summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
Commit message (Collapse)AuthorAgeFilesLines
...
| * | ath10k: remove work in progress logs from snoc driverGovind Singh2018-12-202-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All the necessary patches to make wifi running (over SNOC) are merged and tested on SDM845/QCS404 platform with WCN3990 wifi module, hence remove work in progress debug from snoc driver and Kconfig. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath10k: fix warning due to msdu limit errorBhagavathi Perumal S2018-12-204-4/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some hardwares variants (QCA99x0) are limiting msdu deaggregation with some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to avoid excessive MSDU-deaggregation in error cases. When number of sub frames exceeds the limit, target hardware will send all msdus starting from present msdu in RAW format as a single msdu packet and it will be indicated with error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor. This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211 header. It caused below warning message. [ 320.151332] ------------[ cut here ]------------ [ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188 In our issue case, MSDU limit error happened due to FCS error and generated this warning message. This fixes the warning by handling the MSDU limit error. If msdu limit error happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit in QOS header so that upper layer processes this frame if it is valid or drop it if FCS error set. And removed the warning message, hence partial msdus without first msdu is expected in msdu limit error cases. Tested on QCA9984, Firmware 10.4-3.6-00104 Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath10k: disable 4addr source port learning in 10.4 FW by defaultSathishkumar Muruganandam2018-12-203-1/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently in 10.4 FW, all the received 4addr frames are processed for source port learning which is enabled by default. This learning can't be disabled by default in FW since it breaks backward compatibility. Since ath10k uses mac80211 based 4addr mode, source port learning done in 10.4 FW is redundant and also causes issues when 3addr frames are transmitted/received for a 4addr station. One such visible functional impact is when GTK rekey frame from hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled with 4addr is already allowed for receiving 3addr EAPOL frames. Source port learning implementation in 10.4 FW drops this 3addr GTK rekey frame in AP destinated for 4addr STA causing disassociation and re-association for every GTK rekey session. GTK rekey issue is not seen when learning is disabled in FW. To prevent such issues without breaking backward compatibility, FW advertises new service bit making the source port learning configurable and this learning is being currently disabled during ath10k vdev creation. * Tested HW: QCA9984 * Tested FW: 10.4-3.6.0.1-00004 Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath10k: report tx rate using ieee80211_tx_rate_update()Anilkumar Kolli2018-12-203-5/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mesh path metric needs tx rate information from ieee80211_tx_status() call but in ath10k there is no mechanism to report tx rate information via ieee80211_tx_status(), the tx rate is only accessible via sta_statiscs() op. Per peer tx stats has tx rate info available, Tx rate is available to ath10k driver after every 4 PPDU sent in the air. For each PPDU, ath10k driver updates rate informattion to mac80211 using ieee80211_tx_rate_update(). Per peer txrate information is updated through per peer statistics and is available for QCA9888/QCA9984/QCA4019/QCA998X only Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053 Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath10k: add amsdu support for monitor modeYu Wang2018-12-201-2/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu is larger than the tailroom of the rx skb, skb_over_panic issue will happen when calling skb_put. In monitor mode, amsdu will be handled in this path, and msdu_len of the first msdu_desc is the length of the entire amsdu, which might be larger than the maximum length of a skb, in such case, it will hit the issue upon. To fix this issue, process msdu list separately for monitor mode. Successfully tested with: QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1). Signed-off-by: Yu Wang <yyuwang@codeaurora.org> [kvalo@codeaurora.org: cosmetic cleanup] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath10k: fix kernel panic due to use after freeKarthikeyan Periyasamy2018-12-201-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This issue arise in a race condition between ath10k_sta_state() and ath10k_htt_fetch_peer_stats(), explained in below scenario Steps: 1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST state. 2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message. In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after the peer validation check. Since arsta->tx_stats get freed before the peer deletion [1]. ath10k_htt_fetch_peer_stats() ended up in "use after free" situation. Fixed this issue by moving the arsta->tx_stats free handling after the peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in "use after free" situation. Kernel Panic: Unable to handle kernel NULL pointer dereference at virtual address 00000286 pgd = d8754000 [00000286] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP ARM ... CPU: 0 PID: 6245 Comm: hostapd Not tainted task: dc44cac0 ti: d4a38000 task.ti: d4a38000 PC is at kmem_cache_alloc+0x7c/0x114 LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core] pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013 sp : d4a39b88 ip : 00000000 fp : 00000001 r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0 r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286 r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00 Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c5787d Table: 5a75406a DAC: 00000015 Process hostapd (pid: 6245, stack limit = 0xd4a38238) Stack: (0xd4a39b88 to 0xd4a3a000) ... [<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core]) [<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211]) [<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211]) [<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211]) [<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat]) [<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c) [<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac) [<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34) [<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204) [<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370) [<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84) [<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228) [<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70) [<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44) Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003) ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon Hardware tested: QCA9984 Firmware tested: 10.4-3.6.0.1-00004 Fixes: a904417fc ("ath10k: add extended per sta tx statistics support") Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath10k: remove set but not used variable 'num_tdls_vifs'YueHaibing2018-12-201-26/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state': drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning: variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable] 'num_tdls_vifs' not used any more after 9a993cc1ea95 ("ath10k: fix the logic of limiting tdls peer counts") Also, remove the single called function ath10k_mac_tdls_vifs_count and ath10k_mac_tdls_vifs_count_iter. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | wil6210: remove set but not used variable 'wdev'YueHaibing2018-12-201-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/ath/wil6210/main.c: In function '_wil6210_disconnect': drivers/net/wireless/ath/wil6210/main.c:407:23: warning: variable 'wdev' set but not used [-Wunused-but-set-variable] It never used since commit ("e1b43407c034 wil6210: refactor disconnect flow") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | wil6210: convert to DEFINE_SHOW_ATTRIBUTEYangtao Li2018-12-201-198/+42
| | | | | | | | | | | | | | | | | | | | | Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath6kl: Use debug instead of error message when disabledKyle Roeschley2018-12-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This is not an unexpected condition, so we don't need to be shouting to the world about it. Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath6kl: Fix off by one error in scan completionKyle Roeschley2018-12-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When ath6kl was reworked to share code between regular and scheduled scans in commit 3b8ffc6a22ba ("ath6kl: Configure probed SSID list consistently"), probed SSID entry changed from 1-index to 0-indexed. However, ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its indexing so that we correctly clear out the probed SSID list. Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | ath6kl: Only use match sets when firmware supports itKyle Roeschley2018-12-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan") merged the probed and matched SSID lists before sending them to the firmware. In the process, it assumed match set support is always available in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check that the firmware supports matching SSIDs in scheduled scans before setting MATCH_SSID_FLAG. Fixes: dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan") Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-12-205-2/+44
|\ \ \ | |/ / |/| | | | | | | | | | | | | | | | | | | | | | | Lots of conflicts, by happily all cases of overlapping changes, parallel adds, things of that nature. Thanks to Stephen Rothwell, Saeed Mahameed, and others for their guidance in these resolutions. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | ath10k: skip sending quiet mode cmd for WCN3990Rakesh Pillai2018-12-195-2/+44
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HL2.0 firmware does not support setting quiet mode. If the host driver sends the quiet mode setting command to the HL2.0 firmware, it crashes with the below signature. fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0 The quiet mode command support is exposed by the firmware via thermal throttle wmi service. Enable ath10k thermal support if thermal throttle wmi service bit is set. 10.x firmware versions support this feature by default, but unfortunately do not advertise the support via service flags, hence have to manually set the service flag in ath10k_core_compat_services(). Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990. Co-developed-by: Govind Singh <govinds@codeaurora.org> Co-developed-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of ↵David S. Miller2018-12-0336-347/+866
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.21 First set of patches for 4.21. Most notable here is support for Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide nvram files for brcmfmac. Major changes: brcmfmac * add support for first trying to get a board specific nvram file * add support for getting nvram contents from EFI variables qtnfmac * use single PCIe driver for all platforms and rename Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE * add support for QSR1000/QSR2000 (Topaz) family of chipsets ath10k * add support for WCN3990 firmware crash recovery * add firmware memory dump support for QCA4019 wil6210 * add firmware error recovery while in AP mode ath9k * remove experimental notice from dynack feature iwlwifi * PCI IDs for some new 9000-series cards * improve antenna usage on connection problems * new firmware debugging infrastructure * some more work on 802.11ax * improve support for multiple RF modules with 22000 devices cordic * move cordic macros and defines to a public header file * convert brcmsmac and b43 to fully use cordic library ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * ath9k: dynack: remove 'experimental' tagLorenzo Bianconi2018-11-061-1/+1
| | | | | | | | | | | | | | | | | | Remove experimental tag from dynack Kconfig entry since it has been tested on outdoor 25Km links Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: dynack: make ewma estimation fasterLorenzo Bianconi2018-11-064-12/+29
| | | | | | | | | | | | | | | | | | | | In order to make propagation time estimation faster, use current sample as ewma output value during 'late ack' tracking Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: dynack: check da->enabled first in sampling routinesLorenzo Bianconi2018-11-061-2/+2
| | | | | | | | | | | | | | | | | | | | Check da->enabled flag first in ath_dynack_sample_tx_ts and ath_dynack_sample_ack_ts routines in order to avoid useless processing Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: dynack: move debug log after buffer incrementsLorenzo Bianconi2018-11-061-14/+12
| | | | | | | | | | | | | | | | | | | | Move debug log in ath_dynack_sample_tx_ts and ath_dynack_sample_ack_ts after timestamp buffer head/tail increments in order to make debugging more user friendly Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: dynack: use authentication messages for 'late' ackLorenzo Bianconi2018-11-061-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | In order to properly support dynack in ad-hoc mode running wpa_supplicant, take into account authentication frames for 'late ack' detection. This patch has been tested on devices mounted on offshore high-voltage stations connected through ~24Km link Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: fix struct init whitespace in SNOC driverBrian Norris2018-11-061-6/+6
| | | | | | | | | | Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: don't assume this is a PCI dev in generic codeBrian Norris2018-11-061-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Not all devices using this driver are backed by a PCI device, so it's not fair to assume 'to_pci_dev()' is valid. Fortunately, we only were using this to convert straight back to a bare 'device', which means we were only doing no-op pointer arithmetic, and not actually accessing potentially out-of-bounds memory. But this is still bad practice. Just use 'ar->dev' directly, since that's really all we're looking for. Fixes: 209b2a68de76 ("ath10k: add platform regulatory domain support") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: assign 'n_cipher_suites' for WCN3990Brian Norris2018-11-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 2ea9f12cefe4 ("ath10k: add new cipher suite support") added a new n_cipher_suites HW param with a fallback value and a warning log. Commit 03a72288c546 ("ath10k: wmi: add hw params entry for wcn3990") later added WCN3990 HW entries, but it missed the n_cipher_suites. Rather than seeing this warning every boot ath10k_snoc 18800000.wifi: invalid hw_params.n_cipher_suites 0 let's provide the appropriate value. Cc: Rakesh Pillai <pillair@qti.qualcomm.com> Cc: Govind Singh <govinds@qti.qualcomm.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: ath10k_snoc_{read,write}32() should be staticBrian Norris2018-11-062-4/+2
| | | | | | | | | | | | | | | | | | They're provided as callbacks in ath10k_hif_ops and should be accessed that way, if needed outside of snoc.c, and anyway, they're currently unused outside snoc.c. Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: snoc: fix unbalanced clock error handlingBrian Norris2018-11-061-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Similar to regulator error handling, we should only start tearing down the 'i - 1' clock when clock 'i' fails to enable. Otherwise, we might end up with an unbalanced clock, where we never successfully enabled the clock, but we try to disable it anyway. Fixes: a6a793f98786 ("ath10k: vote for hardware resources for WCN3990") Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: snoc: relax voltage requirementsBrian Norris2018-11-061-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I rarely see drivers specify precise voltage requirements like this, but if we really have to...let's at least give a little wiggle room. Board designs (and accompanying device trees) may not provide exactly the voltage listed here, and we shouldn't fail to probe just because of this. Round these ranges down to the nearest volt, and provide a 0.05V margin. The regulator should provide its own supported ranges, which will helpfully intersect with these ranges. I would just as well remove these ranges entirely, but if I understand correctly, there's some reason that QCOM SoC's like to set zero / non-zero voltages. Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: snoc: fix unabalanced regulator error handlingBrian Norris2018-11-061-54/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a regulator fails to set its voltage, we end up with an unbalanced call to regulator_disable(), because the error path starts with the current regulator (which was never enabled). Factor out the "on" function to perform (and unwind if failed) a single regulator at a time, and then main loop (ath10k_snoc_vreg_on()) can just worry about unwinding the regulators that were already enabled. It also helps to factor out the "off" function, to avoid repeating some code here. Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: snoc: remove 'wcn3990' from generic resource handlingBrian Norris2018-11-062-21/+21
| | | | | | | | | | | | | | | | | | | | ath10k_wcn3990_clk_info and ath10k_wcn3990_vreg_info are not WCN3990-specific structures. They hold generic data. So don't name them with wcn3990 specifics. Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: fix locking in wmi_callLior David2018-11-061-4/+5
| | | | | | | | | | | | | | | | | | Switch from spin_lock to spin_lock_irqsave, because wmi_ev_lock is used inside interrupt handler. Signed-off-by: Lior David <liord@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: fix freeing of rx buffers in EDMA modeAhmad Masri2018-11-061-30/+14
| | | | | | | | | | | | | | | | | | | | | | After being associated with some EDMA rx traffic, upon "down" driver doesn't free all skbs in the rx ring. Modify wil_move_all_rx_buff_to_free_list to loop on active list of rx buffers, unmap the physical memory and free the skb. Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: remove unnecessary alignment code from rx flowAhmad Masri2018-11-061-6/+4
| | | | | | | | | | | | | | | | | | Rx buffers in EDMA mode are initialized to 4 bytes aligned size. Remove the unnecessary alignment code applied on rx buffer size. Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: fix RGF_CAF_ICR address for Talyn-MBMaya Erez2018-11-062-2/+10
| | | | | | | | | | | | | | | | RGF_CAF_ICR register location has changed in Talyn-MB. Add RGF_CAF_ICR_TALYN_MB to support the new address. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: fix L2 RX status handlingMaya Erez2018-11-061-11/+12
| | | | | | | | | | | | | | | | | | | | L2 RX status errors should not be treated as a bitmap and the actual error values should be checked. Print L2 errors as wil_err_ratelimited for easier debugging when such errors occurs. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: fix debugfs memory access alignmentAhmad Masri2018-11-061-5/+10
| | | | | | | | | | | | | | | | | | | | | | | | All wil6210 device memory access should be 4 bytes aligned. In io blob wil6210 did not force alignment for read function, this caused alignment fault on some platforms. Fixing that by accessing all 4 lower bytes and return to host the requested data. Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: add general initialization/size checksAlexei Avshalom Lazar2018-11-062-1/+3
| | | | | | | | | | | | | | | | Initialize unset variable, and verify that mid is valid. Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: notify cqm packet loss on disable_ap_smeAhmad Masri2018-11-061-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | wil6210 used to notify cfg80211_del_sta on every fw disconnect event. In disable_ap_sme mode the userspace manages the protocol SME and FW sends disconnect event only due to link loss. In disable_ap_sme mode, indicate CQM packet loss to let the host control the connection and disconnect the link if needed. Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: refactor disconnect flowAhmad Masri2018-11-065-72/+147
| | | | | | | | | | | | | | | | | | Separate sending command to the fw from the event handling function to simplify the disconnect flow and track the from_event flag correctly. Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: fix memory leak in wil_find_tx_bcast_2Lior David2018-11-061-0/+2
| | | | | | | | | | | | | | | | | | | | A successful call to wil_tx_ring takes skb reference so it will only be freed in wil_tx_complete. Consume the skb in wil_find_tx_bcast_2 to prevent memory leak. Signed-off-by: Lior David <liord@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: add recovery for FW error while in AP modeDedy Lansky2018-11-063-8/+120
| | | | | | | | | | | | | | | | | | | | AP configuration is stored by the driver. Upon FW error, disconnect notification is sent to user space for any associated stations. AP is then internally restarted with the stored configuration. Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: make sure Rx ring sizes are correlatedDedy Lansky2018-11-064-7/+12
| | | | | | | | | | | | | | | | | | | | | | When enlarging rx_ring_order module param, wil6210 fails to load because there are not enough Rx buffers. Fix this by enlarging number of Rx buffers at startup, if needed based on rx_ring_order. Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: increase RX rings and RX buff array sizeMaya Erez2018-11-064-5/+11
| | | | | | | | | | | | | | | | | | | | | | In Talyn-MB, the 11ad throughput is higher and performance drops may occur in the current RX configuration due to unavailability of Rx buffers. Increase the RX descriptor ring, RX status ring and number of RX buffers to stabilize the performance in high throughput. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: fix reset flow for Talyn-mbAlexei Avshalom Lazar2018-11-061-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | With current reset flow, Talyn sometimes get stuck causing PCIe enumeration to fail. Fix this by removing some reset flow operations that are not relevant for Talyn. Setting bit 15 in RGF_HP_CTRL is WBE specific and is not in use for all wil6210 devices. For Sparrow, BIT_HPAL_PERST_FROM_PAD and BIT_CAR_PERST_RST were set as a WA an HW issue. Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * wil6210: remove fake support for RXHASHHamad Kadmany2018-11-062-10/+1
| | | | | | | | | | | | | | | | | | | | Setting the same fake hash to all skbs prevents distributing different flows to different CPU cores. Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org> Signed-off-by: Lior David <liord@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath10k: fix some typoYangtao Li2018-11-061-2/+2
| | | | | | | | | | Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * carl9170: tx: mark expected switch fall-throughsGustavo A. R. Silva2018-11-051-0/+3
| | | | | | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * carl9170: rx: mark expected switch fall-throughGustavo A. R. Silva2018-11-051-0/+1
| | | | | | | | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1056534 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath6kl: Mark expected switch fall-throughGustavo A. R. Silva2018-11-051-0/+1
| | | | | | | | | | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 201383 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Steve deRosier <derosier@cal-sierra.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: remove set but not used variable 'new_flags'zhong jiang2018-11-051-3/+1
| | | | | | | | | | | | | | | | new_flags is not used after setting its value. It is safe to remove the unused variable. Signed-off-by: zhong jiang <zhongjiang@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: hw: mark expected switch fall-throughGustavo A. R. Silva2018-11-051-0/+1
| | | | | | | | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1056532 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: ar9002_phy: mark expected switch fall-throughsGustavo A. R. Silva2018-11-051-1/+1
| | | | | | | | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1056532 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
OpenPOWER on IntegriCloud