summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/mwifiex/cfg80211.c
Commit message (Collapse)AuthorAgeFilesLines
* mwifiex: remove low priority scan handlingAmitkumar Karwar2014-09-151-8/+0
| | | | | | | | | | | | | We have a logic in driver to delay or abort low priority scan to serve Tx traffic effectively. With scan channel gap support added, firmware now allows driver to send Tx data while scan operation is in progress. Hence low priority scan handling in driver is not required now. This patch removes related code. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: bring in scan channel gap featureAvinash Patil2014-09-151-0/+5
| | | | | | | | | | | | | | | | | | With scan channel gap when any station/AP is active, FW comes back to connected channel for any pending data transfter after scanning each channel. We set scan channel gap TLV to FW in scan command when any of the interface is active. This enables scan channel gap in FW. Also when scan channel gap is enabled, we would scan maximum channels allowed by FW. Scan channel gap is supported only on FW with V15 FW API. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: set passive scan type for scan requests with no ssidAvinash Patil2014-09-151-1/+1
| | | | | | | | | | | | It was observed that station would sent probe request even when scan type has been set as passive during iw scan. This was happening because driver sets passive scan type only when channel has IEEE80211_CHAN_NO_IR flag set. Along with this, add condition to check if no ssids are specified in scan request so as to mark such scan request passive. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge tag 'mac80211-next-for-john-2014-08-29' of ↵John W. Linville2014-09-041-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg <johannes@sipsolutions.net> says: "Not that much content this time. Some RCU cleanups, crypto performance improvements, and various patches all over, rather than listing them one might as well look into the git log instead." Signed-off-by: John W. Linville <linville@tuxdriver.com> Conflicts: drivers/net/wireless/ath/wil6210/wmi.c
| * cfg80211: allow passing frame type to cfg80211_inform_bss()Johannes Berg2014-08-261-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | When using the cfg80211_inform_bss[_width]() functions drivers cannot currently indicate whether the data was received in a beacon or probe response. Fix that by passing a new enum that indicates such (or unknown). For good measure, use it in ath6kl. Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl] Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mwifiex: fix decimal printf format specifiers prefixed with 0xHans Wennborg2014-08-251-1/+1
|/ | | | | | | | | | | The prefix suggests the number should be printed in hex, so use the %x specifier to do that. Found by using regex suggested by Joe Perches. Signed-off-by: Hans Wennborg <hans@hanshq.net> Acked-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge tag 'master-2014-07-25' of ↵David S. Miller2014-07-281-3/+5
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next John W. Linville says: ==================== pull request: wireless-next 2014-07-25 Please pull this batch of updates intended for the 3.17 stream! For the mac80211 bits, Johannes says: "We have a lot of TDLS patches, among them a fix that should make hwsim tests happy again. The rest, this time, is mostly small fixes." For the Bluetooth bits, Gustavo says: "Some more patches for 3.17. The most important change here is the move of the 6lowpan code to net/6lowpan. It has been agreed with Davem that this change will go through the bluetooth tree. The rest are mostly clean up and fixes." and, "Here follows some more patches for 3.17. These are mostly fixes to what we've sent to you before for next merge window." For the iwlwifi bits, Emmanuel says: "I have the usual amount of BT Coex stuff. Arik continues to work on TDLS and Ariej contributes a few things for HS2.0. I added a few more things to the firmware debugging infrastructure. Eran fixes a small bug - pretty normal content." And for the Atheros bits, Kalle says: "For ath6kl me and Jessica added support for ar6004 hw3.0, our latest version of ar6004. For ath10k Janusz added a printout so that it's easier to check what ath10k kconfig options are enabled. He also added a debugfs file to configure maximum amsdu and ampdu values. Also we had few fixes as usual." On top of that is the usual large batch of various driver updates -- brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action. Rafał has also been very busy with b43 and related updates. Also, I pulled the wireless tree into this in order to resolve a merge conflict... P.S. The change to fs/compat_ioctl.c reflects a name change in a Bluetooth header file... ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * mwifiex: do not re-associate when already connectedUjjal Roy2014-07-181-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In managed mode if the driver is getting a re-associate command from cfg80211, driver deauthenticates with the AP internally and sends a disconnected event to cfg80211 before completion of its association process. The disconnected event then modifies the SSID length as wdev->ssid_len = 0. So, upon receiving the connect result event from driver, cfg80211 is unable to get that BSS from the device's BSS list and generates the following WARN_ON message. WARNING: CPU: 0 PID: 857 at net/wireless/sme.c:658 __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]() Avoid re-association while the device is already associated to a network. Also remove the internal deauthentication from the association path. Signed-off-by: Ujjal Roy <royujjal@gmail.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | net: set name_assign_type in alloc_netdev()Tom Gundersen2014-07-151-1/+2
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert all users to pass NET_NAME_UNKNOWN. Coccinelle patch: @@ expression sizeof_priv, name, setup, txqs, rxqs, count; @@ ( -alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs) +alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs) | -alloc_netdev_mq(sizeof_priv, name, setup, count) +alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count) | -alloc_netdev(sizeof_priv, name, setup) +alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup) ) v9: move comments here from the wrong commit Signed-off-by: Tom Gundersen <teg@jklm.no> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵John W. Linville2014-07-101-0/+1
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
| * mwifiex: initialize Tx/Rx info of a packet correctlyAmitkumar Karwar2014-07-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | There are few places at the begining of Tx/Rx paths where tx_info/rx_info is not correctly initialized. This patch takes care of it. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | wireless: mwifiex: Use the proper interfacesThomas Gleixner2014-06-251-3/+1
| | | | | | | | | | | | | | | | | | | | | | Why is converting time formats so desired if there are proper interfaces for this? Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Bing Zhao <bzhao@marvell.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | Revert "mwifiex: Use the proper interfaces"Bing Zhao2014-06-251-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit a82fc3b4a2bceb7c6587249cb690342eb5065979. Thomas corrected me on that I misunderstood Johannes' comment for net_timedelta() and the ktime_get_real() usage inside __net_timestamp(). Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: John W. Linville <linville@tuxdriver.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mwifiex: update Copyright to 2014Xinming Hu2014-06-251-1/+1
| | | | | | | | | | | | | | | | This patch updates mwifiex Copyright to 2014. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-nextJohn W. Linville2014-06-251-1/+2
|\ \
| * | cfg80211: pass TDLS initiator in tdls_mgmt operationsArik Nemtsov2014-06-231-1/+2
| |/ | | | | | | | | | | | | | | | | | | The TDLS initiator is set once during link setup. If determines the address ordering in the link identifier IE. Fix dependent drivers - mwifiex and mac80211. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mwifiex: Use the proper interfacesThomas Gleixner2014-06-201-3/+1
| | | | | | | | | | | | | | | | | | Why is converting time formats so desired if there are proper interfaces for this? Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mwifiex: support wowlan magic-packet encapsulated as UDP packetZhiyuan Yang2014-06-191-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When magic-packet is generated as a UDP packet the offset should be 20+8 more bytes to cover IPv4 header and UDP header. So the total offset become 56. Add a new MEF entry to support both magic-packet patterns generated by different tools. Cc: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Zhiyuan Yang <yangzy@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | mwifiex: Remove custom world regulatory domainMarkus Pargmann2014-06-191-36/+0
|/ | | | | | | | | | | | | | A custom regulatory domain was introduced in this commit: cc0ba0d mwifiex: support custom world regulatory domain The commit description says that it was introduced because the world regulatory domain does not include channels 52-64 and 100-140. These channels are described in the world regulatory domain now, so we can drop this custom regulatory domain. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: constify MAC addresses in cfg80211 opsJohannes Berg2014-05-191-10/+9
| | | | | | This propagates through all the drivers and mac80211. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mwifiex: update MCS set as per RX-STBC bit from hostapdMaithili Hinge2014-03-191-3/+3
| | | | | | | | | | | To set AP in 1X1 or 2X2 mode through hostapd, we need to set RX-STBC* in hostapd.conf file. Depending upon RX-STBC bit in ht_cap IE received from hostapd, we need to update mcs set in bss_cfg appropriately before starting AP. Signed-off-by: Maithili Hinge <maithili@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: use VHT MCS mask in set bitrate mask handlerAmitkumar Karwar2014-03-141-2/+10
| | | | | | | | | As V15 firmware supports VHT rate configuration, we can use this information received in set bitrate mask handler. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: update MCS information as per antenna settingsAmitkumar Karwar2014-02-281-2/+29
| | | | | | | | | | | | | Even if the device is changed to 1X1 mode, data is sent with higher MCS rates after association. This patch fixes the problem by updating MCS information field in HT capability when antenna setting changes so that correct information will be advertised in association and probe request. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: remove global variable cmd_wait_q_requiredBing Zhao2014-02-281-86/+81
| | | | | | | | | | | | | | | There is a race condition while queuing synchronous command and asynchronous command requested from different threads, because the wait_q_enabled flag is set based on a global variable cmd_wait_q_required. The issue is fixed by removing this global variable and using a unified function with an argument 'sync' passed into the function. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: enable obss scan offload feature flagAmitkumar Karwar2014-02-241-1/+2
| | | | | | | | | We don't perform OBSS scan internally. As we intend to use corresponding feature in application, we will enable this flag. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: Pass TDLS peer capability information in tdls_mgmtSunil Dutt Undekari2014-02-201-2/+2
| | | | | | | | | | | | | | | | While framing the TDLS Setup Confirmation frame, the driver needs to know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the VHT/HT operation / WMM parameter elements accordingly. Supplicant determines if the TDLS peer is VHT/HT/WMM capable based on the presence of the respective IEs in the received TDLS Setup Response frame. The host driver should not need to parse the received TDLS Response frame and thus, should be able to rely on the supplicant to indicate the capability of the peer through additional flags while transmitting the TDLS Setup Confirmation frame through tdls_mgmt operations. Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mwifiex: add cfg80211 change_station handler supportAvinash Patil2014-02-121-0/+25
| | | | | | | | | | This patch adds cfg80211 change_station handler support for mwifiex which is needed for TDLS link setup. Driver creates a command to modify peer link capabilities and issues command to FW. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: add cfg80211 add_station handler supportAvinash Patil2014-02-121-0/+18
| | | | | | | | | | This patch adds cfg80211 add_station handler support for mwifiex which is needed for TDLS setup. Driver issues create TDLS link command to FW upon receiving add_station from cfg80211. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: add cfg80211 tdls_oper handler supportAvinash Patil2014-02-121-0/+49
| | | | | | | | | | | | This patch adds cfg80211 handler tdls_oper handler support to mwifiex. Upon enable link, driver sets status as TDLS status as setup complete and also sets AMSDU size, AMPDU params for direct link. Upon disable link, driver issues command to FW to delete this link in FW. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: add tdls_mgmt handler supportAvinash Patil2014-02-121-0/+81
| | | | | | | | | | | | This patch adds support for TDLS management frames transmit handler. mwifiex driver supports TDLS with external support, i.e. expects user space application to form TDLS frames. Same is advertised to cfg80211 during registration. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: remove unsupported code in 11acBing Zhao2014-02-121-3/+0
| | | | | | | | bit12 in fw_cap_info is for testing only. Remove all related code. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: fix channel configuration in IBSS joinAntonio Quartulli2014-02-041-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When receiving an IBSS_JOINED event select the BSS object based on the {bssid, channel} couple rather than the bssid only. With the current approach if another cell having the same BSSID (but using a different channel) exists then cfg80211 picks up the wrong BSS object. The result is a mismatching channel configuration between cfg80211 and the driver, that can lead to any sort of problem. The issue can be triggered by having an IBSS sitting on given channel and then asking the driver to create a new cell using the same BSSID but with a different frequency. By passing the channel to cfg80211_get_bss() we can solve this ambiguity and retrieve/create the correct BSS object. All the users of cfg80211_ibss_joined() have been changed accordingly. Moreover WARN when cfg80211_ibss_joined() gets a NULL channel as argument and remove a bogus call of the same function in ath6kl (it does not make sense to call cfg80211_ibss_joined() with a zero BSSID on ibss-leave). Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: Bing Zhao <bzhao@marvell.com> Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi> Cc: libertas-dev@lists.infradead.org Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> [minor code cleanup in ath6kl] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: Clean up connect params and channel fetchingJouni Malinen2014-02-041-2/+3
| | | | | | | | | | Addition of the frequency hints showed up couple of places in cfg80211 where pointers could be marked const and a shared function could be used to fetch a valid channel. Signed-off-by: Jouni Malinen <j@w1.fi> [fix mwifiex] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mwifiex: fix wakeup on magic packetAndreas Fenkart2014-01-231-1/+1
| | | | | | | | | | | | | | | | 8 bytes preamble 14 bytes src/dst/eth_type 6 bytes 0xff:0xff.. http://en.wikipedia.org/wiki/Wake-on-LAN#Magic_packet http://en.wikipedia.org/wiki/EtherType This will fail if we VLAN or the magic packet is encapsulated as a UDP packet... Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: export threshold value and retry limit to cfg80211Ujjal Roy2014-01-161-0/+14
| | | | | | | | | While registering the driver with cfg80211, update the threshold value and retry limit to cfg80211. Signed-off-by: Ujjal Roy <royujjal@gmail.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: use a function to replace two copies of a code fragmentBing Zhao2014-01-091-8/+1
| | | | | | | | | Instead of having two copies of the code for device tree cfgdata downloading, add a function to improve the code. Reviewed-by: Paul Stewart <pstew@chromium.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: download per country tx power table to firmwareBing Zhao2013-12-181-0/+10
| | | | | | | | | | | | | | When driver gets regulatory domain change notifications or before associates to an AP with Country IE, the txpwrlimit table stored in device tree for that country is downloaded to firmware. The txpwrlimit downloading will happen only at the first time when the alpha2 country code is changed. World regulatory domain "00" notification doesn't trigger the downloading. This behavior is same as domain_info command. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: send regulatory domain info to firmware only if alpha2 changedBing Zhao2013-12-181-6/+13
| | | | | | | | | | | | On cfg80211 regulatory domain change, drivers gets alpha2 country code or "00" in driver's notification handler. In most cases, the pattern will be US, 00, US, 00, US, 00, US, ... There is no need to send domain info to firmware in case of "00" or with the same alpha2 country code. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge remote-tracking branch 'wireless-next/master' into mac80211-nextJohannes Berg2013-12-161-4/+20
|\
| * mwifiex: correct TX byte count statisticsUjjal Roy2013-12-091-0/+1
| | | | | | | | | | | | | | | | | | | | The skb is modified in sending the TX packet. Save the original packet length to a variable so that we can get the correct statistics update. Signed-off-by: Ujjal Roy <royujjal@gmail.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * Merge branch 'for-john' of ↵John W. Linville2013-12-021-12/+13
| |\ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
| * | mwifiex: fix potential mem leak in .del_virtual_intfAmitkumar Karwar2013-11-151-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1) Currently we freeing wdev for each interface in driver unload path. We may leak memory if user have already deleted an interface. mwifiex_add_virtual_intf() allocates wdev structure. So it should be freed in mwifiex_del_virtual_intf(). This will make sure that wdev will be freed when user deletes an interface and also in unload path. 2) "priv->netdev->ieee80211_ptr" should also be cleared in mwifiex_del_virtual_intf. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mwifiex: failure path handling in mwifiex_add_virtual_intf()Amitkumar Karwar2013-11-151-4/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1) If register_netdevice() is failed, we are freeing netdev pointer, but priv->netdev is not cleared. This gives kernel paging request error when driver is unloaded or interface is deleted. Fix the problem by clearing the pointer. 2) Fix memory leak issue by freeing 'wdev' in failure paths. Also, clear priv->wdev pointer. As mwifiex_add_virtual_intf() successfully handles the failure conditions, redundant code under err_add_intf label is removed in this patch. Reported-by: Ujjal Roy <royujjal@gmail.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | cfg80211: in bitrate_mask, rename mcs to ht_mcsJanusz Dziedzic2013-12-051-3/+3
| |/ |/| | | | | | | | | | | | | | | Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also rename mcs to ht_mcs in struct cfg80211_bitrate_mask. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> [reword commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | cfg80211: aggregate mgmt_tx parameters into a structAndrei Otcheretianski2013-12-021-3/+3
| | | | | | | | | | | | | | | | | | | | | | Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params struct to aggregate parameters for mgmt_tx functions. This makes the functions' signatures less clumsy and allows less painful parameters extension. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> [fix all other drivers] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | cfg80211: move regulatory flags to their own variableLuis R. Rodriguez2013-11-251-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We'll expand this later, this will make it easier to classify and review what things are related to regulatory or not. Coccinelle only missed 4 hits, which I had to do manually, supplying the SmPL in case of merge conflicts. @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags |= REGULATORY_CUSTOM_REG @@ expression e; @@ -e->flags |= WIPHY_FLAG_CUSTOM_REGULATORY +e->regulatory_flags |= REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags &= ~REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_CUSTOM_REGULATORY +wiphy->regulatory_flags & REGULATORY_CUSTOM_REG @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags |= REGULATORY_STRICT_REG @@ expression e; @@ -e->flags |= WIPHY_FLAG_STRICT_REGULATORY +e->regulatory_flags |= REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags &= ~REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_STRICT_REGULATORY +wiphy->regulatory_flags & REGULATORY_STRICT_REG @@ struct wiphy *wiphy; @@ -wiphy->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS @@ expression e; @@ -e->flags |= WIPHY_FLAG_DISABLE_BEACON_HINTS +e->regulatory_flags |= REGULATORY_DISABLE_BEACON_HINTS @@ struct wiphy *wiphy; @@ -wiphy->flags &= ~WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags &= ~REGULATORY_DISABLE_BEACON_HINTS @@ struct wiphy *wiphy; @@ -wiphy->flags & WIPHY_FLAG_DISABLE_BEACON_HINTS +wiphy->regulatory_flags & REGULATORY_DISABLE_BEACON_HINTS Generated-by: Coccinelle SmPL Cc: Julia Lawall <julia.lawall@lip6.fr> Cc: Peter Senna Tschudin <peter.senna@gmail.com> Cc: Mihir Shete <smihir@qti.qualcomm.com> Cc: Henri Bahini <hbahini@qca.qualcomm.com> Cc: Tushnim Bhattacharyya <tushnimb@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> [fix up whitespace damage, overly long lines] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | cfg80211: consolidate passive-scan and no-ibss flagsLuis R. Rodriguez2013-11-251-7/+7
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These two flags are used for the same purpose, just combine them into a no-ir flag to annotate no initiating radiation is allowed. Old userspace sending either flag will have it treated as the no-ir flag. To be considerate to older userspace we also send both the no-ir flag and the old no-ibss flags. Newer userspace will have to be aware of older kernels. Update all places in the tree using these flags with the following semantic patch: @@ @@ -NL80211_RRF_PASSIVE_SCAN +NL80211_RRF_NO_IR @@ @@ -NL80211_RRF_NO_IBSS +NL80211_RRF_NO_IR @@ @@ -IEEE80211_CHAN_PASSIVE_SCAN +IEEE80211_CHAN_NO_IR @@ @@ -IEEE80211_CHAN_NO_IBSS +IEEE80211_CHAN_NO_IR @@ @@ -NL80211_RRF_NO_IR | NL80211_RRF_NO_IR +NL80211_RRF_NO_IR @@ @@ -IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR +IEEE80211_CHAN_NO_IR @@ @@ -(NL80211_RRF_NO_IR) +NL80211_RRF_NO_IR @@ @@ -(IEEE80211_CHAN_NO_IR) +IEEE80211_CHAN_NO_IR Along with some hand-optimisations in documentation, to remove duplicates and to fix some indentation. Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> [do all the driver updates in one go] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mwifiex: drop gratuitous ARP framesAvinash Patil2013-08-261-0/+1
| | | | | | | | | | | | This patch adds support for dropping gratuitous ARP frames which is requirement for WFA Hotspot2.0. Hotspot2.0 capability is enabled in driver if extended capabilities IE from BSS descriptor has 11u interworking enabled. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: fix build error when CONFIG_PM is not setBing Zhao2013-08-121-2/+2
| | | | | | | | | | | | | | | | | | | | | config: make ARCH=m68k allmodconfig All error/warnings: drivers/net/wireless/mwifiex/cfg80211.c: In function 'mwifiex_fill_coalesce_rule_info': >> drivers/net/wireless/mwifiex/cfg80211.c:2493:3: error: implicit declaration of function 'mwifiex_is_pattern_supported' [-Werror=implicit-function-declaration] drivers/net/wireless/mwifiex/cfg80211.c: At top level: drivers/net/wireless/mwifiex/cfg80211.c:2537:12: warning: 'mwifiex_cfg80211_set_coalesce' defined but not used [-Wunused-function] cc1: some warnings being treated as errors Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: add packet coalesce supportAmitkumar Karwar2013-08-091-0/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Coalesce filters are configured in firmware based on settings received from cfg80211. Packet type which is required by firmware is determined based on provided patterns in a rule: Unicast: if pattern '01' with offset 0 is found Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found Some example coalesce configuration files: 1) Coalesce Rx data packets from 192.168.0.88 mac address of our device is 00:50:43:21:53:7A Source IP address offset comes out as 52 after following calculations: 32 bytes of HW 802.11 header + 8 bytes LLC + 12 bytes in IPV4 header till source IP address Destination mac is at offset 6 in HW header. delay=100 condition=1 patterns=01,6+00:50:43:22,10+53:7A,52+c0:a8:00:58 2) Coalesce all broadcast and multicast packets(Multiple packet types are not allowed in a single rule. Hence created separate rules) delay=400 condition=1 patterns=33:33 delay=400 condition=1 patterns=ff:ff:ff:ff Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
OpenPOWER on IntegriCloud