static void smsc911x_tx_update_txcounters(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int tx_stat; + + while ((tx_stat = smsc911x_tx_get_txstatus(pdata)) != 0) { + if (unlikely(tx_stat & 0x80000000)) { + /* In this driver the packet tag is used as the packet + * length. Since a packet length can never reach the + * size of 0x8000, this bit is reserved. It is worth + * noting that the "reserved bit" in the warning above + * does not reference a hardware defined reserved bit + * but rather a driver defined one. + */ + SMSC_WARNING(HW, + "Packet tag reserved bit is high"); + } else { + if (unlikely(tx_stat & 0x00008000)) { + dev->stats.tx_errors++; + } else { + dev->stats.tx_packets++; + dev->stats.tx_bytes += (tx_stat >> 16); + } + if (unlikely(tx_stat & 0x00000100)) { + dev->stats.collisions += 16; + dev->stats.tx_aborted_errors += 1; + } else { + dev->stats.collisions += + ((tx_stat >> 3) & 0xF); + } + if (unlikely(tx_stat & 0x00000800)) + dev->stats.tx_carrier_errors += 1; + if (unlikely(tx_stat & 0x00000200)) { + dev->stats.collisions++; + dev->stats.tx_aborted_errors++; + } + } + } +} + +/* Increments the Rx error counters */ +static void +smsc911x_rx_counterrors(struct net_device *dev, unsigned int rxstat) +{ + int crc_err = 0; + + if (unlikely(rxstat & 0x00008000)) { + dev->stats.rx_errors++; + if (unlikely(rxstat & 0x00000002)) { + dev->stats.rx_crc_errors++; + crc_err = 1; + } + } + if (likely(!crc_err)) { + if (unlikely((rxstat & 0x00001020) == 0x00001020)) { + /* Frame type indicates length, + * and length error is set */ + dev->stats.rx_length_errors++; + } + if (rxstat & RX_STS_MCAST_) + dev->stats.multicast++; + } +} + +/* Quickly dumps bad packets */ +static void +smsc911x_rx_fastforward(struct smsc911x_data *pdata, unsigned int pktbytes) +{ + unsigned int pktwords = (pktbytes + NET_IP_ALIGN + 3) >> 2; + + if (likely(pktwords >= 4)) { + unsigned int timeout = 500; + unsigned int val; + smsc911x_reg_write(pdata, RX_DP_CTRL, RX_DP_CTRL_RX_FFWD_); + do { + udelay(1); + val = smsc911x_reg_read(pdata, RX_DP_CTRL); + } while (timeout-- && (val & RX_DP_CTRL_RX_FFWD_)); + + if (unlikely(timeout == 0)) + SMSC_WARNING(HW, "Timed out waiting for " + "RX FFWD to finish, RX_DP_CTRL: 0x%08X", val); + } else { + unsigned int temp; + while (pktwords--) + temp = smsc911x_reg_read(pdata, RX_DATA_FIFO); + } +} + +/* NAPI poll function */ +static int smsc911x_poll(struct napi_struct *napi, int budget) +{ + struct smsc911x_data *pdata = + container_of(napi, struct smsc911x_data, napi); + struct net_device *dev = pdata->dev; + int npackets = 0; + + while (likely(netif_running(dev)) && (npackets < budget)) { + unsigned int pktlength; + unsigned int pktwords; + struct sk_buff *skb; + unsigned int rxstat = smsc911x_rx_get_rxstatus(pdata); + + if (!rxstat) { + unsigned int temp; + /* We processed all packets available. Tell NAPI it can + * stop polling then re-enable rx interrupts */ + smsc911x_reg_write(pdata, INT_STS, INT_STS_RSFL_); + netif_rx_complete(dev, napi); + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= INT_EN_RSFL_EN_; + smsc911x_reg_write(pdata, INT_EN, temp); + break; + } + + /* Count packet for NAPI scheduling, even if it has an error. + * Error packets still require cycles to discard */ + npackets++; + + pktlength = ((rxstat & 0x3FFF0000) >> 16); + pktwords = (pktlength + NET_IP_ALIGN + 3) >> 2; + smsc911x_rx_counterrors(dev, rxstat); + + if (unlikely(rxstat & RX_STS_ES_)) { + SMSC_WARNING(RX_ERR, + "Discarding packet with error bit set"); + /* Packet has an error, discard it and continue with + * the next */ + smsc911x_rx_fastforward(pdata, pktwords); + dev->stats.rx_dropped++; + continue; + } + + skb = netdev_alloc_skb(dev, pktlength + NET_IP_ALIGN); + if (unlikely(!skb)) { + SMSC_WARNING(RX_ERR, + "Unable to allocate skb for rx packet"); + /* Drop the packet and stop this polling iteration */ + smsc911x_rx_fastforward(pdata, pktwords); + dev->stats.rx_dropped++; + break; + } + + skb->data = skb->head; + skb_reset_tail_pointer(skb); + + /* Align IP on 16B boundary */ + skb_reserve(skb, NET_IP_ALIGN); + skb_put(skb, pktlength - 4); + smsc911x_rx_readfifo(pdata, (unsigned int *)skb->head, + pktwords); + skb->protocol = eth_type_trans(skb, dev); + skb->ip_summed = CHECKSUM_NONE; + netif_receive_skb(skb); + + /* Update counters */ + dev->stats.rx_packets++; + dev->stats.rx_bytes += (pktlength - 4); + dev->last_rx = jiffies; + } + + /* Return total received packets */ + return npackets; +} + +/* Returns hash bit number for given MAC address + * Example: + * 01 00 5E 00 00 01 -> returns bit number 31 */ +static unsigned int smsc911x_hash(char addr[ETH_ALEN]) +{ + return (ether_crc(ETH_ALEN, addr) >> 26) & 0x3f; +} + +static void smsc911x_rx_multicast_update(struct smsc911x_data *pdata) +{ + /* Performs the multicast & mac_cr update. This is called when + * safe on the current hardware, and with the mac_lock held */ + unsigned int mac_cr; + + SMSC_ASSERT_MAC_LOCK(pdata); + + mac_cr = smsc911x_mac_read(pdata, MAC_CR); + mac_cr |= pdata->set_bits_mask; + mac_cr &= ~(pdata->clear_bits_mask); + smsc911x_mac_write(pdata, MAC_CR, mac_cr); + smsc911x_mac_write(pdata, HASHH, pdata->hashhi); + smsc911x_mac_write(pdata, HASHL, pdata->hashlo); + SMSC_TRACE(HW, "maccr 0x%08X, HASHH 0x%08X, HASHL 0x%08X", + mac_cr, pdata->hashhi, pdata->hashlo); +} + +static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata) +{ + unsigned int mac_cr; + + /* This function is only called for older LAN911x devices + * (revA or revB), where MAC_CR, HASHH and HASHL should not + * be modified during Rx - newer devices immediately update the + * registers. + * + * This is called from interrupt context */ + + spin_lock(&pdata->mac_lock); + + /* Check Rx has stopped */ + if (smsc911x_mac_read(pdata, MAC_CR) & MAC_CR_RXEN_) + SMSC_WARNING(DRV, "Rx not stopped"); + + /* Perform the update - safe to do now Rx has stopped */ + smsc911x_rx_multicast_update(pdata); + + /* Re-enable Rx */ + mac_cr = smsc911x_mac_read(pdata, MAC_CR); + mac_cr |= MAC_CR_RXEN_; + smsc911x_mac_write(pdata, MAC_CR, mac_cr); + + pdata->multicast_update_pending = 0; + + spin_unlock(&pdata->mac_lock); +} + +static int smsc911x_soft_reset(struct smsc911x_data *pdata) +{ + unsigned int timeout; + unsigned int temp; + + /* Reset the LAN911x */ + smsc911x_reg_write(pdata, HW_CFG, HW_CFG_SRST_); + timeout = 10; + do { + udelay(10); + temp = smsc911x_reg_read(pdata, HW_CFG); + } while ((--timeout) && (temp & HW_CFG_SRST_)); + + if (unlikely(temp & HW_CFG_SRST_)) { + SMSC_WARNING(DRV, "Failed to complete reset"); + return -EIO; + } + return 0; +} + +/* Sets the device MAC address to dev_addr, called with mac_lock held */ +static void +smsc911x_set_mac_address(struct smsc911x_data *pdata, u8 dev_addr[6]) +{ + u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4]; + u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) | + (dev_addr[1] << 8) | dev_addr[0]; + + SMSC_ASSERT_MAC_LOCK(pdata); + + smsc911x_mac_write(pdata, ADDRH, mac_high16); + smsc911x_mac_write(pdata, ADDRL, mac_low32); +} + +static int smsc911x_open(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int timeout; + unsigned int temp; + unsigned int intcfg; + + /* if the phy is not yet registered, retry later*/ + if (!pdata->phy_dev) { + SMSC_WARNING(HW, "phy_dev is NULL"); + return -EAGAIN; + } + + if (!is_valid_ether_addr(dev->dev_addr)) { + SMSC_WARNING(HW, "dev_addr is not a valid MAC address"); + return -EADDRNOTAVAIL; + } + + /* Reset the LAN911x */ + if (smsc911x_soft_reset(pdata)) { + SMSC_WARNING(HW, "soft reset failed"); + return -EIO; + } + + smsc911x_reg_write(pdata, HW_CFG, 0x00050000); + smsc911x_reg_write(pdata, AFC_CFG, 0x006E3740); + + /* Make sure EEPROM has finished loading before setting GPIO_CFG */ + timeout = 50; + while ((timeout--) && + (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_)) { + udelay(10); + } + + if (unlikely(timeout == 0)) + SMSC_WARNING(IFUP, + "Timed out waiting for EEPROM busy bit to clear"); + + smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000); + + /* The soft reset above cleared the device's MAC address, + * restore it from local copy (set in probe) */ + spin_lock_irq(&pdata->mac_lock); + smsc911x_set_mac_address(pdata, dev->dev_addr); + spin_unlock_irq(&pdata->mac_lock); + + /* Initialise irqs, but leave all sources disabled */ + smsc911x_reg_write(pdata, INT_EN, 0); + smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF); + + /* Set interrupt deassertion to 100uS */ + intcfg = ((10 << 24) | INT_CFG_IRQ_EN_); + + if (pdata->irq_polarity) { + SMSC_TRACE(IFUP, "irq polarity: active high"); + intcfg |= INT_CFG_IRQ_POL_; + } else { + SMSC_TRACE(IFUP, "irq polarity: active low"); + } + + if (pdata->irq_type) { + SMSC_TRACE(IFUP, "irq type: push-pull"); + intcfg |= INT_CFG_IRQ_TYPE_; + } else { + SMSC_TRACE(IFUP, "irq type: open drain"); + } + + smsc911x_reg_write(pdata, INT_CFG, intcfg); + + SMSC_TRACE(IFUP, "Testing irq handler using IRQ %d", dev->irq); + pdata->software_irq_signal = 0; + smp_wmb(); + + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= INT_EN_SW_INT_EN_; + smsc911x_reg_write(pdata, INT_EN, temp); + + timeout = 1000; + while (timeout--) { + if (pdata->software_irq_signal) + break; + msleep(1); + } + + if (!pdata->software_irq_signal) { + dev_warn(&dev->dev, "ISR failed signaling test (IRQ %d)\n", + dev->irq); + return -ENODEV; + } + SMSC_TRACE(IFUP, "IRQ handler passed test using IRQ %d", dev->irq); + + dev_info(&dev->dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n", + (unsigned long)pdata->ioaddr, dev->irq); + + /* Bring the PHY up */ + phy_start(pdata->phy_dev); + + temp = smsc911x_reg_read(pdata, HW_CFG); + /* Preserve TX FIFO size and external PHY configuration */ + temp &= (HW_CFG_TX_FIF_SZ_|0x00000FFF); + temp |= HW_CFG_SF_; + smsc911x_reg_write(pdata, HW_CFG, temp); + + temp = smsc911x_reg_read(pdata, FIFO_INT); + temp |= FIFO_INT_TX_AVAIL_LEVEL_; + temp &= ~(FIFO_INT_RX_STS_LEVEL_); + smsc911x_reg_write(pdata, FIFO_INT, temp); + + /* set RX Data offset to 2 bytes for alignment */ + smsc911x_reg_write(pdata, RX_CFG, (2 << 8)); + + /* enable NAPI polling before enabling RX interrupts */ + napi_enable(&pdata->napi); + + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= (INT_EN_TDFA_EN_ | INT_EN_RSFL_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + + spin_lock_irq(&pdata->mac_lock); + temp = smsc911x_mac_read(pdata, MAC_CR); + temp |= (MAC_CR_TXEN_ | MAC_CR_RXEN_ | MAC_CR_HBDIS_); + smsc911x_mac_write(pdata, MAC_CR, temp); + spin_unlock_irq(&pdata->mac_lock); + + smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); + + netif_start_queue(dev); + return 0; +} + +/* Entry point for stopping the interface */ +static int smsc911x_stop(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int temp; + + BUG_ON(!pdata->phy_dev); + + /* Disable all device interrupts */ + temp = smsc911x_reg_read(pdata, INT_CFG); + temp &= ~INT_CFG_IRQ_EN_; + smsc911x_reg_write(pdata, INT_CFG, temp); + + /* Stop Tx and Rx polling */ + netif_stop_queue(dev); + napi_disable(&pdata->napi); + + /* At this point all Rx and Tx activity is stopped */ + dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); + smsc911x_tx_update_txcounters(dev); + + /* Bring the PHY down */ + phy_stop(pdata->phy_dev); + + SMSC_TRACE(IFDOWN, "Interface stopped"); + return 0; +} + +/* Entry point for transmitting a packet */ +static int smsc911x_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int freespace; + unsigned int tx_cmd_a; + unsigned int tx_cmd_b; + unsigned int temp; + u32 wrsz; + ulong bufp; + + freespace = smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TDFREE_; + + if (unlikely(freespace < TX_FIFO_LOW_THRESHOLD)) + SMSC_WARNING(TX_ERR, + "Tx data fifo low, space available: %d", freespace); + + /* Word alignment adjustment */ + tx_cmd_a = (u32)((ulong)skb->data & 0x03) << 16; + tx_cmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; + tx_cmd_a |= (unsigned int)skb->len; + + tx_cmd_b = ((unsigned int)skb->len) << 16; + tx_cmd_b |= (unsigned int)skb->len; + + smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_a); + smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_b); + + bufp = (ulong)skb->data & (~0x3); + wrsz = (u32)skb->len + 3; + wrsz += (u32)((ulong)skb->data & 0x3); + wrsz >>= 2; + + smsc911x_tx_writefifo(pdata, (unsigned int *)bufp, wrsz); + freespace -= (skb->len + 32); + dev_kfree_skb(skb); + dev->trans_start = jiffies; + + if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30)) + smsc911x_tx_update_txcounters(dev); + + if (freespace < TX_FIFO_LOW_THRESHOLD) { + netif_stop_queue(dev); + temp = smsc911x_reg_read(pdata, FIFO_INT); + temp &= 0x00FFFFFF; + temp |= 0x32000000; + smsc911x_reg_write(pdata, FIFO_INT, temp); + } + + return NETDEV_TX_OK; +} + +/* Entry point for getting status counters */ +static struct net_device_stats *smsc911x_get_stats(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + smsc911x_tx_update_txcounters(dev); + dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); + return &dev->stats; +} + +/* Entry point for setting addressing modes */ +static void smsc911x_set_multicast_list(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned long flags; + + if (dev->flags & IFF_PROMISC) { + /* Enabling promiscuous mode */ + pdata->set_bits_mask = MAC_CR_PRMS_; + pdata->clear_bits_mask = (MAC_CR_MCPAS_ | MAC_CR_HPFILT_); + pdata->hashhi = 0; + pdata->hashlo = 0; + } else if (dev->flags & IFF_ALLMULTI) { + /* Enabling all multicast mode */ + pdata->set_bits_mask = MAC_CR_MCPAS_; + pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_); + pdata->hashhi = 0; + pdata->hashlo = 0; + } else if (dev->mc_count > 0) { + /* Enabling specific multicast addresses */ + unsigned int hash_high = 0; + unsigned int hash_low = 0; + unsigned int count = 0; + struct dev_mc_list *mc_list = dev->mc_list; + + pdata->set_bits_mask = MAC_CR_HPFILT_; + pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_); + + while (mc_list) { + count++; + if ((mc_list->dmi_addrlen) == ETH_ALEN) { + unsigned int bitnum = + smsc911x_hash(mc_list->dmi_addr); + unsigned int mask = 0x01 << (bitnum & 0x1F); + if (bitnum & 0x20) + hash_high |= mask; + else + hash_low |= mask; + } else { + SMSC_WARNING(DRV, "dmi_addrlen != 6"); + } + mc_list = mc_list->next; + } + if (count != (unsigned int)dev->mc_count) + SMSC_WARNING(DRV, "mc_count != dev->mc_count"); + + pdata->hashhi = hash_high; + pdata->hashlo = hash_low; + } else { + /* Enabling local MAC address only */ + pdata->set_bits_mask = 0; + pdata->clear_bits_mask = + (MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_); + pdata->hashhi = 0; + pdata->hashlo = 0; + } + + spin_lock_irqsave(&pdata->mac_lock, flags); + + if (pdata->generation <= 1) { + /* Older hardware revision - cannot change these flags while + * receiving data */ + if (!pdata->multicast_update_pending) { + unsigned int temp; + SMSC_TRACE(HW, "scheduling mcast update"); + pdata->multicast_update_pending = 1; + + /* Request the hardware to stop, then perform the + * update when we get an RX_STOP interrupt */ + smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_); + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= INT_EN_RXSTOP_INT_EN_; + smsc911x_reg_write(pdata, INT_EN, temp); + + temp = smsc911x_mac_read(pdata, MAC_CR); + temp &= ~(MAC_CR_RXEN_); + smsc911x_mac_write(pdata, MAC_CR, temp); + } else { + /* There is another update pending, this should now + * use the newer values */ + } + } else { + /* Newer hardware revision - can write immediately */ + smsc911x_rx_multicast_update(pdata); + } + + spin_unlock_irqrestore(&pdata->mac_lock, flags); +} + +static irqreturn_t smsc911x_irqhandler(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct smsc911x_data *pdata = netdev_priv(dev); + u32 intsts = smsc911x_reg_read(pdata, INT_STS); + u32 inten = smsc911x_reg_read(pdata, INT_EN); + int serviced = IRQ_NONE; + u32 temp; + + if (unlikely(intsts & inten & INT_STS_SW_INT_)) { + temp = smsc911x_reg_read(pdata, INT_EN); + temp &= (~INT_EN_SW_INT_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + smsc911x_reg_write(pdata, INT_STS, INT_STS_SW_INT_); + pdata->software_irq_signal = 1; + smp_wmb(); + serviced = IRQ_HANDLED; + } + + if (unlikely(intsts & inten & INT_STS_RXSTOP_INT_)) { + /* Called when there is a multicast update scheduled and + * it is now safe to complete the update */ + SMSC_TRACE(INTR, "RX Stop interrupt"); + temp = smsc911x_reg_read(pdata, INT_EN); + temp &= (~INT_EN_RXSTOP_INT_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_); + smsc911x_rx_multicast_update_workaround(pdata); + serviced = IRQ_HANDLED; + } + + if (intsts & inten & INT_STS_TDFA_) { + temp = smsc911x_reg_read(pdata, FIFO_INT); + temp |= FIFO_INT_TX_AVAIL_LEVEL_; + smsc911x_reg_write(pdata, FIFO_INT, temp); + smsc911x_reg_write(pdata, INT_STS, INT_STS_TDFA_); + netif_wake_queue(dev); + serviced = IRQ_HANDLED; + } + + if (unlikely(intsts & inten & INT_STS_RXE_)) { + SMSC_TRACE(INTR, "RX Error interrupt"); + smsc911x_reg_write(pdata, INT_STS, INT_STS_RXE_); + serviced = IRQ_HANDLED; + } + + if (likely(intsts & inten & INT_STS_RSFL_)) { + if (likely(netif_rx_schedule_prep(dev, &pdata->napi))) { + /* Disable Rx interrupts */ + temp = smsc911x_reg_read(pdata, INT_EN); + temp &= (~INT_EN_RSFL_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + /* Schedule a NAPI poll */ + __netif_rx_schedule(dev, &pdata->napi); + } else { + SMSC_WARNING(RX_ERR, + "netif_rx_schedule_prep failed"); + } + serviced = IRQ_HANDLED; + } + + return serviced; +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +void smsc911x_poll_controller(struct net_device *dev) +{ + disable_irq(dev->irq); + smsc911x_irqhandler(0, dev); + enable_irq(dev->irq); +} +#endif /* CONFIG_NET_POLL_CONTROLLER */ + +/* Standard ioctls for mii-tool */ +static int smsc911x_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + if (!netif_running(dev) || !pdata->phy_dev) + return -EINVAL; + + return phy_mii_ioctl(pdata->phy_dev, if_mii(ifr), cmd); +} + +static int +smsc911x_ethtool_getsettings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + cmd->maxtxpkt = 1; + cmd->maxrxpkt = 1; + return phy_ethtool_gset(pdata->phy_dev, cmd); +} + +static int +smsc911x_ethtool_setsettings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + return phy_ethtool_sset(pdata->phy_dev, cmd); +} + +static void smsc911x_ethtool_getdrvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + strlcpy(info->driver, SMSC_CHIPNAME, sizeof(info->driver)); + strlcpy(info->version, SMSC_DRV_VERSION, sizeof(info->version)); + strlcpy(info->bus_info, dev->dev.parent->bus_id, + sizeof(info->bus_info)); +} + +static int smsc911x_ethtool_nwayreset(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + return phy_start_aneg(pdata->phy_dev); +} + +static u32 smsc911x_ethtool_getmsglevel(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + return pdata->msg_enable; +} + +static void smsc911x_ethtool_setmsglevel(struct net_device *dev, u32 level) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + pdata->msg_enable = level; +} + +static int smsc911x_ethtool_getregslen(struct net_device *dev) +{ + return (((E2P_DATA - ID_REV) / 4 + 1) + (WUCSR - MAC_CR) + 1 + 32) * + sizeof(u32); +} + +static void +smsc911x_ethtool_getregs(struct net_device *dev, struct ethtool_regs *regs, + void *buf) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phy_dev = pdata->phy_dev; + unsigned long flags; + unsigned int i; + unsigned int j = 0; + u32 *data = buf; + + regs->version = pdata->idrev; + for (i = ID_REV; i <= E2P_DATA; i += (sizeof(u32))) + data[j++] = smsc911x_reg_read(pdata, i); + + for (i = MAC_CR; i <= WUCSR; i++) { + spin_lock_irqsave(&pdata->mac_lock, flags); + data[j++] = smsc911x_mac_read(pdata, i); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + } + + for (i = 0; i <= 31; i++) + data[j++] = smsc911x_mii_read(phy_dev->bus, phy_dev->addr, i); +} + +static void smsc911x_eeprom_enable_access(struct smsc911x_data *pdata) +{ + unsigned int temp = smsc911x_reg_read(pdata, GPIO_CFG); + temp &= ~GPIO_CFG_EEPR_EN_; + smsc911x_reg_write(pdata, GPIO_CFG, temp); + msleep(1); +} + +static int smsc911x_eeprom_send_cmd(struct smsc911x_data *pdata, u32 op) +{ + int timeout = 100; + u32 e2cmd; + + SMSC_TRACE(DRV, "op 0x%08x", op); + if (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) { + SMSC_WARNING(DRV, "Busy at start"); + return -EBUSY; + } + + e2cmd = op | E2P_CMD_EPC_BUSY_; + smsc911x_reg_write(pdata, E2P_CMD, e2cmd); + + do { + msleep(1); + e2cmd = smsc911x_reg_read(pdata, E2P_CMD); + } while ((e2cmd & E2P_CMD_EPC_BUSY_) && (timeout--)); + + if (!timeout) { + SMSC_TRACE(DRV, "TIMED OUT"); + return -EAGAIN; + } + + if (e2cmd & E2P_CMD_EPC_TIMEOUT_) { + SMSC_TRACE(DRV, "Error occured during eeprom operation"); + return -EINVAL; + } + + return 0; +} + +static int smsc911x_eeprom_read_location(struct smsc911x_data *pdata, + u8 address, u8 *data) +{ + u32 op = E2P_CMD_EPC_CMD_READ_ | address; + int ret; + + SMSC_TRACE(DRV, "address 0x%x", address); + ret = smsc911x_eeprom_send_cmd(pdata, op); + + if (!ret) + data[address] = smsc911x_reg_read(pdata, E2P_DATA); + + return ret; +} + +static int smsc911x_eeprom_write_location(struct smsc911x_data *pdata, + u8 address, u8 data) +{ + u32 op = E2P_CMD_EPC_CMD_ERASE_ | address; + int ret; + + SMSC_TRACE(DRV, "address 0x%x, data 0x%x", address, data); + ret = smsc911x_eeprom_send_cmd(pdata, op); + + if (!ret) { + op = E2P_CMD_EPC_CMD_WRITE_ | address; + smsc911x_reg_write(pdata, E2P_DATA, (u32)data); + ret = smsc911x_eeprom_send_cmd(pdata, op); + } + + return ret; +} + +static int smsc911x_ethtool_get_eeprom_len(struct net_device *dev) +{ + return SMSC911X_EEPROM_SIZE; +} + +static int smsc911x_ethtool_get_eeprom(struct net_device *dev, + struct ethtool_eeprom *eeprom, u8 *data) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + u8 eeprom_data[SMSC911X_EEPROM_SIZE]; + int len; + int i; + + smsc911x_eeprom_enable_access(pdata); + + len = min(eeprom->len, SMSC911X_EEPROM_SIZE); + for (i = 0; i < len; i++) { + int ret = smsc911x_eeprom_read_location(pdata, i, eeprom_data); + if (ret < 0) { + eeprom->len = 0; + return ret; + } + } + + memcpy(data, &eeprom_data[eeprom->offset], len); + eeprom->len = len; + return 0; +} + +static int smsc911x_ethtool_set_eeprom(struct net_device *dev, + struct ethtool_eeprom *eeprom, u8 *data) +{ + int ret; + struct smsc911x_data *pdata = netdev_priv(dev); + + smsc911x_eeprom_enable_access(pdata); + smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWEN_); + ret = smsc911x_eeprom_write_location(pdata, eeprom->offset, *data); + smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWDS_); + + /* Single byte write, according to man page */ + eeprom->len = 1; + + return ret; +} + +static struct ethtool_ops smsc911x_ethtool_ops = { + .get_settings = smsc911x_ethtool_getsettings, + .set_settings = smsc911x_ethtool_setsettings, + .get_link = ethtool_op_get_link, + .get_drvinfo = smsc911x_ethtool_getdrvinfo, + .nway_reset = smsc911x_ethtool_nwayreset, + .get_msglevel = smsc911x_ethtool_getmsglevel, + .set_msglevel = smsc911x_ethtool_setmsglevel, + .get_regs_len = smsc911x_ethtool_getregslen, + .get_regs = smsc911x_ethtool_getregs, + .get_eeprom_len = smsc911x_ethtool_get_eeprom_len, + .get_eeprom = smsc911x_ethtool_get_eeprom, + .set_eeprom = smsc911x_ethtool_set_eeprom, +}; + +/* Initializing private device structures, only called from probe */ +static int __devinit smsc911x_init(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int byte_test; + + SMSC_TRACE(PROBE, "Driver Parameters:"); + SMSC_TRACE(PROBE, "LAN base: 0x%08lX", + (unsigned long)pdata->ioaddr); + SMSC_TRACE(PROBE, "IRQ: %d", dev->irq); + SMSC_TRACE(PROBE, "PHY will be autodetected."); + +#if (!SMSC_CAN_USE_32BIT) + spin_lock_init(&pdata->dev_lock); +#endif + + if (pdata->ioaddr == 0) { + SMSC_WARNING(PROBE, "pdata->ioaddr: 0x00000000"); + return -ENODEV; + } + + /* Check byte ordering */ + byte_test = smsc911x_reg_read(pdata, BYTE_TEST); + SMSC_TRACE(PROBE, "BYTE_TEST: 0x%08X", byte_test); + if (byte_test == 0x43218765) { + SMSC_TRACE(PROBE, "BYTE_TEST looks swapped, " + "applying WORD_SWAP"); + smsc911x_reg_write(pdata, WORD_SWAP, 0xffffffff); + + /* 1 dummy read of BYTE_TEST is needed after a write to + * WORD_SWAP before its contents are valid */ + byte_test = smsc911x_reg_read(pdata, BYTE_TEST); + + byte_test = smsc911x_reg_read(pdata, BYTE_TEST); + } + + if (byte_test != 0x87654321) { + SMSC_WARNING(DRV, "BYTE_TEST: 0x%08X", byte_test); + if (((byte_test >> 16) & 0xFFFF) == (byte_test & 0xFFFF)) { + SMSC_WARNING(PROBE, + "top 16 bits equal to bottom 16 bits"); + SMSC_TRACE(PROBE, "This may mean the chip is set " + "for 32 bit while the bus is reading 16 bit"); + } + return -ENODEV; + } + + /* Default generation to zero (all workarounds apply) */ + pdata->generation = 0; + + pdata->idrev = smsc911x_reg_read(pdata, ID_REV); + switch (pdata->idrev & 0xFFFF0000) { + case 0x01180000: + case 0x01170000: + case 0x01160000: + case 0x01150000: + /* LAN911[5678] family */ + pdata->generation = pdata->idrev & 0x0000FFFF; + break; + + case 0x118A0000: + case 0x117A0000: + case 0x116A0000: + case 0x115A0000: + /* LAN921[5678] family */ + pdata->generation = 3; + break; + + case 0x92100000: + case 0x92110000: + case 0x92200000: + case 0x92210000: + /* LAN9210/LAN9211/LAN9220/LAN9221 */ + pdata->generation = 4; + break; + + default: + SMSC_WARNING(PROBE, "LAN911x not identified, idrev: 0x%08X", + pdata->idrev); + return -ENODEV; + } + + SMSC_TRACE(PROBE, "LAN911x identified, idrev: 0x%08X, generation: %d", + pdata->idrev, pdata->generation); + + if (pdata->generation == 0) + SMSC_WARNING(PROBE, + "This driver is not intended for this chip revision"); + + /* Reset the LAN911x */ + if (smsc911x_soft_reset(pdata)) + return -ENODEV; + + /* Disable all interrupt sources until we bring the device up */ + smsc911x_reg_write(pdata, INT_EN, 0); + + ether_setup(dev); + dev->open = smsc911x_open; + dev->stop = smsc911x_stop; + dev->hard_start_xmit = smsc911x_hard_start_xmit; + dev->get_stats = smsc911x_get_stats; + dev->set_multicast_list = smsc911x_set_multicast_list; + dev->flags |= IFF_MULTICAST; + dev->do_ioctl = smsc911x_do_ioctl; + netif_napi_add(dev, &pdata->napi, smsc911x_poll, SMSC_NAPI_WEIGHT); + dev->ethtool_ops = &smsc911x_ethtool_ops; + +#ifdef CONFIG_NET_POLL_CONTROLLER + dev->poll_controller = smsc911x_poll_controller; +#endif /* CONFIG_NET_POLL_CONTROLLER */ + + return 0; +} + +static int __devexit smsc911x_drv_remove(struct platform_device *pdev) +{ + struct net_device *dev; + struct smsc911x_data *pdata; + struct resource *res; + + dev = platform_get_drvdata(pdev); + BUG_ON(!dev); + pdata = netdev_priv(dev); + BUG_ON(!pdata); + BUG_ON(!pdata->ioaddr); + BUG_ON(!pdata->phy_dev); + + SMSC_TRACE(IFDOWN, "Stopping driver."); + + phy_disconnect(pdata->phy_dev); + pdata->phy_dev = NULL; + mdiobus_unregister(pdata->mii_bus); + mdiobus_free(pdata->mii_bus); + + platform_set_drvdata(pdev, NULL); + unregister_netdev(dev); + free_irq(dev->irq, dev); + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "smsc911x-memory"); + if (!res) + platform_get_resource(pdev, IORESOURCE_MEM, 0); + + release_mem_region(res->start, res->end - res->start); + + iounmap(pdata->ioaddr); + + free_netdev(dev); + + return 0; +} + +static int __devinit smsc911x_drv_probe(struct platform_device *pdev) +{ + struct net_device *dev; + struct smsc911x_data *pdata; + struct resource *res; + unsigned int intcfg = 0; + int res_size; + int retval; + DECLARE_MAC_BUF(mac); + + pr_info("%s: Driver version %s.\n", SMSC_CHIPNAME, SMSC_DRV_VERSION); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "smsc911x-memory"); + if (!res) + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + pr_warning("%s: Could not allocate resource.\n", + SMSC_CHIPNAME); + retval = -ENODEV; + goto out_0; + } + res_size = res->end - res->start; + + if (!request_mem_region(res->start, res_size, SMSC_CHIPNAME)) { + retval = -EBUSY; + goto out_0; + } + + dev = alloc_etherdev(sizeof(struct smsc911x_data)); + if (!dev) { + pr_warning("%s: Could not allocate device.\n", SMSC_CHIPNAME); + retval = -ENOMEM; + goto out_release_io_1; + } + + SET_NETDEV_DEV(dev, &pdev->dev); + + pdata = netdev_priv(dev); + + dev->irq = platform_get_irq(pdev, 0); + pdata->ioaddr = ioremap_nocache(res->start, res_size); + + /* copy config parameters across if present, otherwise pdata + * defaults to zeros */ + if (pdev->dev.platform_data) { + struct smsc911x_platform_config *config = + pdev->dev.platform_data; + pdata->irq_polarity = config->irq_polarity; + pdata->irq_type = config->irq_type; + pdata->phy_interface = config->phy_interface; + } + + pdata->dev = dev; + pdata->msg_enable = ((1 << debug) - 1); + + if (pdata->ioaddr == NULL) { + SMSC_WARNING(PROBE, + "Error smsc911x base address invalid"); + retval = -ENOMEM; + goto out_free_netdev_2; + } + + retval = smsc911x_init(dev); + if (retval < 0) + goto out_unmap_io_3; + + /* configure irq polarity and type before connecting isr */ + if (pdata->irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH) + intcfg |= INT_CFG_IRQ_POL_; + + if (pdata->irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL) + intcfg |= INT_CFG_IRQ_TYPE_; + + smsc911x_reg_write(pdata, INT_CFG, intcfg); + + /* Ensure interrupts are globally disabled before connecting ISR */ + smsc911x_reg_write(pdata, INT_EN, 0); + smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF); + + retval = request_irq(dev->irq, smsc911x_irqhandler, IRQF_DISABLED, + SMSC_CHIPNAME, dev); + if (retval) { + SMSC_WARNING(PROBE, + "Unable to claim requested irq: %d", dev->irq); + goto out_unmap_io_3; + } + + platform_set_drvdata(pdev, dev); + + retval = register_netdev(dev); + if (retval) { + SMSC_WARNING(PROBE, + "Error %i registering device", retval); + goto out_unset_drvdata_4; + } else { + SMSC_TRACE(PROBE, "Network interface: \"%s\"", dev->name); + } + + spin_lock_init(&pdata->mac_lock); + + retval = smsc911x_mii_init(pdev, dev); + if (retval) { + SMSC_WARNING(PROBE, + "Error %i initialising mii", retval); + goto out_unregister_netdev_5; + } + + spin_lock_irq(&pdata->mac_lock); + + /* Check if mac address has been specified when bringing interface up */ + if (is_valid_ether_addr(dev->dev_addr)) { + smsc911x_set_mac_address(pdata, dev->dev_addr); + SMSC_TRACE(PROBE, "MAC Address is specified by configuration"); + } else { + /* Try reading mac address from device. if EEPROM is present + * it will already have been set */ + u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH); + u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL); + dev->dev_addr[0] = (u8)(mac_low32); + dev->dev_addr[1] = (u8)(mac_low32 >> 8); + dev->dev_addr[2] = (u8)(mac_low32 >> 16); + dev->dev_addr[3] = (u8)(mac_low32 >> 24); + dev->dev_addr[4] = (u8)(mac_high16); + dev->dev_addr[5] = (u8)(mac_high16 >> 8); + + if (is_valid_ether_addr(dev->dev_addr)) { + /* eeprom values are valid so use them */ + SMSC_TRACE(PROBE, + "Mac Address is read from LAN911x EEPROM"); + } else { + /* eeprom values are invalid, generate random MAC */ + random_ether_addr(dev->dev_addr); + smsc911x_set_mac_address(pdata, dev->dev_addr); + SMSC_TRACE(PROBE, + "MAC Address is set to random_ether_addr"); + } + } + + spin_unlock_irq(&pdata->mac_lock); + + dev_info(&dev->dev, "MAC Address: %s\n", + print_mac(mac, dev->dev_addr)); + + return 0; + +out_unregister_netdev_5: + unregister_netdev(dev); +out_unset_drvdata_4: + platform_set_drvdata(pdev, NULL); + free_irq(dev->irq, dev); +out_unmap_io_3: + iounmap(pdata->ioaddr); +out_free_netdev_2: + free_netdev(dev); +out_release_io_1: + release_mem_region(res->start, res->end - res->start); +out_0: + return retval; +} + +static struct platform_driver smsc911x_driver = { + .probe = smsc911x_drv_probe, + .remove = smsc911x_drv_remove, + .driver = { + .name = SMSC_CHIPNAME, + }, +}; + +/* Entry point for loading the module */ +static int __init smsc911x_init_module(void) +{ + return platform_driver_register(&smsc911x_driver); +} + +/* entry point for unloading the module */ +static void __exit smsc911x_cleanup_module(void) +{ + platform_driver_unregister(&smsc911x_driver); +} + +module_init(smsc911x_init_module); +module_exit(smsc911x_cleanup_module); diff --git a/drivers/net/smsc911x.h b/drivers/net/smsc911x.h new file mode 100644 index 000000000000..feb36de274ca --- /dev/null +++ b/drivers/net/smsc911x.h @@ -0,0 +1,394 @@ +/*************************************************************************** + * + * Copyright (C) 2004-2008 SMSC + * Copyright (C) 2005-2008 ARM + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + ***************************************************************************/ +#ifndef __SMSC911X_H__ +#define __SMSC911X_H__ + +#define SMSC_CAN_USE_32BIT 1 +#define TX_FIFO_LOW_THRESHOLD ((u32)1600) +#define SMSC911X_EEPROM_SIZE ((u32)7) +#define USE_DEBUG 0 + +/* This is the maximum number of packets to be received every + * NAPI poll */ +#define SMSC_NAPI_WEIGHT 16 + +/* implements a PHY loopback test at initialisation time, to ensure a packet + * can be succesfully looped back */ +#define USE_PHY_WORK_AROUND + +#define DPRINTK(nlevel, klevel, fmt, args...) \ + ((void)((NETIF_MSG_##nlevel & pdata->msg_enable) && \ + printk(KERN_##klevel "%s: %s: " fmt "\n", \ + pdata->dev->name, __func__, ## args))) + +#if USE_DEBUG >= 1 +#define SMSC_WARNING(nlevel, fmt, args...) \ + DPRINTK(nlevel, WARNING, fmt, ## args) +#else +#define SMSC_WARNING(nlevel, fmt, args...) \ + ({ do {} while (0); 0; }) +#endif + +#if USE_DEBUG >= 2 +#define SMSC_TRACE(nlevel, fmt, args...) \ + DPRINTK(nlevel, INFO, fmt, ## args) +#else +#define SMSC_TRACE(nlevel, fmt, args...) \ + ({ do {} while (0); 0; }) +#endif + +#ifdef CONFIG_DEBUG_SPINLOCK +#define SMSC_ASSERT_MAC_LOCK(pdata) \ + WARN_ON(!spin_is_locked(&pdata->mac_lock)) +#else +#define SMSC_ASSERT_MAC_LOCK(pdata) do {} while (0) +#endif /* CONFIG_DEBUG_SPINLOCK */ + +#define FLOW_CTRL_TX (1) +#define FLOW_CTRL_RX (2) + +/* SMSC911x registers and bitfields */ +#define RX_DATA_FIFO 0x00 + +#define TX_DATA_FIFO 0x20 +#define TX_CMD_A_ON_COMP_ 0x80000000 +#define TX_CMD_A_BUF_END_ALGN_ 0x03000000 +#define TX_CMD_A_4_BYTE_ALGN_ 0x00000000 +#define TX_CMD_A_16_BYTE_ALGN_ 0x01000000 +#define TX_CMD_A_32_BYTE_ALGN_ 0x02000000 +#define TX_CMD_A_DATA_OFFSET_ 0x001F0000 +#define TX_CMD_A_FIRST_SEG_ 0x00002000 +#define TX_CMD_A_LAST_SEG_ 0x00001000 +#define TX_CMD_A_BUF_SIZE_ 0x000007FF +#define TX_CMD_B_PKT_TAG_ 0xFFFF0000 +#define TX_CMD_B_ADD_CRC_DISABLE_ 0x00002000 +#define TX_CMD_B_DISABLE_PADDING_ 0x00001000 +#define TX_CMD_B_PKT_BYTE_LENGTH_ 0x000007FF + +#define RX_STATUS_FIFO 0x40 +#define RX_STS_ES_ 0x00008000 +#define RX_STS_MCAST_ 0x00000400 + +#define RX_STATUS_FIFO_PEEK 0x44 + +#define TX_STATUS_FIFO 0x48 +#define TX_STS_ES_ 0x00008000 + +#define TX_STATUS_FIFO_PEEK 0x4C + +#define ID_REV 0x50 +#define ID_REV_CHIP_ID_ 0xFFFF0000 +#define ID_REV_REV_ID_ 0x0000FFFF + +#define INT_CFG 0x54 +#define INT_CFG_INT_DEAS_ 0xFF000000 +#define INT_CFG_INT_DEAS_CLR_ 0x00004000 +#define INT_CFG_INT_DEAS_STS_ 0x00002000 +#define INT_CFG_IRQ_INT_ 0x00001000 +#define INT_CFG_IRQ_EN_ 0x00000100 +#define INT_CFG_IRQ_POL_ 0x00000010 +#define INT_CFG_IRQ_TYPE_ 0x00000001 + +#define INT_STS 0x58 +#define INT_STS_SW_INT_ 0x80000000 +#define INT_STS_TXSTOP_INT_ 0x02000000 +#define INT_STS_RXSTOP_INT_ 0x01000000 +#define INT_STS_RXDFH_INT_ 0x00800000 +#define INT_STS_RXDF_INT_ 0x00400000 +#define INT_STS_TX_IOC_ 0x00200000 +#define INT_STS_RXD_INT_ 0x00100000 +#define INT_STS_GPT_INT_ 0x00080000 +#define INT_STS_PHY_INT_ 0x00040000 +#define INT_STS_PME_INT_ 0x00020000 +#define INT_STS_TXSO_ 0x00010000 +#define INT_STS_RWT_ 0x00008000 +#define INT_STS_RXE_ 0x00004000 +#define INT_STS_TXE_ 0x00002000 +#define INT_STS_TDFU_ 0x00000800 +#define INT_STS_TDFO_ 0x00000400 +#define INT_STS_TDFA_ 0x00000200 +#define INT_STS_TSFF_ 0x00000100 +#define INT_STS_TSFL_ 0x00000080 +#define INT_STS_RXDF_ 0x00000040 +#define INT_STS_RDFL_ 0x00000020 +#define INT_STS_RSFF_ 0x00000010 +#define INT_STS_RSFL_ 0x00000008 +#define INT_STS_GPIO2_INT_ 0x00000004 +#define INT_STS_GPIO1_INT_ 0x00000002 +#define INT_STS_GPIO0_INT_ 0x00000001 + +#define INT_EN 0x5C +#define INT_EN_SW_INT_EN_ 0x80000000 +#define INT_EN_TXSTOP_INT_EN_ 0x02000000 +#define INT_EN_RXSTOP_INT_EN_ 0x01000000 +#define INT_EN_RXDFH_INT_EN_ 0x00800000 +#define INT_EN_TIOC_INT_EN_ 0x00200000 +#define INT_EN_RXD_INT_EN_ 0x00100000 +#define INT_EN_GPT_INT_EN_ 0x00080000 +#define INT_EN_PHY_INT_EN_ 0x00040000 +#define INT_EN_PME_INT_EN_ 0x00020000 +#define INT_EN_TXSO_EN_ 0x00010000 +#define INT_EN_RWT_EN_ 0x00008000 +#define INT_EN_RXE_EN_ 0x00004000 +#define INT_EN_TXE_EN_ 0x00002000 +#define INT_EN_TDFU_EN_ 0x00000800 +#define INT_EN_TDFO_EN_ 0x00000400 +#define INT_EN_TDFA_EN_ 0x00000200 +#define INT_EN_TSFF_EN_ 0x00000100 +#define INT_EN_TSFL_EN_ 0x00000080 +#define INT_EN_RXDF_EN_ 0x00000040 +#define INT_EN_RDFL_EN_ 0x00000020 +#define INT_EN_RSFF_EN_ 0x00000010 +#define INT_EN_RSFL_EN_ 0x00000008 +#define INT_EN_GPIO2_INT_ 0x00000004 +#define INT_EN_GPIO1_INT_ 0x00000002 +#define INT_EN_GPIO0_INT_ 0x00000001 + +#define BYTE_TEST 0x64 + +#define FIFO_INT 0x68 +#define FIFO_INT_TX_AVAIL_LEVEL_ 0xFF000000 +#define FIFO_INT_TX_STS_LEVEL_ 0x00FF0000 +#define FIFO_INT_RX_AVAIL_LEVEL_ 0x0000FF00 +#define FIFO_INT_RX_STS_LEVEL_ 0x000000FF + +#define RX_CFG 0x6C +#define RX_CFG_RX_END_ALGN_ 0xC0000000 +#define RX_CFG_RX_END_ALGN4_ 0x00000000 +#define RX_CFG_RX_END_ALGN16_ 0x40000000 +#define RX_CFG_RX_END_ALGN32_ 0x80000000 +#define RX_CFG_RX_DMA_CNT_ 0x0FFF0000 +#define RX_CFG_RX_DUMP_ 0x00008000 +#define RX_CFG_RXDOFF_ 0x00001F00 + +#define TX_CFG 0x70 +#define TX_CFG_TXS_DUMP_ 0x00008000 +#define TX_CFG_TXD_DUMP_ 0x00004000 +#define TX_CFG_TXSAO_ 0x00000004 +#define TX_CFG_TX_ON_ 0x00000002 +#define TX_CFG_STOP_TX_ 0x00000001 + +#define HW_CFG 0x74 +#define HW_CFG_TTM_ 0x00200000 +#define HW_CFG_SF_ 0x00100000 +#define HW_CFG_TX_FIF_SZ_ 0x000F0000 +#define HW_CFG_TR_ 0x00003000 +#define HW_CFG_SRST_ 0x00000001 + +/* only available on 115/117 */ +#define HW_CFG_PHY_CLK_SEL_ 0x00000060 +#define HW_CFG_PHY_CLK_SEL_INT_PHY_ 0x00000000 +#define HW_CFG_PHY_CLK_SEL_EXT_PHY_ 0x00000020 +#define HW_CFG_PHY_CLK_SEL_CLK_DIS_ 0x00000040 +#define HW_CFG_SMI_SEL_ 0x00000010 +#define HW_CFG_EXT_PHY_DET_ 0x00000008 +#define HW_CFG_EXT_PHY_EN_ 0x00000004 +#define HW_CFG_SRST_TO_ 0x00000002 + +/* only available on 116/118 */ +#define HW_CFG_32_16_BIT_MODE_ 0x00000004 + +#define RX_DP_CTRL 0x78 +#define RX_DP_CTRL_RX_FFWD_ 0x80000000 + +#define RX_FIFO_INF 0x7C +#define RX_FIFO_INF_RXSUSED_ 0x00FF0000 +#define RX_FIFO_INF_RXDUSED_ 0x0000FFFF + +#define TX_FIFO_INF 0x80 +#define TX_FIFO_INF_TSUSED_ 0x00FF0000 +#define TX_FIFO_INF_TDFREE_ 0x0000FFFF + +#define PMT_CTRL 0x84 +#define PMT_CTRL_PM_MODE_ 0x00003000 +#define PMT_CTRL_PM_MODE_D0_ 0x00000000 +#define PMT_CTRL_PM_MODE_D1_ 0x00001000 +#define PMT_CTRL_PM_MODE_D2_ 0x00002000 +#define PMT_CTRL_PM_MODE_D3_ 0x00003000 +#define PMT_CTRL_PHY_RST_ 0x00000400 +#define PMT_CTRL_WOL_EN_ 0x00000200 +#define PMT_CTRL_ED_EN_ 0x00000100 +#define PMT_CTRL_PME_TYPE_ 0x00000040 +#define PMT_CTRL_WUPS_ 0x00000030 +#define PMT_CTRL_WUPS_NOWAKE_ 0x00000000 +#define PMT_CTRL_WUPS_ED_ 0x00000010 +#define PMT_CTRL_WUPS_WOL_ 0x00000020 +#define PMT_CTRL_WUPS_MULTI_ 0x00000030 +#define PMT_CTRL_PME_IND_ 0x00000008 +#define PMT_CTRL_PME_POL_ 0x00000004 +#define PMT_CTRL_PME_EN_ 0x00000002 +#define PMT_CTRL_READY_ 0x00000001 + +#define GPIO_CFG 0x88 +#define GPIO_CFG_LED3_EN_ 0x40000000 +#define GPIO_CFG_LED2_EN_ 0x20000000 +#define GPIO_CFG_LED1_EN_ 0x10000000 +#define GPIO_CFG_GPIO2_INT_POL_ 0x04000000 +#define GPIO_CFG_GPIO1_INT_POL_ 0x02000000 +#define GPIO_CFG_GPIO0_INT_POL_ 0x01000000 +#define GPIO_CFG_EEPR_EN_ 0x00700000 +#define GPIO_CFG_GPIOBUF2_ 0x00040000 +#define GPIO_CFG_GPIOBUF1_ 0x00020000 +#define GPIO_CFG_GPIOBUF0_ 0x00010000 +#define GPIO_CFG_GPIODIR2_ 0x00000400 +#define GPIO_CFG_GPIODIR1_ 0x00000200 +#define GPIO_CFG_GPIODIR0_ 0x00000100 +#define GPIO_CFG_GPIOD4_ 0x00000020 +#define GPIO_CFG_GPIOD3_ 0x00000010 +#define GPIO_CFG_GPIOD2_ 0x00000004 +#define GPIO_CFG_GPIOD1_ 0x00000002 +#define GPIO_CFG_GPIOD0_ 0x00000001 + +#define GPT_CFG 0x8C +#define GPT_CFG_TIMER_EN_ 0x20000000 +#define GPT_CFG_GPT_LOAD_ 0x0000FFFF + +#define GPT_CNT 0x90 +#define GPT_CNT_GPT_CNT_ 0x0000FFFF + +#define WORD_SWAP 0x98 + +#define FREE_RUN 0x9C + +#define RX_DROP 0xA0 + +#define MAC_CSR_CMD 0xA4 +#define MAC_CSR_CMD_CSR_BUSY_ 0x80000000 +#define MAC_CSR_CMD_R_NOT_W_ 0x40000000 +#define MAC_CSR_CMD_CSR_ADDR_ 0x000000FF + +#define MAC_CSR_DATA 0xA8 + +#define AFC_CFG 0xAC +#define AFC_CFG_AFC_HI_ 0x00FF0000 +#define AFC_CFG_AFC_LO_ 0x0000FF00 +#define AFC_CFG_BACK_DUR_ 0x000000F0 +#define AFC_CFG_FCMULT_ 0x00000008 +#define AFC_CFG_FCBRD_ 0x00000004 +#define AFC_CFG_FCADD_ 0x00000002 +#define AFC_CFG_FCANY_ 0x00000001 + +#define E2P_CMD 0xB0 +#define E2P_CMD_EPC_BUSY_ 0x80000000 +#define E2P_CMD_EPC_CMD_ 0x70000000 +#define E2P_CMD_EPC_CMD_READ_ 0x00000000 +#define E2P_CMD_EPC_CMD_EWDS_ 0x10000000 +#define E2P_CMD_EPC_CMD_EWEN_ 0x20000000 +#define E2P_CMD_EPC_CMD_WRITE_ 0x30000000 +#define E2P_CMD_EPC_CMD_WRAL_ 0x40000000 +#define E2P_CMD_EPC_CMD_ERASE_ 0x50000000 +#define E2P_CMD_EPC_CMD_ERAL_ 0x60000000 +#define E2P_CMD_EPC_CMD_RELOAD_ 0x70000000 +#define E2P_CMD_EPC_TIMEOUT_ 0x00000200 +#define E2P_CMD_MAC_ADDR_LOADED_ 0x00000100 +#define E2P_CMD_EPC_ADDR_ 0x000000FF + +#define E2P_DATA 0xB4 +#define E2P_DATA_EEPROM_DATA_ 0x000000FF +#define LAN_REGISTER_EXTENT 0x00000100 + +/* + * MAC Control and Status Register (Indirect Address) + * Offset (through the MAC_CSR CMD and DATA port) + */ +#define MAC_CR 0x01 +#define MAC_CR_RXALL_ 0x80000000 +#define MAC_CR_HBDIS_ 0x10000000 +#define MAC_CR_RCVOWN_ 0x00800000 +#define MAC_CR_LOOPBK_ 0x00200000 +#define MAC_CR_FDPX_ 0x00100000 +#define MAC_CR_MCPAS_ 0x00080000 +#define MAC_CR_PRMS_ 0x00040000 +#define MAC_CR_INVFILT_ 0x00020000 +#define MAC_CR_PASSBAD_ 0x00010000 +#define MAC_CR_HFILT_ 0x00008000 +#define MAC_CR_HPFILT_ 0x00002000 +#define MAC_CR_LCOLL_ 0x00001000 +#define MAC_CR_BCAST_ 0x00000800 +#define MAC_CR_DISRTY_ 0x00000400 +#define MAC_CR_PADSTR_ 0x00000100 +#define MAC_CR_BOLMT_MASK_ 0x000000C0 +#define MAC_CR_DFCHK_ 0x00000020 +#define MAC_CR_TXEN_ 0x00000008 +#define MAC_CR_RXEN_ 0x00000004 + +#define ADDRH 0x02 + +#define ADDRL 0x03 + +#define HASHH 0x04 + +#define HASHL 0x05 + +#define MII_ACC 0x06 +#define MII_ACC_PHY_ADDR_ 0x0000F800 +#define MII_ACC_MIIRINDA_ 0x000007C0 +#define MII_ACC_MII_WRITE_ 0x00000002 +#define MII_ACC_MII_BUSY_ 0x00000001 + +#define MII_DATA 0x07 + +#define FLOW 0x08 +#define FLOW_FCPT_ 0xFFFF0000 +#define FLOW_FCPASS_ 0x00000004 +#define FLOW_FCEN_ 0x00000002 +#define FLOW_FCBSY_ 0x00000001 + +#define VLAN1 0x09 + +#define VLAN2 0x0A + +#define WUFF 0x0B + +#define WUCSR 0x0C +#define WUCSR_GUE_ 0x00000200 +#define WUCSR_WUFR_ 0x00000040 +#define WUCSR_MPR_ 0x00000020 +#define WUCSR_WAKE_EN_ 0x00000004 +#define WUCSR_MPEN_ 0x00000002 + +/* + * Phy definitions (vendor-specific) + */ +#define LAN9118_PHY_ID 0x00C0001C + +#define MII_INTSTS 0x1D + +#define MII_INTMSK 0x1E +#define PHY_INTMSK_AN_RCV_ (1 << 1) +#define PHY_INTMSK_PDFAULT_ (1 << 2) +#define PHY_INTMSK_AN_ACK_ (1 << 3) +#define PHY_INTMSK_LNKDOWN_ (1 << 4) +#define PHY_INTMSK_RFAULT_ (1 << 5) +#define PHY_INTMSK_AN_COMP_ (1 << 6) +#define PHY_INTMSK_ENERGYON_ (1 << 7) +#define PHY_INTMSK_DEFAULT_ (PHY_INTMSK_ENERGYON_ | \ + PHY_INTMSK_AN_COMP_ | \ + PHY_INTMSK_RFAULT_ | \ + PHY_INTMSK_LNKDOWN_) + +#define ADVERTISE_PAUSE_ALL (ADVERTISE_PAUSE_CAP | \ + ADVERTISE_PAUSE_ASYM) + +#define LPA_PAUSE_ALL (LPA_PAUSE_CAP | \ + LPA_PAUSE_ASYM) + +#endif /* __SMSC911X_H__ */ diff --git a/include/linux/smsc911x.h b/include/linux/smsc911x.h new file mode 100644 index 000000000000..47c4ffd10dbb --- /dev/null +++ b/include/linux/smsc911x.h @@ -0,0 +1,42 @@ +/*************************************************************************** + * + * Copyright (C) 2004-2008 SMSC + * Copyright (C) 2005-2008 ARM + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + ***************************************************************************/ +#ifndef __LINUX_SMSC911X_H__ +#define __LINUX_SMSC911X_H__ + +#include + +/* platform_device configuration data, should be assigned to + * the platform_device's dev.platform_data */ +struct smsc911x_platform_config { + unsigned int irq_polarity; + unsigned int irq_type; + phy_interface_t phy_interface; +}; + +/* Constants for platform_device irq polarity configuration */ +#define SMSC911X_IRQ_POLARITY_ACTIVE_LOW 0 +#define SMSC911X_IRQ_POLARITY_ACTIVE_HIGH 1 + +/* Constants for platform_device irq type configuration */ +#define SMSC911X_IRQ_TYPE_OPEN_DRAIN 0 +#define SMSC911X_IRQ_TYPE_PUSH_PULL 1 + +#endif /* __LINUX_SMSC911X_H__ */ -- cgit v1.2.1