summaryrefslogtreecommitdiffstats
path: root/drivers/scsi
Commit message (Collapse)AuthorAgeFilesLines
* qla2xxx: Fix stale pointer access.Quinn Tran2016-03-035-9/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit cb43285ff7039fe3c4b0bc476e6d6569c31104f3 upstream. [ Upstream Commit 84e32a06f4f8756ce9ec3c8dc7e97896575f0771 ] Commit 84e32a0 ("qla2xxx: Use pci_enable_msix_range() instead of pci_enable_msix()") introduced a regression when target mode is enabled. In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set to a value higher than the number of response queues allocated causing an invalid dereference. Specifically here in qla2x00_init_rings(): *rsp->in_ptr = 0; Add additional check to make sure the pointer is valid. following call stack will be seen ---- 8< ---- RIP: 0010:[<ffffffffa02ccadc>] [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx] RSP: 0018:ffff880429447dd8 EFLAGS: 00010082 .... Call Trace: [<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx] [<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx] [<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx] [<ffffffff8107d2c9>] kthread+0xc9/0xe0 [<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90 [<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70 [<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90 ---- 8< ---- Signed-off-by: Quinn Tran <quinn.tran@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* sd: Optimal I/O size is in bytes, not sectorsMartin K. Petersen2016-03-031-1/+1
| | | | | | | | | | | | | | | | | | commit d0eb20a863ba7dc1d3f4b841639671f134560be2 upstream. Commit ca369d51b3e1 ("block/sd: Fix device-imposed transfer length limits") accidentally switched optimal I/O size reporting from bytes to block layer sectors. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Fixes: ca369d51b3e1649be4a72addd6d6a168cfb3f537 Reviewed-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* scsi: fix soft lockup in scsi_remove_target() on module removalJames Bottomley2016-02-251-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 90a88d6ef88edcfc4f644dddc7eef4ea41bccf8b upstream. This softlockup is currently happening: [ 444.088002] NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [kworker/1:1:29] [ 444.088002] Modules linked in: lpfc(-) qla2x00tgt(O) qla2xxx_scst(O) scst_vdisk(O) scsi_transport_fc libcrc32c scst(O) dlm configfs nfsd lockd grace nfs_acl auth_rpcgss sunrpc ed d snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device dm_mod iTCO_wdt snd_hda_codec_realtek snd_hda_codec_generic gpio_ich iTCO_vendor_support ppdev snd_hda_intel snd_hda_codec snd_hda _core snd_hwdep tg3 snd_pcm snd_timer libphy lpc_ich parport_pc ptp acpi_cpufreq snd pps_core fjes parport i2c_i801 ehci_pci tpm_tis tpm sr_mod cdrom soundcore floppy hwmon sg 8250_ fintek pcspkr i915 drm_kms_helper uhci_hcd ehci_hcd drm fb_sys_fops sysimgblt sysfillrect syscopyarea i2c_algo_bit usbcore button video usb_common fan ata_generic ata_piix libata th ermal [ 444.088002] CPU: 1 PID: 29 Comm: kworker/1:1 Tainted: G O 4.4.0-rc5-2.g1e923a3-default #1 [ 444.088002] Hardware name: FUJITSU SIEMENS ESPRIMO E /D2164-A1, BIOS 5.00 R1.10.2164.A1 05/08/2006 [ 444.088002] Workqueue: fc_wq_4 fc_rport_final_delete [scsi_transport_fc] [ 444.088002] task: f6266ec0 ti: f6268000 task.ti: f6268000 [ 444.088002] EIP: 0060:[<c07e7044>] EFLAGS: 00000286 CPU: 1 [ 444.088002] EIP is at _raw_spin_unlock_irqrestore+0x14/0x20 [ 444.088002] EAX: 00000286 EBX: f20d3800 ECX: 00000002 EDX: 00000286 [ 444.088002] ESI: f50ba800 EDI: f2146848 EBP: f6269ec8 ESP: f6269ec8 [ 444.088002] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 444.088002] CR0: 8005003b CR2: 08f96600 CR3: 363ae000 CR4: 000006d0 [ 444.088002] Stack: [ 444.088002] f6269eec c066b0f7 00000286 f2146848 f50ba808 f50ba800 f50ba800 f2146a90 [ 444.088002] f2146848 f6269f08 f8f0a4ed f3141000 f2146800 f2146a90 f619fa00 00000040 [ 444.088002] f6269f40 c026cb25 00000001 166c6392 00000061 f6757140 f6136340 00000004 [ 444.088002] Call Trace: [ 444.088002] [<c066b0f7>] scsi_remove_target+0x167/0x1c0 [ 444.088002] [<f8f0a4ed>] fc_rport_final_delete+0x9d/0x1e0 [scsi_transport_fc] [ 444.088002] [<c026cb25>] process_one_work+0x155/0x3e0 [ 444.088002] [<c026cde7>] worker_thread+0x37/0x490 [ 444.088002] [<c027214b>] kthread+0x9b/0xb0 [ 444.088002] [<c07e72c1>] ret_from_kernel_thread+0x21/0x40 What appears to be happening is that something has pinned the target so it can't go into STARGET_DEL via final release and the loop in scsi_remove_target spins endlessly until that happens. The fix for this soft lockup is to not keep looping over a device that we've called remove on but which hasn't gone into DEL state. This patch will retain a simplistic memory of the last target and not keep looping over it. Reported-by: Sebastian Herbszt <herbszt@gmx.de> Tested-by: Sebastian Herbszt <herbszt@gmx.de> Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38 Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* SCSI: Add Marvell Console to VPD blacklistMika Westerberg2016-02-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 82c43310508eb19eb41fe7862e89afeb74030b84 upstream. I have a Marvell 88SE9230 SATA Controller that has some sort of integrated console SCSI device attached to one of the ports. ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata14.00: ATAPI: MARVELL VIRTUALL, 1.09, max UDMA/66 ata14.00: configured for UDMA/66 scsi 13:0:0:0: Processor Marvell Console 1.01 PQ: 0 ANSI: 5 Sending it VPD INQUIRY command seem to always fail with following error: ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 ata14.00: irq_stat 0x40000001 ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 2 dma 16640 in Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation) ata14: hard resetting link This has been minor annoyance (only error printed on dmesg) until commit 09e2b0b14690 ("scsi: rescan VPD attributes") added call to scsi_attach_vpd() in scsi_rescan_device(). The commit causes the system to splat out following errors continuously without ever reaching the UI: ata14.00: configured for UDMA/66 ata14: EH complete ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 ata14.00: irq_stat 0x40000001 ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 6 dma 16640 in Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation) ata14: hard resetting link ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata14.00: configured for UDMA/66 ata14: EH complete ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 ata14.00: irq_stat 0x40000001 ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 7 dma 16640 in Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation) Without in-depth understanding of SCSI layer and the Marvell controller, I suspect this happens because when the link goes down (because of an error) we schedule scsi_rescan_device() which again fails to read VPD data... ad infinitum. Since VPD data cannot be read from the device anyway we prevent the SCSI layer from even trying by blacklisting the device. This gets away the error and the system starts up normally. [mkp: Widened the match to all revisions of this device] Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* scsi_dh_rdac: always retry MODE SELECT on command lock violationHannes Reinecke2016-02-251-1/+3
| | | | | | | | | | | | | | | | commit d2d06d4fe0f2cc2df9b17fefec96e6e1a1271d91 upstream. If MODE SELECT returns with sense '05/91/36' (command lock violation) it should always be retried without counting the number of retries. During an HBA upgrade or similar circumstances one might see a flood of MODE SELECT command from various HBAs, which will easily trigger the sense code and exceed the retry count. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drivers/scsi/sg.c: mark VMA as VM_IO to prevent migrationKirill A. Shutemov2016-02-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 461c7fa126794157484dca48e88effa4963e3af3 upstream. Reduced testcase: #include <fcntl.h> #include <unistd.h> #include <sys/mman.h> #include <numaif.h> #define SIZE 0x2000 int main() { int fd; void *p; fd = open("/dev/sg0", O_RDWR); p = mmap(NULL, SIZE, PROT_EXEC, MAP_PRIVATE | MAP_LOCKED, fd, 0); mbind(p, SIZE, 0, NULL, 0, MPOL_MF_MOVE); return 0; } We shouldn't try to migrate pages in sg VMA as we don't have a way to update Sg_scatter_hold::pages accordingly from mm core. Let's mark the VMA as VM_IO to indicate to mm core that the VMA is not migratable. Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Doug Gilbert <dgilbert@interlog.com> Cc: David Rientjes <rientjes@google.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Shiraz Hashim <shashim@codeaurora.org> Cc: Hugh Dickins <hughd@google.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: syzkaller <syzkaller@googlegroups.com> Cc: Kostya Serebryany <kcc@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* SCSI: fix crashes in sd and sr runtime PMAlan Stern2016-02-252-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 13b4389143413a1f18127c07f72c74cad5b563e8 upstream. Runtime suspend during driver probe and removal can cause problems. The driver's runtime_suspend or runtime_resume callbacks may invoked before the driver has finished binding to the device or after the driver has unbound from the device. This problem shows up with the sd and sr drivers, and can cause disk or CD/DVD drives to become unusable as a result. The fix is simple. The drivers store a pointer to the scsi_disk or scsi_cd structure as their private device data when probing is finished, so we simply have to be sure to clear the private data during removal and test it during runtime suspend/resume. This fixes <https://bugs.debian.org/801925>. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Paul Menzel <paul.menzel@giantmonkey.de> Reported-by: Erich Schubert <erich@debian.org> Reported-by: Alexandre Rossi <alexandre.rossi@gmail.com> Tested-by: Paul Menzel <paul.menzel@giantmonkey.de> Tested-by: Erich Schubert <erich@debian.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* scsi: add Synology to 1024 sector blacklistMike Christie2016-02-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 9055082fb100cc66e20c048251d05159f5f2cfba upstream. Another iscsi target that cannot handle large IOs, but does not tell us a limit. The Synology iSCSI targets report: Block limits VPD page (SBC): Write same no zero (WSNZ): 0 Maximum compare and write length: 0 blocks Optimal transfer length granularity: 0 blocks Maximum transfer length: 0 blocks Optimal transfer length: 0 blocks Maximum prefetch length: 0 blocks Maximum unmap LBA count: 0 Maximum unmap block descriptor count: 0 Optimal unmap granularity: 0 Unmap granularity alignment valid: 0 Unmap granularity alignment: 0 Maximum write same length: 0x0 blocks and the size of the command it can handle seems to depend on how much memory it can allocate at the time. This results in IO errors when handling large IOs. This patch just has us use the old 1024 default sectors for this target by adding it to the scsi blacklist. We do not have good contacs with this vendors, so I have not been able to try and fix on their side. I have posted this a long while back, but it was not merged. This version just fixes it up for merge/patch failures in the original version. Reported-by: Ancoron Luciferis <ancoron.luciferis@googlemail.com> Reported-by: Michael Meyers <steltek@tcnnet.com> Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge remote-tracking branch 'mkp-scsi/4.4/scsi-fixes' into fixesJames Bottomley2015-12-281-3/+6
|\
| * sd: Reject optimal transfer length smaller than page sizeMartin K. Petersen2015-12-211-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Eryu Guan reported that loading scsi_debug would fail. This turned out to be caused by scsi_debug reporting an optimal I/O size of 32KB which is smaller than the 64KB page size on the PowerPC system in question. Add a check to ensure that we only use the device-reported OPTIMAL TRANSFER LENGTH if it is bigger than or equal to the page cache size. Reported-by: Eryu Guan <guaneryu@gmail.com> Reported-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | Merge remote-tracking branch 'mkp-scsi/4.4/scsi-fixes' into fixesJames Bottomley2015-12-171-10/+10
|\|
| * Revert "SCSI: Fix NULL pointer dereference in runtime PM"Ken Xue2015-12-101-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 49718f0fb8c9 ("SCSI: Fix NULL pointer dereference in runtime PM") The old commit may lead to a issue that blk_{pre|post}_runtime_suspend and blk_{pre|post}_runtime_resume may not be called in pairs. Take sr device as example, when sr device goes to runtime suspend, blk_{pre|post}_runtime_suspend will be called since sr device defined pm->runtime_suspend. But blk_{pre|post}_runtime_resume will not be called since sr device doesn't have pm->runtime_resume. so, sr device can not resume correctly anymore. More discussion can be found from below link. http://marc.info/?l=linux-scsi&m=144163730531875&w=2 Signed-off-by: Ken Xue <Ken.Xue@amd.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: Xiangliang Yu <Xiangliang.Yu@amd.com> Cc: James E.J. Bottomley <JBottomley@odin.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Michael Terry <Michael.terry@canonical.com> Cc: stable@vger.kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | ses: fix additional element traversal bugJames Bottomley2015-12-111-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | KASAN found that our additional element processing scripts drop off the end of the VPD page into unallocated space. The reason is that not every element has additional information but our traversal routines think they do, leading to them expecting far more additional information than is present. Fix this by adding a gate to the traversal routine so that it only processes elements that are expected to have additional information (list is in SES-2 section 6.1.13.1: Additional Element Status diagnostic page overview) Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* | ses: Fix problems with simple enclosuresJames Bottomley2015-12-101-1/+19
|/ | | | | | | | | | | | | | | | | | Simple enclosure implementations (mostly USB) are allowed to return only page 8 to every diagnostic query. That really confuses our implementation because we assume the return is the page we asked for and end up doing incorrect offsets based on bogus information leading to accesses outside of allocated ranges. Fix that by checking the page code of the return and giving an error if it isn't the one we asked for. This should fix reported bugs with USB storage by simply refusing to attach to enclosures that behave like this. It's also good defensive practise now that we're starting to see more USB enclosures. Reported-by: Andrea Gelmini <andrea.gelmini@gelma.net> Cc: stable@vger.kernel.org Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* Merge tag 'scsi-fixes' of ↵Linus Torvalds2015-12-0614-48/+103
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "This is quite a bumper crop of fixes: three from Arnd correcting various build issues in some configurations, a lock recursion in qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a potential null deref in st, a revert of a bdi registration fix that turned out to cause even more problems, a set of fixes to allow people who only defined MPT2SAS to still work after the mpt2/mpt3sas merger and a couple of fixes for issues turned up by the hyper-v storvsc driver" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility Revert "scsi: Fix a bdi reregistration race" mpt3sas: Add dummy Kconfig option for backwards compatibility Fix a memory leak in scsi_host_dev_release() block/sd: Fix device-imposed transfer length limits scsi_debug: fix prevent_allow+verify regressions MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem. sd: Make discard granularity match logical block size when LBPRZ=1 scsi: hpsa: select CONFIG_SCSI_SAS_ATTR scsi: advansys needs ISA dma api for ISA support scsi_sysfs: protect against double execution of __scsi_remove_device() st: fix potential null pointer dereference. scsi: report 'INQUIRY result too short' once per host advansys: fix big-endian builds qla2xxx: Fix rwlock recursion hpsa: logical vs bitwise AND typo mvsas: don't allow negative timeouts mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
| * Merge branch 'mkp-fixes' into fixesJames Bottomley2015-12-0314-37/+100
| |\
| | * mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibilityJames Bottomley2015-12-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The non-PCI builds of the O day test project are failing: On Thu, 2015-12-03 at 05:02 +0800, kbuild test robot wrote: > warning: (SCSI_MPT2SAS) selects SCSI_MPT3SAS which has unmet direct > dependencies (SCSI_LOWLEVEL && PCI && SCSI) The problem is that select and depend don't interact because Kconfig doesn't have a SAT solver, so depend picks up dependencies and select does onward selects, but select doesn't pick up dependencies. To fix this, we need to add the correct dependencies to the MPT2SAS option like this. Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: b840c3627b6f4f856b333a14a72f8ed86da2f86c Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
| | * mpt3sas: Add dummy Kconfig option for backwards compatibilityMartin K. Petersen2015-11-301-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The mpt2sas driver was recently folded into mpt3sas to reduce code duplication. To avoid problems for people that only have CONFIG_SCSI_MPT2SAS in their .config we introduce a dummy option that will select MPT3SAS if MPT2SAS was previously enabled. This is a temporary measure and we will deprecate this config option in 4.6. Reported-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Christoph Hellwig <hch@lst.de> Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com> CC: Ingo Molnar <mingo@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * Fix a memory leak in scsi_host_dev_release()Bart Van Assche2015-11-301-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Avoid that kmemleak reports the following memory leak if a SCSI LLD calls scsi_host_alloc() and scsi_host_put() but neither scsi_host_add() nor scsi_host_remove(). The following shell command triggers that scenario: for ((i=0; i<2; i++)); do srp_daemon -oac | while read line; do echo $line >/sys/class/infiniband_srp/srp-mlx4_0-1/add_target done done unreferenced object 0xffff88021b24a220 (size 8): comm "srp_daemon", pid 56421, jiffies 4295006762 (age 4240.750s) hex dump (first 8 bytes): 68 6f 73 74 35 38 00 a5 host58.. backtrace: [<ffffffff8151014a>] kmemleak_alloc+0x7a/0xc0 [<ffffffff81165c1e>] __kmalloc_track_caller+0xfe/0x160 [<ffffffff81260d2b>] kvasprintf+0x5b/0x90 [<ffffffff81260e2d>] kvasprintf_const+0x8d/0xb0 [<ffffffff81254b0c>] kobject_set_name_vargs+0x3c/0xa0 [<ffffffff81337e3c>] dev_set_name+0x3c/0x40 [<ffffffff81355757>] scsi_host_alloc+0x327/0x4b0 [<ffffffffa03edc8e>] srp_create_target+0x4e/0x8a0 [ib_srp] [<ffffffff8133778b>] dev_attr_store+0x1b/0x20 [<ffffffff811f27fa>] sysfs_kf_write+0x4a/0x60 [<ffffffff811f1e8e>] kernfs_fop_write+0x14e/0x180 [<ffffffff81176eef>] __vfs_write+0x2f/0xf0 [<ffffffff811771e4>] vfs_write+0xa4/0x100 [<ffffffff81177c64>] SyS_write+0x54/0xc0 [<ffffffff8151b257>] entry_SYSCALL_64_fastpath+0x12/0x6f Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * block/sd: Fix device-imposed transfer length limitsMartin K. Petersen2015-11-252-16/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 4f258a46346c ("sd: Fix maximum I/O size for BLOCK_PC requests") had the unfortunate side-effect of removing an implicit clamp to BLK_DEF_MAX_SECTORS for REQ_TYPE_FS requests in the block layer code. This caused problems for some SMR drives. Debugging this issue revealed a few problems with the existing infrastructure since the block layer didn't know how to deal with device-imposed limits, only limits set by the I/O controller. - Introduce a new queue limit, max_dev_sectors, which is used by the ULD to signal the maximum sectors for a REQ_TYPE_FS request. - Ensure that max_dev_sectors is correctly stacked and taken into account when overriding max_sectors through sysfs. - Rework sd_read_block_limits() so it saves the max_xfer and opt_xfer values for later processing. - In sd_revalidate() set the queue's max_dev_sectors based on the MAXIMUM TRANSFER LENGTH value in the Block Limits VPD. If this value is not reported, fall back to a cap based on the CDB TRANSFER LENGTH field size. - In sd_revalidate(), use OPTIMAL TRANSFER LENGTH from the Block Limits VPD--if reported and sane--to signal the preferred device transfer size for FS requests. Otherwise use BLK_DEF_MAX_SECTORS. - blk_limits_max_hw_sectors() is no longer used and can be removed. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93581 Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: sweeneygj@gmx.com Tested-by: Arzeets <anatol.pomozov@gmail.com> Tested-by: David Eisner <david.eisner@oriel.oxon.org> Tested-by: Mario Kicherer <dev@kicherer.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * scsi_debug: fix prevent_allow+verify regressionsDouglas Gilbert2015-11-251-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ruediger Meier observed a regression with the PREVENT ALLOW MEDIUM REMOVAL command in lk 3.19: http://www.spinics.net/lists/util-linux-ng/msg11448.html Inspection indicated the same regression with VERIFY(10). The patch is against lk 3.19.3 and also works with lk 4.3.0 . With this patch both commands are accepted and do nothing. ChangeLog: - fix the lk 3.19 regression so that the PREVENT ALLOW MEDIUM REMOVAL command is supported once again - same fix for VERIFY(10) Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Hannes Reinicke <hare@suse.de> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * sd: Make discard granularity match logical block size when LBPRZ=1Martin K. Petersen2015-11-251-5/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A device may report an OPTIMAL UNMAP GRANULARITY and UNMAP GRANULARITY ALIGNMENT in the Block Limits VPD. These parameters describe the device's internal provisioning allocation units. By default the block layer will round and align any discard requests based on these limits. If a device reports LBPRZ=1 to guarantee zeroes after discard, however, it is imperative that the block layer does not leave out any parts of the requested block range. Otherwise the device can not do the required zeroing of any partial allocation units and this can lead to data corruption. Since the dm thinp personality relies on the block layer's current behavior and is unable to deal with partial discard blocks we work around the problem by setting the granularity to match the logical block size when LBPRZ is enabled. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * scsi: hpsa: select CONFIG_SCSI_SAS_ATTRArnd Bergmann2015-11-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The hpsa driver recently started using the sas transport class, but it does not ensure that the corresponding code is actually built, which may lead to a link error: drivers/built-in.o: In function `hpsa_free_sas_phy': (.text+0x1ce874): undefined reference to `sas_port_delete_phy' (.text+0x1ce87c): undefined reference to `sas_phy_free' drivers/built-in.o: In function `hpsa_alloc_sas_port': (.text+0x1ceb9c): undefined reference to `sas_port_alloc_num' (.text+0x1ceba8): undefined reference to `sas_port_add' drivers/built-in.o: In function `hpsa_init': (.init.text+0x8838): undefined reference to `sas_attach_transport' (.init.text+0x8868): undefined reference to `sas_release_transport This adds 'select SCSI_SAS_ATTR' in the Kconfig entry, just like we do for all other drivers using those functions. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: d04e62b9d63a ("hpsa: add in sas transport class") Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Don Brace <don.brace@pmcs.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * scsi: advansys needs ISA dma api for ISA supportArnd Bergmann2015-11-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The advansys drvier uses the request_dma function that is used on ISA machines for the internal DMA controller, which causes build errors on platforms that have ISA slots but do not provide the ISA DMA API: drivers/scsi/advansys.c: In function 'advansys_board_found': drivers/scsi/advansys.c:11300:10: error: implicit declaration of function 'request_dma' [-Werror=implicit-function-declaration] The problem now showed up in ARM randconfig builds after commit 6571fb3f8b7f ("advansys: Update to version 3.5 and remove compilation warning") made it possible to build on platforms that have neither VIRT_TO_BUS nor ISA_DMA_API but that do have ISA. This adds the missing dependency. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * scsi_sysfs: protect against double execution of __scsi_remove_device()Vitaly Kuznetsov2015-11-191-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On some host errors storvsc module tries to remove sdev by scheduling a job which does the following: sdev = scsi_device_lookup(wrk->host, 0, 0, wrk->lun); if (sdev) { scsi_remove_device(sdev); scsi_device_put(sdev); } While this code seems correct the following crash is observed: general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC RIP: 0010:[<ffffffff81169979>] [<ffffffff81169979>] bdi_destroy+0x39/0x220 ... [<ffffffff814aecdc>] ? _raw_spin_unlock_irq+0x2c/0x40 [<ffffffff8127b7db>] blk_cleanup_queue+0x17b/0x270 [<ffffffffa00b54c4>] __scsi_remove_device+0x54/0xd0 [scsi_mod] [<ffffffffa00b556b>] scsi_remove_device+0x2b/0x40 [scsi_mod] [<ffffffffa00ec47d>] storvsc_remove_lun+0x3d/0x60 [hv_storvsc] [<ffffffff81080791>] process_one_work+0x1b1/0x530 ... The problem comes with the fact that many such jobs (for the same device) are being scheduled simultaneously. While scsi_remove_device() uses shost->scan_mutex and scsi_device_lookup() will fail for a device in SDEV_DEL state there is no protection against someone who did scsi_device_lookup() before we actually entered __scsi_remove_device(). So the whole scenario looks like that: two callers do simultaneous (or preemption happens) calls to scsi_device_lookup() ant these calls succeed for both of them, after that they try doing scsi_remove_device(). shost->scan_mutex only serializes their calls to __scsi_remove_device() and we end up doing the cleanup path twice. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * st: fix potential null pointer dereference.Maurizio Lombardi2015-11-191-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If cdev_add() returns an error, the code calls cdev_del() passing the STm->cdevs[rew] pointer as parameter; the problem is that the pointer has not been initialized yet. This patch fixes the problem by moving the STm->cdevs[rew] pointer initialization before the call to cdev_add(). It also sets STm->devs[rew] and STm->cdevs[rew] to NULL in case of failure. Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * scsi: report 'INQUIRY result too short' once per hostVitaly Kuznetsov2015-11-191-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some host adapters (e.g. Hyper-V storvsc) are known for not respecting the SPC-2/3/4 requirement for 'INQUIRY data (see table ...) shall contain at least 36 bytes'. As a result we get tons on 'scsi 0:7:1:1: scsi scan: INQUIRY result too short (5), using 36' messages on console. This can be problematic for slow consoles. Introduce short_inquiry flag in struct Scsi_Host to print the message once per host. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * advansys: fix big-endian buildsArnd Bergmann2015-11-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Building the advansys driver in a big-endian configuration such as ARM allmodconfig shows a warning: drivers/scsi/advansys.c: In function 'adv_build_req': include/uapi/linux/byteorder/big_endian.h:32:26: warning: large integer implicitly truncated to unsigned type [-Woverflow] #define __cpu_to_le32(x) ((__force __le32)__swab32((x))) drivers/scsi/advansys.c:7806:22: note: in expansion of macro 'cpu_to_le32' scsiqp->sense_len = cpu_to_le32(SCSI_SENSE_BUFFERSIZE); It turns out that the commit that introduced this used the cpu_to_le32() incorrectly on an 8-bit field, which results in the sense_len to always be set to zero, as the SCSI_SENSE_BUFFERSIZE value gets moved to upper byte of the 32-bit intermediate. This removes the cpu_to_le32() call to restore the original version. I found this only by looking at the compiler output and have not done a full review for possible further endianess bugs in the same driver. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 811ddc057aac ("advansys: use DMA-API for mapping sense buffer") Reviewed-by: Hannes Reinecke <hare@suse.de> Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * qla2xxx: Fix rwlock recursionBart Van Assche2015-11-171-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following kernel bug: kernel:BUG: rwlock recursion on CPU#2, insmod/39333, ffff8803e998cb28 kernel: Call Trace: kernel: [<ffffffff812bce44>] dump_stack+0x48/0x64 kernel: [<ffffffff810a8047>] rwlock_bug+0x67/0x70 kernel: [<ffffffff810a833a>] do_raw_write_lock+0x8a/0xa0 kernel: [<ffffffff815f3033>] _raw_write_lock_irqsave+0x63/0x80 kernel: [<ffffffffa08087c8>] qla82xx_rd_32+0xe8/0x140 [qla2xxx] kernel: [<ffffffffa0808845>] qla82xx_crb_win_lock+0x25/0x60 [qla2xxx] kernel: [<ffffffffa0808976>] qla82xx_wr_32+0xf6/0x150 [qla2xxx] kernel: [<ffffffffa0808ac0>] qla82xx_disable_intrs+0x50/0x80 [qla2xxx] kernel: [<ffffffffa080630a>] qla82xx_reset_chip+0x1a/0x20 [qla2xxx] kernel: [<ffffffffa07d6ef2>] qla2x00_initialize_adapter+0x132/0x420 [qla2xxx] kernel: [<ffffffffa08087c8>] qla82xx_rd_32+0xe8/0x140 [qla2xxx] kernel: [<ffffffffa0808845>] qla82xx_crb_win_lock+0x25/0x60 [qla2xxx] kernel: [<ffffffffa0808976>] qla82xx_wr_32+0xf6/0x150 [qla2xxx] kernel: [<ffffffffa0808ac0>] qla82xx_disable_intrs+0x50/0x80 [qla2xxx] kernel: [<ffffffffa080630a>] qla82xx_reset_chip+0x1a/0x20 [qla2xxx] kernel: [<ffffffffa07d6ef2>] qla2x00_initialize_adapter+0x132/0x420 [qla2xxx] kernel: [<ffffffffa07c964e>] qla2x00_probe_one+0xefe/0x2130 [qla2xxx] kernel: [<ffffffff8130052c>] local_pci_probe+0x4c/0xa0 kernel: [<ffffffff81300603>] pci_call_probe+0x83/0xa0 kernel: [<ffffffff813008cf>] pci_device_probe+0x7f/0xb0 kernel: [<ffffffff813e2e83>] really_probe+0x133/0x390 kernel: [<ffffffff813e3139>] driver_probe_device+0x59/0xd0 kernel: [<ffffffff813e3251>] __driver_attach+0xa1/0xb0 kernel: [<ffffffff813e0cdd>] bus_for_each_dev+0x8d/0xb0 kernel: [<ffffffff813e28ee>] driver_attach+0x1e/0x20 kernel: [<ffffffff813e2252>] bus_add_driver+0x1d2/0x290 kernel: [<ffffffff813e3970>] driver_register+0x60/0xe0 kernel: [<ffffffff813009e4>] __pci_register_driver+0x64/0x70 kernel: [<ffffffffa04bc1cb>] qla2x00_module_init+0x1cb/0x21b [qla2xxx] kernel: [<ffffffff8100027d>] do_one_initcall+0xad/0x1c0 kernel: [<ffffffff810e2859>] do_init_module+0x69/0x210 kernel: [<ffffffff810e4e5c>] load_module+0x5cc/0x750 kernel: [<ffffffff810e5162>] SyS_init_module+0x92/0xc0 kernel: [<ffffffff815f37d7>] entry_SYSCALL_64_fastpath+0x12/0x6f Fixes: 8dfa4b5a9b44 ("qla2xxx: Fix sparse annotation") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by: Chad Dupuis <chad.dupuis@qlogic.com> Cc: Giridhar Malavali <giridhar.malavali@qlogic.com> Cc: Xose Vazquez Perez <xose.vazquez@gmail.com> Cc: stable <stable@vger.kernel.org> # v4.3+ Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * hpsa: logical vs bitwise AND typoDan Carpenter2015-11-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HPSA_DIAG_OPTS_DISABLE_RLD_CACHING is a mask and bitwise AND was intended here instead of logical &&. This bug is essentially harmless, it means that sometimes we don't print a warning message which we wanted to print. Fixes: c2adae44e916 ('hpsa: disable report lun data caching') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: Don Brace <don.brace@pmcs.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mvsas: don't allow negative timeoutsDan Carpenter2015-11-131-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is a static checker warning here because "val" is controlled by the user and we have a upper bound on it but allow negative numbers. "val" appears to be a timeout in usec so this bug probably means we have a longer timeout than we should. Let's fix this by changing "val" to unsigned. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mpt3sas: Fix use sas_is_tlr_enabled API before enabling ↵Sreekanth Reddy2015-11-131-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MPI2_SCSIIO_CONTROL_TLR_ON flag Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request message, check whether TLR is enabled on the drive using 'sas_is_tlr_enabled' API. Actually in the driver code, driver is using below API's 1. sas_enable_tlr() - to enable the TLR 2. sas_disable_tlr() - to disable the TLR 3. sas_is_tlr_enabled() - to check whether TLR is enabled or not. but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API, instead we checking for TLR bit from flag field of driver's 'struct MPT3SAS_DEVIC' structure. which is corrected with this patch. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * | Revert "scsi: Fix a bdi reregistration race"Bart Van Assche2015-12-021-11/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SCSI sd driver probes SCSI devices asynchronously. The sd_remove() function, called indirectly by device_del(), waits until asynchronous probing has finished. Since the block layer queue must only be cleaned up after probing has finished, device_del() has to be called before blk_cleanup_queue(). Hence revert commit bf2cf3baa20b. Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: <stable@vger.kernel.org> Signed-off-by: James Bottomley <JBottomley@Odin.com>
* | | qla2xxx: Fix regression introduced by target configFS changesHimanshu Madhani2015-11-281-1/+1
|/ / | | | | | | | | | | | | | | | | | | | | | | | | this patch fixes following regression # targetcli [Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable' Fixes: 2eafd72939fd ("target: use per-attribute show and store methods") Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* | Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds2015-11-13109-32627/+6477
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull final round of SCSI updates from James Bottomley: "Sorry for the delay in this patch which was mostly caused by getting the merger of the mpt2/mpt3sas driver, which was seen as an essential item of maintenance work to do before the drivers diverge too much. Unfortunately, this caused a compile failure (detected by linux-next), which then had to be fixed up and incubated. In addition to the mpt2/3sas rework, there are updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus an assortment of changes including some year 2038 issues, a fix for a remove before detach issue in some drivers and a couple of other minor issues" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits) mpt3sas: fix inline markers on non inline function declarations sd: Clear PS bit before Mode Select. ibmvscsi: set max_lun to 32 ibmvscsi: display default value for max_id, max_lun and max_channel. mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl() scsi: pmcraid: replace struct timeval with ktime_get_real_seconds() mvumi: 64bit value for seconds_since1970 be2iscsi: Fix bogus WARN_ON length check scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice mpt3sas: Bump mpt3sas driver version to 09.102.00.00 mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs mpt2sas, mpt3sas: Update the driver versions mpt3sas: setpci reset kernel oops fix mpt3sas: Added OEM Gen2 PnP ID branding names mpt3sas: Refcount fw_events and fix unsafe list usage mpt3sas: Refcount sas_device objects and fix unsafe list usage mpt3sas: sysfs attribute to report Backup Rail Monitor Status mpt3sas: Ported WarpDrive product SSS6200 support mpt3sas: fix for driver fails EEH, recovery from injected pci bus error mpt3sas: Manage MSI-X vectors according to HBA device type ...
| * | mpt3sas: fix inline markers on non inline function declarationsStephen Rothwell2015-11-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After merging the scsi tree, today's linux-next build (powerpc allyesconfig) failed like this: In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0: drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_io_done': drivers/scsi/mpt3sas/mpt3sas_base.h:1414:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_get': function body not available mpt3sas_scsi_direct_io_get(struct MPT3SAS_ADAPTER *ioc, u16 smid); ^ drivers/scsi/mpt3sas/mpt3sas_scsih.c:4448:6: error: called from here if (mpt3sas_scsi_direct_io_get(ioc, smid) && ^ In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0: drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io); ^ drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here mpt3sas_scsi_direct_io_set(ioc, smid, 0); ^ In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:5 9:0: drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io); ^ drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here mpt3sas_scsi_direct_io_set(ioc, smid, 0); ^ Presumably caused by commit c84b06a48c4d ("mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: James Bottomley <JBottomley@Odin.com>
| * | Merge tag '4.4-scsi-mkp' into miscJames Bottomley2015-11-1264-31760/+5765
| |\| | | | | | | | | | | | | | | | SCSI queue for 4.4. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * sd: Clear PS bit before Mode Select.Gabriel Krisman Bertazi2015-11-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to SPC-4, in a Mode Select, the PS bit in Mode Pages is reserved and must be set to 0 by the driver. In the sd implementation, function cache_type_store does a Mode Sense, which might set the PS bit on the read buffer, followed by a Mode Select, which receives the same buffer, without explicitly clearing the PS bit. So, in cases where target supports saving the Mode Page to a non-volatile location, we end up doing a Mode Select with the PS bit set, which could cause an illegal request error if the target is checking this. This was observed on a new firmware change, which was subsequently reverted, but this changes sd.c to be more compliant with SPC-4. This patch clears the PS bit in the buffer returned by Mode Select, right before it is used in the Mode Select command. Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * ibmvscsi: set max_lun to 32Laurent Vivier2015-11-112-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | As defined in 4.6.9 of SAM-4, the encoding of LUN is on 5 bits (max_lun=32) and the current value is only 8. Set max_lun to IBMVSCSI_MAX_LUN (32). Signed-off-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * ibmvscsi: display default value for max_id, max_lun and max_channel.Laurent Vivier2015-11-111-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | As devices with values greater than that are silently ignored, this gives some hints to the sys admin to know why he doesn't see his devices... Signed-off-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()Alison Schofield2015-11-111-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace the use of struct timeval and do_gettimeofday() with 64 bit ktime_get_real_seconds. Prevents 32-bit type overflow in year 2038 on 32-bit systems. Driver was using the seconds portion of struct timeval (.tv_secs) to pass a millseconds timestamp to the firmware. This change maintains that same behavior using ktime_get_real_seconds. The structure used to pass the timestamp to firmware is 48 bits and works fine as long as the top 16 bits are zero and they will be zero for a long time..ie. thousands of years. Alternative Change: Add sub second granularity to timestamp As noted above, the driver only used the seconds portion of timeval, ignores the microseconds portion, and by multiplying by 1000 effectively does a <<10 and always writes zero into timestamp[0]. The alternative change would pass all the bits to the firmware: struct timespec64 ts; ktime_get_real_ts64(&ts); timestamp = ts.tv_sec * MSEC_PER_SEC + ts.tv_nsec / NSEC_PER_MSEC; Signed-off-by: Alison Schofield <amsfield22@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mvumi: 64bit value for seconds_since1970Tina Ruchandani2015-11-111-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | struct mvumi_hs_page2 stores a "seconds_since1970" field which is of type u64. It is however, written to, using 'struct timeval' which has a 32-bit seconds field and whose value will overflow in year 2038. This patch uses ktime_get_real_seconds() instead since it provides a 64-bit seconds value, which is 2038 safe. Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * be2iscsi: Fix bogus WARN_ON length checkTim Gardner2015-11-111-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | drivers/scsi/be2iscsi/be_main.c: In function 'be_sgl_create_contiguous': drivers/scsi/be2iscsi/be_main.c:3187:18: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses] WARN_ON(!length > 0); gcc version 5.2.1 Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Cc: Jayamohan Kallickal <jayamohan.kallickal@avagotech.com> Cc: Minh Tran <minh.tran@avagotech.com> Cc: John Soni Jose <sony.john-n@avagotech.com> Cc: "James E.J. Bottomley" <JBottomley@odin.com> Reported-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * scsi_scan: don't dump trace when scsi_prep_async_scan() is called twiceVitaly Kuznetsov2015-11-111-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The only user of scsi_prep_async_scan() is scsi_scan_host() and it handles the situation correctly. Move 'called twice' reporting to debug level as well. The issue is observed on Hyper-V: on any device add/remove event storvsc driver calls scsi_scan_host() and in case previous scan is still running we get the message and stack dump on console. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Alex Ng <alexng@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mpt3sas: Bump mpt3sas driver version to 09.102.00.00Sreekanth Reddy2015-11-111-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Bump mpt3sas driver version to 09.102.00.00 Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAsSreekanth Reddy2015-11-1114-826/+566
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modified the mpt3sas driver to have a single driver module which supports both SAS 2.0 & SAS 3.0 HBA devices. * Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table. * Created two separate SCSI host templates for SAS2 and SAS3 HBAs so that, during the driver load time driver can use corresponding host template(based the pci device ID) while registering a scsi host adapter instance for that pci device. * Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for SAS3 HBAs. Also updated the code to make sure that mpt2ctl device processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl device processes only those ioctl cmds issued for the SAS3 HBAs. * Added separate indexing for SAS2 and SAS3 HBAs. * Replaced compile time check 'MPT2SAS_SCSI' to run time check 'hba_mpi_version_belonged' whereever needed. * Aliased this merged driver to mpt2sas using MODULE_ALIAS. * Moved global varaible 'driver_name' to per adapter instance variable. * Created two raid function template and used corresponding raid function templates based on the run time check 'hba_mpi_version_belonged'. * Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and renamed it as mpt3sas_warpdrive.c. * Also renamed the functions in mpt3sas_warpdrive.c file to follow current driver function name convention. * Updated the Makefile to build mpt3sas_warpdrive.o file for these WarpDrive-specific functions. * Also in function mpt3sas_setup_direct_io(), used sector_div() API instead of division operator (which gives compilation errors on 32 bit machines). * Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file. * Added module parameter 'hbas_to_enumerate' which permits using this merged driver as a legacy mpt2sas driver or as a legacy mpt3sas driver. Here are the available options for this module parameter: 0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs 1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs 2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs * Removed mpt2sas entries from SCSI's Kconfig and Makefile files. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mpt2sas, mpt3sas: Update the driver versionsSreekanth Reddy2015-11-111-5/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bump the mpt2sas driver version to 20.102.00.00 and Bump the mpt3sas driver version to 9.101.00.00. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Acked-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mpt3sas: setpci reset kernel oops fixSreekanth Reddy2015-11-114-9/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | setpci reset on nytro warpdrive card along with sysfs access and cli ioctl access resulted in kernel oops 1. pci_access_mutex lock added to provide synchronization between IOCTL, sysfs, PCI resource handling path 2. gioc_lock spinlock to protect list operations over multiple controllers This patch is ported from commit 6229b414b3ad ("mpt2sas: setpci reset kernel oops fix"). Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Acked-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mpt3sas: Added OEM Gen2 PnP ID branding namesSreekanth Reddy2015-11-112-114/+305
| | | | | | | | | | | | | | | | | | | | | | | | | | | Added OEM Gen2 PnP ID branding names from mpt2sas driver. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Acked-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * mpt3sas: Refcount fw_events and fix unsafe list usageSreekanth Reddy2015-11-111-22/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The fw_event_work struct is concurrently referenced at shutdown. Add a refcount to protect it and refactor the code to use it. Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no longer iterates over the list without holding the lock since _firmware_event_work() concurrently deletes items from the list. This patch is ported from commit 008549f6e8a1 ("mpt2sas: Refcount fw_events and fix unsafe list usage"). These changes are also required for mpt3sas. Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Acked-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
OpenPOWER on IntegriCloud