| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
| |
Patch from Lennert Buytenhek
The intel docs call it IXP2000_PRODUCT_ID, and we have a definition
for IXP2000_PRODUCT_ID as well, so IXP2000_PROD_ID can go. It's only
used in one place.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch from Lennert Buytenhek
This patch:
- changes the ixp2000_reg_write accessor to take a 'volatile void *'
instead of a 'volatile unsigned long *', which then allows passing in
a u32 * as first argument without being greeted with a warning; and
- adds an ixp2000_reg_read accessor.
We can then use these accessors in ixp2000 code to access on-chip
peripherals, instead of directly dereferencing pointers. This is for
use by the ixp2000 microengine driver which was recently announced on
netdev. We can't use readl/writel on the ixp2000 since it is usually
run in big-endian mode, and on big-endian platforms, readl/writel
perform byteswapping.
A future patch will remove the readback from ixp2000_reg_write, since
it's not needed to prevent erratum #66, and add manual readbacks to the
places that need them (writes are not synchronous since we map in device
space using XCB=101 nowadays), such as interrupt disabling and GPIO
manipulation. See also:
http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2005-February/027084.html
Patch has been ACKed by Jeff Garzik.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
| |
Patch from Lennert Buytenhek
This patch converts the ixp2000 serial port over to a platform
serial device.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Patch from Lennert Buytenhek
This patch cleans up the ixp2000 gpio irq code and implements the
set_irq_type method for gpio irqs so that users can select for which
events (falling edge/rising edge/level low/level high) on the gpio
pin they want the corresponding gpio irq to be triggered.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
| |
Patch from Lennert Buytenhek
Export ixp2000_pci_config_addr, to be used by the IXDP2800 platform
setup code to coordinate booting the master and slave NPU.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
