| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
Remove arch/arm/plat-omap/include/plat/clock.h by merging it into
arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h.
The goal here is to facilitate ARM single image kernels by removing
includes via the "plat/" symlink.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fixed to remove duplicate clock.h includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\
| |
| |
| |
| |
| |
| | |
Conflicts:
arch/arm/mach-omap2/clkt34xx_dpll3m2.c
arch/arm/mach-omap2/clkt_clksel.c
arch/arm/mach-omap2/clock.c
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As part of Common Clk Framework (CCF) the clk_enable() operation
was split into a clk_prepare() which could sleep, and a clk_enable()
which should never sleep. Similarly the clk_disable() was
split into clk_disable() and clk_unprepare(). This was
needed to handle complex cases where in a clk gate/ungate
would require a slow and a fast part to be implemented.
None of the clocks below seem to be in the 'complex' clocks
category and are just simple clocks which are enabled/disabled
through simple register writes.
Most of the instances also seem to be called in non-atomic
context which means its safe to move all of those from
using a clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare().
For some others, mainly the ones handled through the hwmod framework
there is a possibility that they get called in either an atomic
or a non-atomic context.
The way these get handled below work only as long as clk_prepare
is implemented as a no-op (which is the case today) since this gets
called very early at boot while most subsystems are unavailable.
Hence these are marked with a *HACK* comment, which says we need
to re-visit these once we start doing something meaningful with
clk_prepare/clk_unprepare like doing voltage scaling or something
that involves i2c.
This is in preparation of OMAP moving to CCF.
Based on initial changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
| |\ \
| |/
| |
| |
| |
| |
| |
| | |
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Find and unwrap wrapped strings in the style:
pr_debug("clockdomain: hardware cannot set/clear wake up of "
"%s when %s wakes up\n", clkdm1->name, clkdm2->name);
Keeping these strings contiguous seems to be the current Linux kernel
policy.
The offending lines were found with the following command:
pcregrep -rnM '"\s*$\s*"' arch/arm/*omap*
While here, some messages have been clarified, some pr_warning(
... calls have been converted to pr_warn( ..., and some printk(KERN_*
... have been converted to pr_*.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Disable autoidle on all clocks during clock framework initialization.
(If CONFIG_PM is set, autoidle is re-enabled for all clocks later in
the boot process.)
The principle behind this patch, and some similar patches, is that the
kernel should start with all power management features disabled.
Later in the boot process, the PM code, if compiled in with CONFIG_PM,
enables or re-enables power management features.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The OMAP3 clock code contains some legacy code to allow the MPU rate
to be specified as a kernel command line parameter. If the 'mpurate'
parameter is specified, the kernel will attempt to switch the MPU rate
to this rate during boot. As part of this process, a short message
"Switched to new clocking rate" is generated -- and in this message,
the "Core" clock rate and "MPU" clock rate are transposed.
This patch ensures that the clock rates are displayed in the correct
order.
Thanks to Bruno Guerin <br.guerin@free.fr> for reporting this bug and
proposing a fix. Thanks to Richard Woodruff <r-woodruff2@ti.com> for
reviewing the problem and passing the report on.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Bruno Guerin <br.guerin@free.fr>
Cc: Richard Woodruff <r-woodruff2@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files. Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.
This process also requires the #includes in each of these files to be
changed to reference the new file name. As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.
Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
| |
|
|
|
|
|
|
| |
The OMAP2 and OMAP3 boot-time MPU rate change code is almost
identical. Merge them into mach-omap2/clock.c, and add kerneldoc
documentation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
|
clock34xx_data.c now contains data for the OMAP34xx family, the
OMAP36xx family, and the OMAP3517 family, so rename it to
clock3xxx_data.c. Rename clock34xx.c to clock3xxx.c, and move the
chip family-specific clock functions to clock34xx.c, clock36xx.c, or
clock3517.c, as appropriate. So now "clock3xxx.*" refers to the OMAP3
superset.
The main goal here is to prepare to compile chip family-specific clock
functions only for kernel builds that target that chip family. To get to
that point, we also need to add CONFIG_SOC_* options for those other
chip families; that will be done in future patches, planned for 2.6.35.
OMAP4 is also affected by this. It duplicated the OMAP3 non-CORE DPLL
clkops structure. The OMAP4 variant of this clkops structure has been
removed, and since there was nothing else currently in clock44xx.c, it
too has been removed -- it can always be added back later when there
is some content for it. (The OMAP4 clock autogeneration scripts have been
updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
|
